Lan to lan VPN and VPNclient support at the same time?
Hello I have a 2811 router.
I put up as a VPN with Clients_vpn hub connect to it, and I used an IPSec on a stick configuration.
At the same time, I would need to use the same Lan - to - Lan IPSec router to other different sites 2.
I can't figure out how do it since I use already my 2811 as Concentrator VPN for Clients_vpn.
Y at - it a trick?
Thank you very much
Riccardo
Of course, here is an example of configuration of a router to be configured to stop static VPN LAN-to-LAN as customer VPN at the same time:
http://www.Cisco.com/en/us/products/ps5855/products_configuration_example09186a00809c7171.shtml
And another one for the router be configured to terminate dynamic LAN - to - LAN VPN as VPN Client:
http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a00801dddbb.shtml
Another example of setting right on the LAN-to-LAN VPN between 2 routers:
Hope that helps.
Tags: Cisco Security
Similar Questions
-
Impossible to use VMWare Server and Virtual PC at the same time?
I have a Win 7 box I use VirtualPC (unfortunately, VPN to the employer only supports the 32-bit Win XP).
If I try to start any virtual machines using VMWare Server, power on and then immediately off. Tried several different VMs.
However, if I disable VirtualPC, they all work normally.
Then... there at - it a known issue with the help of Virtual PC and VMWare Server at the same time?
BTW, I didn't see this problem when you use Virtual PC and VMWare Player at the same time.
VirtualPC leaves the CPU of the exploitation of VMX root, which is a restricted mode. VMware Server is problems to switch between legacy mode and long (this switch is prohibited when the CPU is in VMX root operation). The current versions of the workstation and the player are able to circumvent this restriction.
-
Should I iMatch and music Apple at the same time?
Is there a point I iMatch and music Apple at the same time?
These are two different services > iCloud library: understand the differences between music from Apple and iTunes game - Apple Support
-
Why I have Photo and Photos open at the same time?
Why I have Photo and Photos open at the same time?
When what's going on? When you connect a camera or a card reader?
Or after the Mac is restarted?
If this occurs after startup, check system preferences > users and groups.
Select your account and open the connection. Deselect the applications you want to open at startup.
If this happens when you connect a camera, open the iPhoto preferences > general.
Set the preference "Connecting camera opens" to "no application".
-
can I play the guitar and midi keyboards at the same time?
IM using the 3 main stage, I would like to play guitar and midi keyboards at the same time. I know that I can have more than one keyboard will at the same time, but I can't understand how to play the guitar too. I use a core Alesis 1 plug the guitar and a Keith McMillen 12 Step midi controller, he reads both just fine alone, but they play together. How can I get there? In addition, Im using a MacBook Pro OS X El Capitan.
Thank you
Mike
You add a bunch of audio channels and affect the Core 1 Alesis entry?
-
Should I connect to the display, the vga cable and Dvi cable at the same time. I have a FP7 1110
UNUSED - a connection only (from the source of the same cylinder head box) - always!
DVI has better quality.C.
-
Windows defender and norton antivirus at the same time?
can I run windows defender and norton antivirus at the same time? I have Windows 7 and a lot of memory
I have HP Pavilion PC p7-1254
Yes.
-
The SD card is accessible by a BB App and Windows Explorer at the same time?
Hello
My requirement is that the SD card must be consulted by a BB App and Windows Explorer at the same time. But the BB app I developed is able to access the SD card only when the mass storage mode is turned off. Is this how the BB has designed or is it possible to have some logical coding for this?
Thank you
No, this is not possible.
-
the two versions of Muse (2015.0 and 2015.1) at the same time
Hello dear Musers,
Is it possible to install both versions (2015.0 AND 2015.1) at the same time?
I manage several sites and I want to be able to update regularly (stable and bug release 2015.0) while slowly, tests and moving them to reagent (2015.1)? Also to start playing with the possibilities of delicate design in Muse.
I also have a site with complex effects of scrolling that should stay that way. I can't run the risk of not working after the update... at least I have a replacement with Animations of EDGE...
