Must install Labview App on cFP2200 with feature plug & play for measurement modules

Similar Questions

• Installing LabVIEW 8.2.1 with DAQmx 8.0 on Suse 10.3 for Linux.

  We have recently updated some of our machines to Opensuse 10.3.  We have a set of instructions, that my Advisor has written that have been used for installing Labview 8.2.1 and 1.6 NATION DAQmx 8.0 on Opensuse 10.3.  I thought I would post these instructions for any person who may find them useful.

  NATION is now on version 1.7 and we began to use that, but not as of the most recent writing of these instructions.  We have installed Labview 8.5 by following these instructions as well, but they have not been modified for that either.  I used these instructions to install Labview 8.5, NATION DAQmx base 1.7 and 3.1 on a laptop since we need supported USB for a NI 9233.  It is installed without problem. I changed the following:

  On step 10, the version of NATION was 1.7 1.6 not.
  In step 11. I installed DAQmx Base 1.3 instead of DAQmx 8.0 and the message about Labview 8.0 is not being installed does not occur.
  Steps 13 and 14 should not be necessary since the DAQmx Base and Labview versions likely mutually wait to be there.

  Once I had everything installed on the laptop, Labview didn't see my camera.  I contacted NEITHER and they were very helpful and offered a few commands to run.  Here's what I did.

  I ran "lsdaq" with the following result:

  > --------------------------------
  >
  > Detection of National Instruments DAQ devices
  >
  > Find the following materials:
  >
  > OR USB-9233: "Dev1" (USB0::0x3923:0x70A8:01369063: RAW)
  >
  > --------------------------------

  So I ran "mxbaseconfig" with this error as output:
  >
  > LabVIEW caught fatal signal
  >
  SIGSEGV > 8.2.1 - received
  >
  > Reason: address not mapped to the object
  >
  > Try to reference address: 0x0
  >
  >/usr/local/bin/mxbaseconfig: line 7: 18984 Segmentation fault
  >/etc/natinst/nidaqmxbase/bin/mxbaseconfiglv

  So I ran "/ usr/local/natinst/nidaqmxbase/bin/dmxbUSBfirmware.sh" with this error
  >
  > /usr/local/natinst/nidaqmxbase/bin/dmxbUSBfirmware.sh: line 9:19214
  >/Etc/natinst/nidaqmxbase/bin/niusb9162dlfw failed

  Finally, I ran "updateNIDrivers" as root but Labview has not yet see the USB card.  It was suggested then manually enter "Dev1/ai0' as the physical channel in an example DAQmx Base VI, and it worked perfectly.  Everthything seems fully functional and I had no problem running the four tracks of the card.  Sorry for the long post, just thought I would post this information where a person is in a similar situation.

  Jeff

  Jeff,

  Support for the USB-9234 DAQmx Base was added to version 3.2. All you have to do is to level 3.1 to 3.2. Here is the download link:

  DAQmx Base 3.2
  http://Joule.NI.com/nidu/CDs/view/p/ID/1076/lang/en

  Kind regards

• SMU 8135 cannot ping pc when installing labview

  HJ. Help me

  my laptop do not install labview 2012 can ping with SMU 8135 but labview installed on my laptop cannot ping with SMU 8135. I don't understand

  Hi ffefef,

  Could you explain in more detail the question, you encounter?

  Thank you

• LabVIEW 8.0 works with IMAQ USB? If so, should which version I install?

  Hi, guys.

  LabVIEW 8.0 works with IMAQ USB? If so, should which version I install?

  Thank you very much!

  Have you seen this.

  Years for your questions, I guess it will be better for you if you stick to a single thread.

• Problem with installing an app that requires internet

  Whenever I try to install the torch using a wi - fi connection, it takes almost 7 min, then he said: "we could not all facilities due to internet related problems. What do you propose, I do with my settings, because when I dissable: use the proxy. It disconnects completely my browsers.

  Hello

  When you use connection proxy to connect to the Internet, then you will not be able to use all the apps. This is the reason why you're not able to install apps. I suggest to disable the proxy and then try to install the app and check if it helps.

  You can also try the steps in the Microsoft Help article and check if it works for you.

