Module of IPS ASA 5505 Cisco ASA-SSC-AIP-5 Auto Update

Similar Questions

• Module of IPS for router Cisco 3925?

  Hello

  To be compliant HIPAA our society must have an IPS device. I was looking into it and I came across this router module (see link below). We have around 200 users behind the router and we have 2 locations with a similar setup. This module meets our requirement to have a decent IPS solution, my concerns are. It will be able to support a corporate network? Should what factors I take into account during the finalization of an IPS device.

  http://www.Cisco.com/c/en/us/products/collateral/routers/1841-integrated...

  Any idea is appreciated.

  The modules of network and all the 'old' Cisco IPS devices, modules and software are end-of-sales. Here's the announcement confirming that these specific modules.

  For a modest condition like yours, I recommend a small series of ASA 5500-X running in transparent mode with the power module of fire services running the IPS feature. It is less intrusive to your network ("bump in the wire") and only costs it for the features it offers. the exact model would be mainly depends on your current and projected throughput but for up to 50 Mbit/s with active political IPS you would be fine with the smallest model (ASA 5506-X).

  Find a Cisco partner, who has a security practice in your area. They can advise you on the details and provide a quote.

• Step how to configure ASA 5500 Series Security Services Module-10 (model: ASA-SSM-10)

  Dear support,

  I need to configure Security Services Module-10 (model: ASA-SSM-10) on my ASA 5510 firewall. Could you provide configuration step and how to connect to the module?

  Here is the information on the module

  ciscoasa (config) # sh Details of module 1
  The details of the Service module, please wait...
  ASA 5500 Series Security Services Module-10
  Model: ASA-SSM-10
  Hardware version: 1.0
  Serial number: JAF1115066U
  Firmware version: 1.0 (11) 2
  Software version: 1.0000 E1
  MAC address range: 001a.e268.5aa9 to 001a.e268.5aa9
  App name: IPS
  App status. : to the top
  App status. / / Desc:
  App version: 1.0000 E1
  Data of aircraft status: Up
  Status: to the top
  Mgmt IP addr: 133.1.9.144
  Web to MGMT ports: 443
  Mgmt TLS enabled: true

  your help is very appreciate.

  Thank you

  Best regards

  Hi Sothengse,

  Please find the samlpe on AIP SSM module configurations. You can go through this to begin with.

  http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...

  https://www.YouTube.com/watch?v=FgYU5ZXwk4g

  Concerning

  Knockaert

• IPS Appliance 7.0 Auto Update with temporary license?

  Hello

  is it possible to put a new Appliance IPS already not ver 7.0 to grab the update to automatic update of cisco.com signature using the temporary license and how, if possible,.

  Thank you

  Mike

  You should be able to get the update of signature with the temporary license, as long as the license is valid.  Please note, however

  the CCE id you enter to auto update should be able to download the software of cisco.com.

  Here are instructions on how to install the automatic update:

  http://www.Cisco.com/en/us/docs/security/IPS/7.0/Configuration/Guide/IDM/idm_sensor_management.html#wp2016040

• Cisco IPS ASA SSM - 10

  I use an IPS SSM - 10 ASA. Currently he is recording these event alerts.

  Whence the IPS keeps all the event logs? In disk space?

  Where can I see how much space I left?

  Is he got off, if the space is full?

  You don't need to delete it, its CIRCULAR and will replace itself. More information can be found here:

  http://www.Cisco.com/en/us/docs/security/IPS/6.0/Configuration/Guide/CLI/cliArch.html#wp1010399

  The command is "clear events.

  You cannot remove "individual" events Its all or nothing.

  Yes, the best way is to set the IP addresses for the false positives either edit/disable unwanted signature or use event action filters.

  Concerning

  Farrukh

• IPS modules in the ASA config for active/passive failover

  Hey guys,.

  We have two ASA in a situation of active/passive failover each with a module AIP-SSM-20 IPS.

  These modules are intended to synchronize their configs like the ASA do? Alternatively, they each have a separate entity and each need to be configured separately?

  Thanks for any help!

  Each will have their own IP address, and each must be configured separately.

  They will not communicate with each other and share no configuration.

  You will need to make sure the config is changed in one of the other.

  Monitoring station pull events from two sensors.

  The SSMs rely on the SAA for the TCP state tracking so they will work very well in a design of failover ASA.

• Client VPN Cisco ASA 5505 Cisco 1841 router

  Hello. I'm doing a connection during a cisco vpn client and a vpn on one server asa 5505 behind a 1841 router (internet adsl2 + and NAT router).

