LWAPP could not reach WiSM WLC

Similar Questions

• Too many simultaneous downloads of image AP, AP could not reach

  friends,

  wonder if any of you have seen this before, you try to join a 1142 on a WLC_SRE version 7.4.

  the AP can ping the controller and vice versa.  In the graphical interface of controllers: monitor > Statisticc > join AP, I can find the mac of the AP which I am trying to be reached.

  the details of this show of mac:

  Last error: discovery request rejected Lwapp

  last is produced at the rate of error: too many simultaneous downloads of image AP

  Last join Timestamp:

  any idea where I can increase the threshold for this?

  I've tried probably once too often.

  Thank you

  Mate,

  Where are the outputs of the APs?

• Could not ping router RV042G public Internet address when it is after spending a SG200-08

  I use the optical fiber Singtel broadband server. I installed a SG200-08 for UNTAG VLAN to port 2 and connect the port to port RV042G WAN 1. It works very well with a public IP address. Access to Internet is very well to router LAN ports.

  However, I try ping on the public IP address of RV042G of the internet, I could not reach him. Everything what I'm missing in configuration SG200-08?

  Hello

  I don'i heard the switch block ICMP traffic as it has layer 2 switch, can you please check if the Ping on the interface of the router WAN is activate--> firewall--> WAN ping of uncheck block

  Please rate this post or marked as replied to help other customers of Cisco

  Thank you

  Mehdi

• Cisco WLC 2504 - Access Points do not reach the controller

  Hello world

  We bougth a Cisco WLC 2504 with two AIR-AP2702I-UXK9 Access Points. The problem is that the AP do not join the WLC.
  The output from 'show join ap stats' shows the following:

  (Cisco Controller) > view join ap stats summary all the

  Database Mac EthernetMac AP AP name IP address Status
  00:35: 1a: B1:A9:60 00:f2:8 b: f4:1 has: 9 c AP00f2.8bf4.1a9c 192.168.10.23 joined not
  00:35: 1a: C9:99:B0 00:f2:8 b: 77:b7:fc AP00f2.8b77.b7fc not joined 192.168.10.24

  (Cisco Controller) > show join ap 00:35:1 detailed stats to: b1:a9:60

  Synchronization phase statistics
  -For the synchronization request has received... Does not apply
  -For the synchronization completed... Does not apply

  Discovery phase statistics
  -Applications received discovered... 114
  -Answers success of discovery... 114
  -Discovery failure processing... 0
  -Purpose of the last unsuccessful attempt of discovery... Does not apply
  -Attempt to finally successful discovery time... 20:15:40.106 16 June
  -Discovery attempt ultimately unsuccessful time... Does not apply

  Join the live statistics
  -Join applications received... 57
  -Join sent successful responses... 57
  -Processing of the join request without success... 0
  -Purpose of the last unsuccessful attempt to join... Does not apply
  -Attempt to join finally managed time... 20:15:50.414 16 June
  -Join finally failed time... Does not apply

  Configuration phase statistics

  -Configuration requests... 114
  -Answers configuration successful... 0
  -Processing configuration failed... 57
  -Purpose of the last unsuccessful attempt to Setup... Invalid license in the application configuration
  -Attempt to finally successful configuration time... Does not apply
  -Time finally failed configuration attempt... 20:15:50.810 16 June

  Last the decryption of the AP details failure messages
  -Last message decryption failure reason... Does not apply

  Details of recent disconnection AP
  -Last AP connection failure reason... Does not apply
  -Last reason for disconnection AP... Unknown failure reason

  Latest summary join error
  -Type of error that occurred in the last... Application of configuration rejected LWAPP
  -Reason for the error that took place the last... Invalid license in the application configuration
  -Time which occurred the last error to join... 20:15:50.810 16 June

  Details of sign-out AP
  -Last AP connection failure reason... Does not apply
  Ethernet Mac: c 00:f2:8 b: f4:1 has: 9 Ip address: 192.168.10.23

  Would be grateful for the help.

