MP3 and the router... What to do next?

Similar Questions

• I am unable to connect to my router wirelessly to parents. I tried to reset the modem and the router and it still does not work.

  Presented labtop parents and can connect via ethernet, but still cannot connect to the wireless router. Ive rebooted both the modem and the router and ive also unplugged the power source. Help, please...

  original title: unable to connect to the wireless router?

  Hi Brandon,.

  What operating system do you use? (Windows 7, Vista, XP?)
  You receive any type of error message when you try to connect?
  What exactly happens when you try to connect?
  You receive an internet connection when you connect with an Ethernet cable?
  There are a few good troubleshooting in this thread. I suggest to look to see if it helps at all:
  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/unable-to-connect-to-a-wireless-network-Windows-7/734ecdef-99fb-4862-b63a-04cfa448cc06

• Internet connection is unreliable - when a wireless computer connects to the network, all other stands and the router needs to be reset

  I have a home wireless network with a new router Belkin (no separate modem). There are four laptop computers in our House, which connect to the wireless network. One of them is Windows 7, both Vista and the other is XP.

  Sometimes the internet works perfectly well and all four laptop computers are able to connect simultaneously. But more often... when a new laptop is on and attempts to connect, all current laptops get kicked out of the network all together and are unable to reconnect. The network broadcasts always and appears in the list of available networks, but we are unable to connect.

  Other times, if my roommate is very well on the internet and I turn on my laptop, I can't see even the network, despite the fact that it is to use! If I turn the router off and on again (sometimes we do this several times) it works OK again.

  Sometimes this happens several times a day, other times we go days without having to reset. The problems are more frequent when the old Vista laptop is used which is what made me think it may be related to computers (or their settings) rather than the router.

  Thank you

  Alex

  You may need to check every laptop and the router, to be sure.

  Go to the website of the manufacturer of your Belkin router > make sure you have the latest Firmware for it.

  Go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > look for it last network adapters Vista drivers > download/install the.

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-adapter-problems

  Troubleshoot network adapter problems to Microsoft link above.

  Try without commitment TCP/IPv6:

  If you still have internet connection probs, one thing to try is the separation of the TCP/IPv6 (which is done by going to network connection > right click > properties > it uncheck > OK.)

  http://digitalmediaphile.WordPress.com/IPv6-how-to-unbind-from-a-NIC-in-Windows-Vista/

  See you soon.

  Mick Murphy - Microsoft partner

• I got a new modem and the router and now I can't print wireless.

  I have a Photosmart 8450 printer.  My operating system is Windows7.  I tried to follow the Scan doctor, but I guess I'm not tech savy enough to understand.  It worked fine before the new modem and the router.  She is 'offline' and I can't understand how to put line.  Thanks for any help and easy enough for me to follow.

  Hello raedene715.

  Thanks for the transcript, it was useful.

  Please, check the network cables and connections (side of the printer and router). If possible, try a different network cable.

  See you soon!

• Can not connect with the Adobe server to upgrade the PS. Tried with fiervall and the router and called my provider. She is also only CC there are problems!

  Can not connect with the Adobe server to upgrade the PS. Tried with fiervall and the router and called my provider. She is also only CC there are problems!

  Check your hosts file.

  help for that and other adobe.com sure common connection problems read, http://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html

• Function to change the mp3 and the framework (video)

  I am currently working on a music website that has a custom built-in mp3 player, where the script action calls for an external xml. It works beautifully. It's all about a frame... in the back of the radio is edited video that I handled in final cut. I have buttons next and pre who call the XML. What I'm trying to do, is change the video when the song changes. I'm not sure if I call a fuction to the next section of the button + or - 1 or if I can call the video to xml. I'm a graphic designer learning code and do not know how to approach this problem. This site is my senior project... Help, please!

  the question is a matter of design.  How do you want your app to work?

