SMU 8135 cannot ping pc when installing labview

Similar Questions

• NLB - two virtual machines can't ping eachother when on separate hosts

  Greetings,

  I've been running some tests with NLB on the different desks as recommended here:

  http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC & docType = kc & externalId = 1006558 & sliceId = 1 & docTypeID = DT_KB_1_1 & dialogID = 42912404 & StateID = 0% 200% 2041454115

  http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC & docType = kc & externalId = 1006778 & sliceId = 1 & docTypeID = DT_KB_1_1 & dialogID = 42912404 & StateID = 0% 200% 2041454115

  I found that Unicast works better in our network environment, but it is still a problem:

  In http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC & docType = kc & externalId = 1006580 & sliceId = 1 & docTypeID = DT_KB_1_1 & dialogID = 42912690 & StateID = 0% 200% 2041454807

  He says: "since all hosts in the cluster have the same IP Address and the same MAC address, there is no communication possible inter-hote between the hosts configured in unicast mode.» A second NETWORK adapter is required for any other host communication. »

  However, even with a second NETWORK adapter the virtual machines cannot ping eachother when they are on a different esx host. When they are on the same host esx virtual machines can ping each other. Also, when they are on different hosts, so that a virtual machine cannot reach each other on their dedicated IP address, virtual machines can reach other when ping the second card NETWORK (the one without an informed gateway).

  For example, the next 2 guests are connected unicast:

  VM1 has 2 network cards, NIC1 = 172.18.18.41 with gateway (dedicated IP) and NIC2 = 172.18.18.43 without gateway / WLBS enabled.

  VM2 has 2 network cards, NIC1 = 172.18.18.42 with gateway (dedicated IP) and NIC2 = 172.18.18.44 without gateway / WLBS enabled.

  When on the same ESX host VM1 can reach VM2 on 172.18.18.42 and 172.18.18.44, and vice versa.

  When on ESX different hosts VM1 cannot reach VM2 on 172.18.18.42 but it can reach VM2 thanks 172.18.18.44. In this case VM2 cannot reach VM1 on 172.18.18.41 but can reach VM1 on 172.18.18.43.

  I followed and applied the settings recommended in this article: http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC & docType = kc & externalId = 1556 & sliceId = 1 & docTypeID = DT_KB_1_1 & dialogID = 42912404 & StateID = 0% 200% 2041454115

  I even tried the kb from microsoft as shown here: http://support.Microsoft.com/kb/898867 even if the virtual machines have 2 network cards, but of course that did not help either.

  Does anyone have an idea what is happening here?

  The fact that it works on the same host, but not on different hosts type advanced to a network within VMware issue.

  Thanks in advance,

  Bram

  It seems that ir can be a problem of IP routing, even with the hosts on the same subnet.  Make sure that your routing table that traffic on each that is to/from your mgmt that ips turns off your local management interface.  If it isn't, then update your routing table in order to.

  Or, you could try setting up your mgmt network cards on a different subnet from your IP NLB.  I suspect that this will solve the problem.

  JP

• get the message "setup.exe has stopped working" when trying to install labview 2011 or 2012 on a windows machine 7

  When you try to install labview 2011 or 2012 on a windows machine 7, I get a message "setup.exe has stopped working". I tried to run setup.exe as an administrator with the same results. I have Microsoft .NET Framework installed on the affected machine 4.5.1. Could be the cause of this problem? Or does anyone know the root cause of this error?

  Hi - are you getting it at the beginning of installation, during or after 100% progression ended?

  Is it fair to LabVIEW you install, or is it drivers too, in this case, what was the last big package that has been installed at the time?

  This can be caused by the NVIDIA chipset driver:

  https://decibel.NI.com/content/message/46299?TSTART=-130

  Thank you
  Sacha

• Cannot hear sound when it is online and when trying to install flash player then it show ATL file DLL missing, please reinstall the program

  Cannot hear sound when it is online and when trying to install flash player then it show ATL file DLL missing, please reinstall the program

  Hello

  We are pleased to hear that you were able to find a solution to the question and I thank you for the information provided. Do not hesitate to contact us, in the case where you face other problems in the future.

