lrt224 dual wan router

Similar Questions

• Dual WAN router and protocol binding

  Hello! I'm trying to find a dual WAN router with support VPN, which allow me to redirect part of the traffic to a specific port WAN and balancing of this specific traffic in the case of this WAN failure (the latter is preferred but is not entirely necessary) load.

  RV042/G could help me with this? In this case, allow redirection Protocol only? What port/ip forwarding? Or some sort of filtering of packets to redirect to specific WAN ports?

  Maybe I need another router in the conduct of business?

  Thanks in advance!

  Hi Jose, RV0XX model (g) supports a protocol source LAN link to extended network destination set. It can be a host of high-end LAN or a single host LAN. It may be the customer service or all services. In the case of a failure of network SCOPE, all links in the Protocol are "ignored" and switch to the active WAN until normal operation is restored.

  -Tom
  Please mark replied messages useful

• LRT224 - Dual WAN port forwarding

  Can you move forward say port 80 1 Wan IP and port 80 from WAN 2 to a different IP address. ?

  Also can you somehow choose TCP & UDP rather large only one or the other?

  I just replaced 2 routers with LRT 214 and LRT 224 TPLink its all works well. Except port forwarding

  With LRT224, a port forwarding rule is applied to the two WAN ports and two rules are necessary if you want to ship to TCP and UDP to the same internal IP address.

• Dual Wan router inaccessible RV042G after the configuration management of bandwidth

  Hello

  I bought a router of RV042G a few days ago to manage 2 lines adsl at my home. Everything works fine except for one thing: I can't configure bandwidth management. When I go into the menu "Bandwidth management", "Type of bandwidth management" then I choose the frequency control or priority and I have a had a few rules to prioritize the http protocol, for example, then I click the button Save. After a few seconds of internet use I loss the router and internet connectivity and 192.168.1.1 became inaccessible Ping. I had to unplung the power cord to restart the router, the same problem persists until I have remove all the rules! A few times I even had to do a factory reset because my adsl modem is inaccessible behind the router (impossible to do a ping to the gateway).

  What can I do? There is a known issue on this router and firmware? I have:

  Serial number:		NKS16220141	Firmware version:	v4.2.1.02 (January 18, 2012 14:10:55)
  VID PID:		RV042G V01	The firmware MD5 checksum:	a9817f2dbdcbd6a5c109eaa21b1c3545
  LAN			Working mode:	Entry door

  Thanks for your help.

  Could Pascal you please make a backup configuration file.

  Then I would you at the factory to reset the router then once he comes back to the top, login, make your internet work and try the management of bandwidth again without any other configuration. See if it has the same problem.

  If not then this would imply some there is a configuration in conflict with the previous establishment or a software defect that has been corrected through the reset.

  -Tom
  Please mark replied messages useful

• RV082, Dual Wan, VPN + protocol bindings

  Hi all

  I have this kind of Setup and I can't figure out how to think this router.

  My Installer uses Dual Wan load balancing mode. I only need one VPN tunnel. High availability is my concern.

  Site 1 has fiber and Cable

  Site 2A cable and FTTN

  Each ISP provides a static IP

  VPN works very well in the event of failure. I am always disappointed that it works in the case where a single primary WAN breaks, but is not operational if primary WAN on Site 1 stops at the same time secondary Site WAN 2 stops. It is very rare but can happen.

  In any case, my problems are where I need binding protocol to ensure secure WEB (https, banking, portal provider) sessions.

  I bind, at the least, port 443 to my primary WAN. In this way, I can access the Web sites and keep me logged.

  So, if I browse a HTTPS across the VPN server, binding protocol always attempts to pass port 443 by the WAN1. He will not even consider the VPN as a valid route first.

  (Maybe) can problem I reduce Hop Count for Site 2 less than 35?     P.S. I replaced the addresses I don't think they are relevant.

  Destination IP Subnet mask Default gateway Number of hops Interface

  ADDR network WAN2 255.255.255.252 * 0 eth2 WAN1 network addr 255.255.255.248 * 0 eth1 Site 2 255.255.255.0 Site 1 fiber Gateway 35 eth1 Site 1 255.255.255.0 * 0 eth0 by default 0.0.0.0 Site 1 fiber WAN1 15 eth1 by default 0.0.0.0 Site 1 cable WAN2 40 eth2 by default 0.0.0.0 Site 1 fiber WAN1 40 eth1

  Thank you all,

  Bruno

  I would like to conclude this is a bug and requires further investigation. I wouldn't call it a limitation if it was my decision (not that I have so much importance in this regard)

  -Tom
  Please mark replied messages useful

• If I have 2 routers when I connect 2 LAN to LAN or WAN router connection LAN router?