Thanks for the help.
J. Vallejo
If you an active member of Muse and can accept the terms of the non-disclosure agreement, my recommendation would be to join the beta program of Muse at http://museprerelease.com. At the moment the latest preliminary 2015.1 is always displayed and it is basically identical to the retail version, but with a splash screen different. In general, it is deleted shortly after the production version is released, but has not yet happened.
The preliminary version installs the construction of shipping along the coast. The two have no overlap, other than the fact by double clicking a .muse file is a bit of a gamble in terms of what version of Muse, the operating system decides to launch.
-
I want to open two different pdf documents and view them at the same time so I can read a whole watching the other document. I use Acrobat DC and whenever I open a document, it creates a tab and I can only examine a document at a time. Is it possible to display two or more documents without having to toggle tabs?
Don't think that will work, but you can drag the tab to a new window. Each window can have a set of tabs.
-
How to transform a layer object and a path at the same time?
Hi all
I know that I will start when you tell me the answer to this!
I would really like to know if there is a way I can manage to transform a layer object and a path at the same time... or if there is no work around to get there.
In a Word, for example I spend a VERY long time to create a drive complex around a very detailed object and then at the end note to what twisted and perspective, and would like to straighten.
Of course I could turn and correct the object and then carefully turn the path - but it will not correct and I have to spend a lot of time the path of adjustment and make SURE, it is perfect.
Are there not somehow, I was able to transform set?
Usually, of course, I do all the correction to straighten and correct the perspective in advance, but in some cases after I am done creating the path I then notice that image could have used other adjustments.
I appreciate all the advice you can get :)
Thank you kindly,
Christine
Transform the layer and then target the way and make "Edit > Transform path > Again. If you make several changes on the layer, and then each time that validate you and leave transformation mode, remember to do the ' transform path > Again "to keep the layer and the synchronized pathname.
-
DHCP and static IP at the same time?
Simple scenario. My internet connection using DHCP and my home network uses a 10.x.x.x (static) addresses. How can I add an address static 10.0.0.x, in addition to the IP address provided by DHCP, if I can use internet and LAN at the same time? Under linux, it's pretty simple: ip addr add 10.0.0.1/24 dev eth0
You cannot use two IP addresses on a single ethernet interface, if you are using DHCP, you cannot add a static IP, it is technically impossible, in this case you must use two NICs, i.e. two different interfaces. If you connect to the Internet via the DHCP protocol and you have another PC which allows you to build a local network then you you may not change the dynamic address, but can replace the LAN address is dynamic/static. For example, if the PC that has the Internet connection, add another NETWORK card, then connect the second PC with this new NIC card. Now turn on sharing on the first PC Internet connection interface and so the two PC will be able to run the home networking and Internet connectivity. You don't even need to add a static IP address.
-
Hello
I have a fixed computer Windows 7, I need to configure for the use of wire and wireless networks.
On the phone we transfer vast amounts of data, astronomy cameras than only products of 20 to 30 seconds, space images 3-4 GB each. The cameras are connected to the top of a tower, which in turn is connected via a 45 feet cable CAT-5 to the search engine.
Internet access requires a wireless network connection.
These two connections work - separately. I have to disable an and activate the other to pass. This jump back and foth is obviously a bit inconvenient.
How to configure Windows 7 to manage both types of networks at the same time? On another forum I learned this kind of configuration is called multihoming, and it's something difficult to achieve.
Having studied more about it, there is another possible solution called Internet connection sharing. that may be easier. I haven't used this option for years (since the routers were introduced) but is still active.
Disable DHCP on the Dovado or use a cable between the PC and the laptop.
Turn on the wireless on the PC and make sure that you have an internet connection. Disable wireless on the laptop. Connect the PC's LAN ports and laptop (via router or a cable crossover).
IN the network of PCs and next to the connections Sharing Center, you must have 2 Ethernet and WiFi options. Double click on WiFi, then on the next screen, click Properties.