  You app starts with an mp3 player and a f4v.   What happens when one who has the shortest duration ends the play?

  your current coding, you would advance to the next mp3 and f4v next which means one or other of the previous mp3/f4v will be stopped before the end.  is that what you want?

• I have a Wireless N card and the router, but only to connect to wireless-G speeds

  I just got a new HP DV7T with a N (with bluetooth) wireless card: Intel Centrino Advanced - N 6200 AGN

  I use a Netgear wireless router (WNDR3700) double radio.

  My wife's cell phone can connect to the router with a N Wireless card at a speed of 170 Mbps.

  My laptop can connect only to 54 Mbps. I checked that I am connected to radio N of my router (the radio of G/B/A has a separate connection).

  I found a useful post here:

  http://h30434.www3.HP.com/T5/wireless-Internet-and-home/wireless-does-not-seem-to-connect-at-802-11n...

  I followed the advice of responses and checked all the settings of the router (but the success of my wife to connect at speeds N essentially rules on the router) and checked the settings of the adapter to make sure it helped N.

  I wonder what it is that I'm missing. Any suggestions would be greatly appreciated.

  Thank you.

  I was able to determine the problem after extensive web searches.

  I was using the WPA-TKIP authentication which, in some cases, prevents the speed N Wireless.

  Once I changed WPA2-AES authentication radio N I got immediately 300Mps speeds and it varies between 240-300Mbps now.

  I hope this will help others with the same question!

• Routing problem between the VPN Client and the router's Ethernet device

  Hello

  I have a Cisco 1721 in a test environment.

  A net 172.16.0.0/19 simulates the Internet and a net 192.168.1.0/24 simulates the net, the VPN tunnel must go to (intranet).

  The net 172.16.0.0 depends on the router 0 FastEthernet, Intranet (VPN) hangs on Ethernet 0.

  The configuration was inspired form the sample Configuration

  "Configuring the Client VPN Cisco 3.x for Windows to IOS using Local extended authentication"

  and the output of the ConfigMaker configuration.

  Authentication and logon works. Client receives an IP address from the pool. But there's a routing problem

  side of routers. Ping client-side - do not work (the VPN client statistics that count encrypt them packets, but not to decrypt).

  Ping the router works too, but decrypt and encrypt customer statistics in VPN packets count progressive

  (customer has a correct route and return ICMP packets to the router).

  The question now is:

  How to route packets between the Tunnel and an Ethernet device (Ethernet 0)?

  conf of the router is attached - hope that's not too...

  Thanks & cordially

  Thomas Schmidt

  -.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.- snipp .-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.

  !

  version 12.2

  horodateurs service debug uptime

  Log service timestamps uptime

  encryption password service

  !

  !

  host name * moderator edit *.

  !

  enable secret 5 * moderator edit *.

  !

  !

  AAA new-model

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  !

  ! only for the test...

  !

  username cisco password 0 * moderator edit *.

  !

  IP subnet zero

  !

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  crypto ISAKMP policy 3

  3des encryption

  preshared authentication

  Group 2

  !

  ISAKMP crypto client configuration group 3000client

  key cisco123

  pool ippool

  !

  ! We do not want to divide the tunnel

  ! ACL 108

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  interface Ethernet0

  no downtime

  Description connected to VPN

  IP 192.168.1.1 255.255.255.0

  full-duplex

  IP access-group 101 in

  IP access-group 101 out

  KeepAlive 10

  No cdp enable

  !

  interface Ethernet1

  no downtime

  address 192.168.3.1 IP 255.255.255.0

  IP access-group 101 in

  IP access-group 101 out

  full-duplex

  KeepAlive 10

  No cdp enable

  !

  interface FastEthernet0

  no downtime

  Description connected to the Internet

  IP 172.16.12.20 255.255.224.0

  automatic speed

  KeepAlive 10

  No cdp enable

  !

  ! This access group is also only for test cases!

