memory and bios

Similar Questions

• Sat Pro 2470 memory and BIOS update

  I recently received from Win XP SP 2 installed on the laptop and the free memory is very low (64 internal, additional 64 installed)

  I would like to add 2 x 128 MB to 320 MB total authorized under the current BIOS.

  After doing this, the manual says in Chapter 8 on page 7 that some files must be removed by following these steps:

  Click Start, and then turns off
  Brand to start the computer in MS-DOS klik OK

  Write to CD\Windows - renterb]
  Write the output - enter

  With XP, I can't find the option to choose start in DOS at the next startup. Is this also necessary when I add memory?

  Question: why should the battery be taken out when changing the memory? Isn't out enough power?

  WE BIOS: I can't find any information on what brings the BIOSupgrade available for this laptop. If I update the BIOS, which is the maximum size RAM and HARD drive? All the other important points?

  Concerning

  Jonas L/Brussels

  Hello

  I don't think that you should remove all files with Windows XP.
  Simply insert the modules of memory and power on the machine.
  Updated the BIOS normally does not increase the available memory.

  Good bye

• Memory and disk HARD upgrade question - Satellite 5200 801

  Hi all

  I really need your help to upgrade my toshiba Satellite 5200 801 (model: PS520E-31P1D-EN), basically it's the version specification factory (technical instructions on the link below)
  http://www.cwrose.de/Toshiba/S5200.html

  What I want is to get faster internal memory, you can buy for this model (currently I have two default 256 mb DDR 266 MHz CL2.5 memory sticks). Will probably do a gig of memory (I could have more, but it depends on the price).
  As well, I want to spend the HD to 160 gig (about), as well as get a faster hard drive then the current 60gig 4200 RPM Hitachi HD (as soon as possible for the specifications of my laptop).

  Anyone know what would be the best option?

  Someone said that it would cost all under 100 (that would be cool), but I don't know anything about the compatibility of different companies etc.
  Can anyone recommend what equipment... .and where * I hope that ebay or studs :)
  I need to go to get this sorted out

  PS:
  FYI, I mostly use the laptop for graphic design, video, and the interwebz.

  Thanks for any help you can give!
  Andy123n

  Hello

  You can upgrade the Satellite 5200 801 memory and HARD drive.
  S for laptop computer memory can be improved up to 1 GB of RAM. So you can use 2 x 512 MB PC2100 DDR - RAM modules.

  Check this link 5200-801 Satellite:
  http://www.orcalogic.co.UK/ASP/ProdType.asp?ProdType=6116&ft=m&St=3

  In my opinion, you can use the modules of memory from different manufacturers, but the module must support these specifications: 200-Pin PC2100 (266 MHz) DDR SODIMM
  I suppose you could also use a 400 Mhz because the laptop supports a 400 Mhz FSB too.

  I think that an upgrade of the IDE 160 GB HARD disk is not possible. To my knowledge, the BIOS can support such massive size of the HARD drive. But this is only my personal opinion. If I was you I would try a smaller HDD like 100 GB or 120 GB.

  Concerning

• Can I upgrade the memory and the graphics card on Satellite A60

  Hi all..
  I have a satellite a60 652.
  I want to improve it with new ram and graficcard.
  can I use more than 1, 5 GB of ram? later with an update of the bios?
  and if I can change the graficcard? If the answer is Yes... What is the best card I can actually use?
  or is there a map which is almost a geforce 7600 or 6600 (or ati 9700) I can use?

  Thank you for the help
  Ingo

  PS excuse my English ;)

  > I want to upgrade the ram and the new graphics card

  Upgrading RAM is possible but the graphics card is unable to be updated!

  If you want to upgrade the memory you could update to 1536 MB max.
  The A60 supports 512MB internal memory and it is so that one memory slot where the extra RAM module can be inserted.

  These modules are compatible:
  PC2700 512 MB (PA3312U - 1 M 51)
  1024MO PC2700 (PA3313U-1M1G)

  Concerning

• SR2180NX adding memory and a video card, how?

  I finally decided to do a upgrade to my PC but I pushed my brain batty, trying to figure out how I would add memory and if I should update my video card now cause my Sims 2 game, instead of smooth running, it runs a little rough and frame by frame. Very annoying. I also want the Sims 3 to be able to run on my computer, I hope I can get it all done before they release.
  I have windows vista Home premium, and I have a PC I did not do anything for her, so it's a bit as if it was from the factory around a few programs of vanilla.
  
