print single page hp inkjet all in one f4480

Similar Questions

• Long-term storage of inkjet all-in-one (F4480)

  Is there a good way to prepare for storing ink jet printers long-term (> 1 year) so that the jets get clogged?

  We have a F4480 deskjet all-in-one that has not been used in several months.  As far as I know it still works fine.  It has been stored in the original box & delivery packaging for 3 months.  We hope it won't be necessary for 1-2 years.  We had 2 former HP hoof to the top after a long period without use.  I said that they should be tested every month or two.  Do you need >

  This model integrates print on ink supplies heads, so in the worst case, you'll just need to replace the cartridges.  I think after a year or two ink supplies will probably dried out or clogged.   When you restore the printer to the service, you may be able to run up to three cycles of cleaning of the Toolbox.  Is there is an impression, but it is scratched or one or more colors are missing, then soak the nozzles of the cartridges down in about 1 "of very hot water for 10 minutes can recover the cartridges.

  The best plan would be to simply use the cartridges before long-term storage and then store the low or empty cartridges in the printer.

  For best results, store the printer with cartridges installed.  Be sure to turn off the printer to its power switch and wait for the cartridges to Park properly before removing the power.  Store the printer in a place cool and away from drafts, pets and other potential hazards.  Make sure that the printer is stored standing in its normal operating position.  Store the printer upside down or sideways or the end can cause problems.

• Bad or missing ink when printing or copying on HP all-in-one and color copier product families

  Click here for a description detailed steps for when colours or black are bad or missing when you print or copy on HP all-in-one and color copier product families.

  Determine if the problem is associated with cartridge

  1. the test report does not print correctly

  Check the estimated ink levels

  Check and clean the ink cartridges and the print carriage

  2. the test page prints correctly (for products only all-in-one)
  Step 1: Verify that the correct printer driver is selected in the software program
  Step 2: Restart the computer
  Step 3: Make sure that the correct printer driver is installed
  Step 4: Verify that printing in grayscale option is not selected
  Step 5: Select a color management profile
  Step 6: Determine if the problem is with the application software
  Step 7: Remove and then reinstall the all-in-one software

  Click on the laurels on the left side to help and click on accept as Solution to a solution. I work for HP.

  Best regards
  Kenneth

  I hope this helps!

• Need help printing on my C7280 Photosmart all-in-one Printer

  I use a Wireless/1100 Inspiron and have been able to print on my Photosmart C7280 all-in-one printer, but now I can too.  Help, please.

  Hello

  1. what happens when you try to print?

  2 have you made changes on the computer before this problem?

  3. do you get any error code or error message trying to print?

  I would suggest trying the following methods and check if it helps.

  Method 1:

  Run the fixit from Microsoft Fixit article and if that helps.

  Problems printing and printing errors:

  http://support.Microsoft.com/mats/printing_problems/

  Method 2:

  Try the steps in the following Microsoft article and check if it helps.

  Printer in Windows problems:

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Hope the information is useful.

• Not able to find driver Win 7 (64 bit) for printer "hp psc 2410 photosmart all-in-one. pls help

  While I insert the printer USB cable to the laptop, it runs the Windows Live Update automatically and fails in the final task, the installation of the driver. It says "hp psc 2400 series - has failed.

  Then I removed the USB cable, removed the device of "devices and printers", reboot the laptop and then tried to load the driver manually. But in the window "install print driver", I could not able to find the driver for my printer ' hp psc 2410 photosmart all-in-one ' for the operating system of Windows 7 Professional (64 bit) under the "HP" manufactured.

  Can someone help me get this printer driver to use the Win 7 (64-bit) operating system? Thank you.

  Thank you, Sean. It has not solved the problem. Instead, I got to know that this will work with the 'HP Deskjet 6980 series' pilot and his summer work after I chose that one through the configuration of the local printer.

