Laptop suddenly loses the wireless out of sleep mode

Similar Questions

• Re: Satellite L670 loses the wireless connection

  Hello

  I have a Satellite L670 - 1 H 1, a new laptop that runs Windows 7, with all the drivers and software uptodate, including the wireless card.

  I have a BT Home Hub 3 with an Edimax EW 7416APN v2 300 m range extender to help boost the signal in the kitchen area.

  The laptop works fine when I stay in the room where the reception centre. If I move in the kitchen the laptop will usually lose the wireless connection after a few minutes and I cannot get it back unless I turn the LAPTOP works and return to the Home Hub.

  I see no obvious reason to this problem. Two other laptop computers used in the home, more a smartphone stay connected with full signal in every corner of the House, at any time.

  I have to use the range extender, but is it possible that the laptop Toshiba just don't hear well with it?

  Any advice would be welcome.

  Thank you
  Canton

  Hello Canton

  As you know quality of connection WLAN depends on different factors is not easy to say why you have this problem, WLAN. I use Toshiba laptops for a long time now and I didn't notice in the past some serious question of WLAN.
  For example I'm 4 router with standard g and have very good signal even in the cellar too or out in the back yard.

  If possible, try to test the WLAN connection elsewhere. Maybe your friends have WLAN routers so you can test it.

  You have a new router or old?
  What WLAN standard do you use (b/g/n)?

• all-in-one 7510 loses the wireless connection

  We just bought a HP Photosmart 7510. She created fine with a wireless connection to our office for Vista 64-bit. After awhile, he loses the wireless connection. If I close the printer then turn on again, it resets the connection and works very well. I read that it can lose connection if it goes into sleep mode, and it seems that is what is happening. My question is, is there a way to keep the impression of loss of connection or enter the mode 'sleep'? Or do we have to put the printer only whenever we wanted to print, copy or scan? If so, the printer is adjustable to disable instead of switch mode 'sleep'?

  Already set to 'off '. I found this thread http://h30434.www3.hp.com/t5/Printer-Networking-and-Wireless/7510-photosmart-printer-energy-mode/m-p/1230681/highlight/true#M33814 I tried this and so far it works and has not lost its connection.

• Inspiron N5110 loses the wireless connection

  My Inspiron N5110 loses the wireless connection frequently. We have many other devices in the House - laptops, iPhones, etc. - who continue to operate perfectly through the router even when I lose my connection. The store usually brings me to reset the router, even if, as I have indicated, the router works properly. Any thoughts?  Thank you!

  Richard.Kelly,

  The Intel Centrino Wireless - N 1030 adapter works ONLY on 2.4 GHz

  How to connect to your wireless router I use these settings to the recommended wireless router I use channel 11. I have a new SSID to connect easier.

  You can also try these settings...

  Go to the drivers & downloads , enter your service tag, and then select your operating system. Under network, download and install the latest drivers.

  Try these tweaks...

  Start, Control Panel, Manager of devices. Click Network and then right click on your wireless network adapter, on the left, click on properties, power management. Uncheck the allow the computer to turn off this device to save power.

  Go to the options power and changed the wireless adapter setting, adjustment of maximum power for maximum performance.

  

  Rick

• When I disconnect the monitor Samsung, laptop monitor loses the office.

  I use a laptop Toshiba Satellite L645-S4102.  I have been using an external Samsung monitor for a while.  I need to use the laptop for a presentation only.

  I can change to the screen of the laptop or use the Samsung monitor and the laptop monitor as long as my computer is connected to the Samsung monitor.

  But, when I disconnect the monitor Samsung, laptop monitor loses the shortcuts on the desktop and the taskbar and shows only the background.  I tried to restart the computer, but the same thing happens.  As soon as I reconnect the Samsung screen, everything happens very well again.  Ideas please.

  Start with the extra monitor connected and used.  Then go to your desktop and follow the instructions below:

  1. Click background, choose the resolution of the screen.
  2. In the graph at the top, click on your laptop screen (if you don't know who is who, click "Identify" and click the monitor displays on the screen of the laptop).
  3. Check the box "use as primary monitor" and then apply the change.

  The bar of tasks and other items still show on the main monitor, so this will ensure that your laptop screen is considered to be the main.

  If necessary (unlikely but it could happen), repeat these 3 steps again when the additional monitor is disconnected.