  Why can't find or install the application on the Windows Store?

  http://Windows.Microsoft.com/en-us/Windows-8/why-find-install-app-Windows-store

  For more information, you can consult the following Microsoft Help article.

  http://Windows.Microsoft.com/en-us/Windows-8/what-troubleshoot-problems-app

  Please reply with the status of the issue, so that we can confirm that the issue is resolved.

• problem with MAX after installing LABVIEW 10

  Hello everyone, I have a serious problem I installed labview 10 yesterday on 2 laptops, one of them works perfectly, however, the other gave me a two erros

  1.http://digital.ni.com/public.nsf/allkb/6CA56E2DDBCCA06086257591006141EE

  2. http://digital.ni.com/public.nsf/allkb/F24AA9FB6A3A0E9D86257539006141BE

  I tried the solutions above in the link, but it was all futile. can someone please suggest me what would be the problem? I had already LV8.0 on the laptop which is the cause of the problem. I tried to re - install the disk driver given

  for me by NEITHER, but no luck.

  When I started the laptop for the 1st time, there was a mistake in saying DOS command prompt: DATABASE ERROR and I cancelled the error!

  In addition, Labview works fine, its only MAX who has problems. is there a way I can only MAX to uninstall and reinstall? Please help me...

  Thank you

  Sorry CrackJack

  Try this one http://digital.ni.com/public.nsf/allkb/86256F0E001DA9FF86256FFD005B827C?OpenDocument    

• Put in Server cache does not cache its own installed on App Store

  I've set up the OS X Server App 5.1.5 (15S 7047) on an iMac running El Capitan 10.11.5 (Build 15F34). The iMac has 8 GB of Ram and a processor i5. It's mid-2011.

  He belongs to a Windows domain and put in a Time Capsule in Bridge mode.

  On the iMac's settings, etc.. :

  Overview of the server:

  Internet: Can be reached at 202.etc., no service available

  Public host name: no

  Network interface: Ethernet, Ip address 192.168.0.70 (assigned by DHCP - not static, but it never changes)

  Accounts: All users, all groups (filled by the domain Windows - Active Directory for the Windows domain controller).

  Only the caching Service is enabled.

  The said status caching service "available - devices on your local network automatically uses this service."

  Permissions: Only the local subnets

  Serve customers with public addresses: mapping network from this server.

  ICloud data: unchecked data cache personal iCloud

  Available cache: 150 GB

  Use cache: None

  When installing from the App Store, the cache is unchanged - still nothing.

  I also downloaded a MacBook Pro and nothing is cached as well.

  I'm new to Mac and must have missed a few settings, but have read a lot on various Forums. I suspect the accessibility by saying 'no available services' cannot be part of the problem.

  I checked the logs - log service for caching can help. The first installation of the application server was a week ago, and I see a problem with "black list... demand." "(see below)

  About 12:15 today, I uninstalled the application server by moving it to the trash, removed the Library\Server, etc. then installed the App Server again. Now the failed activity is not currently recorded.

  PART OF THE FIRST INSTALLATION OF THE APP SERVER FOR CACHING OF LOG FOR TODAY:

  June 20 at 11:14:10 dlserver AssetCache [351]: server closing caching (15)

  June 20 at 11:14:10 dlserver com.apple.xpc.launchd [1] (com.apple.AssetCache [351]): Service came out with abnormal code: 15

  June 20 at 11:14:34 dlserver AssetCache [1110]: Server version 149.4 started caching

  June 20 at 11:14:37 dlserver AssetCache [1110]: successful registration.  Recovery of the server.

  June 20 at 11:41:56 dlserver AssetCache [321]: Server version 149.4 started caching

  20 Jun 11:41:57 dlserver AssetCache [321]: request for http://suconfig.apple.com/resource/registration/v1/config.plist configuration failed: the Internet connection appears to be offline.

  20 June-11:41:57 dlserver AssetCache [321]: back to the last accepted configuration

  20 June-11:41:57 dlserver AssetCache [321]: http://suconfig.apple.com/resource/registration/v1/blacklist.plist blacklist request failed: the Internet connection appears to be offline.

  20 June-11:41:57 dlserver AssetCache [321]: chess 1 consecutive cleaning.  Retries in 16 seconds.

  June 20 at 11:42:18 dlserver AssetCache [321]: successful registration.  Recovery of the server.