  * Manufacturer * Compaq Presario
  * Product * RK548AA-ABA SR2180NX
  Total number of logical CPUS * 2
  Total physical memory * 1.00 GB
  Total number of optical drives * 1
  Total number of disks hard * 1
  Total number of video cards * 1

  * Memory *.
  ------------------------------------------------------------------------------
  * System memory * total physical memory * 1.00 GB
  * Free physical memory * 443,21 MB
  Total virtual memory * 2.00 GB
  * Free up virtual memory * 1.94 GB
  * Page file space * 2.24 GB
  
  * 512 MB DDR2 - SDRAM (PC2-4200 / PC2-4300 / 533 MHz) * memory size * 512,00 MB
  * Type of memory * DDR2 SDRAM (PC2-4200 / PC2-4300 / 533 MHz)
  * Manufacturer of memory * Hyundai Electronics
  * Date of manufacture memory * week 39, year 2006
  * Revision memory code * 4141
  
  * 512 MB DDR2 - SDRAM (PC2-4200 / PC2-4300 / 533 MHz) * memory size * 512,00 MB
  * Type of memory * DDR2 SDRAM (PC2-4200 / PC2-4300 / 533 MHz)
  * Manufacturer of memory * Hyundai Electronics
  * Date of manufacture memory * week 39, year 2006
  * Revision memory code * 4141
  
  * Video card *.
  ------------------------------------------------------------------------------
  * Intel (R) 82945G Express Chipset Family * manufacturer * Intel Corporation
  * Video card chip Type * Intel (R) 82945G Express Chipset Family
  * Video card memory * 256,00 MB
  * Video card BIOS * Intel video BIOS
  *Driver*c:\windows\system32\drivers\igdkmd32.sys
  * Version * 7.14.10.1461, 25/03/2008
  ------------------------------------------------------------------------------
  and it's the plug to run the Sims 3
  ------------------------------------------------------------------------------
  THE SIMS 3 MINIMUM REQUIRED HARDWARE CONFIGURATION
  
  FOR WINDOWS VISTA
  * Windows Vista (Service Pack 1)
  * 2.4 GHz P4 or equivalent
  * 1.5 GB OF RAM
  * At least 6.5 GB of disk space hard at least 1 GB additional space happy Custom
  * 128 MB video card with support for Pixel Shader 2.0
  
  For computers using built-in graphics chipsets, the game requires at least:
  * Intel Integrated Chipset, GMA X 3000 or more.
  * 2.6 GHz Pentium D CPU, or 1.8 GHz Core 2 Duo or equivalent
  * 0.5 GB additional RAM
  
  SUPPORTED VIDEO CARDS
  NVIDIA GeForce series
  FX 5900, FX 5950
  6200, 6500, 6600, 6800,
  7200, 7300, 7600, 7800, 7900, 7950
  8400, 8500, 8600, 8800
  9600, 9800, GTX 260, GTX 280
  
  Series ATI Radeon™
  9500, 9600, 9800
  X 300, X 600, X 700, X 800, X 850
  X 1300, X 1600, X 1800, X 1900, X 1950
  2400, 2600, 2900
  3450, 3650, 3850, 3870,
  4850, 4870
  
  Intel® Extreme Graphics
  GMA X 3 x 00 series
  Laptop versions of these chipsets may work, but can run relatively slower. Autonomous cards installed in vanilla (not PCIe or PCIx or AGP) PCI slots, such as some GeForce FX variants, will perform badly. Intel chipsets integrated starring parts underclockes would not run properly.
  
  Chipsets integrated such as the ATI Xpress and the NVIDIA TurboCache variants will have low settings selected, but should operate satisfactorily.
  
  Please note that attempting to play the game using video hardware that is not listed above may result in reduced performance, graphical issues or make the game work do not at all.
  The NVIDIA GeForce FX series is unsupported under Vista.
  
  and he also said when I watched the news of the memory of the BIOS screen:
  
  Installed memory 1024 MB/PC2-4200
  Bank 1 512 MB/DDR2 SDRAM memory
  Memory Bank 2 not installed
  Memory bench 3 512 MB/DDR2 SDRAM
  Memory bench 4 not installed

  I know that I have to add memory and a video card, or even a power supply according to the video card, I get. Memory seems simple and easy to do, but the power SUPPLY and the video card, makes me a little nervous, any suggestions on what I should get and instructions on how to proceed will be greatly appreciated Thx! I apologize for this post being so long.

  Message edited by CareBear31 on 02/05/2009 13:02

  Adding instructions are here. When you buy new memory be sure and go to the website of the manufacturer of the memory. Use only brands so that they ensure th your product compatibility. Use the memory Configurator tools on the website of the manufacturer of the memory. Here are a few major brands for you: Kingston, Crucial, Corsair:

  Change the power supply: This video on youtube is pretty decent for generic power supply switching.

  Thislinkhas information on opening the cover and remove the cover.

  When you select a video card do not get cards great physically (i.e. ATI HD 4870 / 4850) because they are double wide and does not have limited space. Fantastic cards but are not for the pre-built PC.

  Any ATX PSU fits your case. 450 watts or therabouts enough for almost any addition of hardware on your pc. Do yourself a favor and stick the best brands such as Corsair, OCZ and others. Generic brands are not worth the problems they can bring even if they are cheaper.

