manage web lvm

Similar Questions

• The proSafe (JGS524E + GS116E) Switches: Configuration Management Web GUI in VLAN specific

  Hello

  I use a JGS524E and a GS116E. The two are connected via a 802. 1 q uplink with all defined VLANS in him.

  A 802. 1 q other interfaces goes to a pfsense firewall, which serves as a router and dhcp server for each VLAN that I use.

  How can I configure the switches plug are in one VLAN specific and get his IP address of the dhcp server in this VLAN?

  At present, it seems to be random access: it is not predictable that range from intellectual property, it takes its IP configuration via dhcp...

  How management function works internally?

  Thank you

  Markus

  Hello

  Thank you. I tried it out, but the behavior seems to be a little different:

  I configured a static IP address for the switch (10.1.0.13 / 24). I have access to the switch web gui via the ip address of the host of a host directly connected (connected via a trunk port, where I put 1 VLAN on the trunk), but it is all the same, what VLAN that I use:

  When it is connected to the VLAN 1 I have access, but also through 10 VLANS, VLAN 20 and so forth (assumed, I configure my computer appropriate staticly in the IP network, for example 10.1.0.20 / 24). So it seems not be limited only to the VLAN 1. You have access to each vlan, only the IP configuration must be in the same network.

  I'm not sure, how it behaves when cascading the two switches, I have not tried.

  If this information can be useful for other users with the same question about this switching product line.

  For me, this behavior is not very well implemented from my point of view. For security reasons, you must limit access to the administration, for example by allowing access from a specific hardware port or a vlan. With the effective implementation, centralized management for a cascade topology is not easy to set up, perhaps because the behavior is not very clear and not documented in the manuals.

  Mentioned on the edge: there is no available TLS/SSL encryption when accessing the web gui (not https). So the password is transmitted in clear text... not a very good idea, I think.

  Thanks a lot for your help.

  Best regards

  markusd112

• Management Web Dell Force10 S series S55

  Hello

  I would like to know if there is a way to enable web management on a S55 dell force10 switch.

  Thank you.

  The S55 Force10 has no web management.  You must use the CLI or SNMP.

• Can not manage Web sites on the Cloud Creative

  When I try to manage my websites on the cc Web site it goes to a page saying "Page not found sorry, we did not have this page.". When I try to log in BC Site areas I get "ERROR: the web site you want to administer is not found." Is there something wrong with my setup? He has always worked until now.

  Are you going to http://creative.adobe.com, I can access that.

  Could you please try another browser and also try to clean the cache and browser history.

  -Thomas yannick

• Managing Web only in VM Server 2?

  Version 2 is managed by Web only?  If it is a client based on the management console, could someone provide me with instructions on how to find it?

  Thank you.

  Rory Schmitz

  You can install the VI Client.  Download from your VMware Server - folder C:\Program Server\hostd\docroot\client\ VMware host.

  Robert

• Where to manage Web Oracle Conference?

  Hello
  
  I installed the Suite of Oracle collaboration for the first time and I have to configure Oracle Web Conferencing. I can't find Console I can manage Oracle Web Conferencing.
  
  After installing Oracle Collaboration Suite, I can only find Application Server Control Console. I went through this Console, but in this Console, I could not find Web conference options.
  
  Please tell me I can open this link to set up conferences to the Admin of the site Web and also tell me what I need to download client tools for web conferencing etc...
  
  How can I check if Oracle Web Conferencing is installed on my system or not?
  
  I need to download components seprate Web Conferencing etc.?
  
  Please help me and answer me soon. Would appreciate the instant answer...
  
  
  Kind regards
  Saami

  You should:
  -first to enroll a user as an administrator (Administrator of the company)

  http://download.Oracle.com/docs/CD/B25553_01/RTC.1012/b25460/postinstall.htm#CIHDBBFF

  -and then to connect to OCS Webconf with this user

  With all that you follow, you should drop a look on Administrator's guide OCS Web conf

  Kind regards

• Storage Manager Web site gives no sites

  Lately the webadres for all settingsmanagers has been changed from macromedia to Adobe.

