Similar Questions

• Initial setup for the module of firepower, where start

  Hello world

  Ask your help once again, first of all, I've read a ton of guide as to the initial configuration, i.e., initiate the module fire power so that covered.

  Recently, one of our clients bought a new ASA with services of firepower, all is well and good, until I saw that on the nomenclature, it has SF - FP5.3.1 - K9.

  As far as I know, admins are who will begin the device, for example, through to bootstrap and OUR system software desired.

  My question is, what I really have to go v5.3.1? or can I just jump to 5.4? for example, to download the software "bootstrap" of 5.4 and 5.4 sys
  Note This is a new ASA fresh-from-the-box-with-the-smell-of-cisco ^_^

  Hi LJ,.

  In this case you can directly jump to 5.4 because she didn't have any configuration.

  Kind regards

  Aditya

  Please evaluate the useful messages.

• BIND THE SINGLE TUNNEL ON ASA IP ADDRESS

  Hi all

  BACKGROUND

  We have a VPN site-to put in place between two ASAs by using IPSEC.

  PROBLEM

  We will refer to this configuration as a site A and site B. The site has, we have an obligation to ensure that all traffic from a single host goes through the VPN tunnel while all the other guests to site A have local access to the internet and do not cross the L2L tunnel. We study the best solution for this, including the possibilities of VLANS, static NATs and ACL. Also on the client device, we'll need to bind a MAC address to ensure the same local IP address is returned every time via DHCP, although if the client device sits in its own VIRTUAL local network for example then binding MAC address is not required. It is not possible to configure a static IP address on the host device.

  Does anyone have recommendations as to how best to configure this requirement.

  Thank you

  You are right that the ASA, for now, does not support the DHCP reservations. If your only option to get what you want to work is to place the customer in a VLAN separated where you can assign a distinct scope (as you mentioned)

  --

  Please note all useful posts

• Access violation at address 59 * 963 in the module 'SMM.dll '. Read address 00000004

  Hello

  I get this error when you try to start the Migration of data from Samsung.

  I tried to start in safe mode, the same error.

  Also run a sfc/scannow found no errors.

  I also tried to run the program as an administrator, no luck.

  The address change slightly (*) 59 * 963 every time.

  What should I do?

  

  EDIT: Change address

  I found the solution.

  WARNING: This isn't a very good, and it could cause data loss. Use it at your own risk.

  Just go to the folder were Samsung migrating data stored and cut the SSM.dll.

  Then, run the program and paste them again.
  Successfully, I cloned my drive and found no errors with chkdsk or sfc/scannow.

  Works so far :-)

  Still don't know how to uninstall the program, but that's another issue...

• BitLocker, configure the module TPM after encryption.

  Hey,.

  I encrypted my hard drives in my pc with BitLocker, but I have now ordered a TPM chip I have planed for use with BitLocker.

  I think I know how to upgrade the system drive (c) to the specification of the TPM module, but I don't know how to upgrade other readers 'internal' encrypted to TPM.

  https://mrhorn.com/WP/posts/BitLocker-with-TPM-pin-USB-StartupKey/

  On this site, I discovered how to change the secure TPM system drive.

  It feels a little awkward and sad decipher and then re-encrypt with TPM to do together with the TPM module. (X takes hours to encrypt a disk of 1 TB)

  This site I found later and I hope that it would work to "fix" the other internal drives to the TPM + Pin specifications without decryption...

  http://mikebeach.org/2011/12/08/how-to-enable-BitLocker-tpmpin-after-encrypting-hard-drive/

  I thought that theses commands should work then

  manage-bde-protectors-add c: - TPMAndPIN

  And when I put the (c :)) Windows Media Player to TPM + Pin + StartupKey, '123456789' represent the pin code.

  manage-bde -protectors -add C: -TPMandPINandStartupKey -tp 123456789 -tsk E:
  

  manage-bde -protectors -add C: -RecoveryKey F:Thanks for reading, and i hope i will get a qualified answer in not to long time....Cheers!
  

