Missmatch native VLAN on Metro Ethernet Service

Similar Questions

• access vlan vs $native Vlan

  SG300-28.  If I have config int IG20 to be switchport access mode and then vlan access on 100 but I and position the smartport office role, she set the vlan 1 If $native incoming unmarked headers are identified as being 100 or 1?  I tell myself that I need to change the params smartport or just leave it in auto smartport.

  interface gigabitethernet20

  activate the storm control

  Storm-control broadcast level 10

  Storm-control include multicast

  maximum port security by 10 points

  port security mode max-addresses

  port security throw trap 60

  spanning tree portfast

  switchport mode access

  switchport access vlan 100

  Office macro description

  switchport forbidden by default - vlan

  macro auto smartport type desktop $max_hosts 10 $native_vlan 1

        

  Hello Vini, out of the port was written by the macro for everything that you connected there. Your macro vlan native default is the vlan 1 so the port change as switchport mode access switchport access vlan 100 is essentially non-valid since your connection triggers a macro.

  If you need 100 unidentified port, you will need to disable the smart port or change the macro that is assigned the role of being vlan 100 native.

  -Tom
  Please mark replied messages useful

• 1252 config several VLAN trunking on ethernet not

  Hi all I am new to these forums, but have read some posts on configurations for an AP from 1252 to switch 2950.

  I have several VLANS andmultiple SSID configuration on my ap.  The switch knows the VLANS on the access point

  I think that in the config.

  When I put the 2950 in trunk mode on the port, the ap is conencted too, I can see no longer the access point. And none of my ssid / VLAN traffic through the stem net ether to the switch.  I think I have a problem with the config of the ap specifically either in the British Virgin Islands (do not understand this virtual port) or in bridge groups. (Never worked with foredeck groups.)

  The AP is in stand-alone mode.

  Here is my config on the side of the ap.

  interface Dot11Radio0

  no ip address

  no ip route cache

  !

  the cipher mode vlan 300 encryption tkip aes - ccm

  !

  broadcasting-key vlan 300 change 600 members-notice change in capacity

  !

  !

  SSID 101

  !

  SSID 300

  !

  countermeasure tkip duration of maintaining 120

  gain of antenna 0

  Base-1 speed, 0 2.0 5.5 11.0 6.0 12.0 9.0 18.0 24.0 36.0 48.0 54.0 m0. M1. M2. M3. M4. M5. M6. M7. M8. M9. M10. M11. M12. M13. M14. M15.

  root of station-role

  Bridge-Group 1

  Bridge-Group 1 block-unknown-source

  No source of bridge-Group 1-learning

  unicast bridge-Group 1-floods

  Bridge-Group 1 covering-disabled people

  !

  interface Dot11Radio0.100

  encapsulation dot1Q 100

  no ip route cache

  Bridge-group 100

  100 block-unknown-source bridge-group

  No source of bridge-group 100-learning

  No bridge group 100 unicast-flooding

  Bridge-group 100 covering people with reduced mobility

  !

  interface Dot11Radio0.300

  encapsulation dot1Q 300

  no ip route cache

  Bridge-group 255

  Bridge-group subscriber-loop-control 255

  Bridge-group 255 block-unknown-source

  No source of bridge-group 255-learning

  No bridge group 255 unicast-flooding

  Bridge-group 255 covering people with reduced mobility

  !

  interface Dot11Radio1

  no ip address

  no ip route cache

  !

  the cipher mode vlan 300 encryption tkip aes - ccm

  !

  broadcasting-key vlan 300 change 600 members-notice change in capacity

  !

  !

  SSID 101

  !