  My topology is almost as follows

  customer - tunnel - 1841 - ASA - PC

  ASA is the endpoint vpn (outside interface) device. I forward udp port 500 and 4500 on my router to the ASA and the tunnel rises. I exempt nat'ting on the asa and the router to the IP in dhcp vpn pool. I can connect to my tunnel but I can't "see" anything in the internal network. I allowed all traffic from the outside inwards buy from the ip vpn pool and I still send packets through the tunnel and I get nothing. I take a look at the statistics on the vpn client and I 2597 bytes (ping traffic) and there are no bytes. Any idea?

  Where you you logged in when you took the "crypto ipsec to show his"? If this isn't the case then try again, also this option allows IPSEC over UDP 4500 and it is disabled, enable it.

  ISAKMP nat-traversal crypto

  Just enter the command as it is, then try to connect again after activation of this option and get the same result to see the.

• which product is right for the ssl vpn: asa 5505 cisco 1841 or

  Hello

  I want to install an outside link management related so that we can ssh to our cisco devices and microsoft RDP toour servers. It's my configuration (based on what I know):

  Internet > DSL modem > ASA 5505 > management CONSOLES SWITCH > SWITCH CISCO or Windwos Server

  or

  Internet > 1841 with DSL HWIC > management CONSOLES SWITCH > SWITCH CISCO or Windwos Server

  My questions are:

  Should I go for ASA or 1841 router?

  What options is better? and ASA will do the job?

  Are there any technical support prior to purchase of products in Australia? I need technical advice on the choice of the right products, not justs eiling me products.

  Hello

  Its strongly suggested to go with ASA 5505 in the first place, it is supposed to feature for the main functionality of ssl vpn server from 1841 which has this feature to be a vpn server.

  ASDM also gives you the freedom to config box on your own based on your condition.

  regds

• Please give index on configuring vpn site to site on 881 to ASA 5505 cisco router

  Earlier my boss asked me to prepare to implement the VPN site-to site on router Cisco 881 Integrated Services to ASA 5505 router, which is now running on the side of HQ. Someone please give me a hint. I am now learning the pdf file from Cisco that mention how to configure VPN site to site between 1812 Cisco IOS router and router of the ASA 5505 using ASDM V6.1 and SDM V2.5. Cannot find the book for the Cisco 881 device.

  Someone please please suggest me something as soon as POSSIBLE.

  Thank you

  CLI version:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00807ea936.shtml

  ASDM and SDM Version:

  http://www.Cisco.com/en/us/partner/products/ps5855/products_configuration_example09186a0080a9a7a3.shtml

• ASA 5505 Cisco 7940 phone and laptop behind it

  The only problem I'm having is that when I try to use the internet port on the back of the Cisco phone, there is discount on an IP address for the Vlan voice (172.30) and not the VLan data (172.31).  Therefore, a laptop that I plug into the internet port cannot get out to the internet.  I need the laptop to get an IP address that is on the Vlan data if possible.  Thanks in advance for any help.   Here's a copy of my config.