• Satellite A80-128: pointer gel coming out of sleep mode

  I have persistent problems with gel pointer coming out of sleep mode. I have to reboot to get it working again. All this experience? (I also had two new hard drives mounted so far due to problems of pointer!)

  Hello

  Have you installed your device with the Toshiba Recovery CD?
  On this CD, you will find a Windows image with all the drivers, tools and patches.
  (Quickfix engineering) QFE patches East of patches from Microsoft you can also find on the Microsoft Web sites.

  But if you have installed the operating system with the Toshiba recovery image all have to factory with no problems.

• Dv6 7000: charging does that when the lid is closed (sleep mode)

  I have a laptop HP DV6 7000. The battery doesn't work that when the lid is closed (sleep mode).

  If I close the lid and plug in the charger, the light indicates orange and the battery will deliver to load almost full.

  If I open the lid before the orange light changing to white, battery icon always says: _ % available (plugged in, does not support).

  Several different Chargers give identical results. EACH of them is fully charge the battery in two hours; as long as the cover is closed. If I open the lid, even to say 50% load, the orange light glows white and the battery icon always says: _ % available (plugged in, does not support).

  Thank you, Ed.

  Hi @ElyMayor

  Thank you for your response.

  The last thing I can suggest to try a restore to factory.  Performing a recovery of system HP (Windows 7)

  While the recovery, there is an option to backup your personal files. If you have not already done so, it is now a good time.

  Restore files that have been supported to the top using HP Recovery Manager (Windows 7)

  Alternatively, you can contact HP support for assistance. They can access your system remotely to help alleviate the difficulties.

  Please contact our technical support at 800-474-6836. If you do not live in the United States / Canada region, please click on the link below to get a number of assistance for your region.

  World wide phone holder

• Recently started - can't get out of sleep mode

  XP SP3 - after PC switch mode 'sleep', cannot get out of sleep mode with mouse, keyboard, or by opening the cover on the top of the Tower - must press the power button.

  I checked the control panel / Dipslay and don't see any necessary adjustment automatically exit mode "Eve"

  Any suggestions on how to fix?

  Hello

  · What is the number and the model of the computer?

  · Do you remember all the recent changes on the computer before the show?

  Try the steps listed in the link below: how to solve the problems of hibernation and standby in Windows XP: http://support.microsoft.com/kb/907477

• Remote usb mouse freezes for bout 45 seconds after coming out of sleep mode

  Remote usb mouse freezes for bout 45 seconds after coming out of sleep mode

  Hi Aubrey,

  Step 1: Put the computer to boot and see if the problem still occurs

  Follow step 1 in the link below,

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  If everything works well after a clean boot, you can deduce that some third-party services are at the origin of the problem.

  Continue with the remaining steps to pin-point on the third party service.

  After find you the program that is causing the problem, you will have to perhaps to update or install a newer version of the program, if you rarely use that you should consider uninstalling the software.

  Important: n ' forget not the computer to start normal follow step 7 in the link.

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows 7 - new computer - changes in size of text coming out of sleep mode

  I have DPI set at 125% but when out of sleep mode, the screen goes to 150%, even if she is still set to 125% - so no reason, he goes back to the right size.

  Enjoy all the proposals/solutions.  Linda H.

  For anyone else having the problem; Open the Device Manager, graphics cards and update the drivers from the Chipset.  In addition, make sure you have the correct display resolution.  It worked!

• Continue to application play when the device goes into sleep mode

  Hey guys,.

  wondering if anyone knows how to maintain an active application when the unit goes into fashion watches?

  My application needs continue to work when the device goes into sleep mode if he went in that State by itself, or if the user put it to sleep.

  Yes I tried it on a physical device. It works, I promise you

  To clarify, here is what you will see when using KEEP_AWAKE:

  1 device shall not sleep when the application is currently active

  2. the device shall not sleep if the application is reduced, and you are in mode carousel

  3 device WILL sleep if the user switches to another application and full screen.

  In addition, another thing to know, if the unit is not assigned to the showcase mode, which is not by default, the audio stops when the user leaves your app. This is not related to sleep and is totally out of our control, but could be a good thing to add to your product details.

• How to get the computer out of safe mode of power

  How to get the computer out of safe mode of power

  Hello jeffg56,

  I understand that you want to leave safe mode, follow the steps below:

  Exit Safe Mode:

  1. Click Start, type msconfig in the search field and press ENTER to open the System Configuration window.

  2. On the general tab of the System Configuration window, select Normal startup, and then click OK.

  I hope this has been helpful, please let me know if you need more help.

