Model problem

Similar Questions

• Compaq presario c795tu model - problem IDE hard drive /disques

  Hello please help me... In my laptop model no presario c795tu, I found some virus a few days ago and I removed it. From here only, my laptop gives error windows repair and SATA / IDE hard disk error.

  Whenever I connect to my laptop. All data are accessible, but it is automatically hidden.

  It gives the error 4 - 5 times this system has a problem in IDE / Sata hard disk. Kindly it reboot and it restarts automatically.

  Please help me how I can solve my problem.

  Diakite says:

  Hello please help me... In my laptop model no presario c795tu, I found some virus a few days ago and I removed it. From here only, my laptop gives error windows repair and SATA / IDE hard disk error.

  Whenever I connect to my laptop. All data are accessible, but it is automatically hidden.

  It gives the error 4 - 5 times this system has a problem in IDE / Sata hard disk. Kindly it reboot and it restarts automatically.

  Please help me how I can solve my problem.

  Press the power button and then press the F10 key to access the BIOS. Run the hard drive Diagnostics. What I saw in my investigation shows it's a 160 GB SATA hard drive.

  There are a few ways that you can use to solve the problem.  You can try the online scanner of ESET.com to remove the offending code or you can try Malwarebytes. MalwareBytes is recommended by some members of the forum, and there is a free version. The ESET online scanner is also free. I prefer the ESET online scanner.

  The simpler but more radical solution would be to make a recovery to factory state using the HP Recovery Manager. You should be able to access the market with the F11 key recovery manager. If this isn't the case, you can use your set of recovery disks. The downside of the HP recovery solution is that you will lose all data and programs you have on your laptop. advantage is that everything works again once you have installed the drivers.

  Best regards
  ERICO

• Three-phase engine model problem AC...

  Hello, is it possible to use the 3PH_Motor of the family OUTPUT_DEVICES located in the Electro_Mechanical group but with a model modified to Spice that uses only the data printed on the nameplate? I ask this question because I simulate the power factor correction using a field of 10 engines rated at 110 kW each, for my thesis, but I need to the R and L of the windings in order to use the default template and I can't find these values in the catalogues.

  Thank you in advance and I hope that there is a way to solve this problem...

  I guess that you are looking for an induction motor.

  It would be simplistic to model a with a fixed R, support the induction motor (in the Multisim V12 we actually removed the 3PH_Motor and added instead a more realistic dynamics model based on a more realistic set of parameters). An induction motor is in many ways like a transformer. Therefore, you must the inductance of magnetization, inductors of leak of the rotor and the stator and rotor and the stator resistance. You may be able to contact the manufacturer to obtain, but I doubt that you can accurately their inferred only from the nameplate.

  This link goes on a simple equilibrium model: http://www.scribd.com/doc/13311930/Induction-Motor-Modeling-steady-State

  Thank you

• Custom report model - problem with summary

  Hello

  I've created a report with the custom template.  Everything seems okay except that the 'Sum' section (marked in red below) containing the header entries.  I think, I might have placed the scripts in the wrong places bu tnot able to understand.  What I expect is, the total value of the 9,920.00 show with label - "Total: '."

  

  Only under sections are filled in the template, the rest is blank.

  Line 1 a - model

  <tbody>
  <tr> <th>Receipt No.: <td id="rpt_no" colspan="2">#RECEIPT_NO# <th id="rpt_dt">Receipt Date: <td>#RECEIPT_DATE#
  <tr> <th>Description: <td colspan="4">#DESCRIPTION# </br> #CHQ_DD#
  <tr> <th id="tab_head">A/c.CODE <th id="tab_head" colspan="3">HEAD OF ACCOUNT <th id="tab_head_amt">AMOUNT
  <tr> <td>#ACCOUNT_CODE# <td colspan="3">#ACCOUNT_NAME# </br> #INSTALMENT# </br> #PARTICULARS# <td class="num">#AMOUNT#
  

  Line 2 - model

  <tr> <td>#ACCOUNT_CODE# <td colspan="3">#ACCOUNT_NAME# </br> #INSTALMENT# </br> #PARTICULARS# <td class="num">#AMOUNT#
  

  Front lines-

  <div class="report-1" #REPORT_ATTRIBUTES# id="report_#REGION_STATIC_ID#">
  <table>
  <tr>  <th id="comp-name" colspan="5">&G_COMPANY_NAME.
  <tr>  <th id="comp-adr" colspan="5">&G_COMPANY_ADDRESS.
  <tr>  <th id="comp-adr" colspan="5">&G_COMPANY_PHONE.  &G_COMPANY_EMAIL.
  