  SSID 300

  !

  countermeasure tkip duration of maintaining 120

  gain of antenna 0

  DFS block 3 Strip

  Speed - Basic6.0 9.0 12.0 18.0 36.0 24.0 48.0 54.0 m0. M1. M2. M3. M4. M5. M6. M7. M8. M9. M10. M11. M12. M13. M14. M15.

  channel SFR

  root of station-role

  !

  interface Dot11Radio1.100

  encapsulation dot1Q 100

  no ip route cache

  Bridge-group 100

  100 block-unknown-source bridge-group

  No source of bridge-group 100-learning

  No bridge group 100 unicast-flooding

  !

  interface Dot11Radio1.300

  encapsulation dot1Q 300

  no ip route cache

  Bridge-group 255

  Bridge-group subscriber-loop-control 255

  Bridge-group 255 block-unknown-source

  No source of bridge-group 255-learning

  No bridge group 255 unicast-flooding

  Bridge-group 255 covering people with reduced mobility

  !

  interface GigabitEthernet0

  no ip address

  no ip route cache

  automatic duplex

  automatic speed

  !

  interface GigabitEthernet0.51

  51 native encapsulation dot1Q

  no ip route cache

  Bridge-Group 1

  No source of bridge-Group 1-learning

  Bridge-Group 1 covering-disabled people

  !

  interface GigabitEthernet0.100

  encapsulation dot1Q 100

  no ip route cache

  Bridge-group 100

  No source of bridge-group 100-learning

  Bridge-group 100 covering people with reduced mobility

  !

  interface GigabitEthernet0.300

  encapsulation dot1Q 300

  no ip route cache

  Bridge-group 255

  No source of bridge-group 255-learning

  Bridge-group 255 covering people with reduced mobility

  !

  interface BVI1

  IP 10.131.10.70 255.255.255.0

  no ip route cache

  !

  51 of VLAN is what I'm trying to trunk more.  VLAN 100 is my networks vlan normal almost everything at the moment.  And my attempt to secure traffic wireless to a new vlan Vlan 300 more course on my local network.

  VLAN 51 has no ip address range

  IP VLAN 100 range is 10.131.10.0

  10.131.11.0 between 300 VLAN

  The routing goes to my switch 3750 core / router, but the access point is conencted to a 2950 namely shared resources to my layer distribution on a stack of 2975.  Once again the vlan 300 works on the 2975 stack and will pull dhcp if it is enabled.  Have not tried this on the 2950 yet, but I suspect it will also work based on the setting of the trunk on the s950 battery of 2975.

  In any case, I want to be able to do is have multiple VLANs configured on the AP (from most secure to least guarantee based on the capabilities of the equipment) and that traffic vlan tag go to my 3750 possibly for other guidelines.

  Here, any help would be greatly appreciated.

  Thank you for taking the time to read this.

  Sincerely,

  Kevin Pulford

  Systems administrator

  Harmon city, Inc.

  Yes, remove the vlan 51 can tell vlan 100 is the native, and there will be a link to bridge - Group 1.  Then change the switch port to vlan 100 native.  You should then be able to reach the access point via telnet/GUI.

  orders will be:

  config t

  No int dot11radio0.51

  No int dot11radio1.51

  No int g0.51

  int dot11radio0.100

  100 native encapsulation dot1q

  int dot11radio1.100

  100 native encapsulation dot1q

  int g0.100

  encapsulation dot1q 100 natively.

  To be sure, save reboot and wr mem.

• Question of VLAN native of UCS

  All,

  I have a problem that I can not just wrap my mind autour.  We have UCS setup in a lab with 2 interconnections connected to 2 nexus switches 5510.  The nexus switches are passed to the network via a Switch 4900 m.  All circuits are configured and tested as functional. All routing is configured and confirmed.  I have a problem in UCS, which is confusing to me.  In the lab, I kept the VLAN native to the vlan1.  I have the Setup VLAN 2-10 on all switches test and interconnections.  I created a service profile that contains 1 network card and placed it in the VLAN 7.  I installed Windows 2008 on a blade using this service profile.  In the operating system I statically IP'ed the NIC for the schema used in VLAN 7.  The OS, I cannot ping another device located in the vlan 7.  Also, I can't ping a host on a different VLAN.  If I place a check on the VLAN 1 as the vlan native I still cannot ping anything.  If I place the audit for vlan native to vlan 7 I can ping hosts in the same vlan, as well as outside of the vlan.  So why should I place vlan 7 as the vlan native when all my boxes are set up in the vlan 1 is the vlan native?