  Hello

  I suggest you to send your request in the TechNet Forums to improve assistance in this regard. They are experts in your field of investigation and would be in a better position to answer your concerns.

  http://social.technet.Microsoft.com/forums/en-us/home?category=w8itpro&filter=AllTypes&sort=lastpostdesc

  It will be useful.

• CISCO ASA 5515 WITH THE VERSION OF FIREPOWER

  ASA 5515 service with the power of fire. Can be managed with ASDM firepower. ?

  Anyone suggests Versions for firepower, ASDM, ASA?

  Kindly help

  You will find it useful to install the Module of firepower on ASA for the management of the premises:

  http://www.Cisco.com/c/en/us/TD/docs/security/ASA/Quick_Start/SFR/firepo...

  Thank you

  Guillaume

  Rate if this can help!

• Can the interface of management firepower & ASA-Inside interface be on separate subnet?

  HI -.

  Need a few more details, please.

  I have a requirment needed to put the power of fire management interface and the interface of the ASA-Inside on different subnets, supports?

  From what I've read so far, most of the document suggests to put two interfaces on the same subnet, is there a reason to do so?

  I may be wrong but I think that fire use management interface to communicate with FireSight for control and comamnd traffic, data traffic real plan always flows from ASA-outside to inside and vice versa, both there are connectivity ip between FireSight and firepower, it should be ok, right? or am I totally wrong, that they must be on the same subnet?

  ASA5515-x with the firepower 5.3.1

  Thanks in advance for your help.

  Separate subnets are fine.

  As you have seen correctly - the module of firepower has need to contact FireSIGHT Management Center (IP-wise).

  This path is completely independent of the plan through the ASA data path. The ASA redirects the traffic via the service strategy for the module of firepower entirely internally to the unit.

• Firepower ASA Web Proxy services

  I was wondering is it possible to configure the web proxy http and https on the SAA with services of firepower?

  Kind regards

  Caesar

  He inspects inline http and not as a proxy server.

  We have limited how much we can do with https because from the version current (5,4) we cannot SSL decryption on the modules of firepower.

  If you ask about the firepower modules itself, it is adjustable to use a proxy server for its external communication.

• I have hp elitebook 8440p, I inserted the sim card, but I'm not able to see where to configure the sim card

  Hi I have a hp elitebook 8440p but I did not; KWN how to use sim card option, I inserted the sim card, but now I can't see wher to configure the sim card or use, cos I m unable to see any option, so please help me

  Hello

  The HP EliteBook User guide contains information on what is required to configure the module top mobile broadband in your mobile workstation. Go to the HP Web site for more information about the configuration and activation of the SIM card.

• Defining the name of the module in the program of the OIC

  Hello
  
  I was struggling with defining the name of the module in my OIC program. Here's the code in which
  I create the environment, connect, try to set the module attribute, wait for the Enter key and clean
  and exit after completing the Enter key.
  
  I can say, I called OCISetAttr as the documentation says I should, and none of my return values
  indicate a problem. Yet, when I v $session, I get what I assume is the default value of the module
  and no value, I put in the code ("moduletest").
  
  The physical file name programs is oci101.exe. It also connects to the Oracle instance as a named user
  oci101. I check v$ session with this query:
  Select the user name, the module from v$ session where the username is not null;
  
  And the output is as follows:
  
  USER MODULE NAME
  ------------------------------ ------------------------------------------------
  OCI101 oci101.exe
  SQL SYSTEM * more
  
  I see a column value 'moduletest' for the OCI101 user MODULE.
  
  Don't know what I'm missing. Any ideas? Here is the code:
  
  Code BÉGIN:
  
  OCIEnv * envhp;
  UB2 charset_id = 0;
  UB2 ncharset_id = 0;
  UB4 mode = OCI_DEFAULT;
  
  sword env_rc = OCIEnvNlsCreate () const
  & envhp, mode,
  (void *) 0, / / context for the allocation of memory to custom user defined
  (void *) (*) (void *, size_t) 0, / / malloc user defined
  (void * (*) (void *, void *, size_t)) 0, / / realloc user defined
  (void (*) (void *, void *)) 0, / / / / free user defined
  (size_t) 0, / / off user memory
  (void *) 0,.
  charset_id, ncharset_id
  );
  
