Macros predefined for Simulator.

Similar Questions

• VeriStand "Custom Device" creation, including the different types of sources of code for simulation only

  Hello

  Before I ask my questions, I want to describe my problem:

  I would use VeriStand on a PXI system for simulation only. The simulation includes different types of sources such as Maltlab-Simulink-models, MultiSim SPICE models and code LabView for FPGAS-programming. Simulink models are available as a dll-file, generated with 'Real-Time-Workshop' and 'Simulation tool Kid. " They need to generate heavy duty, calculated by the modulation of the vector space and model the performance of a special converter. The MultiSim model will be transformed via a special VI in LabView code. I can generate code VeriStand (--> NI VeriStand--> Generate tools...). The PWM duty cycles of this dll matlab above are for LabView FPGA code entry. This will be the entrance of the gate of the tansistors of the MultiSim-model. Means, space vector modulation generates tension of the door and get the FPGA code to the ports of the inverter model.

  I am new in programming with VeriStand and LabView. I don't know how I can handle this. But NEITHER says it's possible. So my questions are:

  Is it possible to use VeriStand with more than one device Costum and simulate as a whole simulation. How can I associate different files.

  If this isn't the case, that I have to build a LabView Vi, where all the different sources of models are included.

  Is a walkthough or a user guide available, that I can use to fix my problems.

  I hope you can help out me. I need it for my bachelor thesis very fast. Thank you for your attention.

  Best regards Andre

  Here is a document describing how to create compiled LabVIEW templates and import them into NI VeriStand:

  http://www.NI.com/white-paper/12785/en

  The following link is a more general page describing several model and their support environments in NI VeriStand:

  http://zone.NI.com/DevZone/CDA/EPD/p/ID/6488

  Some additional modeling environments are supported, but not necessarily listed here since this is a growing list.  In addition, since NEITHER created a strategy of open model interface called NI VeriStand model framework, it would be possible to connect new types of sources of model in NI VeriStand without too much work.  Then the mapping tool, you found, makes the magic of easily to configure the connections of logical data between models.  You can also easily transfer each model to the individual processor cores, which contributes to the speed of calculation for system-level simulations.

• Should I have the APN settings for Simulator?

  Hello

  Im having problem when I run the Simulator application. IM using sybase platform for the development of BB and store when something in the im database get this error:

  Local port: 19780
  APN: "rim.net.gprs."
  APN username: 'null '.
  APN password: 'null '.
  There is no connection
  Information detected for 1 GPAK connections

  My question is what do I APN settings for Simulator?

  « ; deviceside = true' is a URL parameter - it is added to your URL.  Please search the forum, you will find 1 million references.

  Like this:

  www.Google.com;deviceside=true

  The AFN is defined either as a parameter added to the URL, or it is defined in the device options.

  Read this:

  http://supportforums.BlackBerry.com/T5/Java-development/different-ways-to-make-an-HTTP-or-socket-con...

• Visual Studio Plugin: Waiting for Simulator to complete loading... forever.

  Win 2K 3, Visual Studio 2 k 8

  I created a Web Site (does change all the files - just left default.aspx).

  Then I changed to browse with default for blackberry.

  Then I pressed the green button of debugging.

  Beginning BlackBerry MDS - CS has been rapid.

  Then it opens emulator "BOLD" BlackBerry, and after awhile, I clicked on 'Détails' on the dialog box 'start debugging '. This is what he had:

  [Start BlackBerry MDS - CS] From BlackBerry MDS Connection Services...
  [Start BlackBerry MDS - CS] FACT!
  [Starting Device Simulator] Launch Fledge: Throwing file - C:\Program Search Plugin VS9 Motion\BlackBerry 1.2\handheld\simulator_4_6_0\fledge.exe, settings - / app = Jvm.dll / Pocket = 9000/app-param = DisableRegistration/app-param = JvmAlxConfigFile:9000.xml/app-param = JvmDebugModeOff/session for partner = 9000/app-param = MdsDebugn/app-param = BrowserDebugPort:5557/app-param BrowserDebug =n/app-param = NoTutorial/Dungeon-lcd-on/pin = 0x2100001A/app - param = BrowserDebugPort:5557, skin - BlackBerry 9000, PIN - 0x2100001A
  [Starting Device Simulator] Waiting for Simulator to finish loading...

