LABVIEW USART synchronization and one of the stm32

Similar Questions

• I'm trying to connect two monitors and one using the hdmi port and the other vga. How can I get the pc to recognize the two?

  Original title: multiple monitors

  I'm trying to connect two monitors and one using the hdmi port and the other vga. How can I get the pc to recognize the two?

  Hi David,

  Thanks for posting your query on the Microsoft Community.

  I suggest you refer to the Microsoft Help Articles below and try the steps mentioned.

  Check out the link:

  http://Windows.Microsoft.com/en-in/Windows-8/how-connect-multiple-monitors#1TC=T1

  You can also check:

  http://Windows.Microsoft.com/en-in/Windows-8/get-best-display-monitor

  Hope this information helps. Please let us know if you need any other help with Windows in the future. We will be happy to help you.

• LabView 8.5 and 2010 on the same computer running XP?

  Is it possible to install two version 8.5 and 2010 on the XP machine? And then work on some projects in Labview 8.5 and on other projects in Labview 2010 without a conflict?

  What about device drivers? What version of DAQ driver will work in both versions of Labview?

  Thanks a lot for any insite.

  Rita

  Always install older versions first. Some SDK don't play well with several versions of LabVIEW. With regard to the acquisition of data: http://digital.ni.com/public.nsf/allkb/F4E76EC05118F72D8625773000672298

• LabVIEW 6.1 and 2012 at the same computer problem

  Hello world.

  I've been using Labview 6.1 for a while and it worked fine for me.

  I recently installed Labview 2012 on the same computer and looks like the serial port of functions do not work properly. Whenever I try to open an example of VISA communication, labview freezes.

  I guess it's because even though I can install two versions of labview in the same computer, the drivers can be installed once correct?

  But I thought that labview 6.1 and 2012 may share the same VISA driver.

  Is there a way I can resolve this problem with versions of labview works correctly?

  Thanks in advanc.

  The LabVIEW and VISA compatibility chart is here. As you can see, there is no version of NI-VISA which is compatible with the two 2012 and your old 6.1. Indeed, the graphic poster not only any version of older than 7.1.1 LabvIEW.

• Windows live mail. I sent an email and one of the addresses is not valid. I want to remove

  I snet an email using direct and one email address in most parts was no longer valid. The sint message showing in my drafts but they live mail continues to try to send whenever I open or close the box with the letters. How can I remove this message so he'll quit trying to send?

  Hello

  I suggest you to post your problem in windows live community given that the issue is with Windows Live mail. Support team live Windows would be better for help you with this problem.

  http://windowslivehelp.com/community/

  Thanks and greetings
  Umesh P - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• How can I align two different text lines in the same table in two different directions (centered on one and one on the left)?

  Hello

  I want to focus the two different text lines that are in the same table, but one on the Center and the other on the left. I put a < span > tag in the hope that he was overwhelmed the family of police .bottomsel table class properties and the. Police-family Cig84 and color but the text-align only: they are both on the left.

  Here is my source and CSS codes:

  Source:

  < table width = "600" border = "0" >

  < b >

  < class td = "bottomref" > < p > < span class = "bottomsel" > | < a href = "index.html" target = "_self" > Main < /a > | " < a href = "about.html" target = "_self" > on < /a > | " < a href = "clients.html" target = "_self" > customers < /a > | " < a href = "contact.html" target = "_self" > Contact < /a > | " </span > < br / >

  < span class = 'credits' > credits: < span class = "Cig84" > Cig84 </span > < / span > < /p > < table >

  < /tr >

  < /table >

  CSS:

  {.bottomsel}

  text-align: center;

  do-family: Georgia, "Times New Roman", Times, serif;

  }

  {.credits}

  text-align: left;

  }

  . {Cig84}

  Color: #F00;

  do-family: "Comic Sans MS", cursive;

  }

  Use tags to paragraph with CSS classes.

  CSS:

  . Center {text-align: center}

  .the {text-align: left}

  HTML:

  This text is centered This text is left-aligned

  Nancy O.

• To convert my Keynote slideshow (09) .mov, I always end up with double blades on slides with sound, a sound and one without the sound. Why? How should I do?

  When trying to convert a Keynote slide show (09) in format .mov, I end up with double blades on slides that have sound. What makes the total video almost twice as long as I wish. How do the conversion with only sound slides appearing and eliminating silent rehearsals?

