LEDs of State fault/memory system UCS C200 M2

Similar Questions

• CISCO UCS C200 M2 amber display clear on mem and warning

  Hello

  My company bought 5 units of CISCO UCS C200 M2. The servers are equipped with 2 x 6 core 2.67 GHz. The server was also equipped with 32 GB of ram. One of the shows Server alert light yellow on mem and warning on the front panel. Can someone tell what could possibly cause this problem?

  Thank you

  Logan

  Hi Steve,.

  There could be a faulty MEMORY Strip on the system, in the MMIC, you can check the logs SALT (System event log) that will provide you with more details.

  I give advice you open a TAC case for this, we can take a look at the tech show and understand why accurate and if necessary replace the defective DIMM module / part (if defective).

  Thank you!

  . / Afonso

• My Apple Macbook late 2009 has been upgraded to 4 GB and Mountain Lion but runs very slowly. When I check the memory system activity monitor, I see that there are 1.6 GB inactive. Is this the cause of the slowness and what I can do?

  My Apple Macbook late 2009 has been upgraded to 4 GB and Mountain Lion but runs very slowly. When I check the memory system activity monitor, I see that there are 1.6 GB inactive. Is this the cause of the slowness and what I can do?

  Reinstall OS X from scratch and add more RAM.

  Ways to help make a slow Mac faster

  17 reasons why your Mac runs slower than expected

  Slow performance of Mac? This Article addresses!

  Difficulty of slow start in OS X | MacFixIt - CNET Reviews

  6 easy tips to speed up OS X Yosemite on your Mac.

  Avoid using third-party software that claims to clean your computer. This software does more harm than good. In addition, you don't need it. Note that all computers become slower over time even in the normal conditions of use. Generally, the experienced users erasing the hard drive and do a clean install from scratch at least once a year or every time that the installation of a major upgrade of the OS. Well sure doing so also means that you need to maintain regular and several backups.

  Add more RAM or reduce the number of simultaneously executed from applications and utilities. Remove unnecessary software such as anti-malware and that promises to clean your Mac. Look for the runaway process: Runaway applications can shorten the battery life, affect performance and increase the heat and fan acti... See also:

  Before Mavericks

  Open the activity monitor in the Utilities folder.  Select all processes in the drop process .  Click the % CPU column heading twice to display in descending order.  If find you a process that uses a large amount of time processor (> = 70,) then select the process, and then click the quit icon in the toolbar.  Click the force quit button to kill the process.  See if that helps.  Don't forget to mention the name of the runaway process, so you can find the cause of the problem.

  Mavericks and later versions

  Open the activity monitor in the Utilities folder.  Select all processes in the menu display .  Click the CPU tab in the toolbar. Click the % CPU column heading twice to display in descending order.  If you find a process that uses a large amount of CPU %, then select the process, then click on the quit icon in the toolbar.  Click the force quit button to kill the process.  See if that helps.  Don't forget to mention the name of the runaway process, so you can find the cause of the problem.

  Things you can do to solve the slow Downs

  If your computer seems to run slower, here are some things you can do:

  Start with tours: OS X maintenance - MacAttorney;

  The X Lab: the X-frequently asked questions.

  " Safe mac" Mac Performance Guide;

  " Safe mac" the myth of the dirty Mac;

  Maintenance fast Mac Help.

  Start in Safe Mode , and then repair your hard disk and permissions:

  Fix the hard disk and permissions before Lion

  Boot from your OS X install disk. After the installer loads, choose your language and click on the button continue. When the menu bar appears select utility drive in the Utilities menu. After that the charges of THE select your entry from hard drive (mfgr. ID and car size) in the list on the left.  In the status area, you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is faulty or has failed. (State SMART is not reported on external drives Firewire or USB). If the drive is "verified", then select your OS X volume in the list on the left (subentries under the entry for the road), click the first aid tab, then click the repair disk button. If THE reports any errors that have been corrected, and then run repair disk again until no errors are reported. If no errors are reported, click repair permissions. Wait until the operation is complete, then exit FROM and return to the installer.

  Repair the hard drive - Lion-Lion/mountain/Mavericks

  HD recovery start:

  Restart the computer and after the buzzer, press on and hold down the COMMAND and R until it appears the screen of Menu utilities. Otherwise, restart the computer and after the buzzer, press on and hold down the OPTION key until the Boot Manager screen. Select recovery HD disk icon and click on the button below.

