Web management interface of LAN N3000

Similar Questions

• PowerConnect 2824: Can't access web management using VLAN TAG 1?

  Let's say I have port 20, which is a member with LABEL of VLAN 1, 10 and 20.

  If I try to access web management to help interface VLAN 1 TAG, it is not accessible.  However, if I remove the tag VLAN (and the default PVID value of 1), then it works fine.

  Is this a known limit?

  In addition, change the management VLAN on my 2824?  (what I read, it is not possible)

  You're right about the two statements.  The Web GUI is accessible only through the untagged VLAN 1 and it is not possible to change the management VLAN on the 2800 Series switches.  On the other upper level switches, you can use the ip address command vlan xx to move the management VLAN in the VLAN specified in the statement.

  I hope this helps.

• UCS management interface - B series

  Management of the UCS of series B can then passage to uplink ports / Server interconnection fabric and not on the Management Interface of the FI? As in the C series there is a choice in the MMIC where management requires ports LAN (LOM)

  Yes, since IF you have a connection of the mgmt0 port - is for the FI management and KVM blade, etc. (e.g. the OOB management).

  On the IF configure you uplink profits that are used to carry network traffic on the blades.

  On the C series if you configure the port MMIC to be mode shared-LOM then yes all traffic management and the path of data will be done by the same ports LOM. If you choose the dediacted port then you must use the MMIC port on the C series for the management and LOM for the data.

  . / Afonso

• IDS 4215, good place for an interface sniff (LAN or DMZ)

  I have this sensor with two interfaces only at work, I was asked to check that

  See the IDSWORK version #.

  Application partition:

  The Cisco Systems Version 1.0000 S47 Intrusion detection sensor

  2.4.18 - 5smpbigphys-4215 OS version

  Platform: IDS-4215

  an interface that is Ethernet 0 connected to switch in the DMZ, and 1 Ethernet connected to switch 4005, logically I have to monitor DMZ not switch box 4005 (since I had only two interfaces, my case), I'm right?

  That means that ethernet 0 should be to sniff (surveillance) since it is connected to the DMZ and interface 1 for command and control, since it is connected to switch 4005, but according to cisco specifications

  http://Cisco.com/en/us/products/HW/vpndevc/PS4077/products_configuration_guide_chapter09186a008055df7d.html#wp1051279

  Table 5-2

  FastEthernet0/0: Interfaces supporting VLAN pairs Inline (port detection)

  FastEthernet0/1: Interfaces do not support Inline (command and control Port)

  Note: Cisco has mentioned FastEthernet, one I had Ethernet, makes all the difference?

  Because I did not have this configuration, he made by another, should I change this?

  It seems that your credentials are equipped with the basic ports (2 x Ethernet) with E0 C & C port, while E1 is followed by port.

  BTW, Ethernet/FastEthernet ports are in fact the same.

  To monitor your DMZ segment, then place the E1 in this segment, as E0 on inside segment where in addition to directing the Manager of its web management or CLI interface box, you probably can use basic VMS that comes free with it.

  And since you have dedicated switch to host the entire DMZ segment, you can easily monitor box (SPAN) all and send all traffic to the IDS.

  If you need to change the configuration, you may need to test at least to verify signatures is enabled/disabled and pc/mgt host is allowed to access the box and so on. But it is a good practice for audit and review the new config/setup, as it is a security zone, you need to do to monitor trust and you talk about all the possible threats, attacks or violations.

  HTH

  AK

• WLC use Management Interface & more get started Questions

  Hello

  I am yet to implement Wireless LAN in one seat of our customers. There are 40 x 1130AG LWAPP AP and WLC 4404 with ACS 4.x for authentication of Wireless Clients attempting to access the LAN.

  For the WLC to connect to the Dual Core Switch, I need to use only a Management Interface with port 1 being the main and mapping Distribution system the DS 2 Port as the backup for the Management Interface port. Is this correct? or can I have configure dynamic Interfaces as well. Is the interface of access management / management and configuration only? Management interface will communicate with ACS for AAA and AP who wish to associate with the WLC, is this true?

  Note: WLC, AP, Wireless customers & AP are in the same IP subnet.

  Some other question of WLAN is so it helps me during the implementation.