  As this changes not visited Web sites are visible in the Web site recording settings panel ( http://www.adobe.com/support/documentation/en/flashplayer/help/settings_manager07.html ).

  This means that the flaschcache is now empty automatically or is there a faulty connection due to which the flashcache is not reachable for a household?

  Or maybe something else is the question?

  INFORMATION SYSTEM
  Your Flash Version	13.0.0.214
  Name of your browser	Firefox
  Your operating system (OS)	Windows (XP)

  Well surprisingly enough the macromedialink works again...

  http://www.Macromedia.com/support/documentation/en/flashplayer/help/settings_manager07.htm l

  The Adobe link I mentioned in my first post still gives a bad view.

  But for now, my problem is solved.

• How do I watch videos in Creative Cloud File Manager (Web site)

  I recently downloaded a .mov on my creative cloud. Is it possible that I can watch this video on the site without downloading? Do I need to encode the video in a certain way.

  If this is not a function, it should really be.

  Currently, there is no video playback. We had other clients to request this feature and it will be considered for a future version.

• Web management interface of LAN N3000

  sHello,

  We have replaced our old 62xx powerconnect with a new stack of switches N3000.  With the earlier material, there is no remote management interface. Thus, we were able to manage the passage of our LAN subnet.

  If I put interface OOB in our LAN subnet so I can't send IP to the VLAN. ... .

  How to be able to administer our N3000 switch via web gui of our LAN subnet.

  I tried to address ip configuration for vlan1 in the hope that I would be able to gui for managing web... .but not...

  Console >Activate

  Console #Configure

  Console (config) #interface vlan 1

  Console #ip 192.168.0.250 address 255.255.255.0

   

  Can you please help?
  

  Thank you for reading my post.

  Gmiga.

  recently had this problem,

  you don't need the OOB port so just set his IP and the gateway to something, that you'll ever need (or just leave no configured completely make sure you it is disconnected/disabled)

  what you were doing with the VLAN is correct, simply set the gateway:

  Console > activate

  Console #configurer

  Console (config) #interface vlan 1

  Console (Config-if) #ip address 192.168.0.250 255.255.255.0

  output console #.

  Console (config) #ip - default gateway 192.168.0.1

  by setting the default gateway, you should now be able to administer your switch to other subnets

  You may have already worked to this point, but it is good to leave it here for others.

• Financial falied to application Web data quality management (FDM)

  Hello

  I just installed Foundation, CM, LDCS, R & A (Server1) Essbase (Server2) HFM (Server3) planning (Server4) FDM (classic) and DRM (Server5) in a distributed environment. configuration and everything went very well no problem. How ever when I try to access the web application FDM that nothing comes, I ran the diagnostic report in the Foundation and FDM Server and I get below error. I tried relative to setting up web application Server FDM and re configured the Web server and logical address on Foundation.

  Don't know what I'm missing here from point of configuration, if anyone can guide me in the proper papers or suggestions would be greatly appreciated

  Foundation:

  FAILED

  HTTP: HTTP

  Check availability of HTTP context http:// < FoundationServer >: 19000/HyperionFDM Error: Codes bad response with the GET and POST methods both: 404 and 404 Recommended action: Check that the application is started

  FDM:

  FAILED

  WEB: Web Application

  The availability Web application context http:// < FDM Server >: 80/HyperionFDM Error: Codes bad response with the GET and POST methods both: 404 and 404 Recommended action: Check that the application is started

  Thanks for any help

  Thank you

  So, if you go to http://fdmwebserver/HyperionFDM , then you get a 404 error?

  Are you sure that all the FDM components have been set up outside the EMP Configurator for example config Manager web, Application Server Config Manager, Configuration of load balancing

  The HyperionFDMAppPool was created, it is started, is IIS running ok, if the HyperionFDM has been created can see you in IIS

  See you soon

  John

• vCenter 5.5: Web services management service could be started or ended unexpectedly

  Hello

  in our vcenter costs installed 5.5 (on Windows 2012r2), we are not able to start VMware VirtualCenter Management Web services, we have a lot of messages in the system log:

  "The service of VMware VirtualCenter Management Webservices ended unexpectedly.  He did this 874 times.  The following corrective action will be taken in 60000 milliseconds: restart the service. »

  We only found KB articles for vcenter 4.x or 5.1, many said look if any other process is using port 8080, we checked it... no other process using this port

  Any suggestions?