  June 21 at 08:55:28 dlserver AssetCache [319]: Server version 149.4 started caching

  June 21 at 08:55:28 dlserver AssetCache [319]: application of http://suconfig.apple.com/resource/registration/v1/config.plist configuration failed: the Internet connection appears to be offline.

  June 21 at 08:55:28 dlserver AssetCache [319]: back to the last accepted configuration

  June 21 at 08:55:43 dlserver AssetCache [319]: successful registration.  Recovery of the server.

  June 21 at 10:07:47 dlserver AssetCache [334]: Server version 149.4 started caching

  June 21 at 10:07:49 dlserver AssetCache [334]: application of http://suconfig.apple.com/resource/registration/v1/config.plist configuration failed: the Internet connection appears to be offline.

  June 21 at 10:07:49 dlserver AssetCache [334]: back to the last accepted configuration

  June 21 at 10:07:52 dlserver AssetCache [334]: http://suconfig.apple.com/resource/registration/v1/blacklist.plist blacklist request failed: the Internet connection appears to be offline.

  June 21 at 10:07:52 dlserver AssetCache [334]: chess 1 consecutive cleaning.  Retries in 63 seconds.

  June 21 at 10:09:07 dlserver AssetCache [334]: successful registration.  Recovery of the server.

  June 21 at 10:15:53 dlserver AssetCache [307]: Server version 149.4 started caching

  June 21 at 10:15:53 dlserver AssetCache [307]: application of http://suconfig.apple.com/resource/registration/v1/config.plist configuration failed: the Internet connection appears to be offline.

  June 21 at 10:15:53 dlserver AssetCache [307]: back to the last accepted configuration

  June 21 at 10:15:57 dlserver AssetCache [307]: http://suconfig.apple.com/resource/registration/v1/blacklist.plist blacklist request failed: the Internet connection appears to be offline.

  June 21 at 10:15:57 dlserver AssetCache [307]: chess 1 consecutive cleaning.  Retries in 60 seconds.

  21 June 10:17 dlserver AssetCache [307]: successful registration.  Recovery of the server.

  June 21 at 12:05:11 dlserver AssetCache [287]: Server version 149.4 started caching

  June 21 at 12:05:13 dlserver AssetCache [287]: application of http://suconfig.apple.com/resource/registration/v1/config.plist configuration failed: the Internet connection appears to be offline.

  June 21 at 12:05:13 dlserver AssetCache [287]: back to the last accepted configuration

  June 21 at 12:05:13 dlserver AssetCache [287]: http://suconfig.apple.com/resource/registration/v1/blacklist.plist blacklist request failed: the Internet connection appears to be offline.

  June 21 at 12:05:13 dlserver AssetCache [287]: chess 1 consecutive cleaning.  Retries in 72 seconds.

  June 21 at 12:06:30 dlserver AssetCache [287]: successful registration.  Recovery of the server.

  June 21-12:14:36 dlserver AssetCache [287]: server closing caching (15)

  June 21-12:14:36 dlserver com.apple.xpc.launchd [1] (com.apple.AssetCache [287]): Service came out with abnormal code: 15

  (THIS IS THE POINT WHEN THE APP SERVER HAS BEEN REINSTALLED)

  21 June at 14:55:50 dlserver AssetCache [2986]: Server version 149.4 started caching

  21 June at 14:55:54 dlserver AssetCache [2986]: successful registration.  Recovery of the server.

  BUT STILL NO CACHING OF HIS PEOPLE MOVED FROM THE APP STORE.

  I also tried it with OS X Firewall disabled, Avira Real - Time Protection off tension, but nothing is.

  I suspect the State available services no. for the Internet parameter, mentioned at the beginning of this post, to be meaningful, but did not find what is missing.

  I thank very you much for any help.

  Update:

  After downloading a few elements of the App Store, this poster now implementing log cache (again). I have certainly given internet I installed from the App Store:

  June 22 at 09:50:12 dlserver AssetCache [314]: Server version 149.4 started caching

  June 22 at 09:50:12 dlserver AssetCache [314]: request for http://suconfig.apple.com/resource/registration/v1/config.plist configuration failed: the Internet connection appears to be offline.