• HP 550: updated hp 550 memory and cpu with the unconventional settings. is not ideal, but not other choice

  HI guys, I hope you can help or at least give a point in the right direction. I am a freelance photographer with a large part of the suite creative Adobe CS6. After a disaster of a week, I came home to find the motherboard on my editing station is fried somehow. I don't know what happened though I wouldn't put past my inattention of roommates.
  I'm desperate. I have to finish my current job until I'm able to afford to buy a replacement. So I have to rely on stop-gap measures, in desperation to finish my project, that are less than ideal, but so far are doing better than I'd hoped.
  Im a photographer, Capture One, Adobe Photoshop Lightroom, Adobe Photoshop and Premiere Pro are the go for workaholic applications that I need to work. without them I have no income. in order to have this machine run these applications,
  the machine I have left is an old hp 550 that was gathering dust in the closet. It was built for 32 bit Win XP and in no case is designed to run adobe products food pork I use, particularly of Lightroom.
  Unfortunately PS with Lightroom and first are 64-bit programs and LR and first are hyper threaded. so I did some research and with the help of the list of the utility windows 7 Advisor to upgrade instructions, I was able to get windows 7 Pro 64-bit to install and run.

  I know that this is not the ideal machine or the situation, but for a few weeks, I need to make it work.

  I really just 2 simple questions. First of all, I went to the HP technical support. but they were not useful. as the guarantee of the laptop are long gone, they would be not even polite and basically told me to shove off. Then on another forum, I called back and comes with a knowledge it all who constantly insisted on the fact that there was no way no how this pc could run 64 bit win 7, which i thought what am I seeing things? It works very well for 3 months. So I decided to come to you. your forums were useful on many occasions.

  Basically, I need this machine to run these programs during the next month or two, until I can buy a new machine.

  essentially, what I want to know, it's the motherboard support an upgrade of the processor? and if anything goes, what do you suggest as a substitute, given my needs? The Core 2 duo is the bare minimum of what I can limp with like photo/video rendering times are excessively slow.

  then I was talking to the support staff essential tech upgraded memory. and possibly set the bios to force to run 8 gigs of ram. They said that they have cold cannot find any version of bios that would make that possible, but only by forcing already run 64 bit, which has already allowed the pc to use the full 4 GB of ram, which was impossible in the 32-bit format. He suggested that I buy 2 4 gig modules such as 4 GB DDR2 PC2-5300 unbuffered NON - ECC, 1.8V 512Meg x 64 which can be seen at http://www.crucial.com/usa/en/memory/ct51264ac667 and try to install the full 8 concerts and see what would happen, saying that he had a feeling that I might get lucky. his logic is that the 64-bit system already open the ram limits and who knows, you can't make an omelet without cracking of eggshells! It seemed very optimistic. So, what do you think? It seems likely you because I love to work. or do you think the guy was a quack? and this whole endeaver is a waste of time and money?

  also, any other suggestions on how to time this month long storm that do not involve suggestions of buying new machines would be appreciated!

  so that you have accurate details below are my system specs.

  Hewlett-Packard HP 550 F05
  System serial number: CNU90716GN
  Inventory number: CNU90716GN
  Chassis serial number: CNU90716GN
  Case type: portable

  Windows 7 Professional (x 64) Service Pack 1 (build 7601)
  Install language: English (United States)
  Local system: English (United States)
  Installed: 04/08/2014-18:21:11
  Start mode: BIOS (Secure Boot not supported)

  Processor and b main circuit
  1.80 GHz Intel Core2 Duo processor
  cache of 64 kilobytes main memory
  secondary memory 2048 k-cached
  64-bit ready
  Multi-core (2 total)
  Not hyper-threaded Board: Hewlett - Packard 3618 KBC Version xx.xx
  The bus clock: 200 MHz
  BIOS: Hewlett-Packard 68MVU worm. F05 19/01/2009

  Readers of memory Modules c and d
  2320.47 GB drive hard usable capacity
  959.16 gigabytes of free disk space

  HL-DT-ST DVDRAM GSA - T50L ATA Device [scanner]

  Hitachi HTS543216L9A300 [hard drive] (160,04 GB) - drive 0, s/n 090108FB0200VCCPYM3B, rev FB2OC40F, SMART location: healthy
  ST1000LM 024 HN-M101MBB USB Device [hard drive] (1000,20 GB) - drive 3
  ST310005 USB Device [hard drive] 28as - 1 player
  WD 1600JS external USB Device [hard drive] (160,04 GB) - disc 2, s/n WD - WCANM2342148 4088 usable MB installed memory

  Slot ' DIMM #1' has 2048 MB (serial number 0000202 A).
  Slot ' DIMM #2' has 2048 MB (serial number 00004042).

  Thank you friends! I can't wait to read your tips!

  Jodie

  Here is the Manual:

  Repair manuals

  Unfortunately, the maximum configuration is a processor T5670 1.8 ghz and 4 GB of DDR2-667 memory, you already have. The CPU includes the 64-bit instructions is not surprising, that it can run Windows 7 64-bit. My best advice is to save your money for when you can get a real working machine. The only other likely to help is a solid state drive, you might use in the laptop and then also use the new computer that you intend to buy.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Upgrade Alienware 17 r2, graphics, memory and SSD; heating system and stops

  I tried to find information on the upgrade from my old system of r2 to Alienware 17 with new graphics, memory and an SSD, but I've been to find contradictory information on it, and if I would still be able to upgrade my graphics.

