My player will not recognize a drive Optiarc DVD RW AD - 7203 A ATA Device

Similar Questions

• Lenovo Y430 - drive Optiarc DVD RW AD - 7640 S ATA Device dvd does not

  Hi guys,.

  My Lenovo Y430 - drive Optiarc DVD RW AD - 7640 S ATA Device dvd does not

  Its not reading any cds/DVDs.

  Please could you help me how to fix it

  Once am put any DVD that the DVD is flashing and after a few seconds, his flashing no more.

  Mine is under WIndows Vista SP2

  I checked the CD-ROM/dvd-rom drivers in its 'active' display ' device working properly "Device Manager and registry also to 'upperclass' or 'lowerclass' settings entry just good.

  Please someone help me how to solve this problem.

  Thanks in advance.

  Kind regards

  Rambeau

  ++

  @bjawasa is 90% out of material. Lenovo ask to change your dvd - rom with a new free of charge if you have the warranty.

  You can call the help line: hindi or English speaking - 1800-3070-0010 (Toll-free) or 1800-113-324 (Toll-free)

• Cannot load programs: _ Optiarc DVD RW AD - 7203 A ATA Device.

  Tried to load a program.  Is not loaded, run from Diagnostic report, said the device unusable material.  Such failure using the VxD (code 19) charger.  A run Device Manager. I received the message: "Windows cannot start this hardware device because its information configeration (in the registry) is incomplete or damaged (code 19).»
  I loaded the program in the past, no problem. I saw a similar problem of Nikki, but with a problem of 'code '. 10  The very complicated enjoy solution so didn't do.
  I also have Windows Vista Home Premium, Copyright 2007, Service Pack 2 system Type 32.
  I tried uninstalling the driver where it said to uninstall in Device Manager.  Rebooted and tried to get the system to find the driver and then reinstall but it just says my driver was updated and did nothing.

  Help!

  Texas Rose

  Hello

  19 code means there is a driver conflict such as two devices attempt to use the same resources.

  Please make all below even if you have done some before as it is often the set of operations which solves
  the question.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.

  Normally the above will solve this problem otherwise working your way down through them, even if you did
  them before.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  Hope these helps.
  Rob - bicycle - Mark Twain said it is good.

• Software peripheral drive not properly installed - Code 39 - Optiarc DVD +-RW AD 7580 A ATA Device

  Need help!
  Recently bought a laptop Dell Inspiron 1525 using the Vista operating system.
  The DVD + RW device worked but recently failed.
  Device Manager found the driver who is Optiarc DVD +-RW AD 7580 A ATA Device
  Device Manager is a (-) marker that tells me that the driver does not work.
  I tried to update the driver but the message received is "already installed the latest driver.
  I wanted to uninstall driver and rebooted the system.
  On reboot, the system attempted to reinstall the driver for my CD ROM
  I then received message 'disk device software was not successfully installed ".
  Also received message "Windows cannot load the device of this material. Code 39 "
  At the present time, my CD-ROM device does not work.
  I would appreciate anyone who has a solution to this problem.
  Thank you in advance.

  Have you recently installed a new burner software? Several of installs it burner can cause error 39. You can rightclick this link to another thread of responses on the deletion entries "Upper filters" and 'down '. You can remove those creating the CMD file I'll paste it in below, created by William Keener.

  1. Copy carefully and then paste the following three commands in Notepad:

  Reg export HKLM\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}-%userprofile%\desktop\CDFiltersBackup.reg
  reg delete HKLM\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}------UpperFilters f v
  reg delete HKLM\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}------LowerFilters f v

  1. Save the file to your desktop as DeleteCDFilters.cmd.
  2. Right click on the DeleteCDFilters.cmd file to your desktop, and then click run as administrator.

  Note After running this script, all custom CD/DVD filter drivers installed programs maybe isn't able to use your CD/DVD until your reinstall these programs. If the script command solves the problem, you can restore your custom filter of CD/DVD drivers by double-clicking on the CDFiltersBackup.reg that the command script exports to your desktop.

  
  (Soon we will see a button "FixIt4Me" of his team to do this automatically.)