  Thank you

• HP DV7t-6100 loses the wireless connection

  My HP DV7t regularly loses its wireless connection, without a valid reason, since I bought it a year ago. The remedy was to reset my router, despite the fact that no other devices at home - not even an another HP laptop and an HP printer - loses connection. But lately when I put the laptop to sleep - usually by closing the lid - the computer completely forget what network is attached to and so I have to reconnect manually each time. Even then, it takes very, very long time to connect and sometimes even said "it takes longer than expected to connect to the network.". Happy, told me what I already know! I checked all my settings in Windows 7 "Network and sharing Center" to make sure that my network is selected, it is a home network, that "automatically connect"; is selected, and that all my data password is correct. He still refuses to recognize the network and connect automatically. I'm done with this and just can't understand why this is happening. I haven't changed anything in my computer or router configuration, so I am at a loss why the system forgets everything and must be connected manually.  The wireless in my computer module is an Intel WiFi Link 1000 BGN and all drivers are up to date.

  None of the suggestions so far have worked, but it seems to me a solution: spend my router from WEP to WPA2 encryption seems to have solved the problem, at least for now. I have no idea why this works, but a bit of google searching seems to indicate that wireless WEP can be flaky with cards and routers. If it doesn't work anymore, I will be sure to repost for a solution. Thank you all for the help - it takes a village (so to speak).

  UPDATE: after 24 hours, the connection through WPA2 is rock stable with no connection dropped. It is also faster to download. I hope that this solution works for others.

• Satellite L350 loses the wireless connection

  Can someone please help?

  I have a Satellite L350-170 which perfectly connects to the internet using a cable to connect to my router.
  When you use the wireless to connect, I can only get a connection so I first of all turn off the wireless card and then enable it again, but I lose the connection within two minutes. I can reconnect if again, I turn off and then turn on the map.

  The OS is Vista Home Premium Service Pack 2, fully implemented to date. I have updated to the most recent available wireless network driver. I tried to turn off IP6.
  The laptop is connected to the network and receives a signal of power when it connects.
  When the connection is lost, no networks are detected, but properties card says card works Ok, although Ipconfig says media disconnected. Other mobile stay connected anywhere in the House.

  Thank you in anticipation of a quick solution.

  Where did you download the latest driver for the Realtek 802.11 g (RTL8187B) wireless network card?

  This is the WLan from Toshiba portal, where you can find the latest version of the driver:
  http://APS2.toshiba-tro.de/WLAN/

  I recommend also to renew the IP address if this problem would occur.
  Cmd execute command: ipconfig / renew
  This should help to assign the new ip address

  By the way: in the Device Manager-> Wlan card-> properties-> power management, you can uncheck the mark option which disables the card in order to save energy.

  Have you tested the WiFi with open (unsecured) WiFi connection?

• laptop loses connection w/web when sleep mode is activated.

  When my laptop goes to sleep, I get an error msg "windows cannot display Web page" when I wake up it. Troubleshooting problem is says cannot find a problem or "dns server is not responding. laptop usually functioning normally afterwards. Why my computer laptop do?

  Hello

  Thanks for posting your question in the Microsoft Community.

  I understand that this laptop loses the Internet connection in mode 'sleep'. Correct me if I'm wrong.

  I imagine the inconvenience that you are experiencing. I will try to help you in the matter of fixing.

  To help you suggest several steps to solve the problem, I would appreciate if you could answer the following questions:

   

  1. what operating system is installed on your computer?

  What version of the operating system Windows am I running? :

  http://Windows.Microsoft.com/en-us/Windows7/help/which-version-of-the-Windows-operating-system-am-i-running

  Please follow the methods and mark the question below:

  Method 1:

   

  Follow the steps in the link below.

   

  Network troubleshooting event logs to solve network problems:

  http://Windows.Microsoft.com/en-us/Windows7/use-Network-Troubleshooter-event-logs-to-solve-network-problems

  Method 2:

   

  Follow the steps in the link below.

   

   

  Network troubleshooting event logs to solve network problems:

  http://Windows.Microsoft.com/en-us/Windows7/use-Network-Troubleshooter-event-logs-to-solve-network-problems

   

   

  Your response is very important for us to ensure a proper resolution. Please get back to us with the information above to help you accordingly.

   

  In the future if you fall on any question relating to Windows, please do not hesitate to post your request here on Microsoft Community, we will be more than happy to help you.