Listed unknown network device

Similar Questions

• Satellite L500 - 19 X - Webcam listed as unknown USB device

  I had problems with my camera is not visible to the software Toshiba or Skype. Restart resolves the problem, but he then disappears again after a while.

  I downloaded the software for the Webcam from the Toshiba support Web page and reinstalled successfully, but now the webcam disappeared completely from the list of devices and shows simply Manager as unknown USB device.

  How can I get it back?

  Hey,.

  Important if you use the webcam: you can use it with one program! That means don't use Skype and webcam software at the same time. For example, if you use it for Skype, close the software of the webcam.

  If the webcam is shown as unknown device, you must reinstall the driver for the webcam I think.
  To control first the software list in Control Panel and remove Camera Assistant Software. After that, you should restart the computer and then reinstall the new software of the webcam.

• Satellite P200 (PSPB6E) - DVD listed as unknown in Device Manager

  The laptop loses DVD whenever I have laptop shutdown.

  Can operate again after that withdrawals upper filters in the registry, but is listed in the device as unknown Manager then does not yet work with an error code 10.
  Any ideas on this one?

  Hello!

  This boyfriend strange s, your drive is may be defective?

  Have you ever tried to remove the drive from Device Manager CD/DVD? After this restart the laptop and your drive should appear correctly. Check this box!

  What OS do you have? You have installed the latest service pack?

  Good bye

• Why the Personal Hotspot from my mobile phone appears in my list of list wifi networks if it is disabled on my phone?

  Why the Personal Hotspot from my mobile phone appears in my list of list wifi networks if it is disabled on my phone?

  On my iMac, there is an icon for a list of available to join Wifi networks.

  One of these Wifi networks is my iPhone Personal Hotspot.

  However when I look at my setup on my iPhone Personal Hotspot is off.

  I tried to join the Hotspot to my iMac and put.

  This is part of a feature called Hotspot instantly. It allows you to connect to your personal hotspot without your password or activate the hotspot on your phone. Don't worry, this does not allow other people to access your hotspot, only devices using the same identifier Apple will see your hotspot. This feature is not using any extra battery life when you're not connected to it. You can learn more about instant Hotspot here: OS X Yosemite: connect to the Internet using instant Hotspot

• M400 - Bluetooth is only recognized as a unknown usb device

  Hello!

  I have a problem with the bluetooth driver / stack. I just got my new M400 and the first time I have activated Bluetooth, battery Setup came - but Windows just said when Setup tried to install the driver that an error has occurred - nothing more.

  The Bluetooth ACPI works very well according to the Device Manager, but that's all. There are no other Bluetooth device list - but an unknown USB device. I compared the device with the id id in the inf file (which is located in the folder of installation of battery). This device is supposed to be the Bluetooth USB Controller-5 of TOSHIBA (USB\VID_0930 & PID_0508) but Windows does not recognize the device - and it is correctly listed in the inf file. Even if I try manually installing the Windows device requires just that the inf file contains no information about the device (which is not true).

  Any ideas what I can do? I already uninstalled the battery and installed the new version of the stack, but it makes no difference.

  Concerning

  Alexander

  I have it solved by myself. There is a defect in the file INF from Toshiba. From the beginning, it lists only Chicago as a compatible Windows version and windows compatibility control is a.

  If you change the string from Chicago to Signature = ' $Windows NT$ ' and out of the chain of compatibility that it all works very well. Unpack the battery Bluetooth to a folder, so just go to 2KXP/Windows/Inf and edit the inf file, then run the setup.exe in the folder 2KXP.

  Concerning

  Alex

• M40: unknown pci device (sd reader?)

  Hello

  I have reinstalled windows on my M40-149, and I have an unknown pci device listed in Device Manager. I've read other messages here, but I can't find a solution.
  I can t really think of something obvious, it could be, but I noticed that it doesn't do anything when I insert an SD card.
  I have a controller Cardbus Texas Instruments PCIxx21 / x 515, and a Texas Instruments PCIxx21 Integrated Flashmedia Controller is listed in Device Manager. I put t know if there should be one for SD cards but I see no driver for it on this website. So, any help would be greatly appreciated!

  Thank you.

  Hello

  It is listed as a driver for Texas instruments V 2.0.2.1 Cardbus. The download is possible under http://support.toshiba-tro.de/tools/Satellite/sm40/win-xp/cb-drv-sm40-xp-1021.zip.

