Mix the virtual switch different type in a Cluster and a data center.

Similar Questions

• How to leave the virtual switch as a physical switch law in esxi 5?

  Hello.

  I have Esxi5 installed on a server with 3 physical network card (they are supported and found in Esxi) on that Esxi I installed a virtual-SIN (NexentaStor) machine. The first network adapter is connected to the router, the second network adapter is connected to a PC. DHCP is enabled on the router. Normally on a real switch all connected pc should automatically get an IP address from the server (router), or must be able to communicate when they have a fixed IP address. This does not work on the virtual switch. One of my virtual pc Gets an IP address in a range of false, and I can't connect a real PC at this switch

  2 questions:

  1. Should what settings I use in esxi5 to get virtual pc the good IP address?
     
  2. Is it possible to connect a real pc directly to the second NIC in my esxi server and use the virtual switch as a true switch? In this way, I can use the Gigabit Nic for a fast and direct connection to the virtual NAS and can connect to the internet via the switch?
     

  

  Any help would be appreciated

  Pieter

  ESXi does not NAT unlike VMware Server or Workstation/Fusion.

• Changing the virtual switch name

  Hello

  Is it possible to change the name of the virtual switch, for example, when you create a new vSwitch in VI Center it starts with vSwitch1 can change you it to vSwitch2 providing their isn't another switch with this name?

  Thank you

  you change the esx.conf you need to reboot (be sure and create a backup of esx.conf... /etc/vmware/esx.conf_backup /etc/vmware/esx.conf cp)

  If you found this information useful, please consider awarding points to 'Correct' or 'useful '. Thank you!

• I get a message saying "you have exceeded your profile storage space. Yet all the files listed th are actually my docs and application data. How to delete my profile, but not from my pc? increase the max profile size

  I get a message saying "you have exceeded your profile storage space. Yet all the files listed th are actually my docs and application data. How to delete my profile, but not from my pc? increase the max profile size

  1. the first thing to do is to make sure that the computer is completely virus/malware-free. Googling around this error produced quite a few links where the posters were or had been infected with Spyware Protect 2009 rogue.

  http://www.elephantboycomputers.com/page2.html#Removing_Malware

  Once the scanning is complete (do not skip the preparatory stages no more), if the problem persists:

  2. double-click on my computer, right-click the icon for your hard drive, click left to get its properties. If you see options to set Quota management make sure that they are disabled.

  3. in the case - BUT ONLY AFTER YOU ARE sure THAT THE MACHINE IS MALWARE/VIRUS-FREE - copy the lines between asterisks (not including the asterisks) below and paste it into Notepad. Save as undopolicy.reg somewhere, you will find. And then double-click the .reg file, that you have just made to melt in your registry. I hope that this will take care of the issue.

  *****
  Windows Registry Editor Version 5.00

  [HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\System]
  'EnableProfileQuota ' = -.
  'ProfileQuotaMessage ' = -.
  "MaxProfileSize" = -.
  'IncludeRegInProQuota ' = -.
  'WarnUser ' = -.
  'WarnUserTimeout ' = -.
  *****

  MS - MVP - Elephant Boy computers - don't panic!

• How to get the specific information of hardware and software data center

  How to get the specific information of hardware and software data center with powercli...

  What kind of information you need?

  No matter what Esxi host hardware info., if so could below thread is useful.

  Information about the host material with information on the nic and HBA drivers

• Network management - only the virtual switch

  I installed latest ESXi 4 Update 1, which is available. I m running Active Directory LAB on several virtual servers Windows 2008 R2 and one of them acts as a router with RRAS role. I m creating 3 different subnets and one of them must be only virtual - no material connection NIC in the interface of ESXi´s it seems that I can't do this, while creating the new switch virtual it forces me to select NIC it becomes a problem, because if I use a virtual switch for Windows 2008 router has the physical NETWORK map It will come to mean that the cable is disconnected. And I need a virtual connection between virtual servers only, that they will be the single subnet between them and communication to physical clients will go through this router´s of Windows 2008 NIC that is not supposed to be physical.

  How can I archive with ESXi?

  You can create a vSwitch without attached Teddy.