  After the lines-

  <tbody class="uReportPagination">
        #PAGINATION#
    </table>
    <div class="CSV">#EXTERNAL_LINK##CSV_LINK#</div>
  </div>
  

  Please let me know how to solve my problem.

  Thank you and best regards,

  -Anand

  anand_gp wrote:

  And Yes, it is built in formatting of column sum-

  Who does not work with a named column template customized. You must calculate the sum in the report query and place the result in the report by using another conditional model.

  See the sample application I've created in your workspace apex.oracle.com.

• ESXi network model problem

  If I'm trying to deploy a model of esxi 4 I imported LM4. No problem with importing or deployment,

  However, when I deploy the model he has no connectivity ip else VM deployed in its closed working space. I saw that in the properties vmware tools has been set to 0. Other virtual machines are listed as 8290. If a virtual machine in a workspace has no installed vmtools is the expected behavior?

  It is, of course, you need to check if you have assigned good system Adpapter for the model, you must deploy and install vmware tools, then you will get a valid n/w adapter for the virtual computer.

  Kind regards

  Jana.

  NOTE: If your question or problem has been resolved / answered, please mark this thread as answered and awarded points accordingly.

• data model problem

  I have the following code in my Flex application:

  model.userStatus = new Collection ArrayCollection (event.result as Array);

  model.userStatusSel = new Collection ArrayCollection (event.result as Array);

  addAlltoFilterList = new Object();

  addAlltoFilterList.CustCnt = 1;

  addAlltoFilterList.UserStatCnt = 0;

  addAlltoFilterList.UserStatus = ' All the ' ;

  model.userStatusSel.addItemAt (addAlltoFilterList, 0);

  The problem is when I add the word 'All' to model.userStatusSel, it is also added to model.userStatus. Can someone tell me why or how I can add the word "All" to a datamodel, but not a? I use these data in a ComboBox on several different forms. In one place I use it as a filter and want the word 'All' to appear. A different form I use it as a selected user data entry and do not want the word "All" appears. Thanks in advance for the help!

  Have an ordinary day...

  Kurtis ~ |  :-)

  Try this:

  model.userStatus is new ArrayCollection (event.result as Array) collection;.

  model.userStatusSel = new ArrayCollection (model.userStatus.toArray ());

  Who must break the link between the two, which are established, because you use event.result for both.

  If this post answers your question or assistance, please mark it as such.

  Greg Lafrance - Flex 2 and 3 certified ACE

  www.ChikaraDev.com

  Flex / development, training, AIR and Support Services

• Alignment of RTF model problem

  Hello
  We have created a Template.The RTF template contains the following hierarchy.
  First of all, it displays the name of the manufacturer:
  then the list of the ModelTypes
  The column heading is date. So for every week we will be divided like a group.so, we weekdata first, second week
  data like this. Totally, we have 13 weeks.
  
  Now the problem is for each model, we have 28 rows of data.
  I want to print two templates/page(Number of rows are not equal in all cases because if new manufacturer start then one row is increased). In the output (pdf) I get the first model perfectly for the second model
  I get the last row in the page.similarly next to the remaining pages. Total, we conduct a
  about 150 pages.
  Is there any way to limit the page for data of two models only.
  
  
  
  Thanks in advance.

  Hi Andre,

  To limit the number of models per page, you first create all the basic details of the model in a single table and then put this table in another table with a line and a column.after that you must change the property of a table, in the properties of the table on the line tab uncheck the option allow splitting multi-page lines.

• Cloning of a model problem

  Need to create 1000 VMs based on one model and prefer not to do it manually.  I use the following script and it is a failure.  In addition, I need to specify the list of resources, which is not yet in my order.  Thank you.