  You will need to confirm which version of Mac OS, and Keynote, you use as your profile shows very old software that is obsolete and is no longer supported. I assume his keynote address version 4 If you are using Mac G5.

  IV never heard of Keynote, do what you describe in any version, so we need the details of how you have the presentation put in place. If you post a sample file that illustrates this problem on Dropbox I review on my old power Mac.

• I was using Microsoft Fix and one of the messages for me was that "more than one user is currently connected to this computer"

  While checking on Microsoft 'Fixit' to see if everything was working OK, I got a message saying as follows: more o no user is currently connected to this computer. »

  I can't understand this because I am the only user on my computer.  No other Member of my family is using my computer, so can you help me this please?

  Thank you.

  Hi Deepak B,.

  Thank you very much for your help.  I did as you suggested.  First: the Safety Scanner did not find a malware, etc. on my computer, which is really good.

  Second - accounts - outside myself - on my computer. I was surprised to see there was a guest account as well as mine.  I now extinct 'guest account '.  I can think about is my daughter and her husband who make us visit once a year.  April, my daughter knows a lot about computers, so I think that it is the culprit!

  That is the problem solved, and I am grateful for your help.

  ElmGrove

• Meetings of synchronization and error in the sychronsing. Unknown error.

  Error message appears when I try to sync. Using-Vista, latest version of Firefox.

  Can you check this problem on Firefox 9?

  • getfirefox.com

• How do update you the "cloud-copy" of bookmarks in sync-ed, etc. (assuming that 'sync' only allows you to synchronize your device with the cloud

  The machine used for the first set up a sync account seems to provide the cloud 'Captain' at the time of installation. Subsequent operations 'sync now' any device seem to download this cloud 'master' on the devices. But how to update the 'master' cloud and it can be done (transferred to) by the device of your choice?

  Hi Igbortaz,
  This ONLY happens when you join the account the first device. After that, all devices connected to the account synchronization and merge with the stored then replaces the local profile. Unfortunately, at the moment it doesn't have a function to choose the device that is the master.

  And before any changes, I recommend you make a backup of your profile.

• Not able to boot after that windows update, just trying to install the number 3 setting 3, and then restart the computer. With the help of Windows Vista SP2

  Friday morning I wasn't able to boot my computer more. When I start my computer it won't seek to set a parameter nr 3 of 3. And then it restarts again. My computer tried to install some windows update settings the day before with no success. I Don t remember what it was. I got Vista SP2

  The same problem happends to my computer from friends four days, after she start a windows update installation. But it has solved its problem by using the Windows installation CD and use the repair tool.

  For me, my Windows installation CD I got from Dell does not work. Not the tool repair or startreparation. And I have no reference system to return.

  What should I do? I don't want to reinstall windows again, I have a lot of information on the computer I need to.

  All the world has noticed this problem?

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  See you soon.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the above does not work, try to make a Bootable ERD to do a Startup Repair:

  As is the case with most computers/laptops these days, they do not come with good Vista disc to repair only the recovery disks.

  As your grave in the category above, download the ISO on the link provided and make a bootdisk of it.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  You can make a tool to restart system, System Restore, etc. with it.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista repair disc.

  You can do a system restart tool, system, etc it restore.

  There is not a disk of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.
  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the ISP above Mathods to solve your problems, save your data using one of the methods below, and then reinstall Windows:

  1. slave of your hard drive in another computer and read/save your data out there.

  2. put your Hard drive in a USB hard drive case, plug it into another computer and read/save from there.

  3 Alternatively, use Knoppix Live CD to recover data:

  http://www.Knopper.NET/Knoppix/index-en.html

  Download/save the file Knoppix Live CD ISO above.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://isorecorder.alexfeinman.com/isorecorder.htm

  Download the Vista software from the link above.

  After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.

  Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.

  Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1 in the boot order.

  Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.

  When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.

  Click on the icons of hard drive to open and to understand which drive is which.

  Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons).

  Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.

  See you soon.

  Mick Murphy - Microsoft partner

• Stop synchronization of windows with the file is no longer available

  How to prevent synchronization of windows trying to sync with a folder that no longer exists? I'm working on a windows XP computer that had a network folder shared on our old domain controller. It was created to "work offline". This former DC has since died, but the XP machine is still trying to synchronize with him whenever he disconnects or connects.

