My address bar disappeared but not the navigation bar?

Similar Questions

• Portege M400 connected to the WiFi router, but not the navigation of Web pages

  Hello

  I use M400 laptop computer series that I bought in 2005 and do not know if the guarantee was already finsihed, although I paid extra for an extended warranty.
  You should check a second time.

  My wireless connection was working fine with my conection DSL broadband 2 years ago, I was using router Netgear wireless. In the last 2 years that I did not use wirless conection, recently I bought Thomson TG585 router to my ADSL connection wireless broadband. This wireless router works fine with my other Mac desktop computer but my laptop is not browse a Web page if it says connected with WiFi router.

  I went through all the settings and even I have discussed this question with the technical team bradband and say there is problem with my computer laptop bcz Mac Desktop works fine.

  I checked in the wireless troubleshooting setting and still not able to solve this problem.
  I use KesperKey Internet Security and I tried to turn it off for the test connection wireless but always face same problem.

  I wonder if anyone can help me?

  Thank you.

  Hello

  Disable all the security settings on your router and then try to connect the M400 protected wireless.
  If you will be able to connect to the WLan and will be able to navigate a few s webpage you could activate step by step all the security settings such as encryption of WLan, Mac address filtering, SSID hidden, etc.

  By the way; Have you tried to update the driver WLan?

• I can access network, but not the internet.

  I am able to access my network but not the internet.  However, I can get on the internet if I use parallels.  Does anyone else have this problem? If so, how have you managed to solve.  I rebooted without parallels and nothing changes.  Any suggestions?

  In the menu bar, you select

   ▹ System Preferences... ▹ ▹ ▹ Advanced TCP/IP network

  What values are given for the following?

  Configure IPv4

  IPv4 address

  Subnet mask

  Router

• Wizard BootCamp 6.0.1 running on El Capitan 10.11.5 installs single partition BootCamp on the disc Fusion consisting of 128 SSD part G SSD and 3 TB of HARD drive on an iMac (retina 5K, 27 inches, end of 2014), but not the part of the HARD drive?

  How is it assistant BootCamp 6.0.1 running on El Capitan 10.11.5 installs single partition BootCamp on the disc Fusion consisting of 128 SSD part G SSD and 3 TB of HARD drive on an iMac (retina 5K, 27 inches, end of 2014), but not the part of the HARD drive?

  This has two questions:

  1 capacity of SSDS faster for Fusion drive has been reduced. Therefore less effective for the reader of the merger. For example if I need to create a partition of 80G for my windows bootcamp partition, only 48 G will be left in the drive of the merger.

  2. ability of the bootcamp windows partition becomes very limited, cannot be greater than 120 G.

  3. even when I try to fuse out of the drive of fusion in the 128 G SSD and 3 TB of HARD disk, and then run the BootCamp assistant to create the bootcamp partition start from scratch to reinstall El Capitan only on the HARD drive (without drive Fusion), it won't let me do anything, it just shows an error that says something like "a person has created additional partitions on this drive please select. another disc. But there is nothing else to choose.

  Before my (5 K, 27 inches, end of 2014 retina) to El Capitan Yosemite, I was able to use the previous version of the wizard BootCamp 5.x to create the partition, bootcamp on the drive of the merger. And it will be divided in the fuser unit in two and insert the Bootcamp partition (with the size I chose, which can go up to 1 TB) between two partitions of MAC OSX.

  The disk partitions resulting from it, will be the partition MAC OS x on the SSD, the partition MAC OS x on the HARD drive partition #1, partition MAC OS x on the HARD drive partition #3.

  Then there is the BootCamp partition on the HARD drive partition #2.

  Is there a way to get what I need?

  That is what has been described in this notice of two canoes?

  Installation of Windows on a Boot Camp partition on a drive of TB Fusion 3

  n-on-a-3-TB-fusion-drive http://twocanoes.com/Winclone/support/installing-Windows-on-a-Boot-Camp-partitio

  Thank you.