  My current setup is:

  Computer model M17x

  OS version Microsoft Windows 7 Home Premium

  Processor

  Manufacturer Intel Core i7 CPU M 620 @ 2.67GHz

  Clock speed 2.7 Ghz

  L2 Cache size 256

  Memory

  Available memory 35.50%

  The file size of the page 10 048,7 MB

  Available Page file 85.84%

  Virtual memory 10 048,7 MB

  Available virtual memory 63,04%

  M1 2 048,0 MB

  M2 2 048,0 MB

  Network card
  Storage
  Material

  Type Description

  CD-ROM/DVD-ROM readers Optiarc DVD +-RW AD - 7640S

  Disc players ST9250410AS

  Graphics cards AMD Mobility Radeon HD 5800 series

  IDE ATA/ATAPI controllers Intel (r) 5 Series 6 Port SATA AHCI Controller

  Keyboards, mice & pointing devices Synaptics PS/2 Port TouchPad Compatible mouse HID Microsoft Hardware USB mouse Compatible mouse HID

  Monitors Generic PnP monitor

  Sound Devices IDT High Definition Audio CODEC AMD High Definition Audio Device

  USB controllers Intel (r) 5 Series/3400 Series Chipset Family USB Enhanced Host Controller - B 3, 34 Intel (r) 5 Series/3400 Series Chipset Family USB Enhanced Host Controller - 3B3C

  First of all, the graphics card can be improved and if so, should I go with?

  Depending on the type of memory I thought to install is:

  Crucial Ballistix Sport 16 GB DDR3 - 1600 PC3-12800)

  I heard that 8 GB was supposed to be the max, but that was only because it was all that was available at the time, the system was released and that others have used up to 16 GB.

  It will work or is there another suggestion?

  Thirdly, the SSD I plan on installing is:

  Crucial BX200 480 GB SATA III 6 Gb/s 2.5 "Solid State Drive CT480BX200SSD

  Still, I read the system never was not originally designed to support SATA III but if you use BIOS version A09 it would work.

  Is that correct or suggestions?

  The last two things I was wondering was that the system overheat easily and stops, to rebuild the thermal paste on the CPU and heatsink help correct this?  As well as to clean the fans, of course.  Or are there other options I should look into?

  Anyone know where to buy a new adapter power for this system as well?

  Thank you in advance for any help you can provide me with.

  Hello.

  First of all I would like to ditch the 620M processor, it's i7 below, you can get and dual-core only, not quad.

  You should be able to find an i7 820QM at a reasonable price, these days, 920QM or 940QM would be even better, they were the fastest available for this model.

  Once you have upgraded the CPU to something on an i7 720QM you can upgrade you RAM to 32 GB at 1333 MHz with no problems, if you want faster than 1333 you need to adjust overclock settings in the system BIOS.

  You have two HDD slots, up to any size SSD 1 TB plug-and-play (or to the more require very few adjustments BIOS) Firmware may need to be updated but also that it should be OK, just stick with an alienware used as Samsung brand, and if you can get one from the SSD slightly more older you might save money , you don't need a model 'latest and greatest '.

  Upgrade your GPU in the M17xR2 model can be a pain, the fan control is terrible and to really improve and play safely, you should probably use HW Monitor, so you do not cook your cards.

  Memory the AMD maps are more lenient when it comes to bi - GPU - I think remember me some upgraded GPU not X shot or SLIing in this model, but now is earlier in order not to forget.

  The M17xR2 is a very popular model, with thousands of people, the GPU upgrade - you can having to sort through the garbage to find the jewels but the info you need should be available if you do a search on google

  NotebookReview Forum would be a great place to start, 99% of the info you need should be there, the other 1% proably will be on techinferno.

  Guilbert - I still think that the M17xR2 has been one of the best they have done...

• IRLQ_LESS_OR_NOT_EQUAL_TO 0x000000A then proceeds to run a physical memory dump, I also get something related to memory and then STOP 0x0000001A and 0x00000DE

  Usually when playing games, DOTA 2 and Battlefield 3, I get them more when im playing battlefield 3.

  Hello

  Don't forget to check with the support of game manufacturers and ask in their forums to see if there is
  known problems.

  ---------------------------------------------------------------------------------------

  Results verified BlueScreenView WinDBG / DumpCHK.
  
  The Bug_Check have been in 0a, 1A, 7, 50 and.

  When there is that much material different from Bug_Check is almost always involved
  at least some of the issues.
  
  1. remove ALL power and then reinstall memory cards and cables (at both ends, where possible).
  in fact, remove and replace - don't do not just tight. Clean the dust bunnies and ensure that fans
  work. Try adding a small fan blowing into the socket to reduce the effects of heat (heat
  related not always means excessive heat that something might be too sensitive to the same
  normal levels).

