Multi-site management

Similar Questions

• Question about C60 multi-Site Management

  Dear Expert

  I have a question about C60 multi-Site call using C60 as host.

  It there is a choice of layout as Edge 95?

  My opinion of close end site is not in the page layout and I go through a document to the administrator, apparently not metion on selection of layout on several sites.

  C60 is capable of having a provision such as "4-split' 95 edge?

  Thank you

  Best regards

  Tung

  Current version of the software of C60 TC6.0:

  

  You can also make your own layouts using the TC Console:

  http://developer.Cisco.com/Web/Telepresence-developer/tools/integrators/TC-console

  /Jens

• Codec migration option multi-site since VCSC to CUCM system key

  I have some general questions about this scenario

  If a Codec has multi-site option key and entered a VCSC and is migrated to a CUCM system saved:

  A.) multi-site option button will still be available for use on the Codec?

  (B) can plan for TMS to it, and no need of a conductor based GST to serve the meeting?

  You don't mention what version of endpoint and software, however, the endpoint can use the Multisite option even after it has migrated to CUCM, see sx20-cucm for reference.

  Endpoint can also be using TMS planning conferences that are hosted on microcontroller embedded in endpoint as long that you have added in TMS, please refer to Guides Admin TMS on how to add endpoints CUCM managed in TMS.

• Multi-site architecture view

  Hi, I was wondering if it is possible to deploy architecture view multi-site 5.0 with one instance of vCenter and View Composer.

  I enclose a jpg with the diagram.

  
  Thanks in advance!

  Pablo. -.

  You make very valid points, but I just check our Guide to planning and Architecture on this and we do not specify "in scenarios where a view deployment must cover data centers, create a separate view deployment for each data center." Since the deployment of the view includes vCentert, it really doesn't mean a complete split.

  Power management and cloning would clearly fail in site B while the link is down, and so we really couldn't recommend/support/support it.

  This came from page 43 here http://pubs.vmware.com/view-50/topic/com.vmware.ICbase/PDF/view-50-architecture-planning.pdf

  Select this option.

• Problem adding email address to the site 'Manage your Apple ID'

  I want to add my XYZ e-mail address in the section "reachable to the ' site ' manage your Apple ID. However, I get the following message: "this e-mail address is already in use with another apple ID".

  Note that I have my email set up as my 'rescue email' XYZ on my site ' manage your Apple ID ".

  Could it be the cause of the problem? In other words, the rescue email CAN NOT be used in the section "can be reached to the?

  If it's NOT a problem, then why am I allowed to use my e-mail XYZ as my 'rescue email' address for my Apple ID site, even if he uses another apple ID!

  How can I know what another apple what ID?

  Very confusing to say the least...

  Furthermore, I tried to find a community called 'Apple ID' or 'Messages' of this post "help message" but couldn't find it. "FaceTime" is the closest to what I'm looking for. Please redirect me to the appropriate site if necessary. Thank you!

  Hello Michael,

  Thank you for using communities of Apple support.

  I see you are trying to add an additional email address to your Apple ID. If you already have an address assigned as your email of relief, that is probably why you can't add it as an additional e-mail address. See this support article for more information about Apple ID addresses: on your Apple ID email addresses

  If you want to change the emails, you can replace the recovery email address and use it as an additional e-mail address.

  Best regards.

• The multi site bookmark

  Is it possible to insert a bookmark of the multi site? For example, a click opens 8 sites/tabs. If so, how is this installer?

  To avoid confusion: http://kb.mozillazine.org/JavaScript_is_not_Java

  {Ctrl + click} works like the Middle-click.

• What is the purpose for TMM (Microsoft transient multi-monitor Manager) in Task Scheduler?

  I need some information regarding the purpose and the use of a Scheduler application named TMM or Microsoft transient multi-monitor Manager, please.  Judging by the name of this task, I guess that it is necessary for this application runs when more than one monitor is connected to a computer.  Am I correct in this assumption?

  Because I only have one computer and it has never been more than one monitor hooked up to my computer, do I really have transient multi-monitor Manager Microsoft runs all the time?  If this application does not need to run in my computer, is - it normal that TMM is disabled?

  Janice M. Strunk

  This can be interesting to read. Here is a response from forum Discussion of Vista. Contrary to what you and I thought, this response has proposed.
  http://www.Microsoft.com/communities/newsgroups/en-us/default.aspx?DG=Microsoft.public.Windows.Vista.General&mid=db368e16-dbd1-4654-B644-678d47674c7c&SLOC=en-us

  Enable or disable TMM
  http://www.Vistax64.com/tutorials/115320-Transient-Multimon-Manager-TMM.html

  t-4-2

• Multi-site VPN problem

  Greetings,

  I practice implementation of VPN and it seems to have fallen on a small issue that solution eludes me.  Everything works in my current topology with the exception of a multi-site vpn.  I have 3 ASA, which is outside the interface is connected via a switch.  The inside interface is connected to a local area network that contains a workstation on each subnet.  I'm trying to set up a solution where I can have all 3 ASA related between them via a VPN.  The question I have is when I raise a single tunnel, scathing from a workstation behind the ASA, I can't set up a second tunnel scathing from a different network.  To explain that better, here is an explanation:

  ASA #1

  outdoors: 10.0.1.1/24

  inside: 192.168.0.1/24

  workstation: 192.168.0.100

  ASA #2

  outside: 10.0.1.2/24

  inside: 192.168.1.1/24

  workstation: 192.168.1.100

  ASA #3

  outside: 10.0.1.3/24

  inside: 192.168.2.1/24

  workstation: 192.168.2.100

  If I ping 192.168.0.100 192.168.1.100, the tunnel opens very well and I get answers.  If I can try and ping 192.168.0.100 192.168.2.100, does not open the tunnel to 192.168.2.0.  If I clear all its on ASA #1 and then ping 192.168.0.100 192.168.2.100, the tunnel opens very well and I get a response.  Then I try and ping 192.168.0.100 192.168.1.100 and the same thing happens, no tunnel and no response.  When I enabled logging on ASA #1 seems that it sends the ping for the different network on the tunnel open instead of opening a new tunnel to the correct network.  Can someone tell me what is happening here and if I just missed something simple with routing?  Or is it maybe a problem with VPN?