  Can • I use the 802. 1 x authentication applications saved in Windows XP for the Wireless Interface; instead of the Client Application from Cisco. For this purpose; I have to configure the WLC / Wireless Client use EAP algorithm; is that correct?

  • With the help of MRR, interference between of multiple (3-4 AP) AP in the same area is controlled by the WLC by changing the channels used by the AP, that isn't even on of the AP is it good?

  • How many users Client will connect by channels. 802.11 a / g will provide 11 channels, it is right?

  • I'm putting in the WLC to limit client connections by AP to 25, can this be achieved?

  Please, can someone help me calrifying the points above.

  Kind regards

  Keshava Raju

  Unless this has changed recently, you can't. The ports must be then break into individual groups. You can the controller mode layer 3 as Cisco is the support Layer 2 stop. The Director of the PA is necessary in all cases in LWAPP layer 3 transport mode. Do a search on Cisco.com to the configuration guide for the version of the code you are running. This will give you a step by step installation instructions.

• WLC 7.4.121.0 configuration management interface

  Hello.

  I have a problem Management interface IP setting in new 5508 controller. I get the error "error in the management interface IP configuration". I can't put a management controller IP.

  Start IPv6 Services: ok
  From Config Sync Manager: ok
  Start Hotspot Services: ok
  Starting the PMIP Services: ok
  Starting the Services of Portal Server: ok
  Starting the mDNS Services: ok
  Start Management Services:
  Web server: CLI: ok
  Web security: authentication certificate Web not found (error). If you cannot access the management interface via HTTPS please reconfigure virtual Interface.
  License Agent: ok

  (Cisco controller)

  Welcome to the Setup Wizard Cisco tool
  Use the '-' character of backup

  You wish to terminate autoinstall? [Yes]: -.
  Invalid response

  You wish to terminate autoinstall? [Yes]: no

  Name of the system [Cisco_bf:dd:c4] (31 characters max):
  AUTO-INSTALL: process completed - no configuration not loaded

  Enter administrative username (up to 24 characters): admin
  Enter the administrative password (3 to 24 characters): *
  Administrative password: *.

  Interface Configuration for IP [static] [DHCP] address service: no
  The service Interface IP address: 1.1.1.1
  Service Interface subnet mask: 255.255.255.0

  Enable aggregation LAG (Link) [Yes] [NO]: no

  The Interface IP address management: 192.168.10.1
  Management Interface subnet mask: 255.255.255.0
  Router default Management Interface: 192.168.10.10
  Error in the management interface IP configuration

  The Interface IP address management: 10.10.10.1
  Management Interface subnet mask: 255.255.255.0
  Management router default interface: 10.10.10.100
  Error in the management interface IP configuration

  Address IP Management Interface:

  ····························································································

  Did someone in the face of this issue?

  Thank you.

  Hello

  Try these:

  1. with the WLC, please the Frother (in SecureCRT or hperterminal) the value none. Once the changes are made, CLI will start to work as usual.

  2. Another common reason may be related to the configuration of the virtual interface of the controller. To resolve this problem, remove the virtual interface, and then re - generate with this command:

  WLC >config interface address 1.1.1.1 virtual

  Then restart the controller. After that the controller is restarted, re - generate the certificate webauth locally on the controller with this command:

  WLC >config certificate generate webauth
  In the output of this command, you should see this message: Web authentication certificate has been generated.

  Now you should be able to access the secure web mode of the controller to restart.

  3. try to use a diff for the service interface IP address do not use 1.1.1.1.

  Concerning

  Remember messages useful rates

• How do the management interface of configuration of an ethernet interface?

  We have an ASA 5540 requiring a LAN port for failover. And the left side of the interface available only the management port. How do the management interface of configuration of an ethernet interface?

  You can disable the mode of management only on this interface to make as regualr routable port and use for other purposes, including the purposes of failover LAN database.

  On the management interface - 5510 but applies generally to the management0/0, itself including 5540

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/configuration/guide/intParam.html#wp1057800

  Basic LAN failover configuration

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/configuration/guide/intParam.html#wp1057800

  Rgds

  -Jorge

• ACS1121 MANAGEMENT INTERFACE

  Hi all

  I'm trying to configure the interface of management on Cisco Acs 1121. When I type see the race

  I can only

  Gigaehernet 1

  Gigaehernet 2

  Gigaehernet 3

  Gigaehernet 4

  but I can not able to see the management interface

  you know that if you see Cisco ACS back panel it has 4 X Gig interface and management 1. I would like to set the ip address on the management interface.