  2. test the memory carefully using methods in the troubleshooters below. Keep in mind
  This memory tests only detect all errors as the moment where there are tiny speed differences
  between the modules that appear to be identical. It is necessary to test the modules in
  various combinations and models.

  3 several of the Bug_Check showed CAUSE nvlddmkm.sys who, in the Nvidia video driver.
  Search for Nvidia updates. See the driver update methods in the resolution of the problems previously posted
  above.

  NVIDIA - drivers - use OPTION 1 to manually enter your info driver to get the most recent drivers.
  http://www.nvidia.com/download/index.aspx?lang=en-us

  NVIDIA Support - check with the support that she might be a known issue
  http://www.nvidia.com/page/support.html

  NVIDIA forums - also check for the forums it might be a known issue or others likely to have
  http://forums.nvidia.com/

  4 check system Maker (manufacturer of motherboard for customized systems) updates to the BIOS,
  chipset drivers low level and major of edge and separate device drivers. Use DriverView
  -Microsoft drivers hide the value VIEW - updated those without emptying in their names. (See pilot
  methods of update in convenience stores previously posted.)

  5. after updating the drivers run DriverVerifier as shown in the troubleshooter below.

  6 use other methods of troubleshooting in convenience stores posted previously and those
  below as needed.

  ===========================================================

  BCCode: 0a 0x0000000A methods as well as updates to driver and memory tests
  are in the resolution of the problems previously shown.

  ===========================================================
  
  BCCode: 1a 0x0000001a

  Remove ALL power and reinstall all the memory cards and cables (both ends where possible).
  in fact, remove and replace - don't do not just tight. Make sure that the vents are clear and that the
  the fans are working. Even if the temperature is OK assume no heat does not affect the video,.
  sound or other system functions that it these get hot. Try adding a small fan blowing in
  the vents as a test. (These are especially for a PC not a laptop.)

  Have you recently added any hardware? Have you updated any drivers just before this started?
  (Check control panel - updates of Windows to see if all drivers have been updated it on the)
  This started the time) likely guilty hand are video driver, other great drivers, memory, and
  antivirus/antispyware/security products could be at fault as well as reader questions.

  Use the troubleshooter below and refer to the following message to drivers and memory when
  you get these sections and then back to the resolution of the problems according to the needs.

  BCCode: 1a 0x0000001a<-- read="" this="">
  http://www.faultwire.com/solutions-fatal_error/memory-management-0x0000001A-* 1041.html? order = votes

  ===============================================================

  BCCode: 7F 0x00000007E who is also a 0x1000007E

  See these KB articles:

  "Stop 0x0000007E" or "Stop 0 x 00000050" error message in Windows 7 or Windows Server
  2008 R2
  http://support.Microsoft.com/kb/979538

  "Stop 0x0000007E SYSTEM_THREAD_EXCEPTION_NOT_HANDLED" error when the GPU is under
  conditions of heavy load in Windows 7 or Windows Server 2008 R2
  http://support.Microsoft.com/kb/983615

  References to Vista also apply to Windows 7.

  BCCode: 7F 0x0000007E which is also 0x1000007E

  This error is usually a driver problem and display adapter (video) driver is the most suspicious if she
  may be others. Antivirus/antispyware/security programs, equipment (heat) and major software problems
  can also cause the error. When you get to the section of the driver to use the Troubleshoot utility my generic
  methods in the next message and then return to the if necessary troubleshooting tool.

  Have you recently added hardware or drivers updated? Don't forget to look in Control Panel - Windows
  Updates to see if all drivers have been updated it. Other donor opportunities include the antivirus/anti-
  spyware/security programs.

  When you get to the pilot and sections of the memory of the troubleshooter check the following message to
  update drivers and memory test and then return to the troubleshooter if necessary.

  BCCode: 7F 0x0000007E which is also 0x1000007E

  Cause

  SYSTEM_THREAD_EXCEPTION_NOT_HANDLED bug control is a very common bug control. TO
  interpret, you must identify which exception has been generated.

  Common exception codes are:

  • 0 x 80000002: STATUS_DATATYPE_MISALIGNMENT indicates an unaligned data reference was encountered.

  • 0 x 80000003: STATUS_BREAKPOINT indicates a breakpoint or ASSERTION was met when no kernel debugger was attached to the system.

  • 0xc0000005: STATUS_ACCESS_VIOLATION indicates a memory access violation has occurred.

  For a complete list of exception codes, see the Ntstatus.h file located in theinc directory
  the Microsoft Windows Driver Kit (WDK).

  Solve the problem

  If you do not have to debug this problem, you must use certain basic troubleshooting techniques.

  • Make sure you have enough disk space.
  • If a driver is identified in the bug check message, disable the driver or check with the
  • Reference of the manufacturer for driver updates.
  • Try changing video cards.
  • Check with your hardware vendor for updates to the BIOS.
  • Disable the BIOS memory options such as implementing caching or shading.

