Installs the modem and the router and cannot get it to work?
Recently, I disconnected and then reconnected my computer laptop Windows 7 and XP desktop to a Linksys router that connects to a cable modem Webstar. I did 4 or 5 times in the past with no problems.
Two computers can connect with success directly to the modem. When it is connected through the router, they appear connected (i.e. connected to the local network) but cannot access the internet. I tried to switch, reset etc... checked the cables, without success.
I tried a second router (Belkin Wireless G) I also used before, but get the same result. I appear connected but cannot access the internet, even if I can connect my laptop to other nearby wireless networks.
If I try to connect from the network schematic page in Windows 7 it tries to connect using a PPPOE (no matter who is and gets a 651 error.
I tried all the MS diagnosis/troubleshooting software available on Windows 7 but cannot id the problem.
This should be simple, but I'm out of ideas. Any help would be greatly appreciated.
For any question on Windows 7:
http://social.answers.Microsoft.com/forums/en-us/category/Windows7
Link above is Windows 7 Forum for questions on Windows 7.
Windows 7 questions should be directed to the it.
XP forums:
http://social.answers.Microsoft.com/forums/en-us/category/WindowsXP
Link above is for XP Forums.
There is a list of the different Forums XP to the link above to help you.
You get the help you need there.
Here is the Vista Forums.
See you soon
Mick Murphy - Microsoft partner
Tags: Windows
Similar Questions
-
"installation is damaged and cannot be opened, you must eject the disk image".
After you download the master creative suite 5 and then try to install the load down, I got this message and could not install the load downwards;
"installation is damaged and cannot be opened, you must eject the disk image".
What does that mean?
IF El Capitan Mac read below
CS6 and previous programs have not been tested and will not be updated to run on Mac El Capitan
-which means you are trying to use CS6 and earlier at YOUR risk of having problems
-You can get CS6 and previous programs to install and run, or you can not (some do, some don't)
-Java https://helpx.adobe.com/dreamweaver/kb/dreamweaver-java-se-6-runtime.html can help
Install CS5 on Mac 10.11 https://forums.adobe.com/thread/2003455 can help (also for others than CS5)
-also a TEMPORARY security change https://forums.adobe.com/thread/2039319
-the guardian https://support.apple.com/en-au/HT202491
-
I want to install the oil for CC for Mac photoshop painting. Where can I find the appropriate download file? When I try to install this "pixelbender_toolkit_2.5.dmg", I get "installation is damaged and cannot be opened.
Oil filter is back in Photoshop was last updated. Just make sure that you have installed.
-
I'm in the Mexico and can browse the web but cannot get the roadrunner site to open the webmail server to allow access to e-mail. I worked around it through another proxy server, but navigation is a pain. does anyone know a solution to this problem? Roadrunner denies that it doesn't clog and so did the modem service here which is telmex?
[moved]
I had the same problem 2 weeks while in the Mexico. I contacted the support TWC and the person to whom I spoke said he had to unlock something. When he did, all my mail came in Outlook in the spam folder. It was OK because I got my mail.
I moved to a different House and now have the same problem again. I've contacted support TWC and not had much luck. The second level support person and I spent more than an hour, the call of the Mexico using Vontage. He has not found anything by the previous call that guided him by setting this time. He said that he would open a ticket and call me in the next 24 to 48 hours.
Is it reminds and solves the problem, I'll post how it was corrected.
Amigos audio!
-
virus: I struggled with the virus for some time and cannot get rid of them
I have struggled with the virus for some time and cannot get rid of them. I bought a few programs, but they have also been infected. any suggestions for a really good virus buster.
Hello
First of all, an antivirus solution to an already infected system of loading is usually pretty useless. The bug will block all attempts to remove or load what it sees as a threat. Second, without knowing which virus you are affected by, it is difficult to be precise.
You can take action include:
(a) work in safe mode, there is much less likely that the virus is able to load and resist actively.
(b) the safe mode, run utilities malwarebytes.org and AV solution that was installed * before * your infection.
(c) post is back with a better description of what is on your system to learn more targeted advice.
Good luck, Rick Rogers, aka "Crazy" - Microsoft MVP http://mvp.support.microsoft.com Windows help - www.rickrogers.org
-
Original title: new printer
I replaced a HP with an Epson Stylus all-in-one printer and cannot get the printer to print more than one page when printing from the computer. The printer works fine when printing from a laptop or ipad!
Start by going here--> http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?UseCookie=yes&oid=232591&prodoid=63099059&infoType=Downloads&platform=nodetect
If the web page has not correctly detected your operating system, select it by using the drop-down list. Rather than using the "Combo package" recommended but huge, expand the "Drivers" section and download driver printer v2.32 to a location that you will remember later.
- Click on the ORB start and go into devices and printers.