The second tab in the next screen is sharing, check allow other users of the network to connect and then OK.
Define the IP addresses for PC and laptop as in my previous post, but this time on the laptop set the default gateway to the IP address of the Wired of the PC port, the 1st DNS to the address of the Huawei and value of secondary school who suggested for your ISP.
This affects your PC to access wireless internet and allows the laptop to access the internet via the PC
Basic information about ICS are HERE
Manuals for the Dovado HERE
-
Static and dynamic NAT at the same time?
Is this possible? Let's say you have 20 public address pool and you have 30 computers LAN. You want to assign the same public address for some of the servers. And the rest can get the addresses of the pool at random.
It would be nice if we can easily do the appropriate firewall rules.
Yes, it is possible, you can use nat and global commands for dynamic conversion and use the static commands for static translation at the same time.
Here is an example:
Public rate IP-range outdoors: xxx.xxx.xxx.0/27
(IP addresses are xxx.xxx.xxx.1 - xxx.xxx.xxx.30)
Private range of IP addresses on the inside: yyy.yyy.yyy.0/24
In the example I'm going to static translate xxx.xxx.xxx.2 to yyy.yyy.yyy.2 Server1 (ditto for server2, but by using adresse.3)
All other IP addresses is translated dynamics.
Here is an example of how you can do this:
IP address outside xxx.xxx.xxx.1 255.255.255.224
IP address yyy.yyy.yyy.1 255.255.255.0 inside
NAT (inside) 0 access-list sheep
NAT (inside) 1 yyy.yyy.yyy.0 255.255.255.0
Global 1 interface (outside)
public static yyy.yyy.yyy.2 xxx.xxx.xxx.2 (indoor, outdoor)
public static yyy.yyy.yyy.3 xxx.xxx.xxx.3 (indoor, outdoor)
access-list deny ip host yyy.yyy.yyy.2 sheep all
access-list deny ip host yyy.yyy.yyy.3 sheep all
access-list sheep ip allow a whole
Kind regards
Leo
-
This only occurs in firefox 16.0.2 but not in chrome. In the Task Manager, I see FlashPlayerPlugin_11_4_402_287.exe 2 times and 2 times plugin - container.exe. At the same time my cpu starts to rise the temp and the computer freezes. Everything starts to work when I close flash video in youtube. Firefox functioned well before the last update for 16.0.2.
Start Firefox in Safe Mode to check if one of the extensions (Firefox/tools > Modules > Extensions) or if hardware acceleration is the cause of the problem (switch to the DEFAULT theme: Firefox/tools > Modules > appearance).
- Do not click on the reset button on the start safe mode window or make changes.
- https://support.Mozilla.org/KB/safe+mode
- https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes
You can check the problems caused by the recent updates of Flash and try these:
- disable an eventual extension of the browser for Firefox Plugin RealPlayer Record and if installed RealPlayer update
- disable the safe_mode in Flash 11.3 and later versions
- turn off hardware acceleration in the Flash plugin
Maybe you are looking for
-
Old files to PRINT are not open
I have a file that will not open because it says it's old. How do I update?
-
Start button and associated icons/elements
All while browsing a Web site and try to get to the screen to move from left to right unsucessfully, I left said site and discovered that my start (the one with the windows icon) button and icons/Articles related to it, that use to be from left to ri
-
After upgrading to SP3 of XP SP2, the games is works more slowly or doesn't do at all
After upgrading to XP SP2 Sp3, games run more slowly or not at all
-
After restoring my system to Windows Vista, my screen resolution is incorrect.
Screwed up resolution :( I had to restore my computer to Windows vista after putting 7 window on it... now my screen resolution is turned off, it is the top of the screen to the bottom, but has 2 black bars on the sides... Ive already tried to settle
-
two items exactly close to each other
HelloI have two points, point A and point B. I want that they in one line to close between them, no space.I tried css, but have still some problems.googled and got links to the presentation of the grid, but still they are online, but not more close t