  hostname TESTvpn
  activate the encrypted password of FsaA76FXbsPPlRSQ
  FsaA76FXbsPPlRSQ encrypted passwd
  names of
  name Corp_LAN 10.0.0.0
  name 192.168.64.0 Corp_Voice
  name 172.31.155.0 TESTvpn
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 172.31.155.1 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP address dhcp setroute
  !
  interface Vlan3
  nameif Corp_Voice
  security-level 100
  IP 172.30.155.1 255.255.255.0
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  switchport access vlan 3
  !
  passive FTP mode
  object-group network SunVoyager
  host of the object-Network 64.70.8.160
  host of the object-Network 64.70.8.242
  the Corp_Networks object-group network
  network-object Corp_LAN 255.0.0.0
  object-network Corp_Voice 255.255.255.0
  outside_access_in list extended access allow all unreachable icmp
  outside_access_in list extended access permit icmp any any echo response
  outside_access_in list extended access permit icmp any one time exceed
  inside_access_in ip TESTvpn 255.255.255.0 allowed extended access list all
  inside_access_in list extended access allowed icmp TESTvpn 255.255.255.0 everything
  Access extensive list ip 172.30.155.0 Corp_Voice_access_in allow 255.255.255.0 any
  Corp_Voice_access_in list extended access allow icmp 172.30.155.0 255.255.255.0 any
  list of VPN access deny ip TESTvpn 255.255.255.0 object-group SunVoyager
  list of VPN access extended permitted ip TESTvpn 255.255.255.0 everything
  extended VPN ip 172.30.155.0 access list allow 255.255.255.0 any
  extended vpn-data access list permit ip TESTvpn 255.255.255.0 everything
  extended voice VPN ip 172.30.155.0 access list allow 255.255.255.0 any
  all - vpn access-list extended permitted ip TESTvpn 255.255.255.0 everything
  172.30.155.0 IP Access-list extended all - vpn 255.255.255.0 allow all
  pager lines 24
  Enable logging
  exploitation forest buffer-size 10000
  monitor debug logging
  logging buffered information
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  MTU 1500 Corp_Voice
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0-list of access vpn data
  NAT (inside) 1 TESTvpn 255.255.255.0
  NAT (Corp_Voice) - access list 0 voice-vpn
  inside_access_in access to the interface inside group
  Access-group outside_access_in in interface outside
  Access-group Corp_Voice_access_in in the Corp_Voice interface
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  Enable http server
  http TESTvpn 255.255.255.0 inside
  http Corp_Voice 255.255.255.0 Corp_Voice
  http Corp_LAN 255.0.0.0 inside
  http 65.170.136.64 255.255.255.224 outside
  http 172.30.155.0 255.255.255.0 Corp_Voice
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-3des esp-md5-hmac VPN
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  outside_map 1 match address all vpn crypto card
  peer set card crypto outside_map 1 66.170.136.65
  card crypto outside_map 1 the value transform-set VPN
  outside_map interface card crypto outside
  crypto isakmp identity address
  crypto ISAKMP allow outside
  crypto ISAKMP policy 1
  preshared authentication
  3des encryption
  md5 hash
  Group 2
  lifetime 28800
  crypto ISAKMP policy 65535
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH Corp_LAN 255.0.0.0 inside
  SSH TESTvpn 255.255.255.0 inside
  SSH 65.170.136.64 255.255.255.224 outside
  SSH timeout 20
  Console timeout 0
  management-access inside
  dhcpd outside auto_config
  dhcpd option 150 ip 192.168.64.4 192.168.64.3
  !
  dhcpd address 172.31.155.10 - 172.31.155.30 inside
  dhcpd dns 10.10.10.7 10.10.10.44 interface inside
  dhcpd sun.ins area inside interface
  dhcpd allow inside
  !
  dhcpd address 172.30.155.10 - 172.30.155.30 Corp_Voice
  dhcpd dns 10.10.10.7 10.10.10.44 interface Corp_Voice
  dhcpd interface of sun.ins of the Corp_Voice domain
  enable Corp_Voice dhcpd
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  username, admin pAd1USa81YUMBD/6 password encrypted privilege 15
  tunnel-group 66.170.136.65 type ipsec-l2l
  IPSec-attributes tunnel-group 66.170.136.65
  pre-shared-key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  !
  global service-policy global_policy
  context of prompt hostname
  Cryptochecksum:fd067681ebec6394372ecb1a4d61d3a5

  Peter,

  So unlike switches the ASA does not support CDP.  As a result, there may be no communication between the ASA and the phone to distinguish the vlan data against the vlan voice.  Thus, the phone will use the vlan native to get an ip address and register.  That's what you have already configured on eth 0/7.

  When you connect a computer to the pc to the phone port, it will use the vlan native and thus be put in vlan 3 (vlan native) on port 0/7 eth.  It is expected that it will get an IP out of this range.

  So, that leaves you with two options.

  (1) disable the PC port on the phone.  This will force users to connect on ports 0/1-0/6 and be set to vlan correct.  You can disable it by going to the call Manager (Got to Device > phone, and then set "PC port" to disable).

  (2) configure nat for traffic vlan voice.  Please note that the PC connected to the phone will not be able to connect to one of the other PCs or printers on the VLAN for data (inside interface).

  NAT (Corp_Voice) 1 172.30.155.0 255.255.255.0

  I hope this helps.

  -Jay

• Need help getting ASA SSC 5 to market quickly

  Hi all

  I have tonight to understand and get this card to work and would appreciate some expert advice.

  I have an ASA 5505 and you just installed a SSC-5 card in it.  Unlike the SSM modules in the major firewalls, this not a no network card then how communicate LAN reins?

  To allow, can I do it here https://tools.cisco.com/SWIFT/Licensing/PrivateRegistrationServlet?DemoKeys=Y ?  I don't have a number of PAK and the video license says that you do not use a key PAK when licesning IPS?

  I think that if I can get these poorly sorted foundations be OK.

  Please help

  This command is for only ssc-5.

  Feisal

• New deployment with the ASA and AIP - SSM module

  Hi guys and girls,

  I think to deploy an ASA with IPS module AIP - SSM to my perimeter. I'm going to use / * Style Definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;} Cisco IPS Manager Express (IME) to monitor the IP addresses to monitor the ASA. I have no plans on deploying a device IDS.

  Question: The IME is designed to send notices to the subject of threats? What are some of the configurations in your network? (Just prick with the last question.)

  THX...

  IME is designed only for IPS monitor (whether it be IPS appliance, module AIP - SSM on ASA or other module IPS). IME is not able on the control of ASA.