  Good bye

• Always M70 - unknown PCI device

  Hello

  I formatted my M70 a re-installed with the Chinese version of XP. But there is still an unknown PCI device in the Device Manager list? I installed all the drivers in untility CD, but the problem is still there. Another problem is the function of CD play without opening the mechine. How to recover this function? There is no configuration file in the recovery CD.

  Thank you.

  [Edited by: admin on 8 January 06 15:26]

  Hello

  This document descript how to identify an unknown device in Device Manager
  http://support.toshiba-tro.de/KB0/TSB57014E000QR01.htm

• Networking the cDAQ-9188 - no 'network devices' Max

  Hi all:

  I have problems connecting my NI 9188 cDAQ via ethernet to my computer. MAX does not display it in his repertoire, or it displays "network devices". Based on the guide NOR offer, I don't know what else to do (I can't access the modules in a LabVIEW project which is my problem).

  I used the tool online browser that seems to be the equivalent of MAX and works very well - I can see the IP address of the controller and it shows what chassis slots are used by what the map.

  I tried manually inputing this IP in a remote system to the MAX, but that hasn't worked.

  Any ideas on how I can networks controller on my computer so I can actually use in a LabVIEW project.

  I have LabVIEW 2012 32 Bit. Would a student version be the cause of the problem?

  Thank you very much.

  cuaerospace wrote:

  I am familiar with the method you describe, but I agree with all the power cycling to get some of these products to work. I had to do this several times with the cRIO. Any chance you could give a little more than a description step by step explcit of your approach? Thank you!

  Good so here's what I did to try to reproduce and to have a step by step of what I had to do.

  Firstly I have reset my cDAQ so that it would be if all goes well in the mode that yours is.  To do this, I pressed the button to reset for 5 seconds then.  I have also all my network devices defined to "Obtain an IP address automatically" in the IPv4 settings in my network connections.

  After that, I start MAX.

  Go to devices and Interfaces > network devices, then I right click and choose Find devices.  It took a lot of time and the list was empty, but then I noticed that while he was always looking in this window, the MAX window showed my cDAQ-9188, who was a white device.  There, he registered the IP address as 169.254.93.149.  At this point if I went to the device to the MAX I saw where he sometimes States under network settings that no network adapters found.

  So I closed MAX and open my "view network connections" in Windows, I just searched that term in the start menu.  Then for my device properties, went to the IPv4 properties, set the IP address of 169.254.93.0 with 255.255.0.0 default gateway.  It is, so I'm on the same subnet as the appliance.

  I then restarted MAX now when I go to the device under devices, network and network settings I can set static IP and subnet is 255.255.0.0 10.10.10.100 then save.  Then closed MAX.

  Then I went back to my view network connections, the static value of what I really wanted is 10.10.10.0

  MAX then launched.  Find my device that is always white, click Add the device.  And then all is good.  I don't know if all these steps are necessary, and I don't know if there is an easier way, but it worked for me.

• driver for the unknown PCI device after having reinstalled Windows 8.1

  Hello, I have HP ENVY 15-j15ea and 2 problems with it.

  1. after reinstalling Windows 8.1 64 bit I can't find the driver for unknown PCI (bus 6), i.e. hardware ID:

  device PCI\VEN_10EC & DEV_5229 & SUBSYS_198A103C & REV_01
  PCI\VEN_10EC & DEV_5229 & SUBSYS_198A103C
  PCI\VEN_10EC & DEV_5229 & CC_FF0000
  PCI\VEN_10EC & DEV_5229 & CC_FF00

  I, ve tried this link, but it does not work: http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-123976-1&cc=us&dlc=en&lc=en...

  2 and what I need to install drivers for my laptop AMD A76M FCH mother/chipset card? I could not find driver for it, then maybe it is pre-installed with Windows 8.1?

  Help, please! Thank you!

  By the way: why it

  You are the very welcome.

  If you did not have a SMBus controller device listed in Device Manager in the category other devices, there is no need to install the chipset drivers amd that they would have been included in the database of the W8.1 driver if there is no listed SMBus Controller device after install W8.1.

• M6-1045dx Lodge: unknown PCI device

  Hi after upgrade to 8.1 windows. I have an unknown PCI DEVICE
  the envent says:

  \VEN_10EC&DEV_5289&SUBSYS_18A4103C&REV_01\4&f7495&0&00e0.
  and I'm having problems with my Internet, when the beginning of the OS everything is ok, but after a while my connection does not work.

  Thank you

  Hello:

  This device is the card reader that needs a driver.

  DL and install the driver first on the list on the link below...

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=15&PFID=25&level=4&Conn=3&DownTypeID=3&GETDOWN=false

  The BOM indicates your model has the Intel Centrino 2230 wireless card.