  If I have 2 routers when I connect 2 LAN to LAN or WAN router connection LAN router?

  Hello

  It suits better the question you have posted on the MSDN forums. Please ask your question in the following forum.

  http://social.msdn.Microsoft.com/forums/en-us/categories

  Hope this information is useful.

• Crash computer after installing Netgear N600 Wireless Dual band Router WNDR3400. My detail of error says I may need to update my BIOS to 8400 has 09 but I can't seem to download the desktop to install.

  My computer crashes after I installed the Netgear N600 Wireless Dual band Router WNDR3400.   I uninstalled and then reinstalled, but my home computer still crashed.  My detail of error says I may need to update my BIOS to 8400 has 09 but I can't seem to download the desktop to install.  Any suggestion?

  Hi JudyWinn,

  If you need assistance for updating BIOS (Basic Input Output System), I recommend you contact the manufacturer of your computer to update the BIOS (Basic Input Output System) & check if the problem persists.

  Note: Changing the BIOS / chipset can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/chipset can be solved. Changes to settings are at your own risk.

  Hope the helps of information.
  Please post back and we do know.

• Tunnel VPN RV-042 for Dual WAN Failover backup function

  We have customers with dual WAN failover scenarios with site-to-site VPN tunnels.

  In the past, the VPN tunnel backup feature has been available in the RV-082.

  One of the new RV-042 firmware versions have the function of backup Tunnel VPN available?

  The feature is supported on the RV042 V3 hardware.

• sparse mode multicast edge WAN router

  Hi all

  I hope you well. I have a problem of multicast and I was wondering if anyone can help. We have several remote sites connected to the router end hub and some sites are unable to receive multicast streams. We use the pim sparse mode with RP static. whenever I try to do a ping to a lan switch multicast stream I get

  (*, G) entry with correct PR, RPF nbr and the incoming interface on LHR but oil mill interface iam get none. on the last jump (LHR) router I see interface OIL as pointing as the igmp join query comes from LAN to lan.

  I see (ip lan of the CBC, G) entry in the table mrouting but interface new entrant is pointing to lan, no details of PR and outbound interface is WAN.

  can you advise or point iin right direction. Thank you

  concerning

  M

  You will see that because the switch acts as a source for a stream multicasting if your WAN router it records correctly.

  If you try to troubleshoot multicast on the remote receiver then the above is not a valid test and tells you nothing.

  What is the address of muilticast group you are trying to reach the remote site?

  That shows the mroute for this group address table?

  Jon

• IPSEC VPN on the dual WAN links

  Here's my situation. I have two identical sites ASA 5505 and each has the dual wan/ISP connection and are set to resume using the sla monitor followed. I would like to create a vpn between these two sites that remains active regardless of what ISP link is online. Just make two crytpo card statements10 and a 20 inside each of the asa to each of the other ASA STATIC PUBLIC IP? It works or cause problems?

  Configuration of SITE B

  card crypto Cox_Primary_map 10 corresponds to the address Cox_Primary_cryptomap_10

  crypto Cox_Primary_map 10 peer 72.X.X.X card game<== primary="" static="" isp="" at="" site="">

  10 Cox_Primary_map transform-set ESP-3DES-SHA crypto card game

  card crypto Qwest_Backup_map 20 corresponds to the address Qwest_Backup_cryptomap_20

  crypto Qwest_Backup_map 20 peer 98.X.X.X card game<== backup="" static="" isp="" at="" site="">

  Qwest_Backup_map 20 transform-set ESP-3DES-SHA crypto card game

  tunnel-group 72.X.X.X type ipsec-l2l

  IPSec-attributes tunnel-group 72.X.X.X

  pre-shared-key adadsfasdf

  tunnel-group 98.X.X.X type ipsec-l2l
  IPSec-attributes tunnel-group 98.X.X.X

  pre-shared-key adadsfasdf

  Thank you

  Jesse,

  One of the solutions to your problem is to apply the same for both interfaces crypto card and have the two counterparts mentioned under a crypto map entry.

  Since you're using track/IP SLA to activate a single link to a single IP address of time will be answers.

  http://www.Cisco.com/en/us/docs/security/ASA/asa84/command/reference/C5.html#wp2278871

  Have several inputs card crypto with the same statement in game will cause problems.