  Mark L. Ferguson MS - MVP

• Optiarc dvd rw ad 7280 s ata device has a driver problem

  "" How can I solve this problem of pilot-"optiarc dvd rw ad 7280 s ata device has a driver problem" and error 19

  I am using windows 7 Home Edition

  The does'nt of the computer recognizes the optical device

  How can I SOLVE this

  E-mail address is removed from the privacy *.

  Thank you

  Hello.

  -Run these attach the.

  http://support.Microsoft.com/kb/316529/

  http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

  http://support.Microsoft.com/kb/982116

• DVD/CD RW optiarc dvd rw ad-7560 s ata device suddenly stopped working I get a "code 10 this device cannot start.

  My CD/DVD RW optiarc dvd rw ad-7560 s ata device suddenly stopped working I get a "code 10 this device cannot start.  I have uninstalled and still get this error.  When I put a CD in nothing happens.  It is not read.  Any suggestions?

  Hello

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers
  http://support.Microsoft.com/kb/943104/

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Optiarc DVD RW AD - 7640 A ATA DEVICE

  I am able to read the CD in my DVD RW drive, but not a DVD.

  Earlier, it was working fine.

  Don't know since when it has stopped working.

  I have 'Optiarc DVD RW AD - 7640 A ATA DEVICE'

  Details of the machine: Lenovo 3000 Y410 7757 88Q with windows Vista Home Basic.

  Hello Manu Mali,

  Well, I would replace the drive with a new one. NewEgg.com is a great place to watch here: http://www.newegg.com/Store/SubCategory.aspx?SubCategory=5&name=CD-DVD-Burners I recommend the Pioneer players. They are expensive these days. Hope this helps you. Let us know anyway. Make it a great day!

  "In the end the love you take is equal to The Love You Make" (The Beatles last song from their latest album, Abbey Road.)

• Windows 8 will not recognize discs in my dvd, DVD or CD player?

  I've upgraded to Vista to 8.  Windows * does not recognize the discs loaded in the dvd player.  Computer, you can see the drive but it won't read the disc in the drive.  I tried to update the drivers, 8 says that they are up-to-date.  I have run the Diagnostics Dell, said that my computer works well.  Have uninstalled and reinstalled the drivers for the dvd drive, no change.

  I installed windows media center, without change.  Do I have to install a soft DVD and which?

  This has been the most frustrating windows upgrade of my life

  Hello

  Readers appear in the computer?

• Philips +/-RW DVD8631 will not recognize the drive

  Hello
  My computer specs are:
  Dell Dimension 8300. Multiprocessor PC ACPI. Intel Pentium 4 CPU 3.20 GHz 2 x Radeon X 300 series. ATA Storage Controller - 266F, Intel 82801FR SATA AHCI Controller, Intel 82801FB/FBM.

  My problem is that I filled my disk space and would like to burn files to CD - R or DVD-R for free space. I select the files I want to burn and ' move to ' the drive can burn data (Philips +/-RW DVD 8631). When I click on "Write these files to CD" it opens the Assistant when you type the name of the disk. I type the name and click "next". Then, I get a message that tells me that there is no disc in the drive. I used the software 'Identifier of DVD' which was recommended on the forums before, and it does not recognize the disc in the drive. I use DVD + R 8 x produced by "imation".

  If there is someone who can help, I'd be very happy. Thanks in advance to those that do.

  Thank you
  Ryujin

  Message edited by Ryujin9891 on 10/03/2008 19:35
  
  

• driver problem Optiarc dvd rw ad - 7561 s ata device

  Dear Sir.
  Recently, I buy a compaq presario CQ61-115EE before Laptop.Twodays I was watching the movie by the player. After that, I loaded panasonoic camera digital cd software tried to install in my laptop, because installed everything except fast player and at that moment, I uninstalled all programs related to the software of panasonic. On this day evenining I'm watching the movie again via a system drive, but is not running. So I went to the cotrolpanel Device Manager. In that I crossed optiac dvd rw file and observed in driver Panel. In this appearance, Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available. And I tried to update via internet but showing only already updated file is in the laptop.