  When the recovery menu appears, select disk utility. After that the charges of THE select your entry from hard drive (mfgr. ID and car size) in the list on the left.  In the status area, you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is faulty or has failed. (State SMART is not reported on external drives Firewire or USB). If the drive is "verified", then select your OS X volume in the list on the left (subentries under the entry for the road), click the first aid tab, then click the repair disk button. If THE reports any errors that have been corrected, and then run repair disk again until no errors are reported. If no error is not reported, then click repair permissions. Wait until the operation is complete, then exit FROM and return to the main menu. Select restart from the Apple menu.

  Restart your computer normally and see if it helped at all. Then do little maintenance:

  For disk utility can't handle situations, the best third party is Disk Warriorutility;  Fixed DW only for problems with the disk directory, but most disk problems are caused by the corruption of directory; Warrior drive 4.x is now compatible with Intel Mac.

  Note: Alsoft ships DW on a bootable DVD that will boot Mac running Snow Leopard or earlier. He cannot start Mac that came with Lion or later preinstalled, however, DW will work on these models.

  Suggestions for OS X maintenance

  OS X performs certain maintenance functions that are supposed to take place on a daily, weekly, or monthly period. Maintenance scripts that are run at the beginning AM only if the computer is turned on 24/7 (no sleep). If this isn't the case, then a great solution is to download and install a shareware like Macaroni, JAW PseudoAnacronor Anacron utility that will automate the maintenance regardless of whether activity if the computer is off or asleep.  Dependence on third-party utilities to run periodic maintenance scripts has been significantly reduced since Tiger.  These utilities have little or no functionality with Snow Leopard or later version, and must not be installed.

  OS X automatically defrags files smaller than 20 MB in size, so unless you have a disk full of very large files it little need to defragment the hard drive.

  Under no circumstances should you install operating MacPaw or ZeoBit software (CleanMyMac/CleanMyDrive or Mac Keeper, respectively.) You don't need special software to keep your computer.

  Useful links about malware Protection

  "If you have an immediate problem with ads popping up see the Mac without danger" Adware removal Guide and AdwareMedic.

  Open Safari, select Preferences from the Safari menu. Click the Extensions icon in the toolbar. Disable all Extensions. If it stops your problem, then re-enable one by one until the problem returns. Now remove this extension as it is the origin of the problem.

  The following comes from user stevejobsfan0123. I made minor changes to adapt to this presentation.

  Difficulty a few pop ups browser that supported Safari

  Common pop - ups include a message saying that the Government has taken over your computer and you pay release (often called "Moneypak"), or a false message saying that your computer has been infected and you need to call a number of tech support (sometimes claiming to be Apple) to get it to be resolved. First of all, understand that these pop-ups are not caused by a virus and that your computer has not been assigned. This "hack" is limited to your web browser. Also understand that these messages are scams, so don't pay not money, call number, or provide personal information. This article will give an overview of the solution to remove the pop-up window.

  Quit Safari

  Usually, these pop-ups will not go by clicking 'OK' or 'Cancel '. In addition, several menus in the menu bar may become disabled and show in grey, including the option to leave Safari. You'll probably force quit Safari. To do this, press command + option + ESC, select Safari, press on force quit.

  Relaunch Safari

  If you restart Safari, the page will reopen. To avoid this, hold the "Shift" key when opening Safari. This will prevent windows since the last time that Safari was running since the reopening.

  It will not work in all cases. The SHIFT key must be maintained at the right time, and in some cases, even if done correctly, the window is displayed again. In these circumstances, after force quit Safari, turn off Wi - Fi or disconnect Ethernet, depending on how you connect to the Internet. Then restart Safari normally. He'll try to reload the malicious Web page, but without a connection, it will not be able to. Leave this page by entering a different URL, i.e. www.apple.com and try to load it. Now you can reconnect to the Internet and the page that you entered is displayed rather than the malicious.

  An excellent link to read is Tom Reed Mac Guide of malicious programs.

  Also, visit the FAQ XLab and read of detection and avoid malicious software and spyware.

  Check out these articles from Apple:

  Mac OS X Snow Leopard and malware detection

  OS X Lion-Protect your Mac against malicious software

  OS X Lion mountain - protect your Mac against malicious software

  OS X Mavericks-Protect your Mac against malicious software

  On the quarantine of file under OS X

  If you need antivirus protection Thomas Reed recommends to use ClamXAV. (Thanks to Thomas Reed to this recommendation.)