• Error "Windows Setup cannot continue. To install windows, click ok to restart the computer, and then restart the installation. "When you try to install Windows.

  How can I configure my windows 7 after restoring my laptop to the factory conditians?

  My laptop had a blue screen and I couldn't get rid of it, I went into safe mode and restore my computer to factory conditions. When the computer says "the installation program starts services" you stop and I couldn't turn it back on for 15 minutes. When I turned on and tried to contained my setup, a message keeps poping up "the computer restarted unexpectedly or encountered an unexpected error." Windows Setup cannot continue. To install windows, click ok to restart the computer, and then restart the installation. "But no mader, how many times I reboot my laptop, the same message appears. What should I do? I've restored my computer several times and never had this problem.

  You should try another recovery.

  New computers coming often pre-installed with Windows 7 have what is called a recovery partition. This is used to reinstall an operating system in the case of a system failure. To access it, you need to start when you start your computer by pressing a function key. This can be either F1, F2, F9, F10, F11, F12 key DEL or tab. See the manual that came with your PC for instructions on how to reinstall Windows.

  If your recovery partition is not available or damaged, you must contact the manufacturer of your computer, and request that a defined recovery disk you can use to reinstall Windows 7. They could practice a small shipping and handling.

• Error when using product key "its product key cannot be used to install a version of window" 8

  Original title: Windows ISO file.

  Hai,

  I have a computer Dell laptop with windows pre-installed 8, and I want to do a clean install due to some problems. I downloaded the windows in order to get the iso file from this link; http://Windows.Microsoft.com/en-us/Windows-8/upgrade-product-key-only

  But when I launch the series to the top and entered the product key, notice presented themselves: this product key cannot be used to install a version 8 window retail.

  So, could you help me to advise where I can get the iso file?

  Thanks in advance!

  Hello

  Computers production come with a manufacturer OEM check so with Dell technical support, their line of license
  documentation and ask in their forums.

  How to restore or reinstall Microsoft Windows on a Dell computer
  http://www.Dell.com/support/article/us/en/04/DSN_347576/en

  Dell support
  http://support.Dell.com/

  Dell support drivers - product manual & warranty Info (left side) - and much more
  http://support.Dell.com/support/index.aspx?c=us&l=en&s=DHS

  Dell forums
  http://en.community.Dell.com/forums/

  Dell PC Diagnostics
  http://www.Dell.com/support/Diagnostics/us/en/19/

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Cannot ping via the VPN client host when static NAT translations are used

  Hello, I have a SRI 3825 configured for Cisco VPN client access.

  There are also several hosts on the internal network of the static NAT translations have a services facing outwards.

  Everything works as expected with the exception that I cannot ping hosts on the internal network once connected via VPN client that is internal IP addresses have the static NAT translations in external public addresses, I ping any host that does not have static NAT translation.

  For example, in the example below, I cannot ping 192.168.1.1 and 192.168.1.2, but I can ping to the internal interface of the router, and any other host on the LAN, I can ping all hosts in the router itself.

  Any help would be appreciated.

  Concerning

  !

  session of crypto consignment

  !

  crypto ISAKMP policy 10

  BA 3des

  preshared authentication

  Group 2

  !

  ISAKMP crypto client configuration group vpnclient

  key S3Cu4Ke!

  DNS 192.168.1.1 192.168.1.2

  domain domain.com

  pool dhcppool

  ACL 198

  Save-password

  PFS

  netmask 255.255.255.0

  !

  !

  Crypto ipsec transform-set-SECURE 3DES esp-3des esp-sha-hmac

  !