  !

  no access list 101

  access list 101 ip allow a whole

  !

  local pool IP 192.168.10.1 ippool 192.168.10.10

  IP classless

  IP route 0.0.0.0 0.0.0.0 172.16.12.20

  enable IP pim Bennett

  !

  Line con 0

  exec-timeout 0 0

  password 7 * edit from moderator *.

  line to 0

  line vty 0 4

  !

  end

  ^-^-^-^-^-^-^-^-^-^-^-^-^- snapp ^-^-^-^-^-^-^-^-^-^-^-^-^-^-

  Thomas,

  Can't wait to show something that might be there, but I don't see here. You do not have the card encryption applied to one of the interfaces, perhaps it was not copied. Assuming your description you do it, or should it be, applied to the fa0 and you are connected. Try how you ping? Since the router or a device located on E0? If you ping the router, you will need to do an extended ping of E0 to the ip address of the client has been assigned. If your just ping the router without the extension, you will get sales and decrypts that you declare on the client. Have you tried to ping from the client to interface E0? Your default route on the router is pointing to fa0? You have a next hop to affect? You have several NIC on the client pc? Turn off your other network cards to check that you don't have a problem with routing on the client if you have more than one.

  Kurtis Durrett

• Order of the buttons and the routing of the PS menu does not

  Ugh, this makes me crazy.

  When creating a Blu - ray player, I went through the same steps because I started, but all of a sudden the menus that I create in PS CS5 for Encore CS5 do not work and for the life of me I can't understand why.

  The problem I have is that I put everything up in Photoshop and then import the menu in Encore however when you use a remote control navigation, scrolling down jumps a few buttons and scroll normally.

  For example, let's say I have eight buttons defined in a PSD.

  1

  2

  3

  4

  5

  6

  7

  8

  When I saw or do a test burn, the highlight will stop 1 and 2, but jump 3 and 5 other random button definitions.  And then when it gets to the last, it is not cycle to the first.

  I have everything configured correctly as far as I know - group layers preceded by (+), preceded by cursor highlight (= 1), etc.  And the agenda looks good in yet.

  Extremely frustrated, anyone else having this problem in CS5?  I can up the PSD if someone wants to check.

  Thank you

  Tom

  Thanks for this button routing scheme. Who tells the story.

  When you disable automatically Route buttons, then you can adjust these figures on the four points of the "cross", to define where the navigation will head, as a press arrows. Those who can be set manually now, while the small number in the Middle shows you the number of the button. You are going to use as a reference, you define others (around the cross), to what you want.

  Good luck

  Hunt

• Installs the modem and the router and cannot get it to work?

  Recently, I disconnected and then reconnected my computer laptop Windows 7 and XP desktop to a Linksys router that connects to a cable modem Webstar. I did 4 or 5 times in the past with no problems.
  Two computers can connect with success directly to the modem. When it is connected through the router, they appear connected (i.e. connected to the local network) but cannot access the internet. I tried to switch, reset etc... checked the cables, without success.

  I tried a second router (Belkin Wireless G) I also used before, but get the same result. I appear connected but cannot access the internet, even if I can connect my laptop to other nearby wireless networks.

  If I try to connect from the network schematic page in Windows 7 it tries to connect using a PPPOE (no matter who is and gets a 651 error.

  I tried all the MS diagnosis/troubleshooting software available on Windows 7 but cannot id the problem.

  This should be simple, but I'm out of ideas. Any help would be greatly appreciated.

  For any question on Windows 7:

  http://social.answers.Microsoft.com/forums/en-us/category/Windows7

  Link above is Windows 7 Forum for questions on Windows 7.

  Windows 7 questions should be directed to the it.

  XP forums:

  http://social.answers.Microsoft.com/forums/en-us/category/WindowsXP

  Link above is for XP Forums.

  There is a list of the different Forums XP to the link above to help you.

  You get the help you need there.

  Here is the Vista Forums.

  See you soon

  Mick Murphy - Microsoft partner

• How can I control what "drive and the folder" what creative cloud of loading

  MY boot of the SDS drive is analyzed very tight, I need to load the creative cloud and the MANY applications of my plan to load in and work from my F: drive.