  Thanks for any help,

  Ken

  Ken,

  When you allow some VLANs on your Service vNIC profile you will need to set the VLAN native. This is because the way you have configured currently you are only "allowing VLAN 15', but you're not marking it.   It will work fine for ESX or Linux which allows to assign the dot1q tag to the host.  With Windows unless you have specific drivers doing the marking for you, you will need to do it at the level of the vNIC in UCS.

  Two ways to see this in action.  When you create a service profile in the 'Basic' - not 'Expert' method, you will need to choose a single VLAN for your interfaces.  This will treat interfaces about like an "access Port".  Conversely, when you use the "Expert mode you select the vNIC as a trunk, in which you" will allow to "all VLAN you acceding them as to, like this is the method you did.»

  For a Windows operating system, set the VLAN natively for the VLAN you want to access and you'll be gentle.  Unchecking this option button that "VLAN native" is allowing traffic to cross out of UCS on the VLAN native VLAN 1, your network - it is therefore MAC appears on other fabric under VLAN1

  Kind regards

  Robert

• If vlan native between Trunk ports not configured so what happens?

  I have a network where two ports of junction are allowed vlan 9 but not native VLANs configured. will be affect performance?

  by default the vlan1 is configure the vlan native to assign a vlan on the interface different native

  switchport trunk vlan native xxx

  HTH

  Richard

• Change the order of VLAN native?

  Can someone refresh me please as to what the command is to change the VLAN native for the whole switch? (IE: not only on the trunk, I mean the default native for the whole switch). Thank you

  Can someone please refresh me as to what the command is to change the Native VLAN for the entire switch? (IE: not just on the trunk, I mean the default native for the entire switch). Thanks

  Hi Steve,.

  By default, there is only one VLAN for all ports. This VLAN is called by default. You can't rename or delete VLAN 1.

  If you're talking about a management VLAN is nothing else than a VIRTUAL local network that is used for managing in-band of the network switching devices.  To configure this on a switch, you must create a Switch Virtual Interface (SVI) that is mapped to this VLAN, and then assign this virtual interface an IP address.  On a Cisco switch, it would look like the following.

  Interface Vlan99
  IP 192.168.1.1 255.255.255.0
  No tap

  I also want to make something very clear.  Your management VLAN is not to be identical to your VLAN native.  Question, please make sure that they are different.  Your management VLAN must only carry the traffic of in-band management and should not be the default VLAN.  By in-band management traffic, I am referring to SSH or telnet (Although telnet is not recommended because it is not safe).  Traffic such as BPDUS, PagP, CDP, use the VLAN native who is the vlan 1. But if you change the vlan native then CDP, VTP/PagP will always use the vlan 1 but packages will be marked. Only DTP uses vlan native so if you have changed the vlan native then DTP would use the new VLAN to send images. With PVST + BPDUS of course run on all the VLANS.

  Hope to help!

  So useful note the position

  Ganesh.H

• Can't change phone IP auto macro smartport vlan native on SG200

  We have a few SG200 switches and I try to configure the macros Automatic smartport for the IP phone and IP Phone + Office. Every time I have change the macro and change the VLAN native to what I want (the VLAN voice is OK but not the vlan native, I want desktop computers to connect to), I click on apply, but it automatically changes the VLAN default native VLAN (in our case 1 VLAN). I'm trying to change it to VLAN 2. Any ideas why it won't let me change the VLAN native? I can change the VLAN native on others, such as switches, routers, printers, comments, etc., but not the two above and the desktop as well. These three will not change for some reason any. Thank you!

  Hi Brademeyer29,

  what you see, unfortunately, this isn't a matter of configuration. This was reported to the engineering team and should be fixed in the next firmware version 1.4.1.

  For now, you will have to use the solution as not changing not VLAN native or not use smartport.