  If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2
  (the address of the exception) must identify the driver or function that caused the problem.

  If the exception code 0 x 80000003 occurs, a hard-coded breakpoint or assertion was hit, but the system
  has been launched with the /nodebug. switch. This problem should occur infrequently. If it occurs repeatedly,
  Make sure that a kernel debugger is connected and the system is booted with the Switch/DEBUG .

  In case of exception code 0 x 80000002, the trap frame provides additional information.

  If you do not know the specific cause of the exception, consider the following questions:

  • Hardware incompatibility. Make sure all new hardware that is installed is listed in the
  • List of Microsoft Windows Marketplace tested products.
  • Service driver or defective peripheral system. A service driver or defective peripheral system can be
  • responsible for this error. Hardware problems, such as the incompatibilities of the BIOS, memory, conflicts
  • and IRQ conflicts can also generate this error.

  If a driver is listed by name in the bug check message, disable or remove that driver. Disable
  or remove drivers or services that have been recently added. If the error occurs during startup
  sequence and the system partition is formatted with the NTFS file system, you may be able to use safe
  Mode to rename or to delete the faulty driver. If the driver is used as part of the system startup procedure
  in Safe Mode, you must start the computer by using the Recovery Console to access the file.

  If the problem is associated with Win32k.sys, the source of the error may be a third remote
  control program. If this software is installed, you can remove the boot of the computer service
  by using the Recovery Console, and then by removing the offending system service file.

  Check the system log in Event Viewer for additional error messages that might help identify the
  device or the driver that generated the bug check 0x7E.

  You can also disable memory cache BIOS may try to resolve the error. You should also
  Run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system.
  For more information about these procedures, see the manual of your computer.

  The error that generates this message may occur after the first reboot during Windows Setup, or
  Once the installation is complete. A possible cause of the error is lack of disk space for installation and system
  BIOS incompatibilities. For problems during the installation of Windows that are associated with the absence of disc
  space, reduce the number of files on the disk drive hard target. Find and delete any temporary
  the files that you do not have to have files hidden Internet, backup application and.chkfiles files that
  contain fragments of file saved to disk scans. You can also use another hard drive with more drive
  free space for the installation. You can solve the problems of BIOS by upgrading the version of the system BIOS.

  BCCode: 7F 0x00000007E who is also a 0x1000007E<-- read="" this="">
  * 1141.html? order = votes http://www.faultwire.com/solutions-fatal_error/System-thread-exception-not-HANDLED-0x0000007E-

  ===============================================================

  BCCode: 50 0 x 00000050

  References to Vista also apply to Windows 7.

  Have you recently added any hardware? Have you updated any drivers just before this started? (Check
  Panel configuration-updates of Windows to see if all drivers have been updated it there all the time it started)
  Main likely culprits are video driver, other great drivers, memory and antivirus/antispyware/security
  products could be at fault as well as reader questions.

  Use the troubleshooter below and refer to the following message to drivers and memory when you get to
  These sections and then back to the resolution of the problems according to the needs.

  BCCode: 50 0 x 00000050

  Cause

  The BCCode 50 usually occurs after the installation of faulty hardware, or in case of failure
  hardware installed (usually associated with a faulty RAM, be it the main memory, L2 RAM cache memory, or)
  Video RAM).

  Another common cause is a defective system service installation.

  Antivirus software can also trigger this error, as can a corrupted NTFS volume.

  Solve the problem

  Solve a defective hardware problem: If the material has been added to the system recently,
  Remove to see if the error recurs. If existing hardware has failed, remove or replace
  the defective component. You must run the diagnostics of material provided by the manufacturer of the system.
  For more information about these procedures, see the manual of your computer.

  Fix a defective system service: Disable the service and confirm that this
  resolves the error. If so, contact the manufacturer of the service on a possible system
  Update. If the error occurs during the system startup, restart your computer, and press F8 to
  character mode menu that displays the choice of operating system. As a result
  Windows Advanced Options, select last good known Configuration option menu.
  This option is most effective when a pilot or a service is added at a time.

  Solve a problem of antivirus software: Disable the program and confirm that this fixes
  the error. If this is the case, contact the manufacturer of the program about a possible update.

  Fix a corrupted NTFS volume:  Run Chkdsk /f /r to detect and repair disk
  errors. You must reboot the system before the start of the analysis of disk on a system partition. If
  the hard drive is SCSI, check for problems between the SCSI controller and the disk.

  Finally, check the system log in Event Viewer for additional error messages that might help
  identify the device or driver that generated the error. Disable the cache in memory of the BIOS
  could also resolve it.
  
  BCCode: 50 0 x 00000050<-- read="" this="">
  * 1095.html? order = votes http://www.faultwire.com/solutions-fatal_error/page-fault-in-NONPAGED-Area-0x00000050-

  ===============================================================

  BCCode: OF 0x000000DE

  This is usually a driver issue then run DriverVerifier and check the drivers using the methods
  in troubleshooting below. Carefully check the memory using the methods below.

