Mac Pro 4.1 - No. USB or bluetooth after El Capitan 10.11.3 updated

Similar Questions

• RAM Mac pro 1.1 detects only not all after kernel panic

  Hello

  my mac pro 1.1, 2 x 3.0 Ghz quad core, ram 24 GB os x 1.7.5 just had a kernel panic and stop, after being on for 12 plus hours for most sitting idle. When I restarted the mac pro, now he is grateful only 12 GB of ram on a lift and another elevator shows empty, the DIMMs are installed in mounting a 4gb4gb2gb 2 GB, riser board b = 4gb4gb2gb2gb =, are all matched pairs. all the ram has been installed and functional for the 7-8 months without any problem. This is the first time my mac has never stop from a kernel by itself, panic and he never failed to see half of the ram before, in fact it worked great for quite some time so far. I don't know what is happening and I hope someone can help me get this figured out and find a solution to this problem, thanks in advance.

  Bill

  You have a RAM failure.

  The Mac Pro features help Error correction Code RAM with hardware integrated with its Xeon processor. The Mac Pro 1.1 uses FBDIMM who get hot and do not have a long life expectancy. Work for 7-8 months does not work tomorrow.

  The error correction is used aggressively at the start, and all DIMM found to have errors during the Power-On Self Test brief execution have their slots declared 'empty '. This isn't an anomaly, these modules DIMM turns out to be BAD.

  If these modules DIMM is stickers from the seller, you can get replaced them under warranty of the seller.

  The kernel panic, you met just might be part of the same problem. You can find the report and review it and post it if you want.

  Mac OS X: how to connect to a kernel - Support Apple panic

  RAM problems show themselves as control panic machine, nucleus, often detected by more than one processor at a time.

• Bluetooth disabled after el capitan 10.11.4 updated updated

  I just did the mandatory update to the Version of El Capitan 10.11.4, my system now I have no Bluetooth available, everything Bluetooth hardware and services disappeared due to its update. Ideas please have correct?

  Yesterday, I had the same problem after the update. I fixed it by resetting the NVRAM as described here: How to reset the NVRAM on your Mac - Apple Support

  The only problem is: you will need a wired keyboard

• Mac pro 2 operating system upgrade

  I have a Mac Pro 2, here are the specs. My question is, why can't update OS X Lion

  Processor 2 x 2.66 GHz Dual - Core Intel Xeon

  Memory 4 GB 667 MHz DDR2 FB-DIMM

  Graphics  NVIDIA GeForce 7300 GT 256 MB

  Software  Mac OS X Lion 10.7.5 (11G 63)

  Because EFI computer is 32-bit.

  (144528)

• install el Capitan on no boot drive Mac Pro?

  I have a Mac Pro Tower 2012. I want to install El Capitan on one of my disks in storage so that I can switch from the boot disks. I think it would be easy, but I don't know how.

  Suggestions?

  Hello

  Paste the HD into a Bay in your MacPro.

  Open disk utility. Partition the disk.

  Be sure to only use the card Partition GUID and MAC OS extended (journaled) format

  You can choose to have the drive as one partition and then put el Capitan on it.

  Or you can have two or more partitions with El Capitan on one and use the other partitions

  anything you want. For example, I have a 1 TB drive that has three partitions, one for Yosemite

  one for El Capitan and the third for storage. Once you have configured your partion (s), quit disk utility.

  Now you are ready to install El Capitan, the installation program will ask you where you want to install the operating system.

  It can show you your original disk, but click on the button below "display more drives" this should display the disk partitions you created select one on your new drive and continue with the installation. "

• You can connect an Xserve RAID to a Mac Pro?

  I have a Mac Pro 1.1 successfully running under OS X El Capitan and OS X Server 5.1.5 and I was wondering if I could communicate an installation of the Xserve to increase productivity as Extra one SAS/NAS configuration if I added a Fibre Channel card or something.

  All this would be for a Mac-based (unofficial) Home Office / small business style setup where I have a few Macbook Pros/Airs data my desktop/Server central

  Basically, I want to know if it would be effective to use any sort of installation of the Xserve

  I've done some research more and I think that if the Mac Pro has a fiber channel card I could connect to an Xserve, but I guess there is a reason not to because if their was not would probably a more common thing

• Mac pro, USB keyboard not recognized at startup

  my mac pro (trash) is a wonderful device. Lately, however, it does not recognize a keyboard plugged in USB to start.

