Line and microphone input

Similar Questions

• complete meter but no sound on the line and microphone Vista 64-bit

  Good afternoon. I'm so tired of having to buy expensive USB audio devices to get anything to work on this PC. I have HP Pavilion with Vista Home Premium and core quad processor.  What is happening, it's the bars in the meter go all the way to the top as if there is an incoming audio signal but no sound goes in. I've updated my drivers and still nothing. Hellppp! Any ideas, please let me know.

  Hello

  I would suggest trying the following steps and check:

  a. Click Start, open Control Panel.

  b. click sounds, click the recording tab.

  c. click microphone, and then click Properties.

  d. under the controller information, check if the correct sound card is selected.

  e. click on the advance tab, under exclusive mode uncheck both boxes.

  f. click on apply, then ok.

  Check if it helps.

  It will be useful.

• Ventrilo and Microphone does not.

  Cannot enable DirectSound for the selected device.
  DirectSoundCaptureCreate failed. HR = DSERR_NODRIVER. No sound driver is available for use

  That's what I get when I open Ventrilo. Any suggestions on where to find the driver, I need to get this working?

  Hello Reetz,

  Thank you for writing to Microsoft Vista Community Forums.

  1. ensure that your audio drivers are correctly installed and up-to-date.
  2. in some cases, the drivers are properly installed and the error persists, open teamspeak, go into the settings menu and open the 'Options '.
  3. in the "Sound Devices" tab, change the audio of 'Wave' driver if it was set to 'Direct3dSound' and change to "Direct3dSound" if it has been set to 'Wave' and then press 'Ok '. Close teamspeak and reopen it.

  You can also browse the links for more information on ventrilo and try to contact them if the problem persists.
  http://www.Ventrilo.com/FAQ.php
  http://www.Ventrilo.com/about.php
  http://www.Ventrilo.com/dlprod.php?id=1

  Also, follow the steps below to check if the Microphone is properly configured and enabled in Vista.

  Step 1: Test of an audio signal
  1. click on start, then Control Panel.
  2. click on hardware and sound and then click on manage audio devices...
  3. click on the recording tab.
  4. to test the microphone, speak into it. To test the line, send a signal to the line at the port of devices audio source (press play on the audio player). Look at the gray bars next to the name of the device under the recording tab:
  * If the gray bars next to the device name turns green, this device is active and an audio signal is passed through the microphone or line-in port. This step shows that this problem is related to sound parameters in the software that uses the microphone. If you have not already done so, set the device selected by default and adjust levels. Once the device is set by default and levels are defined, use and adjust the sound recording or voice carrying software.
  * If the gray bars remain inactive and grey, the device does not have a signal. Leave the record open tab and go to the next step.

  Step 2: Check the volume levels and mute
  The volume of the speaker to the microphone and line - in may be activated or rejected. Use the following steps to check the volume of speaker for line and microphone levels.
  1. click on start and then click Control Panel.
  2. click on hardware and sound.
  3. click on sound.
  4. Select speakers, and then click Properties.
  5. click on the levels tab.
  6. click the button mute Microphone and on any other line that is cut.
  7. use the slider to increase the micro level and each line at least 75.
  8. click on OK.

  Step 3: Update the audio drivers
  You can see a front-end port microphone does not work, a recording device is missing in the recording tab, a microphone is not recognized when it is plugged in, or any other problem. There may be updates audio drivers that can solve this kind of problem. Use the following steps to ensure that the audio drivers are up to date.
  1. connect to the Internet.
  2. click on start and enter the Device Manager in the start search field.
  3. click on the plus sign next to sound, video and game controllers.
  4. right click on the name of the sound material and select software update of the driver...
  5. click on search automatically for a driver updated and wait for Windows to update the driver software.
  6 Windows checks a remote Web site to see if the update of the driver software is available.
  * If an update is available, let Windows install the update.
  * If an update is not available, proceed to the next step.
  7. once the update is successfully installed, test the microphone or line like that was made in step 1. If the problem persists, proceed to the next step.

  Step 4: Configuration of Windows registry settings
  By default, Windows Vista automatically activates microphones and line-in ports. Use the following steps to set the microphone/line-in port to be the default port and configure the logging levels.
  1. If the recording in the Audio window tab is not selected, open the sound and click the recording tab and make sure the State is defined as below.
  a - port micro - work and set as default
  b - line In - work
  c - Digital (S/PDIF port) In - work
  d stereo Mix (mixer software) - disabled
  2. If several microphones or line - in ports are available, select the port you want to use. Click on set as default to make this device default audio input device.
  3. If the device you want to use contains a small circle with an arrow pointing down, the device is disabled. To activate the device, right-click the device name, and then select activate.
  4. with the selected device, click Properties, and then click the levels tab.
  5. adjust the slider up to 75% of its range.
  6. If the mute is enabled, click the button mute to reactivate the device. The mute button should show as a blue speaker without any red circle.
  7. If the Microphone Boost is available, adjust and + 20.0 dB.
  8. click OK to make the changes.
  9. test the microphone as was done in step 1 to determine if Windows is able to detect a signal from the microphone or line used. If you have completed all the steps and the microphone or the source device still does not work, the audio ports or the computer's sound hardware can be bad.