  Best regards
  Marc

  Hi Marc,

  Make sure first that your controller has software code 8.0.x or above, if first better it. Here's the code recommended by TAC

  http://www.Cisco.com/c/en/us/support/docs/wireless/wireless-LAN-Controller-software/200046-TAC-recommended-AireOS.html

  Then, try the UX above deployment guide to begin. Under Advanced tab WLAN, you need to enable "of the first universal ap' in order to use this app provisioning & connect to the AP.

  If you have more than 1 AP, then you must start 1AP using this application. Other access points that you can feed them upward, while AP original is also powered, so they'll use protocal called NDP & start them automatically

  Let us know how it goes

  HTH

  Rasika

  Pls note all useful responses *.

• The URL you provided could not be reached. Please check that the URL is... Acrobat/SP2010

  The following error occurred in Acrobat when you try to click version history documents in SharePoint 2010. "The URL you provided could not be reached. Check that the URL is correct and that the network location is accessible. "The revision of the document is accessible, but through type HTTP via a web browser... but not through SharePoint <>== magic Acrobat X Pro COM object that works very well for currently extracted from documents. Please see image inserted. Reflections on a fix?

  

  Visitors have not been confirmed, but given the problem reports to is completed 6 months ago, it seems updated for the latest version of product fixes the issues.

• error report: ORA-20001: the print engine could not be reached because...

  Dear friends,
  I get the error report:
  ORA-20001: the print engine could not be reached because the URL is incorrect or a proxy URL must be specified.
  then click on the link to print the report.
  Print server the value-> advanced
  Protocol-> Http
  Host-> bieeserver
  The printing-> 7877 server port
  and the script->/xmlpserver/convert print server
  
  I'm sure that the settings are correct, but I get the error
  someone has an idea?
  concerning

  Hello

  No problem, happy to help.

  John.
  --------------------------------------------
  Blog: http://jes.blogs.shellprompt.net
  Work: http://www.apex-evangelists.com
  Author of Pro Application Express: http://tinyurl.com/3gu7cd
  AWARDS: Don't forget to mark correct or useful posts on the forum, not only for my answers, but for everyone!

• Installation of updates could not be completed after reboot

  I have a few updates. When I click on update, the full download and then they ask for reboot the device. When the beginning of the device running, they show the installation a message show bar "installation could not be completed try to update again...» "I try again but still the same problem. It's been like months I couldn't do updates. Help please!

  Hello A.MROUWEH,

  Thank you for reaching out to the Community Support from Apple. I know how it is important to keep your applications up to date and I have some information that can help. Whenever we see problems with updates and downloads of the app, it's a good idea to disconnect from the App Store by clicking on the Store menu and selecting "logout".

  Then, you restart the Mac and reconnect and see if it will download updates. If the problem persists, test the behavior in safe mode by following the steps in this article: try safe mode if your Mac does not start-up.

  Let us know if the problem persists. The entire community is here to help.
  Best regards

• Photo library could not be opened

  iMac with new 2 TB hard drive.

  OS X 10.10.5

  I had my hard drive replaced and you have a series of backups Time Machine on an external drive.

  After copying my library of Photos in the pictures folder, I opened pictures while pressing the Option key.  I chose the library I had copied from the backup, and a window appears with the message ' the library 'Library of Photos 2' with inconsistencies that need to be repaired'.»  I selected the button fix and repair began.  However when it reaches 95% complete, another message appeared. ' The library could not be opened.  Pictures has tried to fix the "Library of Photos 2" library, but cannot open it. '

  
  

  I also tried to select the library directly from one of the folders backup hard disk external and had the same result.

  Any ideas please.  Thanks in advance.

  How have you copied the photo library from the Time Machine disk?

  the library must be restored by entering the Time Machine. you do it in this way?

• Windows 10 could not locate the boot camp partition

  I'm trying to install 10 Windows on an iMac end of 2015 with a 512 SSD.  With the help of Boot Camp and an ISO of Windows 10, I am able to create the Bootcamp partition and the iMac restarts in the Windows of Windows installation. I enter my product key for my Windows 7 DVD and reach the screen showing partitions.  I select "disk 0 Partition 5 Boot Camp" partition and click on 'Format' according to the Apple support document.  The partition is then renamed to 'Drive Partition 0 5'.  When I select the next button, I get the following error message:- "we couldn't create a new partition or locate an existing one.  For more information, see the Setup logs files'.  The Windows Installer does not progress.  I deleted the partition several times using bootcamp and restarted the installation and always get the same failure.