  I am at a loss to explain it. I need help.  Advice, anecdotes, guess wild welcome.

  my setup is like this:

  CENTRAL PROCESSING UNIT

  Monitor 27 "Apple (hub)

  Extended keyboard Apple USB

  USB hub (USB2, apparently, that was not what I paid for)

  Wacom Tablet

  Logitec mouse (no driver installed, Logitech *, but the mouse is great he is 15 years old)

  charger for Iphone

  beats headphones cable

  iMic USB audio

  The question seems to have started just after I took my computer to the site, when that happens, I use a keyboard and bluetooth mouse. I immediately told my mac to forget the keyboard and the mouse after bringing it back to the House. didn't let it go, there is no moments where he had 'speed' of any kind. Always moves in a bag built to waterfield.

  Model name: Mac Pro

  Model identifier: MacPro6, 1

  Processor name: Intel 8-Core Xeon E5

  Processor speed: 3 GHz

  Number of processors: 1

  Total number of cores: 8

  (By heart) L2 Cache: 256 KB

  L3 Cache: 25 MB

  Memory: 32 GB

  The system version: OS X 10.11.3 (15 d 21)

  Kernel version: Darwin 15.3.0

  L3 Cache: 25 MB

  Memory: 32 GB

  Based on my experience, your extended keyboard usb from Apple is the oldest plastic or the most recent aluminium? Based on which you have a branch above Apple usb extension cable. Anyway look at the end of the cable usb and it is most likely has that match unusual for her, this little triangle. It can fit on the Mac Pro USB, but can be a little bit loose as an adjustment. If you use a newer Apple usb extension on the older plastic Apple usb keyboard, this isn't a good fit. If you use the old extension of usb Apple on the most recent alum Apple keyboard, which is not a good fit.

  So low line trying to look at the adjustment of the end of the usb in the Mac Pro or hub or ver, you connect to. I got this problem which caused two problems: I was using the older usb Apple with the new Apple alum keyboard extension cable.

  1. frequently the keyboard did not react, looked dead

  2 - beta install for starting seeds would start on the hard drive to complete the installation.

  Given that I have "corrected" the usb extension appropriate keyboard usb Apple alum both problems went away.

• Mac Pro RAM, Audio, Bluetooth mouse problems

  I recently bought an Apple factory refurbished Mac Pro (end 2013) and replaced the three-chip RAM of 4 GB with 16 GB of Crucial two chips. Everything was great for the first two weeks. Then I started having a strange audio problem. Audio would become suddenly agitated. I disconnected and reconnected the speaker output and it would start working again. Finally, unplug the unit and plug the unit has stopped working (audio would eventually just stop working completely... zero sound with or without the speaker plugged in...) and I had to restart the computer.

  Then one day I noticed that only 16 GB of RAM showed up (I run own memory, so he's in my toolbar). I opened the machine and moved the two chips on the other side and when I rebooted, I got 32GB again.

  Then I noticed that when the audio problem came once again (he seems to be after the computer has been for a few hours or more) my Apple bluetooth mouse would disconnect and reconnect intermittently... ONLY when the audio starts to get restless again.

  I zapped the PRAM several times and now I get the 32 GB of RAM only after disconnecting the chips and MOVING them to another location, but not all the time. The audio port will begin to spoil, I reboot and I'm back to 16 GB.

  So, is it bad RAM? I removed a single chip and the audio problem still happens.

  Anyone have this problem? Apple Care suggested I bring it in the Apple Store, but I thought that I ask here before go this road, just in case there is a known issue.

  Thank you!!

  Rick...

  To establish if it is a RAM problem, remove 16Bb sticks and replace the original 4 GB sticks.

• You can add 3 USB to a Mac Pro (early 2009)

  My Mac Pro is still going strong. I have a 2.66 Ghz Quad Core Intel Xeon with 8 GB of RAM.

  Is it possible to upgrade to USB 3.0 on this computer?  If so - how?

  Yes...

  Compatibility

  • Mac Pro (with card slots) - OS X 10.8.5 + (compatible OS X El Capitan)

  https://eShop.MacSales.com/item/sonnet%20Technologies/USB34PME/

• 4.1 Bluetooth on an older Mac Pro?

  It may belong to another forum. I hope to be able to use a wireless headset for Bluetooth 4.1 with a 2010-2012 Pro 5.1 mac, which is not material BT beyond BT 2.0. El Capitan provide a software to allow BT 4.1 update, or do I have to get a dongle hardware or PCIe for her?

  Bluetooth 2.1 + EDR was built in Apple's HW on the mac Pro 4.1

  If your don't know to go to the

   > on Mac...