  The user Joe Bailey comes this equally useful advice:

  The facts are:

  1. There is no anti-malware software can detect 100% of malware out there.

  2. There is no anti-malware that can detect all targeting the Mac.

  3. the best way to prevent breaches the most is for you as the user is aware that

  the most successful malware attacks rely on sophisticated social engineering

  techniques preying on human greed, * and fear.

  4 Internet pop-up windows telling the FBI, NSA, Microsoft, your ISP has detected malware on

  your computer is designed to trick you into installing their malware thinking it's a

  protection against malware.

  5. some of the anti-malware market products are worse than malware

  go where they are supposed to protect you.

  6. be careful where you go on the internet.

  7. don't download anything from sites, you know are safe.

  8 avoid links that you receive in email, always be wary, even if you get something

  you think a friend is, but that you did not expect.

  9. If there is any question in your mind, then assume that it is malware.

  Troubleshooting Applications

  I recommend that you download a utility such as TinkerTool System, OnyX, Mavericks Cache Cleaneror hiding a Cocktail that you can use to delete the former newspapers and archives, cleaning, etc. Corrupted cache, logs or temporary files can slow down the application or OS X crashes and panics of the kernel.

  If you have leopard snow or leopard, then for similar repairs install Applejackfreeware utility.  If you do not start in OS X, you can boot into single-user mode , where you can run Applejack to make a set of routines for repair and maintenance of the command line.  Note that it takes 1.5 AppleJack for Leopard. AppleJack 1.6 is compatible with Snow Leopard. Applejack does not work with Lion and later versions.

  Basic backup

  For some people, Time Machine will be more than enough. Time Machine is part of Mac OS X. There are two components:

  1. a panel of Time Machine preferences as part of the system of preferences;

  2. a request for Time Machine, located in the Applications folder. It's

  used to manage backups and restore backups. Time Machine

  requires a backup drive that is at least twice the capacity of the

  drive being backed up.

  You can also get an external drive at least equal to the size hard disk internal and make (and maintain) a bootable clone/backup. You can make a bootable clone using the disk utility's restore option. You can also create and maintain clones with good backup software. My personal recommendations are (the order is not significant):

  1 Carbon Copy clone

  2. get backup

  3 already seen

  4 superDuper!

  5. Synk Pro

  6. Tri-Backup

  Visit The FAQ XLab and read the FAQ on the backup and restore.  Also read How to back up and restore your files. For using Time Machine, visit FAQ Time Machine of Pondini for help with all this time Machine.

  Referenced software can be found at MacUpdate .

  Additional tips

  Make sure you have a sufficient amount of RAM installed for the number of applications you run simultaneously. Make sure to leave a minimum of 10% of the capacity of the hard disk as free space.

  Add more RAM. If your computer less than 2 GB of RAM and you use OS X Leopard or later, then you can do it with more RAM. Snow Leopard and Lion works much better with 4 GB of RAM that is their system. Most concurrent applications, that you tend to use the more RAM you should have.

  Always have at least 15 GB, or 10% of the capacity of your hard disk as free space, the largest. OS X frequently accesses your hard disk, so offering enough free space will keep things slow down.

  Check for applications that may be hogging the CPU:

  Before Mavericks

  Open the activity monitor in the Utilities folder.  Select all processes in the drop process .  Click the % CPU column heading twice to display in descending order.  If find you a process that uses a large amount of time processor (> = 70,) then select the process, and then click the quit icon in the toolbar.  Click the force quit button to kill the process.  See if that helps.  Don't forget to mention the name of the runaway process, so you can find the cause of the problem.

  Mavericks and later versions

  Open the activity monitor in the Utilities folder.  Select all processes in the menu display .  Click the CPU tab in the toolbar. Click the % CPU column heading twice to display in descending order.  If find you a process that uses a large amount of time processor (> = 70,) then select the process, and then click the quit icon in the toolbar.  Click the force quit button to kill the process.  See if that helps.  Don't forget to mention the name of the runaway process, so you can find the cause of the problem.

  This problem occurs often because of a corrupted cache or the preferences file or an attempt to write in a corrupted log file.