• Unable to print on hp psc 1350 all-in-one of imac (os 10.6.8) but capable of scanning

  Unable to print on HP psc 1350 all-in-one of iMac (OS 10.6.8) but capable of scanning; also able to print other printers connected to the same computer.  The printer is connected directly via the USB port and I downloaded and installed software for printing on Mac using OS 10.6.  Shows the impression that labour is on hold whatever program originating the print job.  The State of the 'mistake' poster print job, but there is no information about error numbers or other details of the error. The correct printer is selected by default and layout is correct.  The printer has been disconnected, turned off and restarted and the computer has been restarted several times.  Able to print/scan/to 1350 PSC all-in-one of older Mac laptop (OS 10.5.8).

  Additional suggestions are sincerely appreciated.

  If you are using Snow Leopard or Lion and you have the HP software before Snow Leopard (either from a CD not marked as compatible with 10.6 or you recently upgraded to Snow Leopard or Lion and had the software HP on your Mac before you upgrade - even if you made a standard from the old software uninstaller or installed new software on top of it) , you must uninstall the software by using the "scrubber":

  Go to Applications/Hewlett Packard / click Uninstall HP
  Click on continue
  Highlight your device in the left pane
  Press and hold Ctrl + Alt + Cmd keys on the keyboard at the same time as you click on uninstall< this="" is="" the="" scrubber="" option,="" there="" is="" no="" button="" labeled="">
  There will be a pop up that asks if you are sure you want to uninstall all hp software. (At this point, if you continue, all HP printers you have installed will need to be reinstalled)
  Click on continue and let it finish

  Restart your Mac

  Now reset the printing system:

  -Sys Prefs, Print & Fax
  -Right (control) click inside the box that lists your printers and select Reset Printing System.
  WARNING - This will remove ALL your printers!
  -Select the sign + to add again. Search for the printer, select it, and wait until the button 'Add' becomes available. Until it clicks.

• pages white print Photosmart premium c310a e-all-in-one

  Bought a c310a e-all-in-one Photosmart premium in 2011-12.  He just started printing blank pages. I replaced all ink cartridges and now have the message: alignment failed. I tried the alignment printer and HP solutions without success. Is there a solution to this problem?

  Hi trainweck

  Although article I recommend you will be able to select your operating system

  If you other help I should know the what operating system are you using.

  Try this article, it may help to GO HERE

  Let me know the result, I will do my best to help you

  RobertoR

  Don't forget == ▼

• Owners of printer inkjet all-in-one Dell 962 thread (W7)

  Please follow the instructions below and then tell me what happens.

  Make sure that your computer has the latest Windows updates, especially of .net framework, necessary to run many applications and the latest Java.

  Unplug your printer.

  Download and run this patch to completely remove the printer from your computer. Run the fix, a MUST on Vista machines, until it prompts you to restart your computer.

  If you use Windows 7 also try... Driver Manual printer removal

  Restart your computer.

  Download the correct drivers.

  XP drivers

  Vista 32-bit drivers

  All other drivers

  Vista 64-bit drivers

  Install the appropriate drivers. You will be asked when connect you your printer (power on)

  To install the drivers, sometimes the file decompresses and does nothing. You must find the setup.exe file, right-click on it, then on the left click on run as administrator *.

  If you use Windows 7, use the Vista drivers in compatibility mode.

  Right click on the file setup.exe, on the left, click Properties, compatibility of the left click. Replace the Vista compatibility (try Vista SP2). Then, install the appropriate drivers. You will be asked when connect (printer)

  To install the drivers, sometimes the file decompresses and does nothing. You must find the setup.exe file, right-click on it, then on the left click on run as administrator *.

  In the digitization, if you have the disc that came with the printer, and then insert the floppy disk to the printer and keep it from running. Go to my computer and double-click it. Locate the drive that contains the disk Dell inside. Right-click on it, left click Explore. Find the folder of the OCR. In the OCR folder, there is a folder of Abbyy. Right click on setup.exe, which is located in the folder Abbyy and left, click Run as administrator. This will install the OCR program.

  Scanning

  Scan using the USB connection, open the Dell all-in-one Center, click on the scan and copy and scan from there.

  Scan wireless, use the buttons to scan on the printer.