  Kind regards

  Aleksandra

• Enable the VLAN on sub interface internet access but block traffic to VLAN native

  I have a 2821 router w / MLS 2024 switches.  Native VLAN(default vlan) is my private network and VLAN 100 is my comments system.  Below is my interface config...

  interface GigabitEthernet0/1

  Description ES_LAN, ETH - LAN$ $$

  IP 10.1.0.2 255.255.0.0

  penetration of the IP stream

  IP nat inside

  IP virtual-reassembly

  automatic duplex

  automatic speed

  !

  !

  interface GigabitEthernet0/1.1

  encapsulation dot1Q 100

  IP 10.3.1.254 255.255.255.0

  penetration of the IP stream

  IP nat inside

  IP virtual-reassembly

  !

  IP default-gateway xx.xxx.xxx.xxx

  IP forward-Protocol ND

  IP http server

  23 class IP http access

  local IP http authentication

  IP http secure server

  IP http timeout policy slowed down 60 life 86400 request 10000

  Default route is defined...

  IP route 0.0.0.0 0.0.0.0 xx.xxx.xxx.xxx

  Access list are...

  access-list 175 deny ip 10.1.0.0 0.0.255.255 10.2.0.0 0.0.255.255

  access-list 175 allow ip 10.1.0.0 0.0.255.255 everything

  access-list 175 deny ip 10.3.1.0 0.0.0.255 10.1.0.0 0.0.255.255

  access-list 175 allow ip 10.3.1.0 0.0.0.255 any

  I want to continue to have access to the guest VLAN in VLAN private to allow the management of points of access etc.

  I want to allow internet access as guest newtork but block it to access my private network.

  Don't know how to do in this regard.  I tried to change the ACLs (remove the 10.3.1.0 entries) and creating an another acl for the Scriptures and applying that VLAN 100 sub interface... so far without success.

  Thanks in advance for the help!

  Hello Chris,

  > From this point of view should I leave the above lines and create another list acl for the 10.3.1.0 of the network and apply entering gig0/1.1?

  I would go this way, as in a simple ACL, you can't express your needs. The ACL to apply on gi0/1.1 will probably need further instructions then the ones I suggested, but divide the problem into smaller manageable pieces is a good strategy.

  > Also with this config would be NAT be performed on each network by making this change?

  Until the internal network and network of comments are on the same side (ip nat inside) there is no NAT triggered in communication between them so that you should not influence the NAT configuration with this change.

  Hope to help

  Giuseppe

• Native web services in Oracle 11 g

  Y at - there no official explanation on how to configure and create native web services to Oracle 11 g and how to properly secure these services? Since Oracle APEX now supports web services use SOAP and REST, it makes sense to have more explanation on creating and securing web services. As know many PL/SQL programmers, it isn't always an easy task to develop web services in jDeveloper to work with databases - with all of these technologies to Add on as jPublisher/Toplink to get the job of things. It is not easy to get the 'How to' guide on creating and securing of the native web services in Oracle 11 g.
  
  Thank you.
  
  Andy

  Hello.

  If you are still looking for this answer, you can try this.

  http://www.Oracle-base.com/articles/11g/native-Oracle-XML-DB-Web-services-11gr1.php

  The article has links to documentation and other resources at the bottom.

  See you soon

  Tim...

• Native Web Services database: XMLTYPE parameter in PL/SQL with XMLSCHEMA?

  Hello
  
  I would like to build a function with a parameter of XMLTYPE is the schema of the base, something like this:
  
  CREATE FUNCTION xy (p_xml XMLTYPE XMLSCHEMA 'http://myschema.com')...
  
  For now, I do the following code inside:
  
  l_xml: = p_xml.createSchemaBasedXML ('http://myschema.com');
  l_xml.schemaValidate ();
  
  / * validate XML with XSD code * /.
  l_nbr: = l_xml.isschemavalidated ();
  
  Why I want to put the schema directly in the statement is I want to use this function as a Web Service native Oracle. The web service does not know that the structure of the xml parameter because the schema is not known in the statement.
  