  Now that I have configured the ip address on concert 0, I can access ACS via Web interface.

  Do I have to update the IOS device ACS to configure Management Interface. Please answer as soon as possible. very urgent. Please see the attachment.

  because they are unable to make changes in the material each time, for the rest of the interfaces they are working on it (acs codes) and will put more functionality in the future codes to support the new feature using these controls.

  don't forget ACS 5.1 is very young, there are N number of new features is aligned for this product.

  HTH

  Regds,

  Jousset

  Note the useful posts ~

• ReadyNAS Pro 6000, no web admin interface

  Hi, I can not access the web administration interface of my SIN, all I get is a broswermessage saying "unable to connect", tried different browsers and factory reset have the device, without change.

  Any ideas on how I can fix this?

  Just got home from work sin, then there is nothing about this, just put in some old drives to see if she would go.

  Ping device response and I can get to the telnet connection.

  See that there is no data on this subject, you can try this:

  1. turn off the SIN

  2. connect the drives to your PC and delete partitions off them

  3. replace discs in the NAS and try another factory default.

• EqualLogic group member network configuration error: "management interface should not be on the san subnet.

  Hello

  We currently have new EqualLogic 6100 device with this network configuration:

  Director of the IP - 192.168.0.2 (VLAN1).

  Member network config:
  eth0 - 192.168.0.3 (VLAN1)
  eth1 - 10.10.10.3 (VLAN2)
  eth2 - 10.10.10.4 (VLAN2)
  eth3 - 10.10.10.5 (VLAN2)
  ETH4 - empty

  I would attribute 192.168.0.4 to eth4, but received the error: "management interface should not be on the san subnet.

  I am sure that all interfaces eth has access to the VLAN1 and VLAN2, mean error indicates that eth4 should not access VLAN2 and only access the VLAN1 on the switch?

  Or eth0 should also have access to the VLAN2 only to reconfigure eth0 and eth4?

  Thank you

  > The group eating IP should be in iscsi VLANS?

  Yes!

  Note: If configure you an EQL it will ask an iSCSI port because nothing is more necessary to bring it up. The doest previous EQLs have a dedicated Mgmt Port and later, you can convert the last ethX as a MGMT port. This is the reason why configure you ISCSI at the beginning. (Think of a mixed group of newer and older models, and you get a picture)

  OK... once again it is the one and only member of the Group and there is making the production host connected to the right?

  The change of IP address, to a 3rd. subnet for temporary use.

  -Do not touch eth0-3 and the IP address of the group now

  -Configure the MGMT port and IP address management in the tempr group. Subnet. Use the Config-> Adv. Group-> network MGMT. You can change the MGMT Port of the Member, and the address IP of MGMT

  -For the registration of the configuration, you will lose access. You must place your admin PC in the templ. subnet so

  -Connect to the GroupMgr with temp again. INTELLECTUAL PROPERTY

  -Now you can change the IP address of group 10.10.10..x

  -Now you can change eth0 10.10.10.2

  -At the end, you can change the address IP of the Group MANAGEMENT, as well as the MGMT Port to 192.168.0.x

  -Change the IP address of your admin PC rear

  A failover, you should consider to hang a serial cable the active controller of the EQL. Use 9600,8,1, N with your favorite terminal program (putty.exe on windows). All the steps, you can perform from the command line.

  If this group and the only member not in production, but you can reset the config and restart from the beginning.

  Kind regards

  Joerg

• There is a security risk to plug the internet router management on the LAN port?

  I have to install an ASR1001 on the internet for my business.  I noticed that the ASR1001 has a dedicated management port and I was wondering if it's a security risk to have this mangment port directly connected to my local network, so that I can mange it from my office.

  I want to only run the ASR of this port and I will no management through its public IP address.  Is it possible for a malicious user to compromise the router then have access to the network but this management port?