  BCCode: OF 0x000000DE

  Bug Check 0xDE: POOL_CORRUPTION_IN_FILE_AREA

  Bug POOL_CORRUPTION_IN_FILE_AREA control has a value of 0x000000DE. This indicates that a driver has corrupted the memory pool that is used to maintain pages to disk.

  Important information if you have received a STOP Code

  If you have received a blue screen error, or stop code, the computer stopped abruptly to protect against data loss. A hardware device, its driver or software might have caused this error. If your copy of Windows is shipped with your computer, contact your computer manufacturer. If you purchased Windows separately from your computer, Microsoft provides support. To find contact information for Microsoft or the manufacturer of your computer, Contact Support.

  If you have experience with computers and try to recover from this error, follow the steps in the Microsoft article solution STOP (blue screen) errors in Windows.

  The following actions could prevent a mistake like this does not happen:

  1. Download and install updates for your computer from Windows Update device drivers.
  2. Scan your computer for computer viruses.
  3. Check your hard drive for errors.

  POOL_CORRUPTION_IN_FILE_AREA settings

  None

  Cause

  When the memory dereferenced Manager the file, he discovered this type of corruption of memory pool.

  BCCode: OF 0x000000DE<-- read="" this="">
  * 1221.html http://www.faultwire.com/solutions-fatal_error/A-Driver-corrupted-pool-Memory-used-for-Holding-pages-0x000000DE-

  ===================================================

  Driver Verifier can help find some BSOD problems:

  Using Driver Verifier to identify issues with Windows drivers for users advanced
  http://support.Microsoft.com/kb/244617

  How to solve the problems of driver in Windows Vista or 7.
  http://www.WinVistaClub.com/T79.html

  Using Driver Verifier
  http://msdn.Microsoft.com/en-us/library/ff554113 (v = VS. 85) .aspx

  How to use Windows drivers check Manager to solve problems and identify the Driver questions
  http://www.YouTube.com/watch?v=_VwIDD9xngM

  Driver Verifier
  http://www.techsupportforum.com/2110308-POST3.html

  Using Driver Verifier
  http://www.faultwire.com/solutions/using_driver_verifier.php

  How to use Windows drivers check Manager to solve problems and identify the Driver questions
  http://www.YouTube.com/watch?v=_VwIDD9xngM

  You can disable the driver verifier
  http://support.Microsoft.com/kb/244617

  Start - type in the box search-> auditor/Reset hit enter to disable

  BlueScreenView lets you know if there is a driver specified in the error message. Also check with
  MyEventViewer at the blue screen.

  If DriverVerifier creates a minidump upload it and post the link here so we can analyze.

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Today, we are locked into sitting and staring at the stupid hourglass or spinning cirlces infinite so that your OS continues to steal the memory and performance

  I just want you know I hate using this operating system. WIN 7 and WIN 8 on different computers. Years ago the opportunity to correct a bit your * but today we are locked in to sit and watch the fool or spinning cirlces infinite hourglass while your OS continues to steal the memory and performance of any type of material that is using your operating system. I can't wait to own a computer that runs an operating system that doesn't degrade not just because I use it for work and play. There is a special place in * for windows programmers and engineers.

  Original title: why windows suck so bad!

  Hello

  These should help:

  Ways to improve the performance of your PC
  http://Windows.Microsoft.com/en-us/Windows-8/improve-PC-performance

  Maintenance & performance
  http://Windows.Microsoft.com/en-us/Windows/performance-maintenance-help#performance-maintenance-help=Windows-8&V2H=win7tab1&V3H=winvistatab1

  Crashes Windows or freezes
  http://support.Microsoft.com/kb/2681286

  How to speed up your PC
  http://support.Microsoft.com/kb/2746761/en-us

  =======================================================

  You use a 3rd party antivirus/antispyware/security program? If so many people
  can cause slow start from the bottom.

  Check with the support of the system Maker (manufacturer of motherboard for customized systems), their
  online resources and the drivers and ask questions in the forums about known problems.
  Updating the BIOS , drivers of low level chipset and embedded and separate major
  device drivers (anyone who can have an impact on the speed of startup and performance).

  Note the use of Win Key + X and Win Key + W (to go on the Control Panel, Run and parameters
  According to needs). Win + D key calls the office and using Win Key active / disable the office and
  Splash screen.

  Check startup programs.

  Right-click in the left lower corner - Manager of tasks
  Or Windows key + X - Manager of tasks
  Or right click on the taskbar - task manager

  Check the Startup tab.

  More troubleshooting:

  How to perform a clean boot for a problem in Windows Vista, Windows 7,
  or Windows 8
  http://support.Microsoft.com/kb/929135

  Other programs to help:

  Autoruns - free - see what programs are configured to start automatically
  When your system boots and you connect. Autoruns also shows you the complete list
  Registry and file locations where applications can configure auto-démarrer parameters.
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Process Explorer - free - find out what files, registry keys, and other objects
  processes have open, which DLLs they have loaded and more. This unique
  powerful utility will show you even owned by each process.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653.aspx

  =======================================================

  If necessary:

  Try to do a "Refresh your PC without affecting your files" (or modification of your personal data
  settings) or even a restore. Be prepared to re - install the programs, applications will remain.
  And having redundant backups of your files on the disk main hard is always a
  good idea.

