lost internet access after the connection to the server

Similar Questions

• No Internet access after the connection of the cisco vpn client

  Hi Experts,

  Please check below config.the problem is vpn is connected but no internet access

  on the computer after the vpn connection

  ASA Version 8.0 (2)
  !
  ciscoasa hostname
  activate 8Ry2YjIyt7RRXU24 encrypted password
  names of
  !
  interface Ethernet0/0
  nameif outside
  security-level 0
  IP 192.168.10.10 255.255.255.0
  !
  interface Ethernet0/1
  nameif inside
  security-level 100
  IP 192.168.14.12 255.255.255.0
  !
  interface Ethernet0/2
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Ethernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  2KFQnbNIdI.2KYOU encrypted passwd
  passive FTP mode
  standard access list dubai_splitTunnelAcl allow 192.168.14.0 255.255.255.0
  INSIDE_nat0_outbound list of allowed ip extended access all 192.168.14.240 255.255.2
  55.240
  pager lines 24
  Within 1500 MTU
  Outside 1500 MTU
  IP local pool testpool 192.168.14.240 - 192.168.14.250
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access INSIDE_nat0_outbound
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Route outside 0.0.0.0 0.0.0.0 192.168.10.12 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout, uauth 0:05:00 absolute
  dynamic-access-policy-registration DfltAccessPolicy
  Enable http server
  http 192.168.14.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-3des esp-md5-hmac setFirstSet
  Crypto-map dynamic dyn1 1 set transform-set setFirstSet
  Crypto-map dynamic dyn1 1jeu reverse-road
  dynamic mymap 1 dyn1 ipsec-isakmp crypto map
  mymap outside crypto map interface
  crypto ISAKMP allow outside
  crypto ISAKMP policy 1
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 43200
  crypto ISAKMP policy 65535
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  a basic threat threat detection
  Statistics-list of access threat detection
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  !
  global service-policy global_policy
  password encrypted user testuser IqY6lTColo8VIF24 name
  username password khans X5bLOVudYKsK1JS / encrypted privilege 15
  tunnel-group mphone type remote access
  tunnel-group mphone General attributes
  address testpool pool
  tunnel-group ipsec-attributes mphone
  pre-shared-key *.
  context of prompt hostname
  Cryptochecksum:059363cdf78583da4e3324e8dfcefbf0
  : end
  ciscoasa #.

  Hello

  Large.  Try adding the below to make it work

  vpn-sheep access list extended permits all ip 192.168.15.0 255.255.255.0

  NAT (inside) 0-list of access vpn-sheep

  Harish

• Vista wireless loses Internet access after the mode "Eve".

  Environment:
  HP Pavilion dv2610ca notebook PC, broadcom 802. 11 b / g adapter, Vista Home Premium 32 bit SP2, Siemens Gigaset SE567 router/modem.

  Problem:
  I can usually connect wirelessly to my home network and to the Internet whenever I start my computer. However, I have close the lid and leave it in standby mode, I can't access Internet after I opened the lid and the system wakes up. The system connects to my home network but cannot access the Internet. It shows a Local access only.

  Diagnosis and repair fails generally, telling me that I have a problem with my router. Disconnect, then reconnect usually works. My router power market also works.

  I saw lots and lots of issues with Vista wireless networks and I followed several of the recommended actions:
  -updated the driver broadcom
  -reset the IP stack by using the tool "Fixit" of Microsoft
  -disabled the use of IPv6 in two by disabling the check marks in the related devices and changing the registry TCPIP6 parameters
  -modified the registry to activate/disable the DHCP broadcast flag in the TCPIP Interfaces
  -J' tell the system not to disable the card Broadcom, but the "Power management" tab mentioned in some articles does not appear in its properties. The only reference to power is "Minimum energy" under the "Advanced" tab, then I disabled who.

  Nothing has solved the problem.

  Has anyone else had this problem and fixed it?

  I'm not a technical Wizard, so please provide instructions for any action that you suggest.

  Thank you.

  I replaced the Siemens router/modem provided by my ISP (Telus) with an old D-Link router and separate modem 3Comm I had been using a couple of years and the problem seems to have disappeared.

  I'll close this thread on the assumption that the problem will not rear its ugly head again.