  Any advice on how to install Windows would be greatly appreciated.  Boot Camp 6 will let me install Windows 7 on the iMac and so I need to use Windows 10.  I guess the Windows 10 ISO downloaded from Microsoft will work with the Windows 7 product key and Setup seems to accept it.

  Please, disconnect all external storage devices to your iMac and run the following two procedures.

  Reset the management system (SCM) controller on your Mac - Apple Support

  How to reset the NVRAM on your Mac - Apple Support

  and now try BC Assistant.

  See also Boot Camp: "we could not create a new partition or locate one" alert during the installation of Windows 8 - Apple Support .

• Error message Microsoft Word "Word could not create the work file. Check the amount of disk space on your startup disk. »

  I have a MacBook Pro, retina 13inch OS X el Capitan Version 10.11.1 with 16 GB of memory. It's brand new and I have recently installed Microsoft Word/Powerpoint etc. a disc that I bought a few years to my previous MacBook. It seems to work very well, but whenever I want to open a word document a message comes up saying "Word could not create the work file. Check the amount of disk space on your startup disk '. However, once I click 'OK' this message disappears and my word file opens without a problem. I have 16 GB of memory on this laptop and it's new I have not reached anywhere near the maximum amount of storage so I'm puzzled as to what this message means. How can I avoid that this message popping up everytime I open Microsoft Word? Any help would be appreciated!

  This has nothing to do with memory - it's the SSD. Word tries to create a temporary file to use as a backup if the program crashes while you are working. First, run the Microsoft Update program to see if there are updates you have missed. Second, Microsoft currently supports only versions 2011 and 2016, so if yours is older, you should consider the upgrade. Thirdly, I suspect that the temporary file is not get created so that you have fewer cancellations (maybe any) and that if the program crashes you have to restore.

• The host 'SMTP' could not be found. Please check that you have entered the server name correctly. _ subject 'Report issue', account: 'POP3', server: 'SMTP', Protocol: SMTP, Port: 25, secure (SSL): no, Socket error: 11001, error number: 0x800CCC0D

  The host 'SMTP' could not be found. Please check that you have entered the server name correctly.
  'Report issue', account: 'POP3', server: 'SMTP', Protocol: SMTP, Port: 25, secure (SSL): no, Socket error: 11001, error number: 0x800CCC0D.
  I'm answering an ad on craigslist and Windows Live continues to appear, but will not send my email I can be reached at * address email is removed from the privacy * or 614-499-1541.
  Thank you
  Stephen lawless

  Your post has nothing to do with Windows Update.

  You're not even close to have properly configured your e-mail account in Windows Live Mail.

  You will find support for Win7 e-mail Clients in this forum: http://social.answers.microsoft.com/Forums/en-US/w7network/threads

  You will find support for Windows Live Mail in this public newsgroup:
  http://www.Microsoft.com/communities/newsgroups/list/en-us/default.aspx?DG=Microsoft.public.Windows.live.mail.desktop

  Through your News Reader:
  News://msnews.Microsoft.com/Microsoft.public.Windows.live.mail.desktop

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Error message-""could not be achieved. " "The print spooler service is not running.

  Can anyone help. Whenever I try to print, I get a message that I need to add a printer, even if I have a printer installed. When I click Yes I Mindprint an another error box saying 'operation could not be performed. The print spooler service is not running"could someone advise how to solve this.

  Thanks in advance

  Matt

  Hello

  ·        Have you tried the steps that are listed in the article manually and see if the problem is resolved?

  ·        Who is the manufacturer of the printer and what is the model?

  ·        When did you get the error message when you try to install the printer or when you try to print?

  I suggest you follow the steps mentioned below.

   

  Method 1:

  I suggest you to check if the Printer Spooler service is started.

  a. Click Start and click Run.

  b. type services.msc in the box run.

  c. find the print spooler service and right click on it.

  d. click Properties and verify that the startup type is set to automatic.