  After having worked on those weeks, I realized that I need very painfully (by first going back to Yosemite and bootcamp 5 to escape all the limitations of El Capitan and BootCamp 6) I want to share here. Someone at - it other smarter solutions welcome.

  Note these steps and mentioned drivers only work for my version of iMAC, retina 5K late 2014. If you have other material, please search on the web to see which driver will work first. And all of these steps are destructive and assumed that you first take backup. It is only shared for interest only. Readers will have to bear your own risk.

  A. take backup

  1. take a backup completes my iMac Fusion Drive using Time Machine. Then restart with a Yosemite USB installation and select Terminal from the menu on the top bar.

  B. fuse out of the merger in two physical disks drive: SSD + HDD

  1. in the terminal, type the commands in show what the logical volume group ID and the ID of the logical Volume of the disc fusion)

  Cs diskutil list

  2. in the terminal, type commands for the fuse of the fuser unit and separate them to an SSD and a HARD drive.  Note: All data will be destroyed in the drive of the merger. There are many articles in this community on how this could be done,

  diskutil cs deleteVolume Logical Volume ID

  CS diskutil remove logical Volume Group ID

  This should finish within 30 minutes. If you have taken more time, this means that your reader of fusion has been altered somehow.

  I hit this issue too.  To use this command to remove the fusion drive hung up, and I need to do the hard to scramble a few sections of data in the hard disk partition table using the controls to tell the OSX this hard drive is a new without partitions:

  Cat >/dev/random /dev/disk0 (where/dev/disk0 is the SSD)

  and repeat for disk1/dev/disk1 which is the HARD drive in my case).

  This command will not return anything, but expect to press Ctrl-Z to end after 1 minute.

  2 create independent partitions (non-fusionend) for the installation of OSX.

  Borne Terminal output, and select disk utility, in disk utility, select the drive to HARD disk (and not on the partition), you will see the error message and you will be asked if you want to fix the fuser unit, click on ignore. Then wipe the HARD drive to create a single 'extended OSX journaled"named"HARD drive".

  3. Repeat step 2, and then erase the SSD drive to create a single 'extended OSX journaled"named"SSD ".

  C. install on the HARD disk as drive didier autonomous not fusion.

  1. go to Yosemite install screen and proceed with the installation of a clean copy of Yosemite to the iMAC. then connect you.

  D. use BootCamp Yosemite f5 to install windows.

  1. launch Yosemite bootcamp.

  2. check the two checkboxes for creating the USB drive to install windows 7 or a later version, and to download the windows supports the Apple software.  Do not click on the last box to install or remove windows pie creating real bootcamp partition again.

  3. it may take several hours to complete this function of your internet b/w and also performance of your USB drive.

  4. If you install Windows 7 (like me), then the downloaded drivers will not work for you, this will cause the issue of the device driver appleDSS.sys does not like this driver and others are too recent for windows 7 to use.  Also, your keyboard and mouse may not work even if you try to plug in a USB external keyboard or a mouse. You need to replace the drivers downloaded by others (the Boot Camp 5.1.5769 drivers that I find in this link: Software Support of Boot Camp 5.1.5769.) (Note: this driver is material specific only works for my iMAC model).  Once you have downloaded it, copy the two files in the root directory of the USB installation to replace the original ones. It's specific and material available for download somewhere on the Apple Site.

  -From the Finder, delete the $WinPE$ and the Boot Camp of the FLASH PLAYER files.

  -Expand the old drivers for Boot Camp 5.1.5769 (two records and another file) on your desktop.

  -Copy the $WinPE$ and records of Boot Camp in the FLASH PLAYER.

  5. open Boot Camp Assistant again and only select the third option, install Windows 7.

  It will show you the screen to select what installation disk, select HARD drive.

  Then drag the slide bar to select the size of the Bootcamp partition for windows you want, knowing that there is a restriction for windows installed using training camp on a MAC that the last byte of the BootCamp partition must reside in the first byte of the 2.2 T of each physical hard drive.