• No Internet access after the update from Windows 7

  Since the update of Windows 7 (from my list of update I can not single out one specific) sent 15 Dec - my computer will access my internet connection - the only way that I can access is to do a system restore to a point to Dec. 14 or before - I have a new computer - and no new programs have been added to the system during this time - it becomes troublesom because I have to constantly to do system restore to get online

  I called Support Center, Monday - and after having him work for almost 2 hours, we decided that the KB2467659 update is the culprit and we have disabled this update to be installed - HOWEVER the windows update program was H - LL BENT on installing this update - the technician called me back 2 days later Wednesday--and we did other things magic to ensure that this implementation to day has NOT been installed again - so far (knock wood) No recurrences of the problems

• Satellite A100-386: no internet access after the new XP installation

  Hi everyvody!

  I can do it myself, so I ask for your help!

  I have a Toshiba Satellite A100-386 with windows XP MCE.

  I recently had a virus, so I formatted my drive. I don't have the installation CD with me, so I install XP.
  I have two disc on my computer with the system and the other with the documents.
  Then I install ALL the drivers I could find on the Toshiba site for my computer.
  This means that the PSAA9E. The problem is that I have no internet! I don't understand why.

  When I look in computer management, I have no ethernet, controller mass storage controller and network controller.
  I have zone alarm as a firewall and an antivirus avast!

  I disabled avast to be sure that he's not in it but no result...
  In Thoshiba drivers there is also something to update the BIOS.
  I did it but I didn't change. I hope the problem here not there...

  It will be really nice to help me ^^

  Hello

  I think that you just have not installed the right driver LAN and WLan driver

  As much as I know this laptop supports Intel Pro 100 Lan and WiFi Intel 3945ABG card card

  Please visit the European driver Toshiba page again and download the compatible network driver and the driver WLan.
  Unpack the packages, then install it.

  Finally check again if the LAN and WLan cards were recognized in the Device Manager in network adapters.

  Good bye

• problem with Internet connection sharing, error: connection ad - hoc has "no internet access" on the cell phone of the customer

  Original title: problem with Internet connection sharing

  my laptop running on Windows Vista Home Premium SP2 (this one has access to the internet by using the dial-up modem and will to act as a sharer of internet connection or as a host) and the client computer runs on Windows 7 Starter

  in a first step, I try internet connection sharing, I've set up an ad hoc network and I just changed my setting modem dial-up on the sharing tab, of course what I change, it of 'Allow an other network users to connect through this computer internet connection' and choose the on Home Networking connection wireless network connection , then my mobile client to connect to a special that I created and portable client connected to the internet via ICS
  then the problem came when I restart my laptop. When I tried to use ICS once again, my customer laptop really takes a long time to connect, he continues saying 'identification' side host and client. and after that "identify" is complete, it says ad - hoc connection, I create has "no network".
  so, I'm a person answer in this forum
  ' Obtain an IP address automatically is the wrong setting on the Ethernet connection. "  To return to the sharing tab and unshare the wireless connection.  Close all windows network, and then open them and re - share the wireless connection.  Who must configure IPv4 for the Ethernet connection properties for:

  IP address: 192.168.0.1
  Subnet mask: 255.255.255.0
  Default gateway: no
  "DNS server: none.

  I put this on my laptop of the host, and and I put the IP address on my laptop customer in 192.168.0.2 with the same default gateway as my portable computer host IP

  and made some progress in this case, when I try to connect host and the client is no longer to 'identify' phase, immediately connected laptop both but my mobile client can not connect to the internet and displays "No Internet access" on the ad hoc network, I have create

  I tried a lot of things but always completed my mobile client can not connect to the internet and displays the message "no Internet access.

  What makes me confuse is first, I try to share the internet connection everything works like a charm, I set up an ad hoc network, and then change the setting on my modem dial-up so he can share the internet connection, and voila, computer laptop client connected to the internet. I change even not all IP settings

  But why after I restart my PC, this problem comes...

  someone knows how to help me with this problem?

  Hey, Mimbs,

  You can try the similar thread to the next with a possible solution:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/no-Internet-access-in-the-client-machine-when/77312e09-4385-41FA-A420-0c42be58e4e3

  Also for reference:

  http://Windows.Microsoft.com/en-us/Windows7/networking-home-computers-running-different-versions-of-Windows

• After that Windows 7 conclusion "No Internet access" in the wireless network?