  Script:

  $template = "acqpodad1temp".

  $NewVMName = "poc1.

  $datastore = "dsRTPVMware70000".

  $host = "rtpvhost73".

  $folder = "001.8.8.70HC.888 - ACQPOC".

  $rp = "001.70.888 - ACQPOC".

  Get-model "$template" | New-VM - VMHost "$host" - name "$NewVMName" - location (Get-folder "$folder") - data store (Get-data store "$datastore")

  Output:

  Impossible to replace host variable because it is read-only or constant.

  C:\VMware_Healthcheck\createvms2.ps1:11 tank: 6

  + $host & lt; & lt; & lt; & lt; = "rtpvhost73".

  Get-file: 2009-03-09 16:49:15 Get-file with the name "001.8.8.70HC.888 - ACQPOC" not raise

  searching by filter (s).

  C:\VMware_Healthcheck\createvms2.ps1:15 tank: 92

  + Get-model "$template" | New-VM - VMHost "$host" - name "$NewVMName" - location (Get-file & lt; & lt; & lt; & lt; '$f '.

  ore (Get-data store "$datastore")

  New-VM: cannot bind parameter 'rental '. Could not convert "" to "VMware.VimAutomation.Types.Folder".

  C:\VMware_Healthcheck\createvms2.ps1:15 tank: 79

  + Get-model "$template" | New-VM - VMHost "$host" - name "$NewVMName" - location & lt; & lt; & lt; & lt; (Get-file "$f

  ore (Get-data store "$datastore")

  Ouedraogo who is oke all.

  You can comment out or remove the following lines:

  #CREATE OBJECT CUSTOMIZATIONGUIRUNONCE

  $vmcSpec.Customization.Identity.guiRunOnce = new-Object VMware.Vim.CustomizationGuiRunOnce

  SPECIFICATION #GUIRUNONCE

  $vmcSpec.Customization.Identity.guiRunOnce.commandList = $PostInstall

  I have a previous post, I forgot to comment on the guirunonceobject

• Models: problems linking

  We need to re - attach a child page given birth from a template. When we try to do, the result is two sets of code for the sidebar and the content. Of course, then they are dubbed upward in the mode of creation resulting. Dialog box that need areas 'resolved' has been completed correctly.
  
  Appreciate your help in advance, David Allen

  Spawn a new child of the model. Copy and paste the content of the former to the
  New. Replace the old page to the new page when finished.

  --
  Murray - ICQ 71997575
  Adobe Community Expert
  (If you * MUST * write me, don't don't LAUGH when you do!)
  ==================
  http://www.projectseven.com/go - DW FAQs, tutorials & resources
  http://www.dwfaq.com - DW FAQs, tutorials & resources
  ==================

  "david_allen_mac" wrote in message
  News:gbd9pm$CSP$1@forums. Macromedia.com...
  > We need to re - attach a child page given birth from a template. When we try to
  > do
  > so, the result is two sets of code for the sidebar and the content. Of
  > course,.
  > while they are dubbed upward in the mode of creation resulting. The need for dialogue
  > areas 'resolved' has been completed correctly.
  >
  > Enjoying your help in advance, David Allen
  >

• Horizontal display of parents/children/grandchildren on model problems

  Hello
  
  I'm trying to display horizontally records children/grandchildren on my model. I can see the children/grandchildren records but not the Parent. I'm sure it's an easy fix, but it escapes me.
  
  I can send the template file and .xml .rtf to all those who would like to enlighten me.
  
  Thank you.

  Send it to my id profile.

• Editable with table/model problem

  Hello
  I'm having a strange problem with my page, and being new dreamweaver I don't know what is happening.
  I created a template for my Web site and the template seems to work ok, but in my editable region, I get a huge space in my table. I can't find the source of this gap, I went through the code but nothing is jumping on me as bad. It was built in Dreamweaver CS3 V9.0 Build 3481.
  You can view the page at http://fcwp.org/betapage.htm and I'm pretty sure you'll see what I'm going to talk right now. All have a guess at this problem?
  -Leif

  After reviewing the code once again, I see what you're talking about. I started cleaning up the page and his work/research better now (although I broke my menus spry in the process). Thanks for the help!

