low frequency with labview 2010 auto and agilent 35670a
Hello
I work on the automation of low-frequency measure a 35670A Agilent. I currently did a program that allows a measurement with an average of FFt given a frequency bandwidth and frequenct from beginning, see picture attached, but I try to measurement of spectrum using this power VI ( ), but unfortunately I can't seem to find how to convert a signal from my block diagram below in order to send the input signal power VI above spectrum X no indication or help will be appreciated.
Tags: NI Products
Similar Questions
-
Language setting bad compile App with labview 2010 SP1
Hello
I got this when I create an application with LabVIEW 2010 SP1
My OS is a Windows XP English with a regional setting to English (Canada)
Y at - it a fix for this problem, that some were.
After a repair of my SP1 installing LabVIEW 2010 I had the correct behavior
I think something was wrong in the installation of runtime LabVIEW 2010
-
You use HP 4156 instrument with Labview 2010 in Windows 7
We recently bought Labview 2010 for Windows 7 and some software porting, we had on Labview 6. These programs of control of two instruments: HP (Agilent) 4156A parameter Analyzer and the Keithley 7001 switch system. When I looked for the drivers of instruments for these two systems, they were no longer available for Labview 2009 and associated NI-VISA 3.2 driver is not compatible with Windows 7. You have any suggestions on how we can run Labview 2010 on Windows 7 with the ch (Agilent) 4156 A and Keithley 7001?
A pilot in 2009 can be loaded in 2010 and this is the minimum VISA version, you can use. You need not even the driver of instruments most recent. Just run your existing code.
-
The PSC-2000 is programmable with LabVIEW 2010 SP1 / Real Time 10.0.1?
I have a PSC-2000 camera I want to use for a small project. I see on the site OR that it is said»
- "Support for LabVIEW Real-time 8.5.1 and earlier" and "Support for Windows Vista and earlier versions. It means that I can not use the latest version of LabVIEW (2010 SP1) with time real (version 10.0.1) running on a Windows 7 computer? If not, what version of LabVIEW, real-time and operating system do I need?
-
Hello
I intend to use Labview 2010 in no time.
But before I go to use it I have a few questions.
- I know that it is possible to run Labview 2010 in an XP environment. But is it also possible, when running Labview 2010 on an XP system, to build a project for a version that is useful in a Windows 7 environment?
- Or should I run Labview 2010, when I want to build a project that is useful on a Windows 7 system, on a system with Windows 7?
Please give me some information.
I hope to hear from you soon.
Kind regards
Kenny
the file (.exe) is also compatible with xp and seven, no need to change anything...
Concerning
-
LabVIEW 2010 - applications and issue of RTE
Hello
I am currently using LabVIEW 2009 and my company is upgrading to 2010, and I had a few questions on creating applications and their execution on other computers to open the switch.
(1) computers that don't have that installed LabVIEW 2010 runtime will be able to run applications developed with LabVIEW 2009 (and earlier versions)?
1.1) in the contrary case, we will have to rebuild all of our current programs to use the RTE of 2010?
(2) Conversely, exes, built in 2010 will be able to run on computers that have the installed 2009 RTE?
(2.1) if not, is there an easy way to downconvert programs written in 2010 so that they run on RTE in 2009?
(2.2) that we will be able to use the new features in 2010 (as the network streaming, export to excel graphs) if we downconvert for 2009?
3. If rebuild us some applications that were originally written in 2009 us will it install the RTE of 2010 on the target computers, so that they can run the new version of our application?
Thank you!
-Nick
Applications created in 2009 should the TENS of 2009. Similarly, applications created in 2010 must RTE of 2010.
You can install both engines to run on the PC at the same time. Your .exe will use it is appropriate based on what version it was built in.
-
Need help with Exchange 2010 Diag and implementation
I NEED HELP FOR EXCHANGE 2010 DAG AND THE IMPLEMENTATION THAT CAN HELP-IM I IN THE RIGHT SUPPORT GROUP?
Hello HectorLopez_790,
Microsoft Communities is for consumer issues with Windows 8, Windows 7, Windows Vista and Windows XP. Your question with Exchange would be better supported in the TechNet forums.