  For my case, I need only 500G for bootcamp and leaving behind 1.7 to for my MAC OSX partition immediately after the bootcamp partition and an another 0.8 T MAC OSX partition after him. 1.7 TB and the partition of MAC OS x 0.8 TB well exploited in the meantime bootcamp partition, will be merged into a fusion drive by Bootcamp. Thus, you will end up with total 2.5 TB of disk space in a logical drive - fuser.

  Go to this link for more details on this subject: n-on-a-3-tb-fusion-drive http://twocanoes.com/winclone/support/installing-windows-on-a-boot-camp-partitio

  6. continue the process to partition the hard drive, then it will restart automatically in windows installation mode, install windows.

  7. once the installation is complete, check that windows is functioning correctly.

  E. Si you want to upgrade to windows 10 Windows 7.

  1 if you plan to upgrade to windows 10, you'll find that the windows IE v.8 7 is no longer works and had many problems to load the page.  Then when you try to download the latest version of Internet Explorer, you get an error that you need at least windows 7 SP1 to support the last IE.  Life is too complicated, just download the google Chrome browser, then search for download windows 10 and then run the Microsoft valuation tool to upgrade.

  2 but before upgrade you, unplug all your MAC USB drives, otherwise, you will find that, after having spent an hour downloading the windows 10 software, the upgrade will fail with the error "/ dynamicupdate...» ». It is an inexplicable mistake that no one seems to understand why. There are articles with proven results that the removal of all USB drives before running the windows 10 upgrade tool will correct this problem.

  F. reinstall OSX El Capitan

  Once your target windows system (if windows 7, windows 8 or windows 10) works very well.  You can continue to create again your Fusion drive and reinstall OSX El Capitan.

  1. Insert the install of OSX Yosemite rear USB to the iMAC, and then select Restart Windows, or stop, and then turn the MAC once again.

  2. When you hear the ringing tone, press on and hold down the option key for 10 seconds. Then you release.

  3. on the selection screen, select start Yosemite OSX install drive.

  4. after starting, do not proceed to install OSX El Capitan again. But select Terminal from the menu bar.

  5. in the terminal, type the command 'diskutil list cs' and you should see nothing to prove that there are no existing fusion drive yet.

  6 type the 'diskutil list' command to list all disks and partitions.

  The SSD has two partitions, the/dev/disk0s1 of EFI (209 MB) partition and the other/dev/disk0s2 of OSX partition we created in step B above, called SSD around 121 G.

  The HARD drive has two partitions, the/dev/disk1s1 of EFI (209 MB) partition and the other/dev/disk1s2 of OSX partition we created in step B above, called SSD.

  G. delete the logical storage of nucleus on the HARD disk drive and it refuses with the DSS to form a merger with faster performance disc

  1. Insert the install of OSX El Capitan rear USB to the iMAC, and then select Restart Windows, or stop, and then turn the MAC once again.

  2. When you hear the ringing tone, press on and hold down the option key for 10 seconds. Then you release.

  3. on the selection screen, select start Yosemite OSX install drive.

  4. after starting, do not proceed to install OSX El Capitan again. But select Terminal from the menu bar.

  5. in the terminal, type orders for (to show what are the logical volume group ID and the ID of the logical Volume of the logical drive). You should see the logical volume to basic storage group created using two partitions on the hard drive, 1.7 TB and TB 0.8 created when we run the Yosemite Bootcamp to install windows.

  Cs diskutil list

  6. in the terminal, type commands to delete logical drives from basic storage.  Note: All data will be destroyed in the logical drive.

  diskutil cs deleteVolume Logical Volume ID

  CS diskutil remove logical Volume Group ID

  7. tap "diskutil list" command lists all the resulting partitions. You should see that the HARD drive has the following partitions.