  Thank you. I can't locate any advanced or just load options.

  Alan

  The Solution was in the CC settings > preference > applications tab > files tab

  The cloud control creative program location

  CC App - file locations

  > Open creative cloud App (Image below)

  

  > Right click on it (gear, drop-down) (Image below)

  

  > Select and click on 'Preferences' (Image below)

  Applications TAB >-install Locatotion (F:\Programs)

  The files tab >-location of the folder (F:\)

  

  There you GO! (Image below)

  

  Useful links of video

  https://helpx.Adobe.com/creative-cloud/help/install-apps.html#download and install applications

  Download, installation, setting up

  How to properly set up the SSD as boot drive and the HARD disk as disk storage - YouTube

• OfficeJet 6700: I've just updated my 6700 software and have lost the scan icon and the software - what I can do to fix this?

  I've just updated my software and have lost software and icon of scans!
  What to do to restore it?

  I use Windows 8.1 and trying to connect by wifi for the 6700. The scan icon reappeared today and scanning works now.
  This recovery seems to have fixed things.

• OfficeJet Pro 8600: I got a new modem and the router. I uninstalled the HP software, but wizzard wireless configuration is locked.

  I uninstalled the software so I could start over.  Configuration Wizzard is locked and I can not understand how to get unlock.

  Hi @bobbalou,

  Thank you for visiting the Forums of HP Support for a solution to your printer problem.

  I understand that you replaced your modem and router, but could not connect your HP Officejet Pro 8600 e-all-in-one printer to the new network, because the wireless configuration wizard is locked. I would like to help with that.

  Try to restore the default network before attempting to run the Wireless Setup Wizard.

  1. on the touch screen of the printer, press the right arrow to display the second navigation screen.

  2. press on the installation program icon.

  3. tap network, then press the default network.

  If you are able to restore the default settings of the network is should allow you to run the Wireless Setup Wizard.

  If you're locked up because he had a password set in place on the printer, you will need the password to access the server (EWS) of embedded printer online web to change the settings of the printer.

  

  Please let me know if that solves the problem, or if you need assistance.

• my router cannot find my printer printer how to connect the printer and the router?

  I'm new to computers, as you probably know, and I think it has something to do with the IP address on the prienter.  But that'sd just a guess.  Any help please, it's probably something simple, but I'm clueless as to what to do

  What is the make and model printer?

  No doubt you want to configure for wireless connection, and if so did you use the printer installation cd?

• Click the button and the mouse-(what I need in the text)

  Hi there, sorry to bother the guy again, but I came with a few new questions.

  I want to try with a button click on it has an image apears and disappears, but so far I've only had this piece of code

  botao.addEventListener(MouseEvent.CLICK, mudaimagem); 
  
  
  function mudaimagem (event:MouseEvent):void { 
            if (event.currentTarget.selected == true) {
                      imagem.visible = false;
            }
            else {
                      imagem.visible = true;
   } 
  } 
  
  

  But the thing is... When I press 'CTRL + ENTER', the image is still on the scene and when I click on the button there is no hide not the image.

  I wish I had help to see what I'm doing wrong... I have a deposit that 'If (event.currentTarget.selected is true)"is the wrong thing... but I don't know".

  And also if it is a way to redo the mouse over the button and image apears her disappear when the mouse is not over, I would like to know

  Thanks for the patince and questions of NOOB that I do.

  Cordially ASilva

  All you need to make the image disappear and appear would be...

  botao.addEventListener(MouseEvent.CLICK, mudaimagem);

  function mudaimagem (event:MouseEvent):void {
    imagem.visible = !imagem.visible;
}

  If you want the first invisible object, you must assign them to be so.

  If this does not work what error message you're seeing?

  To do the same thing with a passage of the mouse you would increase the CLICK event to MOUSE_OVER and ROLL_OVER