• Satellite Pro A300 he can't start WLan - Fn + F8 key problem

  Hello

  I have a wireless satellite pro a300-1nt model problem... I have instaled win7 ultimate (32 bit) and and all the Nice work, except that... in the household of wireless device is all ok, windows recognizes the card, he said all work perfectly... but when I try to start it, nothing happens. When I try to solve the problems they say "WiFi is disabled" and something like "Use the power switch on the front of the computer, or the function keys, if necessary activate wireless", but when I use Fn + f8 nothing happens...

  Now I don't know what the problem... don't know what to do... windows recognizes the card, but I can't start with buttons: (...) I have try all the drivers that I can find but nothing, if someone have similar problem or know something useful, please share... :(

  Thank you
  Aleksandar

  PS Sorry for the bad English

  Hello

  You have installed Win 7 but you didn t install some tools that controls the FN keys!

  You need to install the support card Flash Utility and added value package!
  You can find that both page European driver Toshiba Satellite L500 download area!

  PS: I think you should also check the BIOS settings. Some BIOS contains an option to toggle the wifi.

  In addition, go to-> properties Device Manager card Wlan-> Advanced tab
  Here, you can activate Wlan card too!

• Cable LCD Y560 replacement problems

  Hello good people of Lenovo forums!

  I have a laptop Y560 who has a damaged LCD cable (part no: "DD0KL3LC000"). Because of the hinge of this model problem, the LCD cable had caused the crazy screen flicker and inverted the colors.

  So I recently tried to replace one on ebay, but unfortunately it did not work... as when I inserted the new cable, the screen of the laptop does not work at all (without backlight or photo). The cable is labeled as "DDKL3DLC120" on its label, even though the ebay description was DDKL3CLC020, which is supposed to be the same as my original.

  Did I just took a wrong choice of the ebay seller? I think it should work.

  On my other problem... my power adapter seems to be wobbly after trying the new replacement cable - because my battery is cooler! Comments:

  • The Y560 off, with battery inserted, I connect the power adapter. The AC adapter led turns off and does not power up what I send to reconnect electric socket head.
  • Power adapter is plugged in. Windows CONSTANTLY tells me to plug my adapter, with this message in endangered (battery tray icon load again), then telling me to plug again. I also notice a slight flickering on my front right external LCD screen the following messages is displayed (my internal LCD is still drunk as stated above).

  • The laptop works fine on AC only without the battery inserted.

  The problem would be the adapter? and not the battery? If all goes well not something that is dead on the M/B?

  Thank you

  Problem. Solved.

  

• a 4550-G510 printing problem

  4550 - G510 prints test sheet OK, with standard printing head responds but no ink flow.  New black cartridge and no error message

  I'm two links. The first addresses the blank pages emitting printer or partial impressions. He will have to you look at the settings. Here is the link: http://goo.gl/sEIuz.

  The other link addresses print quality for your printer model problems generally. It will have you try the various troubleshooting steps that will try to solve quality results. This link is more for the quality of output of ink. http://goo.gl/c8n1c. I hope this helps.

• Satellite L310 - damaged USB port

  Hai, I have of me sia, I saw a model Asia Satellite L310 USB pin damaged inside.
  Which is I confirm not used to bad use by my own, & my friend recently purchase a new model problem Satellite M300 also face the same thing as mine. The service center in my country rejected my claim because they blame it on my own abuse.

  Could you help us to investigate the following case please? urgent, your help will be very appreciated.

  > have a model of Asia Satellite L310 damaged the USB pin inside. Which is I confirm not used to bad use by my own, & my friend recently purchase a new model problem Satellite M300 also faced the same as mine
  That s very strange and I cannot believe that
  I mean if the PIN to USB ports was broken on the first day of purchase, then why you didn't visit your dealer and asked the replacement of the laptop?

  However, I had 2 portable satellite in the past. Series not Asian but portable European Satellite. Now, I m using a satellite A210 and all USB ports is OK on all my series.

  You must have simply no chance cause