  / dev/disk0 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * GB 121,3 disk0

  1: disk0s1 EFI EFI 209.7 MB

  2: Apple_HFS GB SSD 121.0 disk0s2

  / dev/disk1 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * 3.0 to disk1

  1: EFI EFI 209.7 MB disk1s1

  2: Apple_HFS 1.7 Untitled TB disk1s2

  3: disk1s3 Apple_Boot Recovery 650.0 MB HD

  4: Microsoft database BOOTCAMP 503.0 GB disk1s4

  5: Apple_HFS 801,4 Untitled GB disk1s5

  8 type the following commands to create the logical volumes group, named "myLVG" (or the name) of fuser using the usable for OSX to the SSD and HDD partitions.

  diskutil cs to create "myLVG" disk0s2 disk1s2 disk1s5

  Note: Mark the group id of logical volume shown in the results.

  In my case, I want to book the last partition as standalone partition disk1s5 no-fusionend, so I can use it to raise the back, or format it in FAT32 to allow the exchange of data between the MAC and boot camp.

  So, I do not understand this last partition in the drive of the merger. in my case, the command that I used is: diskutil cs to create "myLVG" disk0s2 disk1s2

  9 create logical volumes named "Macintosh HD" (or you call it) on the logical volume group we just created for the reader of the merger.

  diskutil createvolume logical volume group ID jhfs cs + 'Macintosh HD' 100%

  10 command "diskutil cs type list" to check the resulting fusion drive created.

  CoreStorage groups of logical volumes (1 found)

  |

  + Logical Volume - Group F53C7A25-C2F3-4997-91E9-2E6B6BAB2E0E

  =========================================================

  Name: LVG

  Status: online

  Dimensions: 1815635525632 B (1.8 to)

  Free space: 90112 B (90.1 KB)

  |

  +-Physical volume E176873C-7C80-4759-8110-BA7307E0C4B3

  |   ----------------------------------------------------

  |   Index: 0

  |   Disc: disk0s2

  |   Status: online

  |   Dimensions: 120988852224 B (121.0 GB)

  |

  +-Physical volume 6535AC3C-DCF8-453F-AD47-98905538386E

  |   ----------------------------------------------------

  |   Index: 1

  |   Disc: disk1s2

  |   Status: online

  |   Dimensions: 1694646673408 B (1.7 to)

  |

  +--> Logical volume family F3D15F87-FB84-4B43-B2F2-E9EACC7C42D9

  ----------------------------------------------------------

  Encryption type: no

  |

  +--> Logical volume 0D807F6E-FB7C-418F-AAF4-EF3EA3525D10

  ---------------------------------------------------

  Disc: disk2

  Status: online

  Size (Total): 1809780178944 B (1.8 to)

  Reversible: no

  Name: Macintosh HD

  Volume name: Macintosh HD

  Content indicator: Apple_HFS

  LVG Type: Fusion, sparse

  11 exit the terminal, go back to OSX El Capitan install screen and select the name of the fuser unit 'Macintosh HD' proceed to begin the installation of the os x for installation.

  12. There will be a step in the installation ask you if you want to configure as a new computer, or restore from a time machine previous backup. Make your own choices it accordingly.

  13 once OSX El Capitan has been installed and you have finished restoring the data and custom configurations, you can enter the application of preferences to check if you see the icon of the "Startup" disk", and if you choose Startup BootCamp in the next reboot, you should be able to boot up to Windows without pressing and holding the button option when reboot and choose to start windows manually. Also, in windows, you should be able to click on the bootcamp Control Panel and select for a startup to OSX on the next reboot.

  14. one thing to be aware, if you install bootcamp in this way, the boot camp and the GUI utility disk in OSX El Capitan will not be able to adjust your settings. This means, if you need to touch anything or to readjust the size of the partition, you will need to do it again in step A. Alternatively, some how to get started with installing Mac OSX Yosemite USB, then adjust the partitions using similar commands shown in this article or other articles in this community.

  15. yet once please take personal responsibility on damage if you follow the instructions in this article.

• I can't get on my xbox account, I have email but not the password

  I can't on my xbox account, I have email but not the password, but that e-mail address is not locked on me trying to get up that I need to get on this account that soon ASP.