  OCIError * errhp;
  sword err_rc = OCIHandleAlloc () const
  (dvoid *) envhp, (dvoid *) & errhp,.
  OCI_HTYPE_ERROR (size_t) 0, (dvoid *) 0
  );
  checkerr (err_rc, errhp);
  
  OCISvcCtx * svchp = 0;
  sword l2rc = OCILogon2 () const
  envhp, errhp, & svchp,
  (const OraText *) zusername, (ub4) strlen (zusername).
  (const OraText *) zpassword, (ub4) strlen (zpassword).
  (const OraText *) zdatabase, (ub4) strlen (zdatabase).
  mode
  );
  checkerr (l2rc, errhp);
  
  Define the attrbute module
  Extract the session descriptor in sessionhp.
  
  OCISession * sessionhp = 0;
  UB4 sh_size = 0;
  sword oci_attr_get_status = OCIAttrGet (svchp,
  OCI_HTYPE_SVCCTX,
  & sessionhp,
  & sh_size,
  OCI_ATTR_SESSION,
  errhp);
  checkerr (oci_attr_get_status, errhp);
  
  Configure the module
  sword oas_rc = OCIAttrSet (sessionhp, OCI_HTYPE_SESSION,(void *) 'moduletest',
  strlen ("moduletest"), OCI_ATTR_MODULE, errhp);
  
  checkerr (oas_rc, errhp);
  
  GetChar ();
  Cleaning:
  If (svchp) {/ / 0 when already disconnected}
  OCISvcCtx * const tmp_svchp = svchp.
  svchp = 0; reset the svchp error or not
  const sword lorc = OCILogoff (tmp_svchp, errhp);
  checkerr (lorc, errhp);
  }
  
  sword const rc = OCIHandleFree (envhp, OCI_HTYPE_ENV);
  End of the Code.
  
  Thanks for any help...
  
  Karl

  Hi Karl,

  I'm certainly not an expert of BEAK, but after you set the module attribute, the value is updated when the next execution of the statement in my experience. There may be other ways in which this can happen, but I have not seen such cases.

  Here is a short example:

  #include 
  #include 
  #include 
  #include 
  
  int main(int argc, char *argv[]) {
    OCIEnv      *envhp = NULL;  /* OCI Environment handle     */
    OCIError    *errhp = NULL;  /* OCI Error handle           */
    OCISvcCtx   *svchp = NULL;  /* OCI Service Context handle */
    OCISession  *usrhp = NULL;  /* OCI User Session handle    */
  
    OCIStmt     *stmtp = NULL;  /* OCI Statement handle       */
  
    /* the statement to execute   */
    /* this is purely for example */
    oratext *sqlstmt = "begin null; end;";
  
    /* connection information */
    oratext *username = "scott";
    oratext *password = "tiger";
    oratext *database = "orademo";
  
    /* used to hold the results of each OCI call */
    sword result = 0;
  
    /* Initialize and create a default environment */
    result = OCIEnvCreate(&envhp,
                          OCI_DEFAULT,
                          (dvoid *) 0,
                          0,
                          0,
                          0,
                          (size_t) 0,
                          (dvoid **) 0);
  
    /* allocate an error handle */
    result = OCIHandleAlloc((dvoid *) envhp,
                            (dvoid **) &errhp,
                            OCI_HTYPE_ERROR,
                            0,
                            (dvoid **) 0);
  
    /* create connection */
    result = OCILogon2(envhp,
                       errhp,
                       &svchp,
                       username,
                       (ub4) strlen(username),
                       password,
                       (ub4) strlen(password),
                       database,
                       (ub4) strlen(database),
                       OCI_DEFAULT);
  
    /* get the user session handle */
    result = OCIAttrGet(svchp,
                        OCI_HTYPE_SVCCTX,
                        (void *) &usrhp,
                        NULL,
                        OCI_ATTR_SESSION,
                        errhp);
  
    /* set the module attribute */
    result = OCIAttrSet(usrhp,
                        OCI_HTYPE_SESSION,
                        (void *) "My Module",
                        (ub4) strlen("My Module"),
                        OCI_ATTR_MODULE,
                        errhp);
  