  Thank you and best regards,
  Andreas
  
  Published by: mdrake on November 8, 2009 21:55

  At the present time there is no way for the WSDL generated by the Native Web Services database to incorpirate this information. The problem is that there is no way to associate an XML schema to a variable value, parameter or return of PL/SQL. It should be the work of the XML DB and the PL/SQL to achieve group. It will consider a request for improvement.

  Workarounds only that I can think of would be to have a separate WSDL (made by hand) for this service. Of course, this will have to be to some other URL as expected, so this may not be viable, or to provide your own get (extended) WSDL service as part of the package, which adds the schema information in the WSDL. The Web Service consumer then you have to get the base/orawsv/parcel WSDL? WSDL, then get the WSDL extended by callling the appropriate method on the packaging...

• 2 PCs, PC2 connects via connects the PC1 wireless Internet wireless, network sees home, but will see no internet except with ethernet cable - illogical!

  1 computer (PC1) running Vista, to date, AVG free, Spybot S & D the timer running
  2 may have been infected with spyware by surfing - received message in the Explorer to search for the virus, think it was fake
  3 then lost wireless internet in the two IE & Firefox
  4 but had a Skype conference call minutes 40 OK - Bizarro
  5 lit (PC2) laptop running Windows (light version) 7 - same problem with browsers
  5A AVG on PC1 has been updated - ran a deep analysis, found 44 spywares & fixed them
  5 b also ran registry cleaner
  6 has managed to update Spybot, is all business, then working browsers, internet connection complete
  7 can now connect 1 PC to internet with ethernet connection, he can see the wireless and home networking (local access only) so I guess the wireless work, but he can not see the internet on this subject.
  8 update both Spybot and AVG on PC1 with wired ran the two found no additional infection
  It's really strange, I do not understand how to see PC2 PC1 and PC2 connected wireless to wireless home, but PC1 is unable to connect to the internet without a network cable...
  All pretty useless Windows diagnostics

  Hello

  A message in the small window that says connected wireless does not mean that you really have a valid functional connection.

  Linking the means of router you can enter the IP base of the router in an address bar in one go, being able to connect, see and configure the router menus (extended to the wireless router manual should explain how to do).

  If it will not connect to your wireless router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.

  Enable security wireless after you eat to make a functional connection.

  ----------------------------

  The wireless card drivers much also install utility wireless of the seller.

  To ensure that if there are utility wireless isn't running with the native Windows wireless utility provider (Service WLAN).

  ----------------

  Firewall software can block traffic Local to the network that you are trying to use because it is not set to the network Zone Trust.

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible set up the firewall correctly, otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.

  If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  party like Hello and NetMagic 3rd network managers can block local traffic too.

  ---------------------------

  Stack TCP/IP (network IP number) of work should look like.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

• Question of vlan Cisco 7600 PFD

  Hello!

  Please help with a question.

  In our network, we have 7600 and I need to create a service of vpls with two different VLAN associated with a PFD:

  L2 PFD manual test
  VPN id 100
  neighbor 1.1.1.1 mpls encapsulation

  interface Vlan120
  no ip address
  Shutdown
  PFD xconnect tests
  !
  interface Vlan121
  no ip address

  And when I try to reach "xconnect PFD testing:

  Incompatible with the PFD configured setting.
  Check the interface MTU, VLAN ID size
  Or try to configure BPDU PW on routed SVI, which is not allowed

  Is it possible to do or not? No mapping VLANs etc.

  Thank you all!

  Hi Dimitri, you can do it, but the link is made to port vlan does not level level IVR.

  Here is a configuration snippet:

  the GigabitEthernet4/1/0 interface

  101 ethernet service instance

  encapsulation dot1q 101 second 10

  rewrite the penetration pop tag 2 symmetrical

  interface GigabitEthernet4/1/1

  ethernet 100 service instance

  encapsulation dot1q 100

  rewrite tag pop 1 symmetrical penetration

  connect GigabitEthernet4/1/0 eline-101 101 100 GigabitEthernet4/1/1

  Xander

• 891 router - no IP on VLAN 2

  Hi all!