  I have a USB wireless network card installed in my office. All judging by the "connected network" showed, that he manages to connect to my wireless router, with I can't visit all websites due to "free Internet access". Only if I move my router where (almost) no wall blocking the path between my office and the router, will be solved the problem.

  There is no problems surfing the Internet using my laptop (Windows XP) and the iPad, which also connect to the router.

  I don't know what "No Internet access" while "Connected network" appears. To understand this, perhaps I should know what Windows 7 draws the conclusion "No Internet access" to the wireless network.

  Thank you, everyone. I managed to figure out the problem last night. With this document that I found by Googling, http://www.usb.org/developers/whitepapers/327216.pdf, I tried to disconnect my DVD ROM USB plugged next to my wireless network card and found that this really WORKED, although the DVD ROM is USB 2.0 instead of 3.0.

  In addition, as Shawn "Cmdr" Keene [MVP] said, I really need to I ignore the message "connected network". I ran the Ipconfig/all command frequently and found that sometimes the IP address of my wireless network card was no longer * 192.168.0 and the gateway, and the IP addresses of the DNS servers are null, even if the message "Connected network" remained all the time.

  Hope this helps others who also have this problem, even though my English is not very good. : )

• I need to install Flash Player on a computer that does not have internet access. The 'flashplayer18_d_install.exe' I copied everywhere that 'no Internet' computer wants to deal in the internet to do something and of course fails. I need a ins

  I need to install Flash Player on a computer that does not have internet access. The 'flashplayer18_d_install.exe' I copied everywhere that 'no Internet' computer wants to deal in the internet to do something and of course fails. I need an installation file that won't connect to the internet. -help

  Hi colinkerr22,

  Offline installers are displayed at the bottom of the Installation problems | Flash Player | Windows in the section "problems".

  --

  Maria

• Network can not access the server after the server automatically upgraded to windows 10 last night?

  After the server has been upgraded to windows 10 by Microsoft yesterday evening, all PCs on the network require passwords which we never used.  How to fix and access the server?

  Hello

  I suggest you to post your query on our Forums TechNet social as this question should be better there.

  Please refer to the reference to the link below to send your request:

  https://social.technet.Microsoft.com/forums/en-us/home?category=Windows10ITPro

  Hope this information helps.

  Please get back to us with an update on the issue, we will be happy to help you.

• The screen of my Sony Vaio laptop VPCS11FM completely lost its brightness after the installation of Windows 8. What should do?

  I installed upgrading W7 W8. Already during the final phase of installation, the screen of my Sony Vaio laptop VPCS11FM completely lost its brightness after the installation of Windows 8. I tried the settings of brightness through the hardware buttons and in energy savings, but it remained the same. What should do? Karl

  Looking for a display updated sony driver.   Its always a good idea to do so during the updating of the OSs.

• No Internet access after restart on Windows 7

  Hey,.

  I have a HP Pavilion Dv6 with an Atheros AR9285 wifi adapter and it originally had windows vista installed. I just upgraded to windows 7 is a complete and the first format was fine, I could connect to the internet. After restarting my computer, I started to have problems of WiFi, it says I am connected to my router, but the network is unknown and there is no internet access. I am able to connect to the internet on the same router using my phone, my samsung laptop and none of my roommates have had this problem.

  After much research on google and search through discussions, I found that a lot of people have had this problem, but none of their solution worked for me.

  That's what I tried:

  • I have uninstalled and reinstalled my network card
  • I've disabled Hello, then went as far as uninstalling itunes
  • I have reset the TCP/IP stack
  • I do not have Metacaff
  • I don't have the service # Id_string (bunch of numbers)
  • I put my default gateway at the same address as my samsung that connects to the internet
  • I put my IP as shown in the following solution addresses

  IP address of 192.168.1.65 (does not etre.65)

  Subnet mask: 255.255.255.0

  Default gateway: listed on the bottom of your router's default IP address (for me: 192.168.1.254)

  -Click OK

  I does not require a reboot, you may need to.

  Nothing seems to work, so any ideas would be much appreciated!