  Hello

  I suggest you to please follow the steps in the below link and check if that helps.

  http://support.Xbox.com/en-us/billing-and-subscriptions/Windows-Live-ID/Xbox-Live-sign-in

  http://support.Xbox.com/en-us/billing-and-subscriptions/account-management/manage-Live-ID

  If the problem is not resolved, I suggest you please contact XBOX support for help.

  http://support.Xbox.com/en-us/contact-us?NavigationPath=/en-us/billing-and-subscriptions/account-security/password-protect-account

  I hope that helps!

• When searching in Windows 7, I get a list of headers group for items, but not the articles themselves

  Hello

  When I click on start and enter text in the search programs and files text box, the search returns only for the items returned, but not the articles themselves group headers. Can someone help me solve this problem?

  Thank you

  Christi

  You can get a fix taken care that addresses this problem and it should prevent from happening again in the future. To get it, point your browser to the following Web site:
  http://support.Microsoft.com/kb/977380
  Click then on "view and request the hotfix downloads" which is located just above the beginning of the knowledge base article.

  Hope this helps,

  Alexander Sklar
  Windows engineering - sustaining user experience / developer experience team
     http://blogs.msdn.com/Asklar

  This posting is provided "AS IS" without any warranty and not an entitlement.

• addressable PDF selected but not produced on 6600

  addressable PDF selected but not produced on 6600

  Thanks again for the help.  But I finally solved the problem myself by downloading a program called 'HPPSDr.exe' HP and running.  The searchable .pdf function now works very well on my HP Officejet 6600 device.

• HP Photosmart 6510 series connects to the network and Internet, but not the computer.

  Hey all,.

  I have a desktop H8-1228 and 6510 e - printer.  I got both products at the same time.  I did the initial installation, and everything worked perfectly.  I was able to print of my HP Touchpad (the printer was on the floor and my Touchpad was down.).  Recently, I made a trip for two weeks.  I turned off the printer.  This seems to have been a mistake.  Now, he will only contact my network and Internet, but not the computer.  The Setup program keeps telling me that it is 'Impossible to find the printer' and that he wants me to check the IP address of the printer.  I did this many times by printing the HP's Configuration Page from the printer screen.  I also used Windows "Add a printer" without success.

  I have installed and uninstalled the software several times; every time that remove the icon of the printer and the Standard TCP/IP port in the "Devices and printers" section in Control Panel.  A few minutes earlier, I used Regedit to delete any reference to the series of HP Photosmart 6510 in the registry, believing that it could help my situation.  There can be no. :-(  I did the installation with the same problems that I had all the other times that I tried to install it.

  No help from you the printer experts will be greatly appreciated.  I'm not a novice as you can see.  This situation, however, launched my posterior. :-))

  Hi old_geekster,

  You may want to enable disable all startup programs in msconfig until you are able to access the Web integrated printer server. It seems that there is something in the communication with the printer's operating system blocking. It will most likely software firewall or security related.

  HP has designed a quick and easy tool that diagnoses and solves many problems of printing, scanning and connectivity: The HP Print and Scan doctor. HP recommend you to download and install Print and scan doctor no matter what time you need to solve a problem with your HP printer from the link below.

  I would like to know what are the errors you receive?

  http://www.HP.com/go/tools

• How just the keywords in a folder to display name, but not the keyword of the same name, itself?

  In my keyword hierarchy, I, for example, special types of photography.  It is a folder called "photography."  Below I have landscape, portrait, seascape, Candide etc...  How can I get just the keywords within the photograph on the screen, but not the word "photography" itself?

  How can I get just the keywords within the photograph on the screen, but not the word "photography" itself?