  Hope that makes sense.

  Marcin

• RV042 Dual WAN Port DMZ not acquire an IP from ISP

  Hello

  I am trying to replace my router with the more robust RV042 of current load balancing. Installation seems simple enough. However, I am having an issue gets an IP address of the DMZ port in load balancing mode.

  The two WAN is the same ISP and is both DSL, using the same models of DSL Modem. #1 WAN port works perfectly.

  Indeed, when an independent piece of equipment is installed in the #2 DSL modem, this gives an IP address instantly...

  The two DSL lines only require a MAC address to get their IP addresses, and none of the static values are allowed, perhaps to test only.

  The issue of intellectual property has been seen before. I can't find any reference to the iton this site.

  Thank you

  Steve

  Glad to hear that it works.

  The "save the settings and restart" is not all that rare, although it is not typical for your model.

  The obligation of power off is certainly not normal. He told me that some sort of electric lock has occurred. This could be a unique thing, caused by a discharge of static electricity, or it could indicate a manufacturing defect. If this is the first case he did re - is probably. If it is the latter, then it will need a trade at any given time.

  In any case, it seems that the MAC address index has been at least partially useful.

  Good luck, somone will be here if you need assistance once again.

• RV82 Dual WAN and online banking. Packages of two IP addresses

  Hi all

  I have a set RV082 in place with two different ISPS (load balancing). Some time ago, users began to experience problems with online banking. It seems that the banking system set up more than a 'channel' to/from the end user and that bank systems won't accept that the packets come from 2 different public IP. I solved this by linking all HTTPS traffic to WAN1.

  Is this a good solution or is there a better way to deal with this? I'm afraid that it will be 'imbalance' my network as many services like Netflix and Youtube is HTTPS.

  Are there other services online that may have problems with a configuration of load balancing?

  If WAN1 breaks down. WAN2 will start HTTPS transport even if HTTPS is related to WAN1?

  I also have a similar problem with the router alert (goes to wrong ISP each time second), but this seems to be fixed in the latest firmware:
  "Authentication of email account is configurable for email alert".

  Thanks in advance

  Jone

  Hello James,

  Your solution is correct.  Certain types of secure connection HTTPS or SSH will not work if you keep changing IP address source, because it breaks the three-way handshake.  To avoid that you binding memorandum of installation you have.  You can do the same for all other traffic must always go out to a certain port WAN.

  If the WAN connection selected for protocol links to crashes, he switched to the other WAN until the connection retrieves.

  I have not seen too many online services that have problems with the load balancing is especially with secure connections, namely HTTPS.  I tried to access the HTTPS, Netflix, but I could never get an encrypted connection, but your best bet is to monitor and observe the network to see how it affects you.

  I mean the line you are citing has to do with the configuration of authentication to an SMTP server to send alerts by e-mail, rather than choose a port WAN to use, however if you protocol links SMTP to the WAN you would use that should no longer be a problem.

  Hope that helps,

  Christopher Ebert - Advanced Network Support Engineer

  Cisco Small Business Support Center

  * Please note the useful messages *.

• Connections RV042G Dual WAN

  We are a Cisco DPC3825 provided by our ISP cable modem connection.  It has been configured to act as a switch only.  They provided us with 2 static IP addresses.

  When each WAN port is connected individually, all right.  I see the IP addresses on the respective WAN port, and it works fine.

  When I connect the two WAN ports to the modem at the same time, I see a large amount of traffic between the WAN ports, as indicated by the port LEDs, and the RV042G becomes totally inadmissible through its web interface.

  How can I get the RV042G working with two connected WAN ports?

  Hi Rory, I'm not sure that the CPD is designed to aggregate in this way traffic. I wouldn't be surprised if he made a loop network, especially if you see a lot of broadcast or multicast packets.

  The most typical deployment has usually 2 connections that are unique modems.  I would suspect your 2 static IP addresses are on the same subnet / block ip that the router do not know how to react to load balance this scenario since he's going to the same destination in turn causing a loop until resources are consumed.

  -Tom
  Please mark replied messages useful

• Site to Site &amp; Dialer Dual Wan VPN

  Hello!

  I have some problems with a Cisco 1941 running 15.2...