• MMIC UCS C200 M2 blade - cannot access

  Hi all

  I was hoping someone in this forum could help with a problem I have on a customer site. We have therefore two blades UCS C200 M2 we cannot access MMIC of. When I try to reach the IP address, the browser just sits there, but the IP address is an echo request ICMP who responded. I rebooted a systems press F2 and tried to launch the utility BIOS Setup MMIC but received a message "no attention not found" and the only option was to hit very well.

  What would cause this? And should I update the firmware? If I need to update the firmware how can I go about this...?

  In addition, these systems are running ESXi 4.1, but I believe that the version of VMware is not compatible. Could someone help me confirm this?

  Any help is greatly appreciated!

  -Bobby

  Hello

  It worked before?

  If this is not the case, try resetting the MMIC or it could be a browser/java problem too. The problem exists across the browser and several pc user.

  See doc below to configure the Mmic

  http://www.Cisco.com/c/en/us/support/docs/servers-unified-computing/UCS-...

  http://www.Cisco.com/c/en/us/TD/docs/unified_computing/UCS/c/SW/CLI/CONF...

  -
  Siva

• Replacing hard drive RAID 10 (UCS-C200-M2)

  Guys,

  I'm running RAID10 on UCS C200 M2 and exchanged one of the defective drive.

  Currently, there is beep for more than 12 hours and I guess that the new drive is under reconstruction at the moment.

  In addition, physical drive status is currently on "not well configured" on CIMC. The status changes to "online" after

  the reconstruction end? Will be required reboot when the rebuild is complete?

  Please advice.

  Hello

  If the State of the reader to not configured well. You will need access to the Webbios to change online status and allow reconstruction to be undertaken.

  You will find here all the information required to set the drive to the State once again

  http://www.Cisco.com/c/en/us/TD/docs/unified_computing/UCS/c/SW/RAID/con...

  If by chance you encounter any problem do such thing. Call the TAC and they will help out you with it.

  Please note ALL useful answers

• Is it possible to reallocate the memory system on a Satellite L500 - 19 X?

  I was curious why my Satellite L500-19 X has not run games very well when I had almost 1.8 GB of memory, then I noticed that only 128 MB of it was used for the games, is it possible that I can pull some of the system memory that is shared over dedicated games?

  I know, you cannot reallocate memory system yourself, the system does this automatically. You can do it in the Bios settings if the share option is available.

• Out of memory system on environment 2011 27 "imacz

  Yesterday began to receive messages from memory system on a regular basis.

  I haven't added any new application for almost a year and have not been broadcast nothing more than safari (with only 1 or 2 windows open), mail, adobe pro, calendar, contacts.

  I ran the activity monitor, and under memory pressure, I see that Safari is open, the pressure will increase to nearly max (15,49 GB) with no other apps to open.

  I think that this could be related safari, but have no idea how to fix this. Help.

  OS X Yosemite 10.10.5, 3.4 GHz Intel Core 17, Mem = 16GB 1333 MHz DDR3, AMD Radeon HD 6970M to 1024 MB

  I started to write this on the Mac and had to finish on my iPad, because in the time it took to write the 1st by the Dopers memory pressure and use of safari went beach ball

  Please quit and then restart Safari after taking each of the steps that you have not already tried. Stop when the problem is resolved.

  Back up all data before making any changes.

  Step 1

  The problem may be caused by web pages in the list of the favorite who sometimes or always request access with a CAPTCHA. If you know that there are these pages among your Favorites, remove them and see if there is an improvement. If not favorite and remove all Favorites, then restore them one or a few at a time until you find the culprits. There may be more than one.

  Credit for this observation to ASC member ethereum.

  Step 2

  Triple-click anywhere in the line below on this page to select this option:

  ~/Library/Safari

  A right click or Ctrl-click on the line and select

  Services ▹ Open

  the contextual menu.* should open a folder named "Safari". Quit Safari runs. One or more files in the open file must have a name starting in 'history '. Move these files and only those which, on the desktop, leaving the window open. Restart the application and test. If there is no change, leave again and put the files that you moved back where they were, crushing those who could be created in their place. If not, remove the files that you moved. The browser history will be empty. If possible, restore deleted files from a previous backup problem.

  * If you do not see the item context menu copy the selected text in the Clipboard by pressing Control-C key combination. In the Finder, select

  Go ▹ go to the folder...

  from the menu bar and paste it into the box that opens by pressing command + V. You won't see what you pasted a newline being included. Press return.