  Crypto-map dynamic dynmap 10

  86400 seconds, life of security association set

  game of transformation-3DES-SECURE

  market arriere-route

  !

  card crypto client cryptomap of authentication list drauthen

  card crypto isakmp authorization list drauthor cryptomap

  client configuration address card crypto cryptomap answer

  map cryptomap 65535-isakmp ipsec crypto dynamic dynmap

  !

  interface GigabitEthernet0/0

  NAT outside IP

  IP 1.2.3.4 255.255.255.240

  cryptomap card crypto

  !

  interface GigabitEthernet0/1

  IP 192.168.1.254 255.255.255.0

  IP nat inside

  !

  IP local pool dhcppool 192.168.2.50 192.168.2.100

  !

  Note access-list 198 * Split Tunnel encrypted traffic *.
  access-list 198 allow ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255

  !
  Note access-list 199 * NAT0 ACL *.
  access-list 199 deny ip 192.168.0.0 0.0.255.255 192.168.0.0 0.0.255.255
  access-list 199 permit ip 192.168.1.0 0.0.0.255 any

  !

  Sheep allowed 10 route map
  corresponds to the IP 199

  !
  IP nat inside source map route sheep interface GigabitEthernet0/0 overload

  !

  IP nat inside source static 192.168.1.1 1.2.3.5
  IP nat inside source static 192.168.1.2 1.2.3.6

  The problem seems to be that static NAT take your nat exemption.

  The solution would be:

  IP nat inside source static 192.168.1.1 1.2.3.5 sheep map route
  IP nat inside source static 192.168.1.2 1.2.3.6 sheep map route

  HTH

  Herbert

• problems to install labview on ubuntu 10.04

  Hello, I tried to install the student version Labview cd on my ubuntu system, but when I run the INSTALL script on the linux file I get the following error message: / LabviewCD/Linux/labview-2009/bin/rpmq: error while loading shared libraries: libbz2.so.1: cannot open shared object file: no such file or directory can someone help?

  OK, with the helpful message of crear_unifi in the other thread, I managed to install Labview on Ubuntu. Great work, problem solved.

• DLR Uplink and GSS internal transit same VXLAN cannot ping each other.

  Start with, I run NSX 6.2.2 firewall rules on 'allow all' to 'all' to 'all' "all protocols", in other words disabled...

  I have a VXLAN 5000 transit, with an uplink DLR interface attached to it, and an internal interface GSS in the appendix in which neither of the parties can ping to another. So for troubleshooting, I added 2 VM Windows attached to the same transit VXLAN 5000, a virtual machine is on ESXi host 1 and the other is on host ESXi 4. They can fine ping each other, and two virtual machines can ping both the uplink of DLR and internal interfaces of the GSS.

  This question has puzzled me because it makes no sense, why the DLR and the GSS cannot ping each other but 2 virtual machines that VXLAN can ping all adjacent devices. I can even put bridges on those virtual machines with a rule NAT on the GSS and those virtual machines can get internet through the GSS, but no matter what I try, the DLR cannot ping the GSS, and the GSS cannot ping DLR...

  I need to define a static route between the GSS DLR <>- but if I can't even answer ping interfaces I'm dead in the water.

  If I install virtual machines in a network LAN DLR interface such as WebApp and test for example database, I can ping throughout the DLR together until the IP DLR Uplink, but then he cannot ping the GSS internal.

  Does anyone have suggestions for troubleshooting? Test commands that I can run? I tried many things and then lots of websites with the troubleshooting steps. Everything seems fine, all green checks in the installation steps... All roads, MACs, ARP tables appear as expected when I run test on host computers commands and controllers. I don't know what is the cause except for a bug in the code...

  All ideas are welcome... Thank you

  UPDATE:

  Yes, so it has need of a static NAT rule on the GSS...

  In my environment, I added a SNAT rule on adapter: ESG_Uplink with 0.0.0.0/24 CBC-translation dst: 1.1.1.101 (my lab ESG IP Uplink).

  It works now... VM tenant box connected to WebApp portgroup (192.168.13.115) can now ping gateway DLR, through routing OSPF to the GSS and ping on physical bridge of...

  I learned a lot on this one... I'm not going to worry about why the static route, I tried first post didn't work, since I was the OSPF running instead (which is more appropriate for my laboratory for realistic scenario anyway), and the Foundation will now suffice to build the rest of this POC vRA / vRO lab...