  Rick

  Rick,

  Thank you much for the help. I took your advice and installed the Vista SP2 drivers in compatibility mode, and when my laptop is connected to the printer via a USB cable, I can print.  Now, here's the best... Later, I decided to have the printer put in place for the wireless.

  I tried to add a Dell network port, and then pass.  Did not work.  I tried also to add another printer by pointing to a shared printer on an XP computer.  I noticed one thing, it is that when the Dell printer software installed and prompted me to plug the printer into my USB port, it appeared that Windows snuck into another driver.  I saw a message saying that the printer was ready before the Dell software were made.  I also noticed that when I tried to create a new Dell printer two print drivers were available.

  In any case, I followed your instructions to uninstall everything (ran program of uninstalling the Dell software, rebooted, ran the patch to clean, restarted), then ran the Dell program configuration of the software (in compatibility mode Vista x 64 SP 2) and chose an installation over the network instead of local installation. He saw the Dell printer on USB wireless adapter and installed fine.  Now, everything seems to work wireless.

  I guess my point of view for writing is to warn that when you plug the USB cable during installation of Dell, it seems that Windows 7 is going to sneak in another pilot.  I also advise to install over the network if you want to try to use it wireless, rather than starting with the local USB installation and hope to switch to a network port later.  Thanks again for your message.

• scanning documents with multiple pages on 2542 all-in-one

  Therer is a way to scan multiple pages into a single pdf file on an HP 2542 all-in-one printer/scanner

  Hello

  Since your computer open the HP Deskjet 2540 software anc lcik on scan a document or photo.

  Select PDF and make sure the option Show Scan preview is checked.

  Ensure that the scanning resolution is 300 dpi or lower.

  Click Scan in the scan preview, click the button add page, under the overview of digitization, once you have finished click on save or finish to compete with the analytical work.

  Shlomi

• print jam transport Photosmart 2575 All In One

  I have a HP Photosmart 2575 all-in-one.  I get an error message that the transport is stuck, but when I opened the door there doesn't seem to be any jams.  I don't see anything in the way, and I can move the cart.

  I am using Windows XP Pro.

  Any suggestions are welcome.  I couldn't find the repair shops for an inkjet.

  Hello whit66,

  Thank you for the information. At this point, printing a page and still get the error for carriage Jam message. I've included a link to another HP Forum post that you can try, "jam of transport will not be deleted. Please follow the steps described by Bob_Headrick.

  For half a page of printing, it starts printing the top of the page and then stops? You have to pull the rest of the page printing? Or it sounds like it is printing the rest of the page, but comes out blank?

  Impatience on your part.

• Printer ink system failure message all-in-one HP 6180

  I can't print because of the error message following on my all-in-one HP 6180 printer screen:

  Ink system failure. Refer to the documentation of the printer Oxc18a0201. I followed all the recommendations on documentation of the printer, such as: installation later HP updates, turn off the printer and remove the power cord, remove all the ink cartridges and then putting back in when prompted. Also, I rebooted my computer. None of these recommendations have worked. I need help! Thank you.

  Hello Kah524,

  I met your questions and we have a solution for this and you can try it, but that would apply only on starting with '0xC18A' and not '0xc19a error codes.

  Try the following steps for Photosmart C7280:

  A. - Press and hold the "*" key.

  B. - Press the "#" and release both buttons.

  Display should say "enter special key Combo".

  C. - Press and release in sequence the buttons '1', '2' and '3 '.

  Display should say "Support" and display the FW rev (something like R0631R)

  Press and release the right arrow button until the display shows "Menu of the System Configuration'.

  Press and release the OK"" button.

  Display should say "hardware failure status. If it isn't there already, arrow above for "Hardware failure status"

  Press and release the OK"" button.

  Display should say "hardware failure status: clear." Press OK to erase.

  Press and release the OK"" button. Message becomes "hardware failure (breakdowns) resolved state. Press Cancel to continue.

  Press and release the "CANCEL" button as many times as necessary, so that, either the "Welcome to Photosmart Express" screen appears, or, the 'ink system failure' is displayed. DON'T TRY TO PRINT AT THIS STAGE.