  Windows 8 includes special discount methods (keep files and settings) or a reset
  (new installation remove all).

  How to restore, refresh or reset your PC
  http://Windows.Microsoft.com/en-us/Windows-8/restore-refresh-reset-PC

  How to create a system image to refresh your PC in Windows 8
  http://support.Microsoft.com/kb/2748351

  How to update Windows 8
  http://www.eightforums.com/tutorials/2293-refresh-Windows-8-a.html

  How to reset Windows 8
  http://www.eightforums.com/tutorials/2302-reset-Windows-8-a.html

  If you need a repair disc:

  Create a system repair disc
  http://Windows.Microsoft.com/en-us/Windows7/create-a-system-repair-disc

  How to create a "system repair disc" (CD/DVD) in Windows 8
  http://www.eightforums.com/tutorials/2855-system-repair-disc-create-Windows-8-a.html

  How to create a recovery USB in Windows 8
  http://www.eightforums.com/tutorials/5132-recovery-drive-create-USB-flash-drive-Windows-8-a.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• My calendar retains the events for a month, but when I look back over the past months, only recurring and default events are preserved.  I have a bad memory and I want that all events held on my calendar.  How can I do this?

  My calendar keeps events a month, but when I think back several months, only recurring and default events are preserved.  I have a bad memory and want to keep all the events, I put on my calendar for a year.  How can I do this?

  Go to settings > Mail, content, timing and you should see an option for synchronization. Make sure that you put in all the events if you want to keep past events calendar

  Alternatively you can also use iCloud.com to restore calendar events that may have been accidentally deleted

  If you've accidentally deleted your calendars, reminders, or contacts of...

  I hope this helps!

• I have an iMac OSX 10.8.5 2008 30.6 GHz Intel Core 2 Duo Processor with 4 GB 800 MHz DDR2 SDRAM Memory and 1 t HD

  I have an iMac 24 "Early 2008 OSX 10.8.5... 30.6 GHz processor Intel Core 2 Duo with 4 GB 800 MHz DDR2 SDRAM memory and 1 t HD.  Can I upgrade the processor speed and if so what.  Can I upgrade the memory and if so what.  I launched iPhoto ' 08 7.14.  Any input would be great.  Thanks for your help and suggestions.

  You can actually move the ram to 6 GB.

• How to take movies on my macbook air to free up memory and still access those I downloaded from iTunes?

  I want to free up the memory on my macbook air and have 65 GB of movies hogging the space. I don't want to lose them forever if you want to know how I can free up memory and again back to the film at some point in the future.

  If they were purchased through iTunes, you can download again them at any time.

  However, there is no way to stream movies, so you have to download the entire file again for a movie.

  Open iTunes > iTunes Store > purchased (on the right side of the window) > movies.

  Make sure that the sort is set to "Not in my library" If you try to redownload something that has been removed from the computer.

• I want to upgrade to El capitan, but need to 8 GB memory and now have only 4.  How much would it cost to add 4 GB of memory?

  I want to upgrade to El capitan, but need to 8 GB memory and now have only 4.  How much would it cost to add 4 GB of memory?

  It depends on what Mac model you have and is not possible for all models. Go to the website of OWC or Crucial and check.

  (141711)

• Tecra M9 - reader of fingerprints and BIOS password

  Aloha
  I want to disable the fingerprint reader and bios password at startup of the computer.
  I already uninstalled upek protector suite ql 5.4.0.2934, but at the start, I'm still prompted to slide my finger.
  I've seen and followed the instructions in "toshiba passes: definition and suppression (BIOS passwords, supervisor and Windows)", but I still have to enter my password to start the computer.
  What should I do?
  Mahalo

  In the field "Enter new password" press only in order to remove the old drive HARD password... Repeat this in the field "confirmation"...
  Then he must change the password for HARD drive status to "unregistered".
  After that, save the BIOS changes and exit the BIOS.

• I have a macbook pro 15 "model 9.1 4 GB of memory and want to extend to 8 which is the model of memory should I buy for my fastest machine, I have for several years.

  I have a macbook pro 15 "model 9.1 4 GB of memory and want to extend to 8 which is the model of memory should I buy for my fastest machine, I have for several years.

  See:

  http://eShop.MacSales.com/shop/memory/Apple_MacBook_MacBook_Pro/upgrade/DDR3_160 0MHz_SDRAM

  Get only the memory of a place as above, since Macs are picky about the memory. Another place is crucial.

  If you can't swing for 16 GB (2 X 8 GB) replace a strip of 2 GB with a key of 8 GB.

  This is the Office Mac Pro forum. I asked that your post be moved to the MacBook Pro laptop forum.