  The only suggestion I can offer would be to install the latest driver for this card directly from Intel.

  You want that element of fourth on the list (64-bit only driver).

  https://Downloadcenter.Intel.com/Detail_Desc.aspx?DwnldID=24576

• HP laptop - 17-p000na AMD R4: unknown PCI device

  Hello all, first time on this forum...

  I recently bought a HP 17 laptop p000na with AMD R4, it came with Windows 8.1 64-bit installed.

  I do not earn 8.1 and in all cases, some specialized software that I use is better coimpatible with Win7 32 bit, some older software works better on XP 32-bit, some same needs BACK... I therefore immediately has got rid of 8.1, partitioned the drive and installed Win7 64 bit, Win7 32 bit and XP 32-bit SP3.  I got a slow start installing these operating systems, but was eventually successful, it!

  I managaed to encourage drivers to just about everything in the Device Manager in the two Win7 32 bit and Win7 64 bit, a combination of AMD support site, HP, support from Realtek site support site. etc... But I find myself with an unknown PCI device in Device Manager.

  I hope someone can shed some light on what may be the PCI device and where can I download a driver for it.

  I still have to get arouhd to sort the XP drivers - I might wonder about this later!

  Thanks for reading,

  Simon

  Hi, Simon:

  If this is the label of the device, you must first driver on the list from the link below...

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=15&PFID=25&level=4&Conn=3&DownTypeID=3&GETDOWN=false

• my list of network services is turned off and it won't turn

  my list of network services is turned off and it won't turn

  do you mean;

  the list of devices on your network?

  in network and sharing Center, Center

  advanced sharing settings

  turn on network discovery

  then try a reboot... see if this leads him to the top.

• Network that connects to the unknown network will NOT cut

  My computer automatically connects to an unknown network that does not appear on the available wireless networks. It does not disconnect and to log only when I turn off the wireless network. If I connect to another network, it disappears. I can't find any info through the help who can tell me how th shut down my computer to connect to this network. It's windows vista 32 bit

  Try to remove all the networks listed there and restart.

  Network discovery: WE (if you can see other computers)

  All private network (Public's hotspots, airports, etc.)

  What you set security on?
  Rob - bicycle - Mark Twain said it is good.

• ProBook 645 G1: Network device did not have a driver installed pci\ven_10ec & dev_8168 & subsys 1992103C REV_0C

  Hi all

  I've installed WDS/MDT2010 to deploy the Windows & OS, it works with most of my models of HP laptops.

  When I deploy ProBook 645 G1 it gives me error foloowing.

  A connection to the deployment share could not be established.
  The following network device did not have a driver installed pci\ven_10ec & dev_8168 the & subsys C 1992103 & REV_0C
  Retry: try again to connect to the deployment share or give up.

  I have download all the network driver available for this model and imported in out-of-box driver, updated sharing deployment and run again but still having the same issue.

  Grateful if someone can help me on this.

  Thank you

  Hello:

  The only suggestion I can offer is to try the driver directly from Realtek.

  Second driver on the list.

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=13&pfid=5&level=5&Conn=4&DownTypeID=3&GETDOWN=false

• GANYMEDE + peripheral unknown network or Client AAA package

  Hi all

  I can do connect using the set of credentials to the ACS server, log it showed:

  "Reason for failure: 13017 receipt GANYMEDE + peripheral unknown network or Client AAA package."

  I know there are a few changes on GANYMEDE + room for new catalyst IOS, so I consult the guide and it is the end of my config:

  AAA server Ganymede group + TAC_PLUS

  the AUTH server name

  RADIUS server AUTH

  ipv4 10.10.21.251 address

  key xxxxxx

  AAA TAC_PLUS authentication connection group Ganymede + local line

  TAC_PLUS AAA authorization exec group Ganymede + none

  AAA authorization commands 15 default authenticated if

  accounting AAA periodic update 1

  exec accounting AAA TAC_PLUS start-stop group Ganymede +.

  network accounting AAA TAC_PLUS start-stop group Ganymede +.

  connect accounting AAA TAC_PLUS start-stop group Ganymede +.

  My platform is

  -C6500 running on IOS 12.2 (33) SXJ1

  -ACS 5.2.0.26

  Need advice on this subject, thanks

  Noel

  Hello

  What is IP IOS appropriate set to network devices and the AAA Clients for the candidate countries? If Yes, what IP address is indicated on the failure of the ACS that includes the error "GANYMEDE + unknown cover peripheral network or Client AAA? ACS reports as unknown IP address when it is already set appropriately?

  Kind regards.