  System report

  Bluetooth

  the seller of the headset may be able to tell if the device works with 2.1 + EDR HW on your mac, as I KNOW the most characteristic of end of BT3 or BT4 won't work in lower versions of the receiver, but some other features may be fine.

• Mac Pro 3.1 dual port USB 3 pci-e card does not work on 10.8

  I have an inateck Dual Port USB 3.0 PCI-E card (KTU3FR - 2 p) which worked well when my Mac Pro 3.1 operated in the OS10.6.8, but after upgrade to OS 10.8.5, the map is no longer operational.   It can be seen as a device, but the description of the material says that he doesn't have a driver.  Inateck said it's Apple area, and "because of the new strategy of the Apple driver there is also no external support pilot in this case.  Can I do other than throw the card?

  THX

  Rob

  If inateck doesn't have drivers for OSX 10.8, and 3 Apple USB drivers do not work, then you are out of luck

• PCI 3.1 ASUS USB to the Mac Pro running El Capitan?

  Hello

  As the proud owner of a Mac ro 4.1 (updated to 5.1 and 2 X of Hexa-Core Xeon X 5670 CPU) I "suffer" a restriction.

  And it is now old and really slow USB 2.0.

  I would like to add a PCI USB 3.1 and I spotted the ASUS USB 3.1 PCI card.

  Of course, this card is given only as compatible with Windows...

  But I've seen a few reports of people claiming to have inserted this card in their Mac and have used successfully with several devices.

  It seems that these reports are under "Yosemite".

  I was wondering if they are always good with El Capitan...

  I put the card in the Mac.

  It seems to be recognized by the Mac Pro.

  In fact looking at the system information, under "PCI" give "Expansion USB card".

  BUT:

  -No USB key I have insert mounts;

  -No USB stick plug mounts;

  -my mouse lights

  -the keyboard does not work...

  So I'm wondering if:

  -El Capitan has got rid of the first USB support 3.1 to Yosemite?

  - Or if my card can be default somehow?

  -If this behavior can be caused by updates, I made (Mac 4.1-5.1 online) + 8-Core CPU-online 12 Core CPU?

  If anyone would be able to help me, I would be eternally grateful :-)

  If so, the card can be sent to the seller...

  Kind regards.

  FRED

  Hello

  Replying to myself: the card is functional.

  And the material is not at fault.

  How will I know?

  Simple: my Mac can dualboot on Mac or Linux Debian.

  So I just started in Debian on the same Mac Pro.

  Guess what? Without having to install any additional software, the card USB 3.1 is perfectly recognized under Linux.

  To remain decent, I will remain silent and will not say what I think Apple tries to limit the use of their devices without the need of technique to do so.

  I will now try to start to Yosemite to see if it allows me to use the card.

  Kind regards.

• ASUS USB 3.1 PCI card in the Mac Pro 4.1/5.1

  Hello

  As the proud owner of a Mac ro 4.1 (updated to 5.1 and 2 X of Hexa-Core Xeon X 5670 CPU) I "suffer" a restriction.

  And it is now old and really slow USB 2.0.

  I would like to add a PCI USB 3.1 and I spotted the ASUS USB 3.1 PCI card.

  Of course, this card is given only as compatible with Windows...

  But I've seen a few reports of people claiming to have inserted this card in their Mac and have used successfully with several devices.

  It seems that these reports are under "Yosemite".

  I was wondering if they are always good with El Capitan...

  I put the card in the Mac.

  It seems to be recognized by the Mac Pro.

  In fact looking at the system information, under "PCI" give "Expansion USB card".

  BUT:

  -No USB key I have insert mounts;

  -No USB stick plug mounts;

  -my mouse lights

  -the keyboard does not work...

  So I'm wondering if:

  -El Capitan has got rid of the first USB support 3.1 to Yosemite?

  - Or if my card can be default somehow?

  -If this behavior can be caused by updates, I made (Mac 4.1-5.1 online) + 8-Core CPU-online 12 Core CPU?

  If anyone would be able to help me, I would be eternally grateful :-)

  If so, the card can be sent to the seller...

  Kind regards.

  FRED

  Hello there Penguiner.

  Looks like you bought the ASUS USB 3.1 PCI card and questions about its compatibility with your Mac Pro. The following Knowledge Base article speaks to the maps provided by Apple which have been tested and work with the Mac Pro:

  On the compatibility between Mac Pro-carte models graphics

  Since the ASUS card is not listed, the reference of the article could be a good recommendation to follow:

  This article applies only to video cards that originally shipped with a specified Mac Pro or upgrade kit have been offered by Apple. Similar maps that are not provided by Apple may have compatibility issues and you have to work with this card provider to confirm compatibility.