  June 22 at 09:50:12 dlserver AssetCache [314]: back to the last accepted configuration

  June 22 at 09:50:12 dlserver AssetCache [314]: http://suconfig.apple.com/resource/registration/v1/blacklist.plist blacklist request failed: the Internet connection appears to be offline.

  June 22 at 09:50:12 dlserver AssetCache [314]: chess 1 consecutive cleaning.  Retries in 74 seconds.

  June 22 at 09:51:40 dlserver AssetCache [314]: successful registration.  Recovery of the server.

  And nothing is recorded in the Server Cache.

• 9.30 NIDAQ drivers not install LabVIEW 2011 - example. Microsoft .com's in LabVIEW 2010 under vi.llb

  I just upgraded to LabVIEW 2011 without uninstalling LabVIEW 2010.  I downloaded the last set of drivers DAQmx 9.30.  I find that these drivers are installed in a DAQmx folder under the vi.llb of theLabVIEW 2010 and NOT in the vi.llb of LabVIEW 2011.  The DAQmx features do not appear on the menus and the existing instances are reported as 'cannot be compiled. How can I get the DAQmx functions to properly install LabVIEW 2011?

  You must DAQmx 9.4.

  9.4 DAQmx

• Windows 7 takes 15 min to start after installing Labview 2012

  Hello

  I need help on this, is this a bug?

  The problem is that on my laptop after installing Labview 2012, it takes about 15 minutes to start, this happens every time a restart or start my laptop.

  At first I thought something with my laptop, but then my colleague also installed Labview 2012 on his laptop and has exactly the same problem, the difference is that his new laptop and is running windows 7 Professional 64-bit, mine is older and is currently running windows 7 32-bit professional.

  I tried to disable the services NOR, but has not solved the problem, but when I disable all windows services that start at startup, the startup is fast.

  Also note that I had Labview 2011 installed before and I didn't have this problem before.

  Tried also to find something in the registry, but nothing.

  Any who have this problem, or a solution to this?

  Thanks in advance

  This problem seems to be resolved, but then he come back again a few days later

  I did many tests in my laptop and found it to be in the "Service of Network Store Interface" service (INS). Disabling this service, you have your problem solved, but there is another problem, you lose the network.
  This happens because the "DHCP Client" service depends on the national statistical institutes.

  Also, this issue seems to occur only when the PC is in a domain and I'm in a windows server (Windows SBS2008) domain.

  Then I found that if you set manual this services which depend on national institutes of statistics (DHCP Client, DNS Client, IP Helper, network connections, local awareness network) and also put INS manual
  You must also disable the "Workstation" service that also depends on national institutes of statistics (why turn off? Because there are 3 services that depend on the workstation service, they will require to start, and then it will force NSIS to start, then long boot, if you really need of the dependent services on workstation, do the same as for them)
  Not also need uncheck this services in msconfig window if they are checked, and then the PC will boot normally without a network.

  When you start, you should go to services and start the DHCP Client for the network (and the other if you really need)
  This will force also NSIS to start and other services that depend on the national statistical institutes.
  The first time the PC restarts, you may need to reset these services to manual in the services window, I had to do, and then in sebsequent boots, they have been already set to manual
  If you leave right on the dependent services in automatic or automatic (delayed start) it will force NSIS to run and start time will go to + - 15 min

  Because you must manually start "DHCP Client" for the network, here's a solution to do it automatically after have connected you:
  1 - Go to control panel, and then open administrative tools
  Task 2-open Scheduller
  3. on the right click "Creat fundamental task.
  4. in the first window give a name ("DHCP" for example) and press next
  5 - Click on "When I Logon" and press next
  6 - click on "Start a program", and then press next
  7. in the "program/script" insert: net
  8. in the "Arguments" insert: start "DHCP Client".
  9 - Press 'Finish' and you're done

• How to install module DSC without installing LabVIEW

  Hello.

  I build exe with the functions of the dsc module (I used an opc server). In my computer, it's work very well. Earlier, I want to create the installer for another computer. I have check all Inc. in the other installers. And build.