  The device was done loading some time ago and I can even open the web browser in Microsoft device emulator and go to bing and even my http://localhost:xxxx / website1, or whatever.

  Any ideas?

  I have only 1 network card.

  I tried with my firewall and turn off.

  I got further away now though.

  I realized that if I hit F5 and then launch and I click 'Cancel' and then go to Task Manager and instead of killing the user interface process that loads the emulator instead of this I close the RIM.NET.XXX or whatever the process.

  Then wait for the emulator to access the main screen then press on F5 again to join occurs but the emulator can't hit google or my local host.

  A companion of mine office has been able to operate its box with the same approach "kill process".

  It is running Win XP with Visual Studio 2 k 8 (without service pack 1 even if the requirements say it needs service pack 1)...

  Do you think its because my OS is Win 2 k 3?

  And why did kill Rim.Net process also?

• What is connection for simulated Ubunto servers information? TAC does not.

  Start the simulation on a server and try to connect.  No joy.  No documentation!  Support really miss on a purchased product from Cisco.  TAC said to try cisco/cisco.  OMG... they don't know!  So we are lead to believe that we can use the Ubunto 14.04 LTS server to generate the traffic.

  The username and password is created using the autogenerate option, or add you it as part of the #cloud - config in the properties. It's the same thing that add you a new router. Or you can provide the configuration before the start of the unit or use the predefined default values. For the router, it prompts you for the configuration, but for this image of specific pre-built Linux, you must set the user name and password.

  For example:

  #cloud-config
  HostName: Server-1
  runcmd:
  -Start ttyS0
  users:
  -default
  -gecos:
  lock-passwd: false
    name: cisco<=================>
  plain-text-passwd: cisco<======== >

• drivers for simulated devices of NOR-DAQmx (NI9211 etc.) in cDAQ9174

  I'm trying to understand the three methods of calculating the maximum analog input sampling rate below NI CompactDAQ system

  http://zone.NI.com/DevZone/CDA/tut/p/ID/4320

  Problem 1

  In method 1. Build your physical hardware system or simulate your configuration able & Automation Explorer (MAX) using NOR-DAQmx simulated devices

  Buy using my MAX, I was able to build a simulated chassis cDAQ7192, but the NI 9233 modules or 9215, and NI 9211 is not found in the MAX. do I need special disks for them?

  My MAX is verson 4.6.2f1 and LABVIEW2009.

  Problem 2

  Following the method 2 to use the NI CompactDAQ Advisor, 'Performance of analog to calculate' does not appear upward after you set up the chassis.

  Thanks a lot for your help

  Concerning

  Bing

  Your version of MAX and LabVIEW is not relevant. What is your version of DAQmx?

  After you add the chassis, you right click on it to select "set up simulated cDAQ chassis? I did this and was able to select all the devices you mentioned.

• Sampling frequency of HAVE is incorrect for simulated ENET-9213, WLS-9213, and USB-9213

  Hello

  ENET-9213, WLS-9213 simulation and devices USB-9213, I'm able to correctly get the sampling frequency of I = 1351 samples/s using DAQmxGetDevAIMaxSingleChanRate, which is incidentally on the value of spec'ed of 1200 s/s.

  However, when I create a task and add a voltage channel and then HAVE the sampling frequency of the task of query, I get a sampling rate of only 9 samples/s. I tried the same code with other devices and I get the sampling frequency corresponding to the device data sheet, it seems THST this problem is limited to 9213 devices.

  Why sampling returned by the task using DAQmxGetSampClkMaxRate rate returns than 9 s/s.

  And why the rate of conversion of DAQmxGetAIConvRate only 18 s/s.

  I enclose the test code which may be used to reproduce this problem.

  Kind regards

  whemdan

  The MathWorks

  Hello

  When I tried this with a USB-9213 simulation, I used the Sample clock Max Rate, as well as the Rate.vi of AIConvert:Max property node.  I could see that for 1 channel, I could spend up to 675.67/s, and I couldn't for 16-channel get79.49S/s (which total is equal to 1271 S/s, which is in the specifications).  The multichannel and single channel, I could get an AIConvert Max Rate of 1351.35.