Click here for a link to transfer your question in the forums of Exchange.Thank you
Marilyn
-
ERR (1097) with LabVIEW 2010
Hello
I have improved my code LabVIEW 2009 to 2010. When I run, I now get a ' (1097) ERR ' some of my objects .dll. Does anyone know why this is? (Note that my .dll is just hanging out in a directory and do not part with my PC)
Thank you, Alec
Hello Alec
Thanks for your post, I'm the engineer who will support you. If I understand correctly, you upgrade your system and have encountered any errors with your dll. I did a search on our Web site for the error code and found an article that addresses the problem that you have. If you have any other questions do not hesitate to contact us.
Thank you
-
Can I use NEITHER-DAQmx 8.6 with LabVIEW 2010?
Can I use the software version 8.6 OR DAQmx on LV 2010? Or do I have to use the corresponding versions?
-
Problem with LabVIEW 9.0f2 and VISA 5.0 on Mac OS x 10.6
Hello
I'm using MacOSX 10.6 and Labview 9.0f2. I installed the lates VISA (5.0.0) drivers, as they are the only support OSX 10.6.
Now, I try to run the "basic series write and read" example and get the following error:
Error 1073807343 has occurred to the property node (arg 1) visa set up a Serial Port (Instr) .vi-> basic series writing and Read.vi
Possible reasons: VISA: information about insufficient localization (Hex 0xBFFF0011) or the device or resource is not present in the system.
As I am a newbie to Labview, I'd appreciate any help on this...
Thank you
Daniel
Hello
You do not have a device series on behalf of resource, you use to write and read and take?
Did you check with Max OR and log on to this device.
-
LabVIEW 2010 FPGA: problem with the mean and the variance Subvi
The Subvi 'Average, Variance and standard deviation' seems to not work properly. The calculation of the average value is ok but std and variance are bad and the results change with representation in an unexpected way. Everyone knows about this problem? Is there a problem with the use of this function?
Thank you
Andrea
Hello Andrea,
Here is a test for the configuration of your VI (entered I16, 16 samples), saved in LabVIEW 2010 SP1 and the new Subvi. It is relatively simple to adapt it to other configurations, but it does not reconfigure several nodes and constants on the diagram. Let me know if it will work for you.
Kind regards
Jim
-
The jury of ELVIS will work with LabVIEW Student Edition 2010
Hello
This question was asked in the forums of LabVIEW, but no solution has been found. I have a windows 7 x 64 machine with LabVIEW 2010 Student Edition. When I try to install ELVIS 3.0.5 traditional software I get the following (no error code) message: "this Setup program requires the LabVIEW 8.5 development system or later to be present on this computer. Development system LabVIEW Base in any version of LabVIEW is not supported. Please install LabVIEW and then rerun setup of NI ELVIS. »
I also installed the DAQ software for PCI DAQ board. I do not have access to a 32 bit machine and do not know how to get my board work (no ELVIS II) ELVIS. I have provided a screen shot of the message during the installation of the software of ELVIS.
.
Hey dduong16,
Thank you very much for taking the time to provide additional information. After talking with several experts about your system, we concluded that this error is the result of an incompatibility between 3.0.5 Elvis and LabVIEW 2010 64-bit. Even the latest drivers of Elvis are not yet supported by 64-bit LabVIEW: see notes in support of the operating system on the Readme Elvismx 4.2.3
To solve your problem, you will need to uninstall the 64-bit version of LabVIEW and install a 32-bit version. If you are a student, you should be able to get this version of your computer (it will work fine with your Windows 7 64-bit OS - it will install on 32-bit OS emulated inherent in your system). If you are not a student, please send me a personal message, and we will be working with an account representative to get you the necessary version.
I apologize for the inconvenience, this made you and appreciate your patience. We have updated the Elvis 3.0.5 Readme to reflect this incompatibility (the change may not appear yet, because it takes time to propagate through our system), and I'm trying to create a Base of knowledge on the subject article to help future users who encounter this error.
If there is anything else that I can help you, please you after return. Thank you!
~ kgarrett
-
Setup of NOR-time with MAX in LabVIEW 2010
Hello
I have a set of PXI systems running LabVIEW 2010 RT and want to start using NOR-time for my timestamp. My systems have NEITHER time 1.0.1 installed and NEITHER-Sync 3.2.1 installed. I have a system with a PXI-6682 card in slot 2 and got got to pull time of a GPS antenna.