- Select (click) the icon of your Epson printer.
- Once you have selected the printer, a button labeled "Print server properties" will appear in the toolbar. Click on this button.
- Click the "Drivers" tab on the print server properties dialog box.
- Select the Epson printer in the list of installed printer drivers, and then click 'remove '.
- In the context menu, select "Remove driver and driver package" and click OK
- Click Yes, and then delete
- Once the removal process is complete, restart the computer (probably not really necessary, but can't hurt)
- Install the driver and the software using the file that you downloaded earlier
At this point, your printer should work fine. However, if you want the ability to print by emailing a file to your printer, you may need to install both 'Remote Printer Driver v1.65' in the category 'Pilot' and "v1.30 utility Configuration of printer Epson Connect" in the "Utilities" category
-
Could not open key
How can I give me access to a registry key? I am trying to install a scanner treated after installation failed previously and I get message "could not open key: UNKNOWN\Components\AFlE7E2767BA2BB41B713A00FB8FACC4\4D7CB2A83D7A5D543B2D9374815CC314.» Verify that you have sufficient access to that key...Click Start, type: regedit
Click with the right button on regedit
Click on run as administrator
Make sure that you back up your Windows registry database before you try:
How to make a backup of the registry in Windows 7
http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry -
Wireless router / Internet problems
I am running Windows Vista Home Edition with Security Essentials. I can connect to my wireless router, but cannot get internet connectivity via Wireless. If I connect the cable to the port on the router, I get internet connectivity. Is there a firewall setting that could cause this problem?Hello
Your router could be suspicious here, you have successfully updated its firmware as a possible solution? And I would like to
Update your WiFi drivers on computers. How you are positioned in the router? Are there
obstacles in the path?Actually try updating your driver and disabling the network logon.
Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlDownload - SAVE - go where you put it - right click – RUN AS ADMIN.
You can download several at once however restart after the installation of each of them.
After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
manufacturer of system become your backup policies).Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
updated drivers.I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
are almost always old, and you can search drivers manually as needed.How to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx------------------------------------------------------
Make sure you know the details of connection to your wireless router - SSID and password.
You lose connection when you do and have to redo your logon.
Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
lower left click on merge or delete network locations - REMOVE all instances of your network (and the
others you don't use anymore) - REBOOT. Start - Connect To log on to the network.-----------------------------------------------------
Check this box:
Strange problem with Internet under Vista
http://www.catonett.com/blog/archives/194Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
http://support.Microsoft.com/kb/928233/en-us----------------------------------------------------
And:
Network connection problems
http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspxI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">->
-
Download says "installation is damaged and cannot be opened".
For the life of me I can't talk to a real person in the customer service! Worst service ever, worse than at & t customer and which is not a little say. I bought the CD years ago and lost and I tried to download Creative suite 5 and it says "installation is damaged and cannot be opened". What should I do?
When you ask a question you will need to provide some basic information
-Forum quick start https://forums.adobe.com/docs/DOC-5601
Mac or Windows and EXACTLY what version of the operating system?
Recent Mac AND Windows operating systems have been known to cause problems "weird."
Using a full account of computer administrator with read/write permission?
IF El Capitan Mac read below
CS6 and previous programs have not been tested and will not be updated to run on Mac El Capitan
-which means you are trying to use CS6 and earlier at YOUR risk of having problems
-You can get CS6 and previous programs to install and run, or you can not (some do, some don't)
-IF not, Details of the message from the error messages and a person may be able to help
Maybe it's a fake because of Mac El Capitan and OLD programs error
This information is a MUST to install old programs on Mac El Capitan
-You can't get the same error message, but here are some links that CAN help with old programs
-Java https://helpx.adobe.com/dreamweaver/kb/dreamweaver-java-se-6-runtime.html can help
Install CS5 on Mac 10.11 https://forums.adobe.com/thread/2003455 can help (also for others than CS5)
-also a TEMPORARY security change https://forums.adobe.com/thread/2039319
-the guardian https://support.apple.com/en-au/HT202491
-
I installed Internet Explorer 8 and cannot get an internet connection...
I installed Internet Explorer 8 and cannot get an internet connection using this program. However, I get a connection very well when I surfed with Firefox. I tried to disable the firewall and still no connectivity. I am connected through a Netgear router with a hard line. The signal is strong. When I run a diagnostic on Internet Explorer, I get a message from the bed... WINDOWS CANNOT CONNECT TO THE INTERNET USING HTTP, HTTPS, OR FTP. THIS IS PROBABLY CAUSED BY THE SETTINGS OF FIREWALL ON THIS COMPUTER.
CHECK THE SETTINGS OF FIREWALL FOR THE HTTP PORT (80), HTTPS PORT (443) AND FTP PORT (21).