  Thank you in any case, sometimes it's just nice to have someone to listen.

• I get this error message 'The URL is not valid and cannot be loaded' when I try to go to Firefox home. I uninstalled the modules, uninstaleed and reinstalled a new fresh firefox which did not help

  I get the following error message 'The URL is not valid and cannot be loaded' when I try to go to firefox home. I uninstalled modules, uninstalled Firefox and then install a new version. Still have the problem.
  Thanks for the help

  This problem may be caused by a corrupt installation of Visual C++ or incomplete (several versions can be installed-by-side; SxS) it lacks certain runtime components (redistributable Packages), which depends on Firefox (problem with an embedded manifest file that specifies a specific runtime version).

  You need to install the missing components (for example, Redistrbutable end 2005 ++).

  • https://www.Microsoft.com/download/en/details.aspx?ID=5638
  • [908165/questions/908165] The URL is not valid and cannot be loaded
  • bug 713167 - Microsoft.VC80.CRT SideBySide errors, browsercomps.dll

• Drive external HARD Toshiba PX1267E - 1 32 cannot be properly detected/installed

  Hi everyone, I need help.

  I have a Toshiba PX1267E - 1 32 external hard drive that I used on my PC under Windows XP. Yesterday, I bought a new laptop with Windows 7. When I plug the HD via USB, it is said that it cannot be properly detected/installed.
  It does not appear in 'my computer' and I really need to transfer a lot of data on my new laptop.

  I can do to make it work?

  Are there drivers for Windows 7? I can't find my original CD

  Any help is very appreciated. Thank you

  Hello

  Looks like a HARD drive contains a preinstalled software that is not compatible with Win 7.
  I'm not sure if this will help but try this:

  Connect your HDD to the other no Win 7 PC
  Select the CD drive with your browser (password)
  Run the ONSPCLCK.exe (or another exe file which controls and password.)
  Select 'Options '.
  Select "Disable security password"
  Enter your current password
  Unplug the HARD drive
  Connect the HARD drive to laptop with Win 7 OS.

  welcome them

• 9.30 NIDAQ drivers not install LabVIEW 2011 - example. Microsoft .com's in LabVIEW 2010 under vi.llb

  I just upgraded to LabVIEW 2011 without uninstalling LabVIEW 2010.  I downloaded the last set of drivers DAQmx 9.30.  I find that these drivers are installed in a DAQmx folder under the vi.llb of theLabVIEW 2010 and NOT in the vi.llb of LabVIEW 2011.  The DAQmx features do not appear on the menus and the existing instances are reported as 'cannot be compiled. How can I get the DAQmx functions to properly install LabVIEW 2011?

  You must DAQmx 9.4.

  9.4 DAQmx

• problem with MAX after installing LABVIEW 10

  Hello everyone, I have a serious problem I installed labview 10 yesterday on 2 laptops, one of them works perfectly, however, the other gave me a two erros

  1.http://digital.ni.com/public.nsf/allkb/6CA56E2DDBCCA06086257591006141EE

  2. http://digital.ni.com/public.nsf/allkb/F24AA9FB6A3A0E9D86257539006141BE

  I tried the solutions above in the link, but it was all futile. can someone please suggest me what would be the problem? I had already LV8.0 on the laptop which is the cause of the problem. I tried to re - install the disk driver given

  for me by NEITHER, but no luck.

  When I started the laptop for the 1st time, there was a mistake in saying DOS command prompt: DATABASE ERROR and I cancelled the error!

  In addition, Labview works fine, its only MAX who has problems. is there a way I can only MAX to uninstall and reinstall? Please help me...