  Original title: unidentified network / no Internet access after don't Reboot under Windows 7

  Hello

  1 did you do changes on the computer before the show?

  I suggest that you try the procedure described in the article below.

  Method 1:

  Why can't I connect to the Internet?
  http://Windows.Microsoft.com/en-us/Windows/cant-connect-Internet#1TC=Windows-7

  Method 2:

  Wireless and wired network problems
  http://Windows.Microsoft.com/en-CA/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win81tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  I hope this helps to solve the problem. Please come back for any clarification on this or any issue of Windows. We will be happy to help you.

• 'No Internet access' after reboot, but OK after cold start.

  My system has been restarted after a recent update of Windows, and although the Internet connection worked the status icon in the system tray showed the yellow triangle and "No Internet access." The State of the network has been "Identification." (This is a wired connection). When I tried to restart, shutdown took a lot of time and the system blue screened.

  When I started the system again, it worked OK. However, at each reboot later, I have the same problem and after each cold start, it's OK. On subsequent reboots, I notice that the Internet connection ends, and then returns to identify, even if the connection actually works.

  What is a next step of troubleshooting?

  Hello kwdavids,

  I suggest to perform a system restore to before the update was installed to see if it solves the problem:
  http://Windows.Microsoft.com/en-us/Windows7/products/features/system-restore

• AppPortal error: remote access to the server is not enabled

  I'm lost on this one.

  Using the full client of AppPortal on a Win7 64 bit machine (version 8.0 of the customer)

  Double-click the icon, download authenticated - published applications show, then double click a published application, the end user receives:

  Remote access to the server is not enabled.

  This happens only on a single computer

  From this profile of users on the given computer I can MSTSC on the same server without problem

  The error also follows the profiles on the given computer.

  I have closed the Antivirus and Windows Firewall and still can not get this to work.

  Even uninstalled and reinstalled the client.

  From my computer, I can easily log in as this user.

  Customers get automatically configured through an XML file.

  After installation, I tested this laptop and he always gave the same error.

  I ended up him to give me the phone for a few hours.

  Uninstalled the version that was there (build 8.0.0.forget) and scoured the Windows Explorer for all left overs (a little here and there in user profiles and delete).

  Then scoured the registry for expressions; vWorkspace, Quest Software and Provision Networks and remove all instances

  Reinstalled all THE SUCCESS with the new connector to our servers (8.0.306.1427)

  Thanks for the help Dave

• I'm not able to get wireless internet access after entering my security at the back of my modem key.

  I recently bought a thread to get a wireless connection after you plug the usb driver proceeded to create a connectin wireless, then asked to type in the security encrypted code that did got a connection but said auto and not Internet, but bars are high and shows a connection, I hope that I have been specific with the problem iam having.another thing on my laptop I have access to the internet and typed in the security key on the back of my modem... Tenda is the name of the usb driver.

  original title: no internet access

  Hello

  Are you binder to share internet from your laptop or your internet provider cable is connected to this wireless USB dongle / device?

  If you share internet by connecting this USB to a computer, you will need to share internet on this computer.

  You must enable "Internet connection sharing", click on Start menu-> network connections-> right click on the connection to the LAN-> select properties-> click on the tab 'Advanced'-> Tickmark 'allow other users to connect through this connection to computers.

  I hope this helps.

• No internet access for the connection with the router.

  I bought a router D-Link DSL-2750U and when I connect to the internet it says no internet access even I've updated the MAC address of my router with my ISP, but still no use I use don't win 7. any help on this?

  Hi Chavigny,

  In case you have contacted the ISP provider and verify that the network settings are correct, then try the following steps:

  Method 1:

  I suggest to run the network troubleshooter, and check to see if it lists all the errors and helps you solve them.
  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Method 2: Update the network driver.

  Steps to update of network driver:

  (a) click the Start button.

  (b) in the search box type devmgmt.msc, and then press ENTER.

  (c) select the network card device and right click on it

  (d) now select Properties.

  (e) in the Properties window, on the driver tab, click Update driver.
  After installing the updates, restart the computer.

  For more information visit: http://windows.microsoft.com/en-us/windows7/Update-a-driver-for-hardware-that-isn ' t-work properly

  Please refer to:

  Why can't I connect to the Internet?

  Previous post: the State of the question.