  Step 3

  Open the iCloud preferences window and uncheck the box marked Safari only. Test. Then check again, if you wish.

• cannot open a session on the computer saying low memory system

  I got a blue screen coming up on top of my computer, after much frustration, I rebooted my windows xp. Everything worked very well but I couldn't load all my drivers including my driver to pick up Internet. I was just trying to download updates for the drivers with the yellow mark. that was about four of them. the next time I turn on my computer, it says logon, but there is no longer any newspaper in the names to the screen. So I can't pm any more away. I can't start in safe mode, and no matter if I load frm hard drive or a cd without the cd that happens even tho the loggin with no connection name page.  Sometimes, a message indicates low memory system. but it worked very well. When the message memory system is in place, it says something like windows increases the size of the paging file virtual memory. For more information, press help. but I can not connect to get help. and before that I could easily connect in safe mode now it comes to the main login page. I'm so frustrated. If you could help I would be very grateful

  Linda

  Hello

  Use the last known good Configuration tool to restore the operation of Windows XP

  If Windows does not start, try to restore operation of Windows XP by using the last known good configuration. To do this, follow these steps:

  a. start the computer and press the key F8 when Windows begins to start. The Windows Advanced Options menu is displayed.

  b. use the ARROW keys to select last known good Configuration (your most recent settings that worked), and then click OK.

  c. If a boot menu appears, use the ARROW keys to select Microsoft Windows XP, and then click OK

  Windows XP starts your computer by using the registry information that were recorded at the close of the last.

  See also: http://support.microsoft.com/kb/308041

• When I click on dump debugging, system, thumbnails and files dump files memory system archive of windows error reporting

  When I click on dump debugging, system, thumbnails and files dump files memory system archive of windows error reporting
  They does not clear my cleaning disc on my computer at home. If someone could help
  deal with this problem?

  * original title - disc clean up problem *.

  You are welcome.

• UCS C200 RAID solution

  Hello

  I hope for your help about the technical question about the RAID.

  We bought a server in a rack of Cisco UCS C200. Now I looking for information on the best RAID solution in our case.

  The question:

  As I understand it, there is an integrated RAID solution: Intel ICH10R in UCS C200 server. We use this RAID configuration now and it works OK. However, we wonder if it is worth installing the PCIe controller (we have HP Smart Array P410 (ATA/dis2) card). We use currently 4 SATA and RAID drives works as expected, but we are interested in, if there are all the advantages of the separate RAID controller card. Above all, we are interested of performance benefits as we plan to have a lot of disk writes (records call - about 10-20 calls per hour, lasting 2 minutes on average). We would be happy to stay with RAID integrated if it works stable. On the other hand, we will install the above mentioned Intel RAID card if you say that it would be the best solution about the reliability and wear of the disc.

  I would be grateful for any comments.

  Kind regards

  Vytas

  Vytas,

  Your question is probably down to RAID levels supported for each card.  The performance of each should be relavitley the same, so I would not concentrate on that.

  The only supported RAID controllers are listed here and must be purchased from Cisco:

  http://www.Cisco.com/en/us/docs/unified_computing/UCS/c/HW/C200M1/install/RAID.html#wp1015625

  "Others' work, but you'd be yourself if you encountered problems with TAC.

  The integrated Intel ICH10R card supports up to four SATA using RAID0 (striped) or RAID1 (mirror) drives.

  If you need one RAID5, 10 or more, then you must a MegaRAID controller to do.

  All RAID controllers provided by Cisco are heavily on trial and could be your best option for reliability and performance.

  Kind regards

  Robert

• UCS C200 and NIC Teaming/FailOver

  As UCS C200 with management of a 10/100 and 10/100/two interface 1000 interfaces and PCIe with 4NIC

  I want to install CUCM 8.5 is the NIC Teaming/failover supported by UCS C200 and how to set up the NIC Managment interface with failover?

  Thank you.

  Hello

  As you install apps from the CPU on the server of the UCS, speech application team listed their recommendations here.

  http://docwiki.Cisco.com/wiki/QoS_Design_Considerations_for_Virtual_UC_with_UCS#Guidelines_for_Physical_LAN_Links.2C_Trunking_and_Traffic_Sizing

  You can create a NIC teaming in the ESXi via vSphere client software for traffic from from / destined for virtual machines.