  I have two interfaces WAN ADSL (PPPoE Dialer). I want normal Internet traffic through DSL - 1 and VPN through DSL - 2. So I put the default route through Dialer1 and the route heading to the IP of the Brach-Site (R.R.R.R), through Dialer2.

  on the R1: Ping R.R.R.R-> works fine

  A2: Ping Y.Y.Y.Y-> works fine

  R2: ssh Y.Y.Y.Y-> works fine

  so I guess that routing should work?

  but the VPN be established:

  router-wi #show cry sess

  Current state of the session crypto

  Interface: Dialer1

  The session state: DOWN-NEGOTIATION

  Peer: Port B.B.B.B 500

  IKEv1 SA: local X.X.X.Xremote of 500 B.B.B.Bidle 500

  FLOW IPSEC: allowed ip 172.20.100.0/255.255.255.0 172.20.110.0/255.255.255.0

  Active sAs: 0, origin: card crypto

  FLOW IPSEC: allowed ip 192.168.100.0/255.255.255.0 192.168.40.0/255.255.255.0

  Active sAs: 0, origin: card crypto

  Interface: Dialer2

  The session state: down

  Peer: B.B.B.B port 500

  FLOW IPSEC: allowed ip 172.20.100.0/255.255.255.0 172.20.110.0/255.255.255.0

  Active sAs: 0, origin: card crypto

  FLOW IPSEC: allowed ip 192.168.100.0/255.255.255.0 192.168.40.0/255.255.255.0

  Active sAs: 0, origin: card crypto

  Even when I remove the Card Crypto VPN - D1, without VPN can be established. Only when I stop the Dialer1 interface and the default Route also goes throug Dialer2 VPN is properly set up.

  R1 config:

  .....

  track 1 ip sla 1

  period 5-2

  !

  Track 2 ip sla 2

  period 5-2

  !

  crypto ISAKMP policy 1

  BA aes 256

  sha512 hash

  preshared authentication

  !

  ISAKMP crypto key xxxxx address R.R.R.R

  ISAKMP xauth timeout 10 crypto

  !

  Crypto ipsec transform-set esp - aes 256 esp-sha512-hmac VPN_TS

  !

  map VPN crypto -D1 10 ipsec-isakmp

  defined by peer R.R.R.R

  game of transformation-VPN_TS

  match address VPN_1

  map VPN - D1 20 ipsec-isakmp crypto

  defined by peer R.R.R.R

  game of transformation-VPN_TS

  match address VPN_2

  !

  map VPN crypto -D2 10 ipsec-isakmp

  defined by peer R.R.R.R

  game of transformation-VPN_TS

  match address VPN_1

  map VPN - D2 20 ipsec-isakmp crypto

  defined by peer R.R.R.R

  game of transformation-VPN_TS

  match address VPN_2

  !

  interface GigabitEthernet0/0

  Green description

  no ip address

  IP virtual-reassembly in

  IP tcp adjust-mss 1412

  automatic duplex

  automatic speed

  !

  interface GigabitEthernet0/0.1

  Wlan (network VPN_1) description

  encapsulation dot1Q 2 native

  192.168.100.2 IP address 255.255.255.0

  NBAR IP protocol discovery

  penetration of the IP stream

  stream IP output

  IP nat inside

  IP virtual-reassembly in

  !

  interface GigabitEthernet0/1

  Orange Description

  no ip address

  IP tcp adjust-mss 1412

  automatic duplex

  automatic speed

  !

  interface GigabitEthernet0/1.1

  Description VPN_2 network

  encapsulation dot1Q 1 native

  IP 172.20.100.2 255.255.255.0

  NBAR IP protocol discovery

  penetration of the IP stream

  stream IP output

  IP virtual-reassembly in

  !

  interface FastEthernet0/0/0

  Description-= DSL-1 =-

  no ip address

  automatic duplex

  automatic speed

  PPPoE enable global group

  PPPoE-client dial-pool-number 1

  !

  interface FastEthernet0/0/1

  Description-= DSL-2 =-

  no ip address

  IP virtual-reassembly in

  automatic duplex

  automatic speed

  PPPoE enable global group

  PPPoE-client dial-pool-number 2

  !

  interface Dialer1

  Description-= DSL-1 (Vdsl) =-

  the negotiated IP address

  IP mtu 1452

  NBAR IP protocol discovery

  penetration of the IP stream

  stream IP output

  NAT outside IP

  IP virtual-reassembly in

  encapsulation ppp

  Dialer pool 1

  Dialer-Group 1

  PPP authentication chap callin pap

  PPP chap hostname [email protected] / * /

  PPP chap password 0 xxx

  PPP pap sent-username [email protected] / * / password 0 xxx

  card crypto VPN - D1

  !

  interface Dialer2

  Description-= DSL-2 (T - DSL) =-

  the negotiated IP address

  IP mtu 1452

  NBAR IP protocol discovery

  penetration of the IP stream

  stream IP output

  NAT outside IP

  IP virtual-reassembly in

  encapsulation ppp

  Dialer pool 2

  Dialer-Group 2

  PPP authentication chap callin pap

  PPP chap hostname [email protected] / * /

  PPP chap password 0 xxx

  PPP pap sent-username [email protected] / * / password 0 xxx

  card crypto VPN - D2

  !