    /* allocate the statement handle */
    result = OCIHandleAlloc((dvoid *) envhp,
                            (dvoid **) &stmtp,
                            OCI_HTYPE_STMT,
                            0,
                            (dvoid **) 0);
  
    /* prepare the statement for execution */
    result = OCIStmtPrepare(stmtp,
                            errhp,
                            sqlstmt,
                            (ub4) strlen((char *) sqlstmt),
                            OCI_NTV_SYNTAX,
                            OCI_DEFAULT);
  
    /* execute the statement - after execution the */
    /* MODULE value should be updated in v$session */
    result = OCIStmtExecute(svchp,
                            stmtp,
                            errhp,
                            (ub4) 1,
                            (ub4) 0,
                            (CONST OCISnapshot *) NULL,
                            (OCISnapshot *) NULL,
                            OCI_DEFAULT);
  
    /* print a simple prompt    */
    /* view session in SQL*Plus */
    printf("program paused, ENTER to continue...");
    getchar();
  
    /* disconnect from the server */
    result = OCILogoff(svchp,
                       errhp);
  
    /* deallocate the environment handle */
    /* OCI will deallocate child handles */
    result = OCIHandleFree((void *) envhp,
                           OCI_HTYPE_ENV);
  
    return OCI_SUCCESS;
  }
  

  When the program is paused I see this in SQL * more in my test:

  SQL> select sid, username, program, module from v$session where username = 'SCOTT';
  
         SID USERNAME         PROGRAM                          MODULE
  ---------- ---------------- -------------------------------- --------------------------------
         136 SCOTT            OCIModuleTest.exe                My Module
  

  Maybe it's a little help.

  Kind regards

  Mark

  Published by: Mark Williams on December 22, 2008 11:06

  Put a little sample.

• Step how to configure ASA 5500 Series Security Services Module-10 (model: ASA-SSM-10)

  Dear support,

  I need to configure Security Services Module-10 (model: ASA-SSM-10) on my ASA 5510 firewall. Could you provide configuration step and how to connect to the module?

  Here is the information on the module

  ciscoasa (config) # sh Details of module 1
  The details of the Service module, please wait...
  ASA 5500 Series Security Services Module-10
  Model: ASA-SSM-10
  Hardware version: 1.0
  Serial number: JAF1115066U
  Firmware version: 1.0 (11) 2
  Software version: 1.0000 E1
  MAC address range: 001a.e268.5aa9 to 001a.e268.5aa9
  App name: IPS
  App status. : to the top
  App status. / / Desc:
  App version: 1.0000 E1
  Data of aircraft status: Up
  Status: to the top
  Mgmt IP addr: 133.1.9.144
  Web to MGMT ports: 443
  Mgmt TLS enabled: true

  your help is very appreciate.

  Thank you

  Best regards

  Hi Sothengse,

  Please find the samlpe on AIP SSM module configurations. You can go through this to begin with.

  http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...

  https://www.YouTube.com/watch?v=FgYU5ZXwk4g

  Concerning

  Knockaert

• Registration Module software firepower to the CMF. Need a key "Reg"?

  Community,.

  I'm extremely new to the product of the power of fire and was assigned to the online in my new job. We have the power module of heat load on the x 5545 and CME loaded as a virtual machine on a server. IM at the stage now where Im trying to record the firepower to the CSP module using the Configure Manager add x.x.x.x   command in the CLI of Module of firepower. My question is, where can I get the registration key of? All the documentation says it's a key to register the module in the CSP. Unfortunately this deployment was already partially in place before I was here so I don't know what this alphanumeric key is or where to find it. Any ideas?

  Thank you!

  Hello Craddockc,

  You can use any combination of alphanumeric characters as key such as abc123.  Make sure that you add the same key when registering of firepower on CMF too.

  Note and mark the messages useful.

  Concerning

  Jetsy

• Collage error: runtime error. Error: access violation, address of the error: 0000 P 280, the Module name: GFSData.DLL

  Hello to all on the forum,

  I am running DIAdem 2015 (15.0.0f6005) on a Windows 7 Pro SP1 i3 4 GB RAM machine.