  If the problem persists, contact us return with details below?
  1 microphone working on the computer at any time earlier?
  2. Since when are you facing the issue?
  3. don't you make changes to the computer until this problem occurred?
  4. the version of Ventrilo you use on your computer.

  It will be useful.

  Thank you and best regards,

  Srinivas
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• program speech recognition on Windows 7 and Vista sense microphone input

  One of my friends tries to use the text-to-speech program built into Windows 7 and Vista, on their computer and laptop computer - with a brand new microphone and using a USB plugin and an audio input jack. All we ever get is a if you asking the window of our "MIC is muted.

  We need this thing to work. And please don't tell us 'optimize our browser '. We don't need this kind of nonsense lazy, evasive. We want to know why this specific programme will not work. Thank you.

  One of my friends tries to use the text-to-speech program built into Windows 7 and Vista, on their computer and laptop computer - with a brand new microphone and using a USB plugin and an audio input jack. All we ever get is a if you asking the window of our "MIC is muted..."

  Connect the USB microphone (to aft port on a desktop computer, any port for laptop). Then right click on speaker icon lower right task bar. Click recording devices. Highlight the USB microphone. Speak into the microphone. Green bars should move up and down like you're talking about. If they do not, click Properties and then the levels tab level slider move to 100%, click OK and test speaking into the microphone again to see if green bars go up and down. If they don't, try a different USB port.

  For the analog microphone test the same way. Use a Mic back in port, not one alone on the front or on a monitor.

  Microphone work, go into Control Panel, speech recognition, and microphone Set prior to the formation of WSR (Windows speech recognition).

  Markoe Marty

• Never used front microphone input, correct Recorder window, no audio output.

  Sound input tape recorder going nowhere, an acoustic window is supposed to open, it does not work.

  There is a software that is missing in my computer portable pavilion g7.  Its media player is fine, its internet

  is fine, don't you miss that sound comes from the microphone input.  The sound recorder window is open and the

  record bar is moving because the entry varies, how do I get the sound to the speakers.  Never used this

  the option before, it might be defective from the factory.

  Problem solved.  You can not turn on computer with the microphone or other audio cable.

  If the computer does not meet the entries, you must connect the microphone or audio

  cable after connection and then a window will open allowing you to select the default entry.

• Equium L20-197: what is the maximum impedance for microphone input

  Can someone tell me what the maximum impedance is for the microphone to an Equium L20-197 standard input

  I'm doing some recording on my laptop through the microphone input. I would like to know the maximum impedance entry is for Conexant AC-Link Audio version 6.14.10.590.
  I do records and try different input methods, but I'm afraid to blow the whole sound card and the motherboard.

  I looked everywhere and I can't find out. If someone could help me please let me know.

  Unfortunately, I also goggled and checked some sources of information but nothing
  Did you ask to the authorized service provider in your country for advice or details?
  Technicians usually have access to maintenance manuals that might provide details
  Should more known as users just like you and me...

• Digital and analog inputs simultaneously - NI USB-6009 and NI USB-6212 - ANSI C

  Hello

  I'm reading at all times and at the same time analog and digital inputs. Digital and analog samples must be sampled at the same clock and acquisition should be started (triggered?) at the same time (I don't want, after some time, analog reception more digital samples - the opposite is also true).

  I found an example (in C source code) "National Instruments\NI-DAQ\Examples\DAQmx ANSI C\Synchronization\Multi-Function\ContAI-Read dig Chan" and tried to run with two USB cards: NI USB-6009 and NI USB-6212. Unfortunately, the two results by mistake, as described below:

  DAQmx error: the requested value is not supported for this property value.
  Property: DAQmx_SampTimingType
  You asked: DAQmx_Val_SampClk
  You can select: DAQmx_Val_OnDemand

  Task name: _unnamedTask<1>

  State code:-200077
  End of the program, press the Enter key to exit

  -Is it possible sync analog and digital acquisition in the paintings?

  -If so, how?

  Thank you

  Hello tcbusatta,

  Two of these modules, USB = 6008 and USB-6212, support only timed software inputs and digital outputs.  This means that you cannot define material timing (like finished sampling or continuous) for these modules.  Digital lines can be retrieved or written once to each call DAQmx read.

  This means that you will not be able to get any type of synchronization tight between the analogue and digital channels.  You will need a Board such as the NI USB-6341 in order to synchronize the AI and DI closely.

• Line and force

  I want to do a VI that will show me how many random numbers from 0 to 100 range must be generated. After that VI needs to draw a histogram showing how much % of the numbers was 0-49 range and how much between 50 and 99. There was also two digital indicators showing how many numbers is both of these ranges.

  I use ' line and force ", but for example if I generate numbers: 78, 97,74;

  ' First ' line and force "(50-99)" will show the output: 78, 97,74, which is correct.