  Thank you for reaching out to the communities of Apple Support.

  Kind regards.

• PCI cards with USB 3.0 or eSATA for a Mac Pro 2006 (1,1)

  Hello, Apple people!

  I got my hands on a Mac Pro 2006 earlier from a friend. I used it as a BESTIAL Server (seriously, this thing is not so much as breaking a sweat even when I throw it the more difficult task.) I love this machine) since I got it, and I think I want to do the updates. My plan so far is to get multiple mounting OWC to pick up the second drive Bay currently vacant DVD and install two 120 GB Samsung 850 EVO drives in RAID 0, while using the real HARD disk bays for a RAID 10 array (nested RAID: two RAID 1 arrays brought together in a RAID 0 array) of four 2 TB red WD drives and use two 250 GB hard drives currently in the machine in an external case in a matrix RAID 1 for backup. I'm pretty happy on this issue.

  My question concerns what interface to use for external drives of 250 GB. I can use:

  • USB 2.0 currently on the machine
  • FireWire 800 currently on the machine
  • a PCIe USB 3.0 card
  • a PCIe card with eSATA

  That we will get the faster speeds? I know that, theoretically, eSATA would get faster speeds (6 Gbps eSATA vs 5 Gbit/s USB 3.0 vs 800 Mbps, Firewire 800 vs 480 Mbps USB 2.0), however I know also (maybe?) that the Mac Pro I have only has grooves in v PCIe 1.1, with a (supposed) 250 MB/s maximum data transfer rate. would this bottleneck a PCIe USB 3.0 or eSATA card not worth?

  Note: don't worry all "Mac compatibility" with PCIe cards (or the table RAID scheme I mentioned). I am running Ubuntu Server (64 bit) on the machine, and given that the Linux kernel supports much more conductive than Mac OS X, I probably don't need to look at all the other drivers. This issue is specific to the hardware capabilities of the Mac Pro.

  Probably the most simple installation, you can do is to install the eSATA extender cable adapter.

• Hot synch not working, Treo 755 p, USB, portable, Mac Pro computer even with the reverend installed 17 "and allow the other applications preference checked HotSync

  Hello

  I'm a long-time Palm enthusiast who is frustrated.  No Palm products more for me or anyone I talk to until I fix this.  Someone at Palm should pay attention to their long-standing customers.  I bought Palm trees in 2002 and 2003.

  Documentation of support coming with two Treo 755 p I bought was so poor that never saw the fine print that there are three months of care, if I registered devices.  The registration page doesn't let me register.  All fields are ghosts after I put in the serial number.  I bought one in June 2008 and the other in early 2008.  If ever registered and can't get any help from Palm, now it seems.

  News issue problem is next to this referral below.

  I can't a Verizon Treo 755 p to USB cable Hot Synch with my daughters Mac Pro laptop 17 "laptop.  It uses OS 10.5 x she lives in another city so I'm wrong this shot from a distance.

  Fact - Between Revd Palm has been installed.

  PalmDesktopMac421Revd.dmg (17 MB)

  http://KB.Palm.com/SRVS/cgi-bin/WEBCGI.exe/, /? St = 4518, E = 0000000000255177998, K = 6239, Sxi = 3, case = obj (33...

  Advanced on the Treo to select in synchronization preferences settings allow other Hot Sync applications.

  That the process worked on my Treo 755 p Verizon as below:

  After a lot of work, hours over several months, I've had my my Treo 755 p Verizon hot Synch with an office of QuickSilver albums Mac running os 10.5 x.

  Have upgraded the RevD.

  Advanced on the Treo to select in synchronization preferences settings allow other Hot Sync applications.   Otherwise, the feature of wireless synchronization prevents a Hot Synch.

  Once these two were Hot Synch works very well, and sync wireless works fine and doesn't interfere.

  The wireless on both PDA's should be removed on the two Treo due the economy on 4 February, so I would like the HotSync to work so his Treo is saved.

  Many thanks to anyone who responds to troubleshoot.

  Best

  Works now, that she had created a user ID that you are prompted during the installation of the HotSync software, but he wasn't the same name of Treo 755 p.  The default ID is the one that it install the software, so he revealed nothing in addresses or contacts, but when she changed the ID Treo all his stuff was there.

  Message is about: Treo 755 p (Verizon)