  My LAPTOP is compaq presario CQ61-115EE with windows vista Home premium service Pack 2.
  Optiarc DVD RW AD-7561 ATA Device

  Please help me solve this problem.
  Thank you

  vsrao
  Engineer (execution of piping)
  Muscat

  Muscat vsrao

  Hello Valerio srinivasa rao,

  Have you tried to uninstall your optical drive through the Device Manager and restart your computer? If this isn't the case, you should do it.  Otherwise, have you tried this miracle solution?

  Link: http://support.microsoft.com/kb/314060. You need to uninstall all third-party software (example: Roxio, Nero, or iTunes) from your computer

  prior to this fix. After you restart, you can reinstall your software and try again to see if that solves your problem. Otherwise, it could be that the drive is dusty

  (goal) or bad. Hope this helps you. Let us know anyway. Make it a great day!

  "In the end the love you take is equal to The Love You Make" (The Beatles last song from their latest album, Abbey Road.)

• Optiarc DVD RW AD-7580 s ATA Device. My DVD wont overprinting no matter what media, CDs or DVDs!

  People of the night

  IV brought my laptop second hand. Today I went to start to move my music collection on my laptop, unfortunately my DVD player doesn't want to overlay my CD or DVD even.

  IV read if some threads here and followed some advice. IV reinstall the drive, no luck. I tried to change the registry, but when I got to the correct file, there is no upperfilters or lowerfilters. I confused and stuck, any help will be most apprecited.

  See you soon

  James

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Optiarc dvd rw ad - 7561 has ata device

  My optiarc dvd drive does not work with dvd + R DL. Is this normal?

  ostlokla1

  Hello

  It should work with both + and - R discs.

  It's the version of HP of its description:

  Original HP AD - 7561a Support LightScribe technology 8 X DVD +/-R/RW/RAM DL writer

  =======================================================

  You have disk problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burn
  and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Burning at low speed, or by using the master could help. Maybe a CD/DVD cleaner
  Help.

  CD have a tolerance + - and you can write on the edge outside their tolerance. They
  may be released but it is usually more economical to replace the disk.

  Several good info here:
  http://Club.myce.com/

  Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
  http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014

  --------------------------------------

  To solve the problems:

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Gateway M series Optiarc DVD RW AD-7640 has ATA Device read any CD/DVD

  I have a gateway M series, and my dvd rw optiarc dvd rw ad-7640a ata would not read any cd or dvd, pls help!

  http://support.Microsoft.com/kb/982116/en-AU

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  See if the information above solves the problem.

  See you soon.

  Mick Murphy - Microsoft partner

• Optiarc DVD RW AD - 7910 has ATA Device

  Hello
  I have an Optiarc DVD RW AD - 7910A ATA Device. last week my laptop stopped recognizing it & after running the fix auto program it did nothing... can someone please help me?

  I use a laptop Lenovo T61

  Windows 7 Ultimate (X 32).

  Thank you

  ·                        http://support.Microsoft.com/kb/982116/en-AU

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  See if the information above solves the problem.

  For any question on Windows 7:

  http://social.answers.Microsoft.com/forums/en-us/category/Windows7

  Link above is Windows 7 Forum for questions on Windows 7.

  Windows 7 questions should be directed to / stationed there.

  You are in the Vista Forums.

  See you soon.

  Mick Murphy - Microsoft partner

• Qosmio G30-163: HD-DVD player will not recognize the Matrix Trilogy

  It is the last issue. WinDVD HD crashes after playing the opening for Blood Diamond and The Island WB logo. I posted a message about it, but it disappeared.

  Anyone know when the last update is due? He has not been one since December 26.

  Thks

  This post initially you're talking about? :
  http://forums.computers.Toshiba-Europe.com/forums//message.jspa?MessageID=95884#95884

  I have checked the European driver of Toshiba page and chose the Qosmio G30 PGQ31E series and found the update to the most recent Firmware for HD DVD-R + r DL DRIVE (SD-L902A) and for the readers of disc-DVD-HD TS - L802A.
  There are two different firmware updates.

  In addition, I would recommend looking for an update of the HD DVD player. It of necessary.

  Toshiab HD DVD player update was published on the Toshiab driver page. Update!