  OK, found the problem: it isn't Port 8080, it is the port 8009 that causes the problem. We had installed qlogic HBA Software (QConvergeConsole), which has installed its own tomcat server. It blocks the port 8009.

  found in wrapper.log

• How update you the Web/API/CLI password in the NSX Manager?

  I looked at several places and not seen how change the password to directly access the NSX (and not through vCenter) Manager:

  • NSX 6 Installation and Upgrade Guide.pdf
  • nsx_61_api.PDF
  • The NSX Manager CLI itself (in mode privileged or not)
  • configuration of the NSX in 'Networking and Security' Manager vcenter (a long shot)
  • The NSX Manager web UI

  Is there a way to change this?

  It should work with:

  Enable

  con t

  password CLI

  write memory

  (just tested with NSX - v 6.1.2)

  I think your order is trying to recreate the admin user.

  See you soon

  Richard

• vSphere Web Client sucks so bad that my management experience and by supporting VMware a turn at the SH *!

  Purpose of this post is simple and obvious... bring heavy customer development.  Thank you!

  Arrogance is a form of ignorance.

  Unfortunately, the web client has made my job satisfaction.  I was once nothing more than a MCSE certification and grew to hate the hours and hours of late night windows supports windows recovery until hours early in the morning, wait too long so that it recharges etc etc...

  My first implementation of vmware was in 2004, and from there I made my career goal and never looked back, almost double my income in a few years, with great joy in the management of a new and exciting technology that has made things easier and more efficient.

  SUDDENLY the vmware customer management web stole me this, and many others.  They don't understand the magnitude this Act horrible sh... t is having on the "practicality" of technology management.  It is terrible and downright insulting.

  VMware - you claim that your product introduced efficiency in the form of op ex.  take down and or change any web page and marketing publication showing your product makes it easier and more efficient, it is simply no longer the case.  You yourself have sabotaged and sabotage the future of your growth thanks to the bad decisions and arrogance.

  anyone HE mocks you now while you sit with arrogance and dilute yourself with thoughts of leader in a new era.  Smart people are not lead with arrogance and bad decision-making and especially not by the release of the product of bad design.   You're stumbling block big time, the writing is on the wall.

  Difficulty the fiasco, for the good of all.

• Web pages do not show in the BusinessCatalyst site manager

  Hello

  Even though I have a marketing plan of catalyst for the company, in the site manager web pages don't appear. They do but in another site hosted under the Web marketing plan.

  How this can be solved?

  Thanks for your help.

  Kind regards

  Peter

  Yes it can.

  I had a discussion with the Helpdesk of BC and guess what? Just click a box and you're done!

  All right, we ask?

  Well, connection via admin to your web page of BC.

  Then, in the top right click on your name and go to 'my account '.

  Scroll to the bottom for a little less 'my existing password' there is a box with the description

  'enable editing for content (incompatible with muse) online.

  Click this box for online content editing is enabled and you're done.

  Two suggestions to the technical team of Adobe:

  1. it is - due to the development of adobe - compatible muse muse, as changes in online content can be merged with muse on choice of the web designer. So the extra (incompatible with muse) is not quite real today

  2. it would be useful if an exclamation mark next to the 'site manager' arises when you see all of the elements as, due to the activation of the option in your account.

  Then it's as simple as that!

  Kudos to you all.

  Peter

• LabVIEW Web Services: How "undeploy" web services

  I created the example of web services:

  Address book in book labview\examples\comm\webservices\address project for an example of a Web service that handles to publish data, streaming output, static content and HTML Forms.

  Weather project monitor labview\examples\comm\webservices\weather monitor

  for an example of a Web service which publishes simulated weather statistics.

  Using the generator of the user Web interface, they are still included in the list of available web services when I import Web services.

  How can I get rid of them?

  My OS is Windows Server 2003

  C:\Documents and Settings\All Users\Application Data\National Instruments\WebServices\aws

  Has been able to manage web services via the System Manager.

  Thank you