  I am) very new to all this and I have to configure a router cisco 891. So far I was doing ok but I have a problem to connect devices on the vlan 2.

  I don't want to assign vlan according to the port, the devices are able to score their own packages.

  For the moment, when I connect a 'classic' device, it will on the vlan 1 and get an ip address from my pool vlan 1. Very well. Problems begin when I tell the device to mark his package as belonging to the vlan 2. As soon as I do this, I just can't get any address from my dhcp assigned IP.

  Here is my config file, someone has an idea? :)

   Building configuration... Current configuration : 2978 bytes ! ! Last configuration change at 14:20:32 UTC Thu Oct 15 2015 by tchavrier version 15.3 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Cisco891 ! boot-start-marker boot-end-marker ! aqm-register-fnf ! enable secret 5 XXXXXXXXXXXXXXXXXXXXXXXXX enable password XXXXXXXXXXXXXXXXXXXXXXXXX ! no aaa new-model ! ! ! ! ! ! ! ip dhcp excluded-address 172.26.1.1 172.26.1.49 ip dhcp excluded-address 172.26.1.100 172.26.1.254 ip dhcp excluded-address 10.10.10.1 10.10.10.49 ip dhcp excluded-address 10.10.10.100 10.10.10.254 ip dhcp excluded-address 10.10.20.1 10.10.20.49 ip dhcp excluded-address 10.10.20.100 10.10.20.254 ! ip dhcp pool vlan1pool network 172.26.1.0 255.255.255.0 default-router 172.26.1.254 dns-server 208.67.220.220 ! ip dhcp pool vlan2pool network 10.10.10.0 255.255.255.0 default-router 10.10.10.254 dns-server 208.67.222.222 ! ip dhcp pool vlan3pool network 10.10.20.0 255.255.255.0 default-router 10.10.20.254 dns-server 208.67.222.222 ! ! ! ip cef no ipv6 cef ! ! ! ! ! multilink bundle-name authenticated ! ! ! ! ! ! ! license udi pid C891F-K9 sn FCZ1939917U ! ! username XXXXXXXXXXXXXXXXXXX privilege 15 secret 5 XXXXXXXXXXXXXXXXXXXXXXXXXXXX. ! ! ! ! ! no ip ftp passive ! ! ! ! ! ! ! ! ! ! interface BRI0 no ip address encapsulation hdlc shutdown isdn termination multidrop ! interface FastEthernet0 ip address dhcp ip nat outside ip virtual-reassembly in duplex auto speed auto ! interface GigabitEthernet0 no ip address ! interface GigabitEthernet1 no ip address ! interface GigabitEthernet2 no ip address ! interface GigabitEthernet3 no ip address ! interface GigabitEthernet4 no ip address ! interface GigabitEthernet5 no ip address ! interface GigabitEthernet6 no ip address ! interface GigabitEthernet7 no ip address ! interface GigabitEthernet8 ip address dhcp ip nat outside ip virtual-reassembly in duplex auto speed auto ! interface Vlan1 ip address 172.26.1.254 255.255.255.0 ! interface Vlan2 ip address 10.10.10.254 255.255.255.0 ! interface Vlan3 ip address 10.10.20.254 255.255.255.0 ! interface Async3 no ip address encapsulation slip ! ip forward-protocol nd ip http server ip http authentication local no ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ! ip flow-top-talkers top 10 sort-by bytes cache-timeout 60000 ! ! ! ! control-plane ! ! ! mgcp behavior rsip-range tgcp-only mgcp behavior comedia-role none mgcp behavior comedia-check-media-src disable mgcp behavior comedia-sdp-force disable ! mgcp profile default ! ! ! ! ! line con 0 no modem enable line aux 0 line 3 modem InOut speed 115200 flowcontrol hardware line vty 0 4 privilege level 15 password haricotmarteaulitjaune login local transport input telnet transport output telnet line vty 5 15 password haricotmarteaulitjaune login local transport input telnet transport output telnet ! scheduler allocate 20000 1000 ! end

  Thank you!