  .......

  !

  The dns server IP

  IP nat inside source map route DSL - 1 interface Dialer1 overload

  IP nat inside source map route DSL - 2 interface Dialer2 overload

  IP route B.B.B.B 255.255.255.255 Dialer2 10 track 2

  IP route 0.0.0.0 0.0.0.0 Dialer1 30 track 1

  IP route 0.0.0.0 0.0.0.0 Dialer2 50 track 2

  !

  VPN_2 extended IP access list

  IP 172.20.100.0 allow 0.0.0.255 172.20.110.0 0.0.0.255

  VPN_1 extended IP access list

  IP 192.168.100.0 allow 0.0.0.255 192.168.40.0 0.0.0.255

  !

  radius of the IP source-interface GigabitEthernet0/0.1

  ALS IP 1

  X.X.X.X ICMP echo

  tag Check DSL-1

  threshold of 300

  timeout 500

  frequency 5

  IP SLA annex 1 point of life to always start-time now

  ALS IP 2

  Y.Y.Y.Y ICMP echo

  tag check DSL - 2

  threshold of 300

  timeout 500

  frequency 1

  IP SLA annex 2 to always start-time life now

  access-list 100 remark = NAT Route - Map DSL-1 LCA =-

  access-list 100 deny ip 192.168.100.0 0.0.0.255 192.168.40.0 0.0.0.255

  access-list 100 permit ip 192.168.100.0 0.0.0.255 any

  access list 101 remark = NAT Route - Map DSL-2 ABI =-

  access-list 101 deny ip 192.168.100.0 0.0.0.255 192.168.40.0 0.0.0.255

  access-list 101 permit ip 192.168.100.0 0.0.0.255 any

  Dialer-list 1 ip protocol allow

  Dialer-list 2 ip protocol allow

  !

  10 allowed DSL-2 route map

  corresponds to the IP 101

  match interface Dialer2

  DSL-1 allowed route map 10

  corresponds to the IP 100

  match interface Dialer1

  R2 config:

  ....

  10 VPN ipsec-isakmp crypto map

  defined peer Y.Y.Y.Y

  defined peer X.X.X.X

  game of transformation-VPN_TS

  match address VPN_1

  20 VPN ipsec-isakmp crypto map

  defined peer Y.Y.Y.Y

  defined peer X.X.X.X

  game of transformation-VPN_TS

  match address VPN_2

  ...

  Yes you can incorporate these underneath routes as well on track 2, however track 2 fails, you must have a failover to dsl1 itinerary, with highest should cost 100 road.

  IP route 192.168.40.0 255.255.255.0 Dialer 2 track 2 name VPN-1_to_R2_via_DSL-2

  IP route 172.20.110.0 255.255.255.0 Dialer 2 track 2 name VPN-2_to_R2_via_DSL-2

  Hope that helps.

  Thank you

  Rizwan James
  

  Post edited by: Mohamed Rizwan

• RV042 dual wan port forwarding challenge

  I have the latest firmware for this router. Here's what I want to do.

  WAN1 is connected to our primary ISP and has a static IP address. We pass a bunch of ports to our SBS 2003 for VPN server and the purpose of remote desktop. Redirect us P - FTP and FTP ports to another computer on the domain to use as FTP server, and we have access to this computer directly from our office as a mapped drive.

  WAN2 is connected to our secondary ISP that has a static IP address. I want to forward ports 80 and 443 of this connection to our FTP server (which has the internal IP address of 192.168.1.21) as well for this same computer can host our project Web site without needing us to get another computer that we would have to have in the office.

  This doesn't seem to be easily possible with the RV042.  I am open to any suggestions on how I can do that; I have another router I could throw into the mix if that would solve the problem.

  In fact, there to make a NAT on a public IP address to match an internal IP address of your choice.  I used the static IP address of the second internet connection and mapped it to our FTP server.

  The only downside is that the FTP server is no longer protected by the firewall, so I had to install a software firewall to protect it from the outside world ;-)