  I tried to delete all the files temporary/offline, I tried windows Explorer and go to tools > Synchronize and then unchecking the file that does not exist. I tried to go to the configuration of the synchronization and UN-checking the folder to synchronize when connected to the LAN. Nothing seems to prevent synchronization attempt. There are also other folders that exist that I want to keep the synchronization with, so I don't want to completely disable synchronization. Does anyone know how to make so that he can stop sync with just this file?

  Hello

  You can try the troubleshooting steps provided in the link below in case you haven't tried them already.

  How to use offline files in Windows XP
  http://support.Microsoft.com/kb/307853

  For more assistance, you can publish the isuse on the link below.

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer/

• LabVIEW 8.6 and LV RT 8.5?

  Hello

  I wonder if it is possible for LabVIEW 8.6 in interface with a target of desktop running LabVIEW RT 8.5? I'm having a problem with the interface between the two different versions of LabVIEW, at the present time, I'm unable to update desktop target to the new version of LabVIEW RT because a number of my students have not the new version of LabVIEW so that they must have LabVIEW RT 8.5 running on the target. I know it is possible to work on the labview 8.6 and save for the previous version of labview before you deploy it to the target, I wonder if it is possible to deploy the project directly without having to register for the previous version of LV

  Thank you

  The RT version on the target must match the version of the Module of RT on the host, or you will get an access denied error or incompatibility of Version or something like that.

• Can the Sandisk Sansa Fuze 4 GB MP3 read podcasts one after the other

  For health reasons, I need to take a long walk after each meal.  For many years during my walks that I listened to podcasts on my wonderful old Sandisk sansa, who plays a podcast after the other without action from me until I have stop.  It's perfect here in the North when I walk in 30 below zero weather. I mean that I don't want to open my parka and out the player to move to the next podcast.  If I had to do, they would find me lying in the snow, Frost, like all the rest of those poor Devils who bought the wrong MP3 player.  Anyway, after years of using the plug-in on my old Sansa fuze is pretty much exhausted and the player must be replaced.  I buy a sansa clip, but had to return when I discovered that he has not played podcasts one after the other, automatically. (And it's also too small for my needs).  Before you buy a new 4 GB sansa fuse, so I need to know if this greatest player will play my podcasts consecutively and one after the other.  Your advice would be much appreciated.

  MrHat wrote:

  I currently use the Sansa e250 2 GB MP3 Fuze player Walkman.

  There is an e250 (2 GB) and a rocket. They are 2 totally different players. The "rocket" (original) replaced the e200 series model.

  But if your podcasts are placed in the Podcast folder (or even record Audio books) and then ranked in the same "Album" folder, they must play consecutively without stopping, regardless of the model of reader.

• Help, please! A master hard disk partition information lost and cannot start the Vista system

  I have Vista with my dell desktop computer.  I guess I got a virus that has deleted/messed my main hard drive.  All of sudden my computer was dead and when I try to restart, I found I can't boot the system.  I loaded the DVD for the resettlement of Dell to come with the computer and try to install it.  But it shows "Disk 0 unallocated space" with 222 GB and 'Disk 0 Partition 2 Recovery' with 10 GB.  I could not install Vista on the first, as it says "Windows must be installed on a partition formatted in NTFS.

  How could I solve this problem?  I could not allow me to format the drive because there a lot of data, that I just can't lose.

  Any help is very welcome!

  Marco

  http://support.Dell.com/

  Problem with the recovery process, contact Dell at the link above.

  It's recovery process from Dell, NOT Microsoft.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Try this to save your data:

  Data recovery:

  1. slave of your hard drive in another computer and read/save your data out there.

  2. put your Hard drive in a USB hard drive case, plug it into another computer and read/save from there.

  3 Alternatively, use Knoppix Live CD to recover data:

  http://www.Knopper.NET/Knoppix/index-en.html

  Download/save the file Knoppix Live CD ISO above.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://isorecorder.alexfeinman.com/isorecorder.htm

  Download the Vista software from the link above.

  After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.

  Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.

  Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1^st in the boot order.

  Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.

  When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.

  Click on the icons of hard drive to open and to understand which drive is which.

  Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons).

  Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.

  See you soon...

  Mick Murphy - Microsoft partner