  I install my installer in another computer, but I can not create opc client. In services, I find national engine Instrument variable. Its engine description i/o for LabVIEW and LabVIEW DSC. There is prksent ( http://www.ni.com/white-paper/11843/en#189456_by_Category ) that I need to install the DSC module. But when I try to install the dsc module it shows error like "OR LabVIEW 2010 must be installed before you can install Module NI LabVIEW 2010 Dataloging and monitoring control". So, how can I install DSC module in third computer without installing LabVIEW to run exe, where opc client functions.

  Hi, a LabVIEW executable that will run on a target computer requires the engine run LabVIEW version in which the code has been developed more, any other runtime related to the application, in your case: + the Runtime Module of DSC system. Here is an article that can answer your question and the Readme file for installation instructions.

• How to install LabVIEW 7.0 on PXI-8186 RT

  I try to install LabVIEW 7.0 in real-time on a PXI-8186 controller.  It took a lot of time to go through the process, and it still does not, so I write this message in part to help and partly to document which does not work for later use.  The controller provided with Windows XP installed.  I created a bootable Windows 98 (of http://www.allbootdisks.com/download/98.html) floppy.  I plugged in an external USB drive on the PXI-8186 controller.  The hard drive would be recognized only when the BIOS setting specified startup in Windows / other OS.  I brought to the top of the BIOS setting screen by pressing the delete key several times after turning on the chassis (hold the DELETE key and turn on the chassis do not provide the BIOS settings.  In the BIOS setting, I went to the tab 'LabVIEW RT' and changed the "Startup Configuration:" to "Windows / other OS.

  I then started using the Windows 98 Startup disk and ran Fdisk

  Using fdisk, I deleted the existing partition and creates a new main back partition with the size of the complete volume.

  I then restarted the computer, once again starting with the Windows 98 Startup disk and formatted the C drive with the command "format C:".

  "When the format was finished, I used MAX Version 4.5.0f0 and some tools of-> RT Disk Utilities-> create PXI Format hard drive.

  I selected the Version 7.0 in the dropdown menu, complete the initialization of the disk without any problems and then used the resulting so that it starts the PXI chassis.

  PXI started with the message 'Transfer control user program.' followed by a 11 lines from "WARNING KERNEL.346530: error initializing floppy A:" followed by a prompt to re - format the C: drive.  I typed "Yes".

  Then the following message appears:

  Hard drive recovery to start in o/s real-time...

  WARNING KERNEL.346530: Error initializing floppy drive A:

  WARNING KERNEL.346530: Error initializing floppy drive A:

  Change the drive target C:\hdmon.bin for a start.

  Copy the host hdmon.bin target C:\hdmon.bin...

  Error: Could not open source file hdmon.bin

  Impossible to set up the hard drive boot sector.

  At this point, I can enter the BIOS and configure the computer to start in LabVIEW RT and I get the following message:

  "Could not load the LabVIEW RT of the player!

  Boot mode safe of Romans...

  Enter safe mode.

  The IP address is: 0.0.0.0

  At this point, I can connect it to the chassis of MAX and assign an IP address.  I can also install LabVIEW 8.6 real-time without problem.  However, I can't get LabVIEW 7.0 installed in real time.  It is clear to me if in time real LabVIEW 7.0 must be installed using a diskette or by software 'install' button in MAX.  If I try to use the button 'Install Software', the only version of real time available is "8.6".  When I do "PXI Format hard drive", I see an option "7.0" or a "8.6".  Also, I tried to connect it to the chassis with 2 other computers, which have all two LabVIEW 7.0 installed in real time.

  I saw an article in the knowledge base that says that LabVIEW 7.0 is supported on the PXI-8186 (http://digital.ni.com/public.nsf/allkb/B35E022CF91F6EF086256E68005FBC29) controller and another link which explains that an additional CD can be used to install the software (LabVIEW RT software does not exist on the Local host for PXI-8186 controller: http://digital.ni.com/public.nsf/websearch/4655C86B65AE7A7286256E620004834C?OpenDocument _)

  However, this knowledge base made from 24/03/2004 and I have not received any CD entitled "The LabVIEW Real-time Embedded Software CD.  I got a CD "embedded controller OR ', but it was not obvious to me how to use it.  He has an "I386" folder and a "BONE" record on this matter.