  I'd say it's a reasonable risk.  If you intend not to allow future management of the public side sessions you are a good start, implementation of protection against attacks.  Combine that with a few basic hardening, for example to disable source routing, directed broadcast, ip proxy arp, finger, as well as an ACL on the management interface so that all traffic from an untrusted interface on the router would be unable to receive return traffic.  In addition, the management vlan must be a dedicated vlan.  I would not fall in the same vlan in that your office is located.  Better design would be to fall into a dmz (acl on the router's management interface would be redundant in this case) and to apply the rules of the firewall.  However, if this is not possible, order access to routing on the ASR as well by including only a 32 road to your management station via the management VLAN interface.  Also, remove any redisribution or advertising of this management interface in your routing protocol.

• How to set up the AP Manager interface on vWLC

  Hello all,.

  I want to bulid a laboratory wireless env, vWLC is used, but I can't find where I could configure AP Manager interface vWLC.

  How do I creat an interface of the AP Manager?

  Thank you for your help.

  1.How many APs could this Dynamic AP Management support ?

  No limitation on the interface. It all depends on how can license AP you have on your vWLC

  2.We can't creat AP manager interface on vWLC like real WLC , right ?

  Yes, good. New platforms of controller, there is only the interface of management exist. There is no separate AP Manager interface.

   3.How can I distinguish my AP's  "Country Code"  ?

  If you look at your reference number AP (see the version should also give this), it indicates a regulatory domain (for example - A,-E, n, z). This means that your vWLC set up with a country code in this regulatory area. The document below for more details http://www.cisco.com/c/en/us/products/collateral/wireless/access-points/product_data_sheet0900aecd80537b6a.html * don't forget to rate our answers if you find them useful * HTH Rasika

• Dynamic management of the mobile AP management interface to another dynamic interface (WLC 2504)

  Situation/configuration is the following:

  -2504 WLC (8.1.131) with a total of 22 AP is connected.

  -Several WLAN active each with its own interface (dynamic)

  -L' (static) management interface is the option "Activate the dynamic management of AP" enabled.

  -The four physical interfaces of the WLC remain TROLLING configured.

  What is the problem:

  In the current configuration, the management interface is in the same vlan as the AP we now want to move the management interface to a different VLAN, but keep the AP in the vlan current. The idea is to move the management interface to its new vlan and disable "enable dynamic management of AP". Then, create a new interface (dynamic) in the same vlan as of AP and select 'turn on the dynamic management of AP' on this interface. Configure it as it is no problem but is does not work. The AP will record is no longer with the WLC.

  Is there something I may be missing why this does not work?

  Richard.

  Yes, that's the gist of it.

  I recommend always making a capture packets if only just for educational purposes and to see how this works in action. I found it interesting when I did in the lab here.

• WLC 5508 management interface

  Hi, I have a design requiring a WLC 5508 be connected to two separate swithces specific wireless. WLC 1 port is connected to the switch A trunk and WLC Port 2 is connected to the switch B. Each switch has its own local VLANS. When I connect the years 1130 towers they need find the interface of management initially then only use management. AP interfaces since there is only a single management interface, if the assignment of management interface on a VLAN that is configured on the switch then APs on spend a fine join but those switch B continue to ask for the management interface and the version debug capwap on WLC he says that this query Join were received on the bad ineterface...

  the only work around that was to do the routing between switch A and switch B for both VLAN residing APs... but for security reasons - customer would like to avoid this

  any help is appreciated...

  Unfortunately, the initial discovery must arrive in the management interface.  Once this has happened the AP expected the second AP manager who is on the subnet of comments, therefore, they are able to stand.  But if the AP is restarted, it would need to discover once again and would fail.

  What is the concern of customers to have all routable network mgmt AP?  guest users can not see anything there.

  IMO, let the AP able to connect to the subnet of mgmt, but then put an ACL L3 upward, to block the subnet of comments to achieve anything in the internal network.

• 4240 IPS management interface MAC address

  Hi all

  I use DHCP in my network. And I need to book a single IP address for the Interface of management of the IPS.

  I tried to get the MAC but could not. It is not yet on the Show of support.

  Can a please tell me how to get the MAC address IP management interface?

  If the interface to see the output does not give you this information, you can connect via the service account and run the command "ifconfig - a". Just make sure you do a 'su' - otherwise this command is not available.

  Please note if useful :)

  Concerning

  Farrukh