  Do you mean, how do you get pictures containing child 'photography' to display keywords, but not the photos containing the keyword "photography"?  If that's what you want:

  In the library filter bar metadata Explorer, add the keyword column.  Expand the parent keyword "photography".  Click on the first keyword of the child and shift + click on the key word of the last child, so that all the keywords under "photography" are selected.  All the photos containing the child keywords of "photography" show now, but no photos containing "photography":

  

• How can I transfer photos from my iPod touch 6th generation for my macbook pro WITHOUT using iCloud, please? It's simple with another camera but not the case, it seems, for the Apple iPod

  How can I transfer photos from my iPod touch 6th generation for my macbook pro WITHOUT using iCloud, please? It's simple with another camera but not the case, it seems, for the iPod Touch from Apple.

  Use import option from your Mac:

  Import photos and videos from your iPhone, iPad or iPod touch - Apple Support

• My Nano Gen 7 is recognized on a single computer, but not the other

  My Nano Gen 7 is recognized on a single computer, but not the other.  I went through all the troubleshooting tips.  Different cables, try all USB ports, uninstall/reinstall itunes, etc.  I have itunes more up-to-date software.  I was able to connect the ipod to my backup computer and confirmed that I also have the software more up-to-date on the ipod.  Since I am able to connect to it, I also did a factory reset the iPod, but it still wouldn't connect to my main computer.  Nothing has worked.  I think there must be a setting on my pc.  I use the latest version of windows 10.  Any suggestions are welcome.  Thank you

  I just bought an Ipod Nano 7th generation and itunes does not recognize it.  Had by all the standard troubleshooting (uninstall/install itunes, etc.) and no luck.  My PC recognizes, he calls the 'nano' but acknowledges as a USB mass storage device.  I spoke to a support person from apple for more than an hour to help me troubleshoot it, finally they just said it was a windows problem, and I need to contact Microsoft.

• Apple Watch: can I receive all messages from whatsapp on my Apple Watch, but not the Group whatsapp messages, don't know why... Help, please. Besides, my watch is custom in Spanish, but only answer messages Whatsapp understands English... someone kn

  I can receive all messages from whatsapp on my Apple Watch, but not the Group whatsapp messages, don't know why... Help, please.

  Besides, my watch is custom in Spanish, but only answer messages Whatsapp understands English... anyone know why? Thanks to you all!

  Hello

  To change the language for a response on your watch: Press answer > firmly press the screen > press on choose language > select Spanish.

• F & G Committee < ' F & G Committee' > is not a valid e-mail address because it is not the form user@host. You need to correct before sending the e-mail message.

  Out with the new v.31.1.0, the: 2 September 2014 version of Thunderbird, I can email is no longer a list of recipients, getting the error msg: F & G Committee < ' F & G Committee' > is not a valid e-mail address because it is not the form user@host. You need to correct before sending the e-mail message. In earlier versions, the addresses of individual e-mail in the list (F & G Committee in this case) are automatically placed in as the e-mail is sent. Is there a solution to this problem?

  Read this.
  https://support.Mozilla.org/en-us/questions/1019019

• Why is-game of Thrones season 6 available in the iTunes Store Germany but not the UK store?

  Why is-game of Thrones season 6 available in the iTunes Store Germany but not the UK store?

  I don't think that we left the EU again!

  Likely UK rights holder has failed to Apple a license to sell here - you should ask them if/when they have planned to do.

• Firefox 14.0.1 shows is no longer the Norton SAfe Web icon in the seacch results. The toolbar is there but NOT the icon of web security next to the URL in the search results

  After updating to Firefox 14.0.1 my results search no longer show the icon of Norton WEB security beside each result. It worked fine before the upgrade. The Norton toolbar is there, and when you click on the site that the web report secure is there but NOT the icon in the search results.

  Norton has released updates for Firefox 14 morning even as the version of Firefox 14. Norton releases usually updates, the morning even as the new versions of Firefox. Have you updated Norton through their LiveUpdate?

  • See-> https://community.norton.com/t5/Norton-Toolbar-Norton-Identity/Firefox-14-Support-for-Norton-Toolbar/m-p/760924

  If this answer solved your problem, please click 'Solved It' next to this response when connected to the forum.