  Any help appreciated.

  After a Chase, the CD mentioned in the knowledge base has been found ("LabVIEW Real-time Embedded Software CD").  I put this CD on a computer that had at the time real LabVIEW 7.0 and Max Version 3.0.2 in it.  The Setup program ran, I installed LabVIEW 6.1 and 7.0 support and the installation tree showed that the support would be added for PXI-818 x controllers.  After running the program, I was able to install the software for the PXI-8186 and things worked as explained in the knowledge base.

  The CD mentioned also ran on my laptop, which has MAX version 4.5.0f0.  However, you are using the latest version of MAX, I don't have the ability to install LabVIEW 7.0 in real-time on the PXI-8186 controller since the button to install the software.  I looked briefly using MAX, but I could not know if it is a bug with the latest version of the Drivers of OR or a voluntary choice of National Instruments for support not time real LabVIEW 7.0 in newer versions.

• I am trying to install free apps from the store and I get "your purchase could not be executed. Please try again.

  I am trying to install free apps from the store and I get "your purchase could not be executed. Please try again.  He told me to add the payment method before apps can be purchased. A pop up with adding payments happens, but I can't activate it.  Where can else I add my mode of payment on my profile?

  Original title: payment

  Open the store and open bar charms and select "settings".  Then click on 'your account '.  You must finish setting up your account before you can get apps.  Although the apps you're looking for are 'free', you will not be charged for them, but the account setup must be run.

• Adobe Creative Cloud - install Adobe Apps button does not

  Hi, I wanted to test the Adobe Premiere Pro on my machine Windows 8.1. It seems, that there is no stand-alone installation option, but you must install the application on Adobe Creative cloud with your Adobe ID to now it will. Installed the creative cloud connected with my Adobe ID but, when I try to install the trial version of Premiere Pro, I can't do it, in fact I can't install apps with this client. In terms of the House, he says "your RSS home is empty, if I click on the 'Install Adobe Apps' button, nothing happens, no event fired. No process at all. It looks familiar to this problem, so I followed the solutions here: Adobe Creative Cloud desktop application does not open or shows a spinning wheel of progress

  It did not work. When I go to my Adobe ID online and choose where to install desktop applications, I get redirected to the Premiere Pro page, where she still fine creative Cloud customer. But back in the loop.

  Everything seems to go well with my Adobe or my system, but somehow can't see all applications. Should I have done something else or further with the purchase of test maybe version? There is also no Apps next at home, resources, Stock and community section. Is this a known issue? If so, could you please point to the right direction? If this isn't the case, you have a solution to this? If any other information is needed, please say so. Thank you very much!

  Post edited by: Emre Taspolatoglu - TYPOS

  White screen

  https://forums.Adobe.com/thread/1249756

• How to install (created with Adobe Air) ipa for ipad

  Dear friends,

  I created an ipad app using Adobe Air. It works fine when I compile and I did a package by using a certificate created with mac computer and a .p12 also. I created a file ipa, that it connects with itune and I can install... after installation, the icon and the app will auto-hide or uninstall of form my ipad. What is the reason. Please help me install my ipa file created with Adobe air to ipad6. I used developer certificate as well as ad-hoc too... both give the same error... just install and immediately hiding or uninstall. pls help me.

  Thank you and best regards,

  Syed Abdul Rahim

  It must match the id of the page of an apple developer certificate bundle:

  

• Installed update app

  I have a problem for a long time now.

  One of my friends gave me a cool app, it has purchased, through USB key. Of course, I need his Apple ID, to install updates.

  I didn't ask him his ID and password, so I decided to uninstall the application.

  The problem is that there is always an update on the Mac App Store, which is really annoying, because of the number in the Dock over the Mac App Store sign.

  If I want to install the update, Mac Apps Store asks me my friends Apple ID password.

  I would be very grateful if someone could help me with this question.

  Best regards

  Your solutions is quite simple. Download on the App Store, if that of where he came, locate the application and download it using your Apple ID and password. If this is not a free app, then you will have to pay for it.

  Only your friend can give you his Apple ID and password. If he does while it is crazy to do. And you're not much of a friend to ask him.