  EMI can provide advice by email about events which are fires on the IPS, while the IPS itself cannot. EMI may also keep all the events triggered by the IPS, while SPI buffer is small enough, that so if you have huge demonstrations, the buffer gets replaced pretty quickly.

  Here is more information about IME, if you are interested:

  http://www.Cisco.com/en/us/products/ps9610/index.html

• Configure the module of firepower ASA IP address

  Hello

  today I tried to configure the IP address of the late ASA power module. But unfortunately I failed. The firewall is in the direction of the situation and also do have not any router on the LAN. So, I stop the management interface and configure the IP of firepower on the network server management. But unfortunately I can not ping the gateway IP address that is actually one of the interface of the firewall. It is the series x 5525 firewall. So this isn't a any interface dedicated to management of firepower. It would be nice to know where I made the mistake? I recharge and recovery of the module and I consider the State as always state of recovery. So my question is looking for there is a problem with the module itself?

  Module status

  SH module

  Model serial number of map mod
  ---- -------------------------------------------- ------------------ -----------
  0 ASA 5525 - X with SW, GE, 1 GE Mgmt, AC 8 data
  IPS unknown n/a
  cxsc unknown n/a
  SFR unknown n/a

  MAC mod Fw Sw Version Version Version Hw address range
  ---- --------------------------------- ------------ ------------ ---------------
  0 f  1.0                                                2.1(9)8      9.2(3)
  ips                                                         N/A          N/A
  cxsc                                                       N/A          N/A
  sfr                                                         N/A          N/A

  The Application name of the SSM status Version of the Application of SSM mod
  ---- ------------------------------ ---------------- --------------------------
  IPS unknown current Image number does not apply
  cxsc unknown No. current Image does not apply

  Data on the State of mod aircraft compatibility status
  ---- ------------------ --------------------- -------------
  0 to Sys does not apply
  IPS does not is not Applicable
  cxsc does not not Applicable
  SFR recover not Applicable

  Config firewall Interface

  #Interface IP-Address OK? Method State Protocol
  GigabitEthernet0/0 10.101.106.115 YES CONFIG upward upwards
  GigabitEthernet0/1 10.106.106.115 YES CONFIG upward upwards
  GigabitEthernet0/2 10.103.254.254 YES CONFIG upward upwards
  GigabitEthernet0/3 10.0.210.254 YES CONFIG upward upwards
  GigabitEthernet0/4 10.100.254.254 YES CONFIG upward upwards
  GigabitEthernet0/5 10.107.253.115 YES CONFIG upward upwards

  #interface GigabitEthernet0/1
  Speed 1000
  full duplex
  nameif Server
  security-level 70
  IP 10.106.106.115 255.255.0.0

  Fire power management configuration

  Host name: 1 Swiss francs
  Configuration Management Interface

  Configuration IPv4: static
  IP address: 10.106.251.253
  Network mask: 255.255.0.0
  Gateway: 10.106.106.115

  IPv6 configuration: Stateless autoconfiguration

  Configuration of DNS:
  Domain: XXX.local
  Search:
  XXX.local
  DNS server:
  10.101.251.2
  10.201.251.2

  Any help will be greatly appreciated.

  Thank you

  Sari

  Sari,

  Even if there is not a physical module services fire power management port, it uses Management0/0 port to connect to the module of SFR.  If you like on the same VLAN as your server VLAN on the SAA plug Management0/0 port on a switch that is sharing the network server VLAN and give the module SFR an IP address on the same subnet.

  Make sure that you remove the statement under interface Management0/0 nameif. Here is an example:

  interface Management0/0
  management only
  No nameif
  security-level 100
  no ip address

• 20 IPS ASA - SSM password reset

  Hi all

  Must reset/recover the password to get rid, for some reason, we lost the password for the IPS 20 ASA - SSM module

  Please let us know the procedure that the reset of password hw-module command does not work.

  Use the reset passwrod hw-module command, you must have ASA 7.2.2 or later version.

• Update license of IPS ASA - SSM

  Hello

  We have an ASA-SSM-20 IPS, the license has expired and we purchased a Smartnet contract for the device.

  I would like to know how to upgrade the license.

  We tried to do the ASDM, and chose the option updates to cisco.com.we got the following error.

  internal error. Unable to send the license request. -4: unable to proxy transparent tunnel. Proxy returns "HTTP/1.1 403 Forbidden.

  How to solve this problem or how to do when you use the other option, how to get the license file.

  Best regards

  It seems that your AIP-SSM20 is configured to use an http proxy to connect to the Internet. If you allow the IP address of the AIP-SSM20 management in your web proxy, it may solve your problem.

  If this isn't the issue, you can always apply a license manually. Download your license file here:

  https://Tools.Cisco.com/swift/LicensingUI/home

  and apply via the ASDM or the CLI

  -Bob