  I want to evaluate a test. Data are expressed as 25 .txt files. I need to plot, one of the values on the whole test time. I tried to combine the data from all 25 in one file .tdm .txt files. I came far enough until I met my problem. After gathering around 15 .txt files in a .tdm, tiara doesn't let me continue. It gives this error message (in German, I'll translate as good as possible):

  "When executing command 'DataBlClpPaste('1-52',1859122,0)' a rumtime error has occurred.

  Error: ACCESS VIOLATION

  Address of the error: 0000 P 280

  "Name of the module: FGSData.DLL.

  I will describe my procedure in which this happened:

  -Open the .txt with plugin I had created the first import

  -Ribbon with two windows view channel: have the target in a secondary window group, drag the newly imported from .txt in the other channels

  -In the secondary window with new data, select the lines I want to add to the data target group by clicking on the first line, then scroll to the last row and shift-select that. CTRL + c to copy the data

  -In the target group, click the first empty line, and then ctrl + v to paste data here

  After the last step, instead of pasting the new data in the target dataset, the above message error. I can't do anything, but click on 'ok '. After ok, the program window will not respond to any click except for switching between Navigator / View / analysis /... I have to close DIAdem, where I can always select "close and save", that works too.

  I could go a few times after reopening DIAdem, but finally, which stopped working. It now gives me the error message whenever I try to do this routine. The .tdm file is 21Mo now, the .tdx is 1.1 GB.

  I appreciate any help on this, I really would prefer combining data using DIAdem on trying to copy and paste around 1 GB of data .txt into one giant .txt file. It takes very long to not even open a .txt of 50 MB file, I fear this would be a messy process.

  Best regards

  Simon

  If you are using DIAdem 2015, there is a new entry in context menu where you can select Add.

  Maybe it helps.

  The help of DIAdem 2015:

  Adding data

  
  

  Adding data to merge similar series ratings data in order to deal with them. In the process, DIAdem adds the data to load for existing channels with the same name in the data portal instead of storing data in new channels. Perform the following steps to add the external data area data channels in the data portal:

  1. Open the NAVIGATOR tiara.

  
  

  2. Select remove internal data to delete the data in the data portal.

  
  

  3. Find the Demo1.tdm file in the file browser.

  
  

  4. Drag and drop the file in the data portal.

  
  

  5. Select the Demo2.tdm file in the file browser.

  
  

  6. Open the context menu of the file and select Add data.

  
  

  Tiara adds the data in channels that have the same name in the data portal. In the properties of the Data Portal window, you can see that the number of values in the channels has doubled.

• Can someone give an example of how to configure the subnet mask associated with the network and host of an IP address part?

  Can someone give an example of how to configure the subnet mask associated with the network and host of an IP address part?

  Hi stuckfree,

  The question you posted would be more appropriate on the TechNet Forums. I would recommend posting your request here.

  http://social.technet.Microsoft.com/forums/en/itproxpsp/threads

• Unable to configure the address IP 8184 PXI

  Hello

  I can not configure the IP address of a PXI 1031 with a controller 8184. I followed all the steps in the manuals to help but after that assignment of an IP address, when I restart the controller the following message is displayed:

  mounting: mounting/dev/hda1 on/home/ftp/c failed: invalid argument

  Enter safe mode

  The 0.0.0.0 IP address

  The hard drive has two WinXP and LabView real-time installed, but the second switch of hardware on the 8184 is enabled, then the controller boots with LabView RT in Mode without failure (as indicated on page 2-13 of the PXI-8184 user manual)

  Does anyone know how to fix this?

  Thanks in advance

  Hello Casey,.

  Apparently, the issue is resolved. I formatted the hard drive of the PXI-8184 (with the FAT file format) and after reboot, I was able to 'paste' an IP address. Subsequently, I installed all the software of motion, that I need and in real time of NEITHER.

  Yes, PXI was ordered with dual boot. It is amazing that NEITHER offer the dual boot with a file system that does not allow for dual boot! Moreover, as I could see, there is not a single line on the manual in the PXI-8184 allerting or help files to this problem! This should be corrected... I spent a week trying to fix this! If it wasn't for your help, I always don't seek an answer.

  Thank you once again,

  João