  "But second" line and force "(0-49)" will show the output 49,49,49 that I don't want. I just want to show in this example a zero.

  After that I'll connect both inputs of histogram, will be OK?

  See photo, thank you

  
  

• 6009 outputs digital and analog input synchronization

  Hello

  I work in a program NI 6009. I want to leds by car with outputs digital NI 6009. For example, leads first will be on until what 200 micro seconds then second led will be on up to 200 micro seconds, and then first of all led will be on up to 200 micro seconds. I'll take led with photodedector signals and connect analog output photodedector input NI 6009. I want to synchronize the outputs digital and analog input and separate the first and second led signals the analog input for NI 6009 channel. How can you do with NI 6009? Please ADV

  You can not do with the USB-6009 case. Its outputs digital are software with a maximum speed of slightly more than 100 samples per second. The outputs can produce 200 microsecond pulses and cannot be synchronized with the analog input.

  You need a device with outputs digital hardware timed or counters that can produce a pulse outputs.

  You can synchronize a bit digital output and analog input recording signal on an additional channel to HAVE. Will allow you to see the photodetector and LED the drive with the same schedule and such resolution as described by the sampling rate I. The maximum sampling frequency of AI on the USB-6009 case is 48 kHz that is shared by all channels. If you have two lights to led and photodetector two signals maximum sampling rate would be 48 kHz/4 = 6 kHz which is barely fast enough for your 200 US signals. For more than 4 channels, it won't be fast enough.

  I suggest a simple oscillator circuit building and use it to clock a flip flop. This will give you alternating signals to drive the LEDs. You can use a line to reset the flip flop to give you control without the need for high speed.

  Lynn

• In c#, how set digital Ports lines outputs or inputs

  Can a port contains the input and output lines at the same time?

  Hello

  The 6221 is a map of the M series for you can configure each individual line as an input or output so you might have a release for your control, then as an input signal as you suggest.

  Kind regards

• Acer Aspire v3 - 571 g audio and microphone jack

  What type of jack audio and microphone is on the acer aspire v3 - 571 g? I would like to buy a headset that needs an audio PLUG to 4 pin + jack mic combined (iPhone/Samsung headsets with microphone) and I was wondering if my laptop was there.

  Your laptop has standard audio input/output jacks. 3.5 mm plug. Absolutely, you can buy the kit microphone and headphones, but you will need an adapter that allows to use the headphone jack and microphone jack separately on your device.

• What are the permissions of camera and microphone?

  30.0 Firefox.
  I am not referring to a tablet or phone app - I use my laptop.

  Because these permissions are on the Info Page of the sites, what reason would they (any site) need permissions for microphone or camera? I'm in maintaining private as much as possible.
  Along the same vein, I was playing with authorities and had no idea that I could actually blocked my location.
  It's great.

  Thank you.

  You must grant permission to leave the Web sites to access the camera and microphone.

• Printer skips lines and enlarged fonts between pages based on the web.

  bold text Range of printers HP c7200 connected wireless to MacBookPro w/Lion. Using the browser Firefox to version 9.0.1. Printer prints the first page very well, then the second page starts by skipping several lines and large print. PC connected to the same printer, and printer works OK. Safari works OK, too. Solutions would be appreciated.

  Problem started before the upgrade to Mac Lion. Lion updated printer driver. The same problem. Only happens when I try to print a web page or something downloaded from a web page, like a financial spreadsheet. Non-Web-based print OK. Help. Thank you.

  I saw this happen when the Page layout on FireFox browser has been set to 80% (or probably anything less than 100%). Make sure that the setting and change it to 100% and try printing again.

• HP EliteDesk 800 G2 Small Form: The front panel audio connector - this only made type to use for headphones and microphone

  Hello

  I am trying to determine what type of audio 3.5 mm plug to put into the connector on the front panel for the use of a headset to make video communications.

  could be - sleeve, ring and end cap (mono audio and microphone)

  or

  could be - sleeve, ring, ring and tip (stereo sound and microphone)

  Having read through the manuals and nothing is said on the type to use.

  Hello world

  Just plugged the connector 4 poles on my headset combination for my mobile phone (cellular) and the box of pop - up asked me to select headset or microphone - no selection for both.

  Looks like the right sleeve is for headphones only, and the left one is for headphones or micro - selectable by the user and not the two on a single sheet.

  Everything explained by the practice - but not the paperwork in the manuals.

  #5 for microphone or headset - menu popup is displayed after you insert a 3.5 mm plug to select that one but not both at the same time.  (So I can't use my headset to phone)

  Thank you

  Son

• Is it possible to extend the toolbar bookmarks over the line and do not have a drop down arrow?

  I know that the bookmarks toolbar is only a long line and I know how to add multiple toolbars (customization) but somehow I just can't get the bookmarks toolbar to expand to the next line or so. Is it possible that Firefox can do this or not?

  See:

  • Multirow Bookmarks Toolbar most: https://addons.mozilla.org/firefox/addon/multirow-bookmarks-toolbarplus/