  Hello

  If your devices are marking their own packages (IE VLAN2) then the switchport will reject the.

  Without any explicit configuration on the switchports, they will be configured with native VLAN1. This means any packet received on that switchport who doesn't have a tag of VLAN is tagged with VLAN ID 1. All packages with tags will be ignored, but since you have not configured for trunking they will be discontinued.

  To make it work, you must add the following:

   ! int range gi0-8 switchport trunk native vlan 1 switchport trunk allowed vlan all !

  This would allow to the unmarked packages be sent (VLAN1), but would also treat packages that are being scored by connected devices (providing configuring VLANS exist on the router).

  Hope that helps.

  see you soon,

  SEB.

• Using VLANs with Cisco 1240AG

  Hi guys,.

  NIC 1

  I want that all cable customers (PC1 to PC9) in native VLAN 1 and all in VLAN 10 wireless clients.

  

  1. is this a correct network card?

  2. given that all the wireless clients are in the same VLAN, I guess I should configure port F0/10 market as a port of access for VLAN10 and the single trunk port would be F0/0 that goes to the router. And all I have to do is create VLAN 10 access point and map it to an SSID. Am I wrong?

  3. do I need to do any configuration regarding native VLAN 1 on the access point at all?

  Network card 2.

  I want to have customers invited LAN wireless as well.

  

  1. is this a correct network card?

  2 the port configuration of the ethernet switch to which is connected the point access (F0/10) as a TRUNK port?

  3 configure the APs as a trunk port ethernet port?

  4. can you explain these two commands for me?

  AP(config-subif)# interface FastEthernet0.10AP(config-subif)# encapsulation dot1Q 10

  Hello

  Yes you are right!

  If you want to configure only one SSID and only one VLAN, then make the Switchport access and for multiple SSID make as a trunk on the switch and the AP configure interfaces corresponding Sub...

  Here is the doc that i hv written can give you some nice info as well!

  https://supportforums.Cisco.com/docs/doc-14496

  Let me know if that answers your question and please do not forget to note the useful messages!

  Concerning

  Surendra

• Question of VLAN by default and best practices

  Hi all

  I recently read on VMwares ESX Server 802. 1 q-paper Solutions of VLAN and came across the following article:

  Question of VLAN native (aka "VLAN1 Issues")

  "VLAN native is used to switch protocol management and control.  Native frames of VLAN is not VLAN ID tag in many types of switches, and in which case the trunk ports implicitly treat all frames not marked as frame VLAN native.

  VLAN 1 is the native VLAN ID by default for most Cisco switches.  However, in many enterprise networks, the VLAN is the VLAN 1 or 100, it could be any number depending on your configuration of switch type and running.

  It is common recommended to avoid using some VLAN native (often the VLAN 1) for any regular data traffic.  VMware recommends that you not associate any group native virutal server ESX VLAN VLAN ID switch port.  Also, so that you avoid them VLAN native for your groups of ports VLAN, no native VLAN related configuration is required on ESX Server systems. »

  That being said, I know a lot of people and more small to medium-sized networks leave light network VLAN by default.  If this is the case it would be better to change the entire network switching to one VLAN different and then put groups of ports on the same VLAN?  Or is the problem with the default VLAN really does not impact?

  Hello

  You have quite a few involved networks when you use virtualization and some I would classify as a virtualization host networks: the Service Console, VMotion, storage over IP.  They are more likely on separate networks of your VM network traffic... At least use VLAN to do this.

  See http://kensvirtualreality.wordpress.org for a good series of articles on virtual networks.

  Best regards
  Edward L. Haletky
  VMware communities user moderator, VMware vExpert 2009, Analyst of DABCC
  ====
  Now available on Rough Cuts: ' VMware vSphere (TM) and Virtual Infrastructure Security: ESX security and virtual environment '
  Also available "VMWare ESX Server in the enterprise"
  SearchVMware Pro| Blue gears. Top virtualization security links| Security Round Table Podcast virtualization