  Do not select any NIC, or delete them after the creation of the vSwitch.

  André

• Initializing the elements of the array to different types of data

  Hello!

  Receiving data sring and write it in the table. Shot data consist of different types of data, so now I have to initialize my element of berries somehow to correct the data type. Table example:

  char

  char

  int

  int

  float

  float

  Is it possible somehow? Or should I use the formula node or something like?

  Thank you! (new)

  These data resembles a cluster to create a cluster, you can create a constant of cluster on the comic book and use the cast function to fill in the cluster. Some things you need to be aware of:

  What is the size of the Int?

  What is the size of the float?

  What is SSE-endian data.

  Here are two examples:

  

  Tone

• FDMEE charge in terms of the planning of different Types (SEEP)

  How can you tell FDMEE what Type of Plan of loading when you have two different types of plan in the planning?

  I am currently on SEEP (budget planning Cloud System).

  Found.  In the rule of load data under the drop-down list of the Type of Plan.

• Assign comments NIC to the virtual switch / Portgroup

  All,

  After many search on these forums and the API reference guide, I can not find a solution to the following problem, we are going to have...

  We use the Perl SDK to clone existing Virtual Machines and create new virtual switches and exchanges. However, what we can't understand is how to assign a NETWORK adapter on a virtual computer for the new virtual switch / Portgroup.

  We would like to be able to create two new virtual machines and a new switch and add the two virtual machines to the portgroup on the switch so that they can communicate. At a later stage, we also want to be able to add a physical NETWORK card from the host to the new switch.

  The making through the vSphere Client is quite simple, but we need to automate the task.

  No indication on what we should do is appreciated. If it's easier to do using other APIs (such as Web Services), we are open to try this instead...

  Thanks in advance,

  Andy

  Take a look at this script as an example on how to upgrade ports of an individual vNIC GRPE - http://communities.vmware.com/docs/DOC-10112

• The virtual switch configuration

  Hello

  I configured Vswitch on ESX4.0 connected with a teddy bear.

  There are Cisco catalyst 4503 L3 switch configured with several VLANS at the other end. I have configured the switch port trunk with dot1q encap mode that ends on the ESX4.0 server. Service console is configured with IP default VLAN, which is accessible from the other VIRTUAL networks. One of the virtual machine with Win2k3 OS is installed, but after configuration, I am not able to ping default gateway of VLAN respective or any other property intellectual VLAN.

  Can anyone guide me where I go wrong and how to correct the problem?

  Set the Group of ports to the VLAN specific you want the virtual machine to be on.  Do not put any VLAN ID in the virtual machine, just plug it into the port group.  If you have other virtual machines, or other on this virtual machine network interface cards that need to connect to the other VLAN create other Port groups for each VIRTUAL local area network required.

• How to set up the virtual switch vmnet0 so in fact, it behaves like a switch.

  Hello

  I have a problem:

  My configuration is:

  host of CentOS 5.3 using vmware server 1.06

  3 clients (all centos 5.3 with vmware tools) installed

  web01

  DB01

  backup01

  The three guests have public ip and use the bridged (vmnet0) network

  The backup01 backups web01 and db01 every night.

  My supplier can see that traffic on its poort switch that connects the host to the internet, and he wants to charge me for it.

  The three guests (and host) are all on the same subnet. It is the local subnet traffic that does not use a gateway.

  It seems the traffic between hosts is diffuse on my physical eth0 on the host. When I have some files between guests, it also appears on the page from my supplier of PCs followed AY. (Just likecommunication between 2 physical host computers are on the local network when you use a hub instead of a switch)

  I thought it was probably the only way to vmware would work when using network bridges. Because the host doesn't know anyting on the clients ip numbers.

  But when googleling abot this I found several docuemtents (for vmware server 2) telling me that vmnet0 is actually a sort of virtual switch.

  If this is true this virtualswitch should know other mac adressess clients (arp who a..) and she must stop the internal traffic to leave the material.

  Is not what is happinging. It looks more like a virtualhub instead of virtual switch.

  So I was wondering if there are ways to configure the vmnet0 somehow. I was hot, but I can't find anything about it.