YOU MAY NEED TO CONTACT YOUR INTERNET SERVICE PROVIDER OR THE MANUFACTURER OF YOUR FIREWALL SOFTWARE.
No idea how to solve the connection on Internet Explorer?run malwarebytes.
Also, try the following
1. internet options and click the Connections tab
2. and then click LAN settings and uncheck everything.
3. and then click on apply & ok.
MCP. MCDST. LVL 80 -
I have a HP G60-214EM laptop and cannot get it connected to my samsung 26 "smart tv. Can anyone help?
Hello Maureen56,
I understand that you want to connect your TV to your laptop.
To connect your computer to your TV HDTV using an HDMI cable, follow these steps:- Locate the HDMI port on the back of your TV. It should be more than one, in order to choose the one that is otherwise unused. Note the port on which you choose.
-
A pen as a tool with a diagonal line through it appeared that I cannot get rid where work around. He is NOT one of the tools on the standard toolbar. Help please
Means generally that you're trying to work on a layer locked.
-
When I got the laptop - I was able to connect for about 3 days and then nothing - the yellow icon with the! inside he keeps display, or the router icon comes up - there is an internet connection availabe, but after going through all the steps to connect, nothing happens - my router works fine - I use it on another laptop and my desktop computer also works very well - different messages to arrive at different times on the problem. , but no diagnosis has been able to solve the problem.
Hi Diane,
In addition to the advice given, I would have you look at this article and check if the given steps help you correct the problem.
Also, this might be handy in the future.
Thank you!
-
cannot get the keyboard works when reebooting said cd I need driver sata when reebooting he gives four seconds to schrol up to windows xp but the line is highlighted on a windows xp profesional bellows and can't seem to choose windows xp on its own keyboard wont respond but lights from F1 or f2 f3 until f12 choose please help
A few old machines will not recognize a USB keyboard/mouse until after Windows starts. Look at the back of your computer and see if you have a PS/2 (round) connector for a keyboard and a mouse. If you do, then you will need to use a keyboard with a round PS/2 connector or a USB-to-PS/2 adapter and plug the PS/2 connector on the back of your computer so that it recognizes the keyboard until Windows starts on your keyboard.
The SATA driver applies to your hard drive. A CD of start-up/installation of Windows XP does not recognize a SATA hard drive. If you install Windows, you will need to hit F6 at the right time and insert a floppy with the SATA driver on this subject.
HTH,
JW -
I bought 5 Fusion pro and cannot get the VMware Tools to install
Bought a new iMac and bought Fusion 5 Pro. I have a 5 year old and reclassified iMac Fusion 4-5 fusion and had no problems. The new computer is for my wife and I tried and tried to migrate the laptop and it failed every time. So, I did a clean install of Windows 7 and before I downloaded everything that I installed VMWare Tools. For the past 2 days, I was passage of the files from the laptop and install programs that she had on the laptop. Problems with Word and excel as they sit a spin. Money went to re - install VMware Tools and it launches the installation program and then comes up with an error message...
Error 1606: Could Not Access Network Location
\\<host>\users\administrator\my
documents
Went into Windows to uninstall VMware tools and he started the uninstall program then stopped and got the same message. I can not uninstall tools and cannot re - install the tools. I need help to solve this problem. I'm a guy of plug-and-play and if there is code to do, in my opinion, I'm sunk.
Anyone have any ideas on how to solve this problem, so I can get up and go?
Extra solution after Woodys - please check if mirror folder is enabled or not, if it is enabled, please disable it then try to reinstall the tools.
Maybe you are looking for
-
HP d530 CMT stops responding during the recover program
HP d530 CMT stops responding during the installation phase. With the restoration of original hp more cd drive and operating system came with the computer, but it stops on the phase of installation at 35 minutes. Did the restore process several times
-
How can I find my username at my home group so that I can access files on my PC from my laptop - Windows PC Windows7 10
-
BlackBerry Smartphones FORMATTING BB TORCH 9810 MEMORY AND REINSTALLING SOFTWARE
HELLO, I NEED FORMATER COMPLETELY MY BB TORCH 9810 MEMORY AND RELOCATION of the NEW SOFTWARE 7.1... HOW CAN I DO IT BY MYSELF? Thank you very much
-
BlackBerry Smartphones, Opera Mini
I tried to download opera mini and I stopped because he was asking all these questions - signature, http etc... can someone be kind enough to help me with the steps to download and answers - is also mini opera the way to go. Thanks for your help.
-
Slideshow with sensitive photos of height 100%
Hi all.I am doing a slideshow of photos, simple, without thumbnails and the scroll arrows. Only horizontal and vertical photos. But I would like to see ALL the photo every time when I reduce the browser and hidden windows not only some of its parts.M