  Craig,

  You have default route badly configured on all the ASA. Here's what you have configured

  ASA1

  Route outside 0.0.0.0 0.0.0.0 192.168.0.1 1

  It's sendning the package for outside inside IP address. Here's what you need to do on the ASA

  ASA1

  No route outside 0.0.0.0 0.0.0.0 192.168.0.1 1

  Route outside 0.0.0.0 0.0.0.0 10.0.1.2

  ASA2

  No route outside 0.0.0.0 0.0.0.0 192.168.1.1 1

  Route outside 0.0.0.0 0.0.0.0 10.0.1.1

  ASA3

  No route outside 0.0.0.0 0.0.0.0 192.168.2.1 1

  Route outside 0.0.0.0 0.0.0.0 10.0.1.1

  Also delete icmp access list crypto that you allowed to what IP is the same access list. IP covers both the ICMP.

  Kindly let me know change default allows traffic.

  Kind regards

  Bad Boy

  P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community

• What is the Kingdom of multi site profile

  Hi all

  What is an average of Kingdom to ATG? What is the role of the Kingdom in Multi site profile? I went through the docs of the ATG, but I was not able to understand the exact meaning.

  A profile can be associated with a site using profile Kingdom. that means him.

  Thank you

  TT

  Trade Oracle ATG Web - profile realms, it looks like realms of profile allow you to have a single account for multiple sites or allow you to have an account for a group of sites, but not another.

  For example, if you have 3 sites (electronic website, clothing and kitchen utensils Site), you can create a profile named welcome the Kingdom of goods Kingdom that has electronic Site and kitchen utensils and a Kingdom called Kingdom of clothes clothing Site containing profile. If a user creates an account on the website, the account will allow you to connect on the Site of kitchen utensils, but not the Site of clothing because the site of kitchenware is in the same domain and clothing is not. To connect on clothing, you need to create an account on a site in this area.

  Thank you

  Joe

• Error opening Multi-hypervisor Manager - sever fault "NoPermission" got no message.

  I installed vCentre Multihypervisior in a test environment running vCenter 5.5.  As it is to test, I installed components on the server using the administrator account for the domain side. Service runs on the VC server.

  have also installed the client component on the VC Server also. When to launch the vSphere client and by launching the "Multi-hypervisor Manager vCentre" Plugin, I get the following error message, I attach too.

  The flaw of sever "NoPermission" has no message.

  The administrator seems to have full access to vCenter inventory.

  Any ideas?

  Thank you very much

  Hello

  During the installation of MHM, you used an administrative user of VC (see screenshot below). This user becomes the default administrator for MHM inventory. Can you please try to connect with this user.

  VC permissions and authorization of MHM are separated.

  Thank you

  -Marcel

• What happened to all the options under Site Manager?

  There used to be tons of options under the Site Manager:

  Pages

  Page templates

  Module templates

  Menus of content holders

  Web Forms

  File Manager

  Etc.

  Now I only have two:

  Web Forms

  E-mail system

  What happened to all the additional options, and how do I access them now? Looks like it happened only since the updates of BC.

  I have a Plan of Ecommerce BC, so I should have everything.

  If it was something simple. I created a ticket and the response returned. I clicked on "my data" under my name at the top on the right. Then, I checked and enabled "edition of content". Somehow he must have been disabled because I used Muse.

• Why can't I add a box securely in site manager?

  I can't add a box secured to my site from muse. Why the option in the site manager is not available?

  IF you do not see that and other options that you are not on a BC plan that supports these features, and if you would like to upgrade.

• Menu site Manager

  So I just upgraded BC basic web with creative cloud to Electronic Commerce.

  When I log in BC I'll add a secure area and I see in the list in the Site Manager is Web Forms and email system. Where is the rest of the list? How can I get the full list that you get when you start a free trial version?

  Thanks in advance

  Luke

  Hi Luke,.

  "In the administration panel, on the side back to the top right, click on my details under your name, scroll a bit down and check the box"Enable editing for online content"and click on save," refresh your web page. You should have all the options

• DW CC 2014 Site manager deletes the credentials

  I have a site that I regularly use that has no problems in CC of DW, but since the upgrade by 2014, whenever I start DW I got in Manager of site/servers and re - enter my user name and password before it will transfer or synchronize. It is configured to save, but it won't save Oh my credentials at the exit. Other sites is not a problem. Is there anything I can do to refresh works this site so that the credentials are saved?

  I deleted the Site Manager site and created a new site. This seemed to fix it.

• Lack of drop down in the Site Manager

  I am designing the presentation for my layout of product e-commerce (Ecommerce BC and Muse) - watch the video support/training it is assumed that me several options in the Site Manager. I don't have Web Forms and email system.

  I don't have a page; module templates, etc.

  Any suggestions or knowledge available?

  Thank you-

  Hello

  Please activate the edition online by going to my details > scroll down > enable editing online.

  It would also depend on the plan of the site you have selected.

  Thank you

  Sanjit