  Method 2:

  Step 1:

  To start in safe mode, follow the steps mentioned below.

  a. restart and keep tapping F8 until you reach the start menu.

  b. Select safe mode and press ENTER.

  Step 2:

  In safe mode, delete the printer and spool driver files. To do so, start Microsoft Windows Explorer, and then delete all files and folders in the following two folders (where C: is the drive where you installed Windows XP):

  C:\Windows\System32\Spool\Printers

  C:\Windows\System32\Spool\Drivers\w32x86

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• The specified domain does not exist or could not be contacted.

  Last night I completely disconnected my laptop. This morning when I turned on the machine, she does everything as planned. When I reached the screen that requires a password to connect to Windows, the following error message came after I saw that my password and press ENTER.

  The specified domain does not exist or could not be contacted.

  I use Windows Vista Ultimate and the laptop connected to a wireless router.

  I tried to restart and stop several times. It did not work. I did a Diagnostic Windows memory check and it went well. Also, I restarted Windows in Safe Mode and some other modes and received the same exact error message.

  Thanks in advance for your answers!

  Dan

  Hello
   
  1. don't you make changes before the show?
  2. is the laptop connected to a domain or have you tried to connect to a domain?
  3. you have to any other user account on the laptop?
   
  If you have any other user account on the laptop, try logging in there and see if the problem still occurs. If you are able to connect, sever the computer from the domain. Try the following steps to separate the field.
  1. right click on computer from the start menu, click Properties, click Advanced system settings, the computer name, change, select workgroup and workgroup name type.  Click Ok. You will need the necessary permissions to perform this task.
  
  If the computer is not connected to a domain and you have not made any changes recently. Try to restore the system using Vista DVD.
  To run the restore of the system using Vista DVD, try the following steps.
  1. start in Vista installation DVD.
  2. choose your language settings, and click Next.
  3. click on repair your computer.
  4. choose your operating system and click Next. This should bring up the System Recovery Options.
  5. click on system restore.
  6. follow the instructions in the wizard to complete the task.
  7. once the system restore is complete, start the computer as usual and try to connect.
   
  For more information on the Windows recovery environment options, see this link:
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista
   
  Try the steps and post back with the results, so that we can help you further.
   
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• copy error: error 0 * 8007045D: the request could not be performed because of an i/o device error

  When copying the files, I get this error which is lower than
  an unexpected error prevents the operation.make a note of this error code, which might be useful if you get additional help to resolve this problem:
  error 0 * 8007045D: the request could not be performed because of an i/o device error
  filename DSc02828
  file type jpg
  size 3.27 mb
  updated the 09.11.2012
  try to jump again cancel
  Whats wrong here

  Hello

  Thanks for posting in the Microsoft community!
  You have reached the right forum for your question.

  1. don't you make changes on the computer before the show?
  2. where exactly you are trying to copy the file?

  Run check disk on the computer.
  a. click Start , and then typecmd.exe in the start search and then press ENTER.
  b. right-click on cmd.exe and clickrun as administrator.
  (c) in the command prompt, type the following command and press ENTER.
  Chkdsk /f
  Note: You may be prompted by a yes / no question. TypeYes and press ENTER.
  d. restart the computer so that the disk check starts. It will take about half an hour to complete the process of error checking. Do not restart the computer when the current disk check.
  Note: when running chkdsk on the drive hard if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost
  
  Summary the link:

  Error message when you try to perform a full backup on a Windows Vista-based computer: "the application cannot be performed because of an i/o device error."
  http://support.Microsoft.com/kb/952272

  Just reply with the results. I'd be happy to help you further.

• Error when sending to recipients CC: your message did not reach all or part of the recipeints

  When I send emails to recipients CC or BCC recipients, I get a message that says:

  Your message did not reach all or part of the recipeints

  The following recipients could not be reached:

  BUT IT DOES NOT LIST WHO DID NOT GET THE EMAIL. HELP PLEASE

  Hello Joanmary,

  Thanks for posting in the Microsoft Answers forum! In order to help us help you with your problem, please post back to let us know what e-mail client and web browser that you use.

  If you use Windows Live Mail, you can post in the forum below for more specialized assistance:

  http://windowslivehelp.com/

  Please let me know if this helps J

  Adam
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think