  Using the power button, turn the power off and unplug the power cable from the back of the printer output and the wall.

  Wait 30 seconds for the power to get discharged and then plug the power cable into the wall outlet first, and then to the back of the printer

  Switch on the device. The printer may display message "USE POWER BUTTON CLOSING the PRINTER" followed by "Press OK TO CONTINUE". Press OK.

  If the printer has already initialized, then go to the next step. If this isn't the case, the printer will start the "ONE TIME INK initialization PROCESS". Allow this process to do and not to interrupt. Once the initialization is completed, the printer print a Diagnostic page.

  To check, features of the printer print a PAGE of TEST car. If SELF TEST prints, then printer is ready for use or installation of the software.

  If the error is still there, or reoccurs replace the unit.

  --------------------------------------------------​---

  0XC19a error messages, the printer can be retrieved.

  Good luck and if that fixes the problem please click on Bravo...

  ---------------------------------

  Although I am an employee of HP, I speak for me.

• 1209: loading paper HP inkjet all-in-one

  I need to know how to load paper in my all-in-one, inkjet 1209.  It was my husbands printer.  He died so I can't ask him.  I tried to find the answer online, but I can't find anything.  I hope someone can help me.

  My condolences on your loss.

  The document here can help to load the paper for your HP PSC 1209.

• . HP Smart printing fails to include images - all-in-one printer, HP Photosmart 3210

  With the help of HP Smart printing on all-in-one printer, HP Photosmart 3210. Smart photo has disappeared from my computer and now reappeared. Now the images are not yet an option to include on the printed page. They do not appear.  Has anyone else had a problem with Photo Smart?

  What operating system do you use?

  What did you do to make them reappear, or just is it?

  Have you noticed updates to HP or Windows until the printer is missing? What happened before he reappeared?

• Can copy and scan but not print with my hp deskjet all-in-one 1515

  Hello

  Pls help! I can't print. I can scan and photocopy with my hp deskjet printer 1515 all-in-in-one, but I can't print. I tried to print with my computer laptop windows 7 and was able to print but I can't print using my regular laptop, which is a laptop HP 650 which uses windows 8.1. When I send a document to print is says it is printing and shows in the print queue and then disappears. What can I do? He has not even print a test page but it printed a page of information and the alignment of catrige page.

  Hello

  Please, try the following steps and let me know if that can help you:

  1. In the Control Panel, select uninstall a program and uninstall the driver software base HP Deskjet Ink Advantage publicly traded 1515.
  2. Click the R keys on your keyboard and the Windows Logo appears in the Run dialog box.
  3. Spool type and click OK.
  4. Open the Drivers folder, and then select the x 64 folder if you have a 64-bit OS or the w32x86 if you have a 32 bit OS
     Note: visit http://whatsmyos.com/ to find your type of operating system if necessary.
  5. Open the 3 folder, locate the HPBXPSRENDER. DLL file and rename it to HPBXPSRENDER. OLD
  6. Reinstall the latest version of the HP software:
     http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=Al-117537-4&cc=us&DLC=en&LC=en&OS=4158&product=5385208&sw_lang=

  Shlomi

• Print single page...

  Hi people,

  I have a Photosmart Plus B210a under Windows 7 x 64.

  Is there a way to resize or force a print to fit on a single page? Emails are my current problem, with just a few lines in general working on page 2. I tried using gmail, Yahoo and gmx but can't find a way. In addition, with gmx email all the graphics may not print completely, although they appear on the preview before printing.

  Any help and advice welcome! Thank you.

  I tried seraching for a solution to your problem, maybe this will help you:

  http://www.HP.com/global/us/en/consumer/digital_photography/free/software/smart-Web-printing.html

  This is a free tool that you can download.

  "The internet has become easy to print.
  
  With a simple plug-in for browser, Clip & quickly Select or Select & Print web pages just the way you want and eliminate all this waste of ink and paper. Download HP Smart Web Printing and get the favorable impression today!
  
  For Windows XP, Windows Vista® and Windows 7
  For versions of Internet Explorer 6, 7 and 8