  Something that could happen is that you do not explicitly set this device runs in mode high speed.  You'll want to set the property Get/Set/rest AI_ADCTimingMode channel at high speed, and you should see much better results in this way.

  Something else to note - I use DAQmx 9.0

• Construction for Simulator on OSX Lion problems

  After you have installed the NDK BB10 - without errors or problems with installation - I tried to build a simple Hello World application under Mac OS x Lion

  When I build it for a device, it compiles and connected correctly.

  When I set the config to build active Simulator, everything compiles properly but I have several errors from the linker:

  Examples of errors:

  / Developer/SDKs/bbndk-10.0.4-beta/host/macosx/x86/usr/ntox86-ld: could not find lQtDeclarative.

  / Developer/SDKs/bbndk-10.0.4-beta/host/macosx/x86/usr/ntox86-ld: could not find lQtScript.

  (And so forth, for six or seven more libs)

  These libs are present in x 86 form, under the x 86 target directory.

  I have to manually configure the path of library for mac / x 86? And if so, how? I went through all the options I can find for the project/workspace, and about I see the parameters to change the include path, I've not found anything for the lib path.

  Any suggestions are appreciated.

  I had this same problem and found that it was caused by a persistent qmake variable called QNX_STAGE

  I could check by running this command:

  /Developer/SDKs/bbndk-10.0.4-beta/host/macosx/x86/usr/bin/qmake -query QNX_STAGE
  

  and the new BB10 has one of its basic build conf files (/ Developer/SDKs/bbndk-10.0.4-beta/target/qnx6/usr/share/qt4/mkspecs/common/qcc-base-qnx.conf) using the value of QNX_STAGE in the construction (which mine was a few previous false installation of Qt)

  I was able to remove the variable by running this command and then everything worked afterwards:

  /Developer/SDKs/bbndk-10.0.4-beta/host/macosx/x86/usr/bin/qmake -unset QNX_STAGE
  

• How can I return my default styles for simulation software?

  While trying to remove a custom style I have some successful how to remove the default styles provided with CS9 (even if I hit Cancel).  Now when I try to put in place the style for a software simulation settings I have all of the options and if I click on create new the software crash.  Same thing happens if I click on restore by default.  The software has been uninstalled and reinstalled, but I still have the issue.

  All styles (master slides and skin) are in a theme. What theme are you using? There is no "styles by default', each topic has its styles. Can you be more detailed? If you speak one of the themes included with Captivate, you work with those stored in the Layouts folder in the assets of e-learning in the Public (Windows) or shared documents (Mac). This file is a copy of the original file that you can find in the subfolder layouts in the gallery under the installation folder. You can return to define an original theme by copy/paste to this public folder that I pointed out. If you want to reset all of the original themes included with Captivate, you can also close Captivate, delete the Layouts folder in public documents (NOT in the gallery) and when you open copied CP a new folder will be created in the public documents with all of the original themes.

• HAVE sampling frequency is divided by the number of channels + 1 for simulated ENET-9213, WLS-9213 and USB-9213

  Hello

  In the code in the example attached, I create a task with a single channel of AI.

  I get the maximum sampling frequency using DAQmxGetDevAIMaxSingleChanRate (or DAQmxGetDevAIMaxMultiChanRate), both return the same value of 1351 s/s.

  When I try to configure the sample calendar using DAQmxCfgSampClkTiming at the maximum sampling frequency clock he does not accept the rate and returns the following error. Note that the error message shows 2 channels, even if only a channel has been added.

  OUTPUT:
  DAQmx error:
  Sampling frequency is greater than the maximum sampling frequency for the number of specified channels.
  Reduce the sampling frequency or the number of channels. The increase in the conversion rate or
  reduce the time of the sample can also mitigate the problem, if you define one of them.
  Number of channels: 2
  Sampling rate: 1.351351e3
  Maximum sampling frequency: 675.675676

  Why the device driver thinks I have 2 channels in the task, when a channel has been added?

  Please find the code to reproduce this problem attached.