When I go to MAX on any of these systems, I briefly see "search sources of synchronization of time...". "in the settings of the time and then nothing. I do not see the fields displayed in this screenshot:
http://zone.NI.com/DevZone/CDA/tut/p/ID/11466
What Miss me?
You reply to my message, looks like it is is not currently supported in NO-time 1.0.1 in MAX and will not be until the next version of NO-time.
-
LabVIEW 2010 help control Source code...
I'm trying to set up Tortoise SVN to work with LabVIEW 2010. I was able to get lvmerge and lvcompare to work by adding them to the list of programs within the turtle, but leave in LabVIEW there is a section to configure the source control I have a problem with. Under "Configure Source code control" there is a drop down to the name of the Source control provider. There is only one option: < none=""> . I looked into it a bit online and found that LabVIEW running in Windows searches the registry database for a list of the sources of control. I don't know exactly what he's looking for in the registry, but maybe I could make an entry in the registry to get LabVIEW see Tortoise SVN. Anyone had this problem or any experience with this?
To use the NCC options provided by LabVIEW you will need from a provider. For subversion, it is possible with the PushOK SVN SCC plugin.
If you install you can checkin/checkout directly from the LabVIEW project environment.
If you really like TortoiseSVN discover the Tortoise SVN integration made by JKI-software.
Tone
PS there is nothing special about 2010 in the integration of the CSC.
-
'LabVIEW 2010'.exe as a windows service running
Hi all
years, I wrote an application with LabVIEW 7.1 and transformed into a Windows NT Service according to this NOR-tutorial.
Now, I have a similar use case and I wanted to do the same thing with an application built in LabVIEW 2010.
Somehow, it does not work and I still get the error 62.
I built a simple demo application once with LV7.1 and once with LV2010.
I was able to use this service when they built with LV7.1 but not the version of LV2010 (client-side I always used LV2010). He has no problem with the connection to the server or using the port.
I'd rather not rebuilt the app with LV7.1 because it is not really small. I consider that if there is no work around for this problem.
Anyone any ideas?
I really appreciate anyone's help
See you soon,.
Christian
As well as information for those who execute it in the same problems:
SC.exe toured BUT not as described in this tutorial. You must create a wrapper function as described on this Homepage. Services created with sc.exe need a BeginService() and an EndService() method otherwise it wont let you install.
This image shows you how I did it. The CIN AnyService.dll of charges that loads server.dll.
Kudos to Kuan Chen
See you soon,.
\c
When I tried to add a new target under LabVIEW 2010 SP1, the PSC-2000 was not among the choices.
As the support NOR documents indicate, you need LV version 8.5.1 or earlier to program the cFP-20xx devices family. Version 8.5.1 of LabVIEW does not work under Win7. You will need Windows Vista or something earlier like XP.
Maybe you are looking for
-
I have a computer in my summer residence and one to my winter home. They both run Thunderbird for my emails. When I move one residence for others, I want to update my address book Thunderbird. I do it by selecting - address book - tools - export, on
-
Need driver for Edimax IEEE 802.11 g Mimo wireless cardbus
Hello. I use PC toshiba laptop (model No. PSA50E-07203TG3), and I want to install the device called: "IEEE 802.11 g cardbus wireless MImo Edimax.My computer fails to install Automatlly, and I have no CD with it. Can you please give me a software to i
-
I received phone calls from the apparent 'technical Microsoft LCC online'?
I continue to receive phone calls daily from the apparent 'technical Microsoft LCC online' they say mistakes keep produce and seem very determined to get in touch, but I'm suspicious because I don't know how they got my phone number and they will not
-
I am a worker full-time, a student of FAU - back for 2nd career who is the single parent of a 9-year-old child severely disabled. I used all the programs, but I'm NOT SAVVY to fixing problems and feel that my life is spiraling out of control BECAUSE
-
I am running XP Media Center SP2 on an old HP Pavilion AMD Atholon. SP3 has been installed, but underwent an important announcement problem had to go through the recovery. Whenever I am trying to reinstall SP3, XP does not except in safe mode. SP3