  For C200, we have only one management port and if you use the management for MMIC traffic port, switch option is not available.

  However, if you choose to use host for MMIC traffic NETWORK ports, you can set up CIMC NIC mode for 'LOM shared' which provides the NIC teaming options.

  http://www.Cisco.com/en/us/docs/unified_computing/UCS/c/SW/GUI/config/Guide/1.4.1/b_Cisco_UCS_C-Series_GUI_Configuration_Guide_141_chapter_01000.html#concept_AC4EC4E9FA3F4536A26BAD49734F23D0

  HTH

  Padma

• UCS C200 M2 R200 - 1120402W Nic will negotiate only 100 MB full

  We have a new UCS C200 M2 server running ESXi 5.0.0 and will be only neg a speed of 100 MB - tried to connect a GLC - T on a 3750 and also Port copper on 2960G - same result.

  Trying hard value speed 1000 in vSphere client produced an error:

  Call 'HostNetworkSystem.UpdatePhysicalNicLinkSpeed' to object 'networkSystem"on ESXi '172.19.99.103' failed.

  Operation failed, the diagnostic report: forcing 1000Mbps or faster may not be supported on this network device, please use autonegotiation call 'HostNetworkSystem.UpdatePhysicalNicLinkSpeed' to object 'networkSystem"on ESXi '172.19.99.103' failed.
  Operation failed, the diagnostic report: forcing 1000Mbps or faster may not be supported on this network device, use rather auto-negotiation

  Adapter is Intel 82576 Gigabit Network Connection

  Just use HUU to version 1.4 - no improvement.

  Thoughts, suggestions?

  Gordon,

  Can you please share the output of following ESXi

  VMware - v

  esxcfg-NICS - l

  ethool-i vmincX

  Do you see the same behavior with the other ports of the NETWORK adapter on the server?

  Padma

• UCS C200 Server Power Supply Question

  We make some changes in our data center and which involves electric grid.  We had to replace our Dustribution of power rack and to respond to the charge, we moved 208V, 3 phase power distribution.  Read the literature, I see that the power supply to the UCS C200 servers can operate 115V to 230V AC.

  My questions are: is it everything I have on power supply from 120V AC 208 v power supply power supply power supply?  Can I have a power running at 120 v and the other operating at 208V?  I try to avoid the closure of the server.

  According to specifications

  http://www.Cisco.com/c/dam/en/us/products/collateral/servers-unified-com...

  Table 41 UCS C220 M3 SFF 450w Power Supply Specificationspescription
  Input AC voltage
  90 to 264 VAC auto-ranging,
  100 to 120 VAC nominal
  200 to 240 VAC nominal

• UCS C200 M2 could not start

  Hi all

  My Cisco UCS C200 could not start. Once checked, I found that the problem is the raid controller, the card may not work properly.

  the type of raid used controller is LSI MegaRAID 9260-4i

  can I replace this controller card with different types such as LSI MegaRAID 9260-8i

  If can, what should I do? are there concerns?

  Thank you for your kindness

  That should be fine.  See the documentation of the TA on the exact process of swapping the controller, but since they are of the same generation, just different port internal account (4 vs 8) and all RAID information is stored on the discs themselves, you should have no problem exchange controllers and imports of table on the new controller.  Once swap you controllers, host of startup, enter the optional ROM of LSI and check if the table is waiting for import (if she is not the automatic import).

  Kind regards

  Robert

• vmrun start leads to a "error: operation failed because of the current state of the system.

  Hello

  I am running the vmrun like this on the console command.

  / usr/bin/vmrun t CR h https://ourhost/sdk u ouruser Pei ourpwd start ' build001/build001.vmx [datastorename] '.

  I get the error text:

  Error: The operation has failed because of the current state of the system
  

  When I opened the Vsphere client, I see that the operation began, but also with an error: the operation is not allowed in the current state.

  I'm running on VMWare Vsphere Server Version 4.1.0 Build 258902

  How can I make sure via command line that the State of the system is correct. Is there a way to get corrected through an order status?

  When I try to power to the top of the image within the user interface, it works, but I need to know the opposite effect.

  Thank you.

  Hello and welcome to the forums.

  check via the State of the line of command of this virtual machine if necessary, unblock the process using vmsuport x how to show in this http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1004340 Ko