  Thank you

  Sorry CrackJack

  Try this one http://digital.ni.com/public.nsf/allkb/86256F0E001DA9FF86256FFD005B827C?OpenDocument    

• Impossible to fully install LabVIEW 2010 on WinXP SP3

  Hello

  I tried many times today to install all OR Developer Suite 2010 helps install disks. I catalogged all items that not have installed. LV 2010 works but I don't know if everything works. Here are the elements and the order in which I wasn't able to install:

  'Crucial questions when National instruments drivers using Microsoft Visual Studio.NET 2010 resolved by NOR-PAL 2.6.5' - I have successfully installed this but the message still comes up and gives me a message "Are you sure you want to move forward", when I'm trying to keep the installation

  "NOR-USI 1.8.0" has not been installed. Error 1935

  Error "Runtime-NOR-LabVIEW engine Interop 2010" 1935

  "NEITHER AFW UI assembled" Error 1935

  "OR Measurement Studio 8.6 company for VS2005 Runtime" Error 1935

  "NEITHER AFW Channel Configuration Tool" Error 1935

  "NEITHER AFW assembled custom user interface" Error 1935

  "NI LabWindows/CVI 2009 Service Pack 1 Runtime Engine" - no error number

  No idea if I need these applications run LV 2010?

  Thank you.

  It seems that there is something strange going on with your .NET framework, which is the origin of this conflict of driver.  Try uninstalling your current .NET framework as well as LabVIEW (from Add/Remove Programs) and re-setup of the Microsoft .NET Framework page followed by a new installation of LabVIEW.

  A few other things to note:

  Make sure you have all of your anti-virus software / firewall disabled while trying to install LabVIEW.  We have seen this before due Setup error.

  Also, make sure that you install your drivers after installing LabVIEW.

• Windows 7 takes 15 min to start after installing Labview 2012

  Hello

  I need help on this, is this a bug?

  The problem is that on my laptop after installing Labview 2012, it takes about 15 minutes to start, this happens every time a restart or start my laptop.

  At first I thought something with my laptop, but then my colleague also installed Labview 2012 on his laptop and has exactly the same problem, the difference is that his new laptop and is running windows 7 Professional 64-bit, mine is older and is currently running windows 7 32-bit professional.

  I tried to disable the services NOR, but has not solved the problem, but when I disable all windows services that start at startup, the startup is fast.

  Also note that I had Labview 2011 installed before and I didn't have this problem before.

  Tried also to find something in the registry, but nothing.

  Any who have this problem, or a solution to this?

  Thanks in advance

  This problem seems to be resolved, but then he come back again a few days later

  I did many tests in my laptop and found it to be in the "Service of Network Store Interface" service (INS). Disabling this service, you have your problem solved, but there is another problem, you lose the network.
  This happens because the "DHCP Client" service depends on the national statistical institutes.

  Also, this issue seems to occur only when the PC is in a domain and I'm in a windows server (Windows SBS2008) domain.

  Then I found that if you set manual this services which depend on national institutes of statistics (DHCP Client, DNS Client, IP Helper, network connections, local awareness network) and also put INS manual
  You must also disable the "Workstation" service that also depends on national institutes of statistics (why turn off? Because there are 3 services that depend on the workstation service, they will require to start, and then it will force NSIS to start, then long boot, if you really need of the dependent services on workstation, do the same as for them)
  Not also need uncheck this services in msconfig window if they are checked, and then the PC will boot normally without a network.

  When you start, you should go to services and start the DHCP Client for the network (and the other if you really need)
  This will force also NSIS to start and other services that depend on the national statistical institutes.
  The first time the PC restarts, you may need to reset these services to manual in the services window, I had to do, and then in sebsequent boots, they have been already set to manual
  If you leave right on the dependent services in automatic or automatic (delayed start) it will force NSIS to run and start time will go to + - 15 min

  Because you must manually start "DHCP Client" for the network, here's a solution to do it automatically after have connected you:
  1 - Go to control panel, and then open administrative tools
  Task 2-open Scheduller
  3. on the right click "Creat fundamental task.
  4. in the first window give a name ("DHCP" for example) and press next
  5 - Click on "When I Logon" and press next
  6 - click on "Start a program", and then press next
  7. in the "program/script" insert: net
  8. in the "Arguments" insert: start "DHCP Client".
  9 - Press 'Finish' and you're done