  I don't want to change the bridged mode or coz internal use of the intellectual property of the plan is to spit the separate web01 and db01 to vmware guests in the furture.

  Does anyone have any suggestions?

  My idea was to put an additional physical switch between me and my switch to suppliers, but that seems to be a ridiculous solution.

  Any help is welcome.

  Concerning

  Hans Groot

  VMserver don't use virtual switches: it uses virtual hubs. They are mislabeled - probably because "virtual switch" sounds more sexy than "virtual hub".

  You can't change their behavior to be more like a switch

  ___________________________________

  VMX-settings- VMware-liveCD - VM-infirmary

• change the virtual switch to the virtual hub

  Hallo,

  all the networkadapters are virtual switch. How can I change to a hub? I'd like to sniff my networktraffic with a guestsystem, but that only works with a hub. Or can I change some settings to do this with esxi?

  version: ESX Server 3i, 3.5.0 110271

  MfG

  Mario

  You can set it on a vSwitch or Portgropup

  Click Edit, switch or PG-> Security-> Promiscous Mode-> accept

  Take a look at the Config Guide http://www.vmware.com/pdf/vi3_35/esx_3/r35u2/vi3_35_25_u2_3_server_config.pdf

  If you also want traffic on your pSwitch, you create a mirror on your pSwitch port.

• Security on the Virtual Switch

  We have a web layer and a layer of app in our environment.

  An ESX host would have a VLAN to the web layer connection and another with the application layer. Well separated and in line with our security strategy.

  We have a separate vlan for backup. Layer Web and application can share the same network card on the vlan for backup.

  Problem is that it can communicate with each other through the EPS backup because he won't have the physical switch when in the same ESX host. He speaks just internally within ESX.

  Does anyone know if there is a setting in ESX forcing traffic to go to physical swith before talking to another virtual machine on the same host?

  Hello

  See http://itknowledgeexchange.techtarget.com/virtualization-pro/how-traffic-routes-between-vms-on-esx-hosts/ for how routes traffic. If the virtual machines share the same portgroup on the same vSwitch traffic is not routed outside ESX otherwise it's almost always. Check out the blog for more details.

  Best regards

  Edward L. Haletky

  VMware communities user moderator

  ====

  Author of the book "VMWare ESX Server in the enterprise: planning and securing virtualization servers, Copyright 2008 Pearson Education.»

  Blue gears and SearchVMware Pro Articles: http://www.astroarch.com/wiki/index.php/Blog_Roll

  Security Virtualization top of page links: http://www.astroarch.com/wiki/index.php/Top_Virtualization_Security_Links

• How to mix the layers in different proportions?

  I want to merge two layers together in a 2:1 ratio. that is the final result consists of a 66.66% and 33%. There are real black in the image. Should what settings I set to achieve this merger? I tried a lot of parameters, but impossible to get blacks unless I use levels as well.

  A test image, that I'm trying to mix can be downloaded here: http://www.mediafire.com/download/b38myfw3ly5daah/Test_Blend.tif

  Thank you

  Try this technique of the brand pile

  

• Problems with the revival of NIC in the virtual switches

  We have implemented a vlan trunking and during the installation, I found some, but not all of my cards are not detect a 'down' State in vmware. I have tried rebooting all equipment and it did not help. I double checked the configurations, and they are the same, I see. I was wondering if anyone has had problems with this.

  In the picture below I would normally see a red X in the State of the NETWORK adapter binding after a few moments, and the other NETWORK adapter will pass traffic. On 5 configured hosts, this seemed to be the only NIC that is not down to the virtual center when I stopped the switchport. Then when I restarted the swtich, I checked 5 guests for the correct path failover. Strangely, my other hosts 2 has actually detected the card NETWORK went down but the failover does not occur and the virtual machine went unresponsive to the outside world, even if their State of link does show and X! Failover detection is set to bind the State.

  All but one host is 3.5.64607, the other is 82663. My next step is to update and bring it to past versions. I hope that this will work.

  Hello

  I had this same problem with my HP and mezzanines of broadcom cards blades.  After many hours with tech support, we realized that this patch fixed: ESX350-200802401-BG.

  Hope that helps!

  Kelly Burton

  COMPUTER systems engineer

  Banner Health