  Kind regards

  whemdan

  The MathWorks

  Hello w,

  By default, the ENET/WLS/USB-9213 in NOR-DAQmx module has the AI. AutoZeroMode the value of the DAQmx_Val_EverySample property. This causes NOR-DAQmx acquire the channel of the internal path of the unit (_aignd_vs_aignd) on each sample to return more specific measures, even if the operating temperature of the device moves over time. If you need the sampling frequencies higher than this allows, you can call DAQmxSetAIAutoZeroMode(..., DAQmx_Val_Once) (who acquires the formatting string when you start the task) or DAQmxSetAIAutoZeroMode(..., DAQmx_Val_None) (which disables the setting entirely).

  Note that for measures by thermocouple with cold junction compensation sensor of the 9213 NOR, NOR-DAQmx acquires channel built-in CJC (_cjtemp) on each sample as well, for the same reason.

  Brad

• Macro lens for Nex - 3n

  Hello world. I'm new in the world of photography, and I don't know that much about the specifics of the cameras and lenses. I have a Sony Nex - 3n and I want to buy a macro lens to use with it. I'm confused about what will be and cannot be inserted. If someone could help me it would be greatly appreciated I don't want to spend a lot of money only to find out the lens does not fit.

  With the help of the SAL - 30 M 28 will require the use of THE-EA3 or LA-EA1 lens mount adapter because this lens is a lens mount. The SALT-30 M 35 is a macro E mount lens that does not require the use of an adapter when it is attached to the NEX - 3N.

  If my post answered your question, please mark it as "accept as a Solution.

• How to increase the red box Captivate for simulation software and the video demo?

  Hello

  Can someone let me know if there is a way to increase the size of the red zone. As you can see on the screenshot, even if I chose "align the window' the red zone is not able to cover the whole screen I want to capture. I checked the Adobe help site https://helpx.adobe.com/captivate/using/record-software-simulations.html and looks like I could pick screen or application and there area, customize the size, but I do not see these options in my Captivate. I would be really grateful to everyone who looks at this problem! Thank you!  

  

  Yes, you will need to save this as a separate file, nationally (with loss of quality, always!) this project at the same resolution as the current project. After that, you will be able to copy and paste slides recorded to the existing project. The pages that you were talking about were on a new software simulation project.

• sending an email that is predefined for a user entry

  Hi all

  I created a flash game. When you're done playing we would like to invite the user to share the site with a friend. We have designed an email that will be sent to the e-mail entered on the site. I searched the forums, but did not find what I'm looking for. I don't want to send a message from a text field or entry form Flash, I want to send a personal message to the e-mail address.

  I wonder what kind of Action Script or other programming languages (server side) are involved in something like that.

  Thank you!

  Flash is not able to send an email directly.

  What you need to do is set up a server to send this e-mail and script to take input of the flash for the address and anything else created by the Flash.

  Depending on your server, the script language on the server side is different.

  In regards to the Flash side of things, take a look at the LoadVars class, specifically the function SendAndLoad.

• What choice for Simulation software w / multiple windows

  I usually choose the option of application for registration. But in this project, I have to open the windows Explorer and select files as part of the sim card. What is the best option? Are there best practices? The main thing I watch takes only a small part of the screen so I don't want to choose the mode full-screen. Thank you!

  What version of Captivate work? I begin with an "empty project" with the desired dimensions (e.g. 800 x 600), her drag start and then insert record gliding (choose if possible an application window to save, snapping to the determine the dimensions). Save only the slides for the current application window, e.g. Windows Explorer. In case you use CP4 Finally you can choose and use a panoramic mode. Then you stop recording, to possibly prepare a slide of instructions and save another pile of slides in another window.

  I hope you understand a bit what I try to explain: this split of record slides easier sometimes. Feel free to ask questions if you want to try this method.  Just trying to help, Lilybiri

• How to make my waveform in the simulation design and control work continuously?

  Hi all, I m a begineer to Labview and have a few question.

  I use the Labview to design and implement a controller for FOPTD system, but I found that the waveform in the 'loop control and simulation"does not work continuously. I mean keep repeating in the same graph from 0 to 10 seconds. Is there an approach to make it run continuously?

  Thank you very much.

  Whenever a loop Control Design and Simulation is executed, it connects a full simulation, the initial time for the last time. When you drop a new loop CD & Sim down, the default values are zero second initial time and 10 seconds for the last time. I guess what you probably want is for simulation do not stop at 10 seconds. Double-click the left node attached to the CD & Sim loop and extend the end time. You can change the end of 'Inf' time if you want it to run until the VI is stopped.