myDAQ Strip connector

Similar Questions

• Where to buy 20 PCB connector for myDAQ?

  Any person manufactures BOARD connectors, which corresponds to the myDAQ?

  Hi all

  To return to the subject.

  When you search for this information?

  https://decibel.NI.com/content/docs/doc-15087

• xw9400: xw9400. Pinout of the need for the connectors of the case (no psu connectors, only those in the case)

  I need the list of pins for various connectors case-Strip pin, especially J24 but other multispindle those too.

  Manual of Tyan S2915 Board for is a different version than that of poor quality that they OEM would be at HP for the 9400 and HP Tech Ref for the 9400 only provides pinouts for connectors well defined including pinout lie anywhere.

  The connector of the Panel before xw9400 J34 (there is no J24) pinout, the mother, is map:

  

  There are 2 key positions (lack of spindle) on pins 10 and 15.  Use these empty pins to help identify the signals.

  The pinout is very similar to other former workstations HP.  A few tips:

  -Pins 1 and 3 are for the harddrive activity led.

  -Terminals 2 and 4 are for the power light.  HP systems have back to back LED connected between these pins.  A green is on and functioning normal and red lights (and flashes error codes) when there are errors.

  -Connect a momentary between pins 5 and 6 switch will turn on the computer and off.

  -Connection of a momemtary between pins 7 and 8 switch will force a system reset.

  -PIN 9 is designated as + 5V, but it is powered by a 100 ohm pullup resistor to + 5V, so it will not provide a lot of power.  FOR INFO.

  -SPKR + and SPKR - are for the internal speaker.

  Most of the other connectors xw9400 follow standards of industry, i.e. the IDE drive and floppy connectors.

  Is there anything else you want to know?

• mydaq with bench hand vernier

  Hi, I write a project with my friend in a course based on the labview software and our project area is of biosensors. We have received a Vernier hand dynamometer to be the sensor of our project and need to write 'everything' to use and display any type of results (the interface so that it connects with the pc is NEITHER-myDAQ). one of our problems is that we are unable to find the right way to connect it to the device of myDAQ (there is a description of broaching on the vernier site but it's only for the plug itself and not the actual sensor). We do not know which wires are active, which is the constants of conversion of the output of the sensors etc., anyone who has experience with this or something similar and maybe can offer help (even a place where to look for this information), would be greatly appreciated. I tried searching the forums with as few keywords that I could come up with (something like 'hand dynamometer mydaq'), but nothing gave no results, I'm afraid... Thank you very much in advance. I post the links to the bench of the hand and the connector that we were given. http://www.Vernier.com/products/sensors/HD-BTA/ http://www.Vernier.com/Products/Accessories/BTA-ELV/

  Hello abenigma,

  I'm not very familiar with the sensor of dynamometer hand vernier, but if it uses the same analog connector Proto connection should look like this:

  Connect the following pins for wire connector:

  1. AI0 + SIG1 analog connector Proto Board

  2. + 5V power supply DC to 5V analog Proto card connector

  3. Power supply to the GROUND to GND of the analog Proto board connector

  4. AI0 - GND of the analog connector Proto Board

     Give it a try.

     ~ Sandra

• TX2-1020ea computer laptop connector ZIF - how it opened?

  Hello
  I have a HP Touchsmart TX2 1020ea laptop which is currently in pieces. I got everything that have stripped down as directed by the HP maintenance manual but am able with a ZIF connector that connects the audio panel with headphone and microphone to the motherboard plugs. HP refer to it as a ZIF but is not like the traditional type with the bar based on the cable. All other ZIF from PC connectors have opened without problem. I have problems with that different is that in addition to the cable in the connector, there is also a plastic label that comes out. There is no easily identifiable moving parts to the ZIF. Now, tempting as is to use the tab plastic as a grip just to pull on the cable, I also need to be able to reintegrate them when the whole PC.

  If anyone knows how this particular ZIF works please? Some pictures are attached.

  Thank you.

  Quite. PC fixed and set backs.

  Thanks for your help.

• HP Pavilion H8 - 1160t Strip annoying red light on front panel, how to disable?

  I bought a new HP Pavilion H8 - 1160t with this red light strip boring on the front panel.  How can I disable this light permanently? Thanks in advance.

  Follow the steps in thislink to remove the front cover and power button/light. Skip step 6 (detach the power switch on the motherboard connector) and focus on step 7 (connector to detach the LED on the motherboard). skip the remaining steps. Reinstall all parts except the LED Strip by reversing the above steps. That should do it.

  Frank

• Is anyone elses iPhone on iOS 10 or above show grey stripes and white when you try to restart the appliance just before it stops?

  I restared my Iphone 7 more because I tried to update 10.0.2 and just before it turned off my entire screen turned stripes gray and white goes horzitonally on the screen then powered back and its been working fine since. I tried this on an Iphone 6s and he did the same so, the iPhone was in version 10.0.2. Can someone tell me if this has happened to you? Try to restart your phone to see if it happens. If you have an iPhone 7, you must hold down the power button and the volume at the same time as the home button is virtual now.

  This happened to me on my Mini 4 and my iPhone 6. Both of them work fine, but I noticed the same problem that you have indeed. Must be a bug in iOS 10.

• Problem with smart connector

  Hi all

  I use my iPad Pro for a while now with the smart connector. Today, however, I noticed that the Smart keyboard did not respond to my entry and I kept getting the error message "This accessory is not supported by this device."

  When took a glance t the smart connector on my iPad I noticed some discoloration, almost as if it was burned. Can someone please help me understand how or why this might have happened? He never fell into the water or something else besides.

  Ill put a picture below. Thanks in advance.

  

  Hello. When electrical contacts carry the current, they may collect certain chemicals from the atmosphere. This does not mean that your air is bad, it happens everywhere. Try to clean the contacts gently. Be sure to check each on the keyboard too.

• Are waterproof nylon strips in water?

  I'm thinking or buy a sports watch. I want to wear the watch while swimming.

  Are waterproof nylon strips in water? from OK to wear while swimming?

  Your best option for swimming is the Sport Group.

• How to disable smart connector on iPad Pro?

  I have an iPad with smart Keyboard Pro 12.9. I would use the smart keyboard without the keyboard. In the past, I simply covered the smart connector with tape. Is it possible to disable the keyboard or the smart connector so that I could use the cover without keyboard is still active?

  No, there is no setting or control access to the smart connector.  It connects automatically whenever it is in contact with a compatible device.

• What is the difference between the channel strip and an insert?

  I'm confused a little, what's the difference?

  All (from top to bottom) is a channel strip, in the red zone are two insert (effect plugin) s.

  

• I want to buy a flash with lightning connector data storage.

  I want to buy a flash with lightning connector data storage.

  I'm between Transcend JetDrive™ Go 500 and iXpand SanDisk Flash Drive.

  What do you suggest me? Do you have another?

  My first priority is speed and iOS app use of data transfer.

  Hello

  To get the advice of a large sample of existing users of each product, you could more usefully read ratings on Amazon.com and reviews of products.

  If your questions are not answered there, you can also post a question of your choice.

• How can I get rid of the white stripes at the top of the screen that covers navagation bar?

  When I opened Firefix, there is a (sometimes blue) white stripe at the top of the screen that hides the navigation bar. I can't intervene except search because I can't click on the arrow invisible return, bookmarks, reduce or close the screen. I have to close the browser by right click on the Firefox icon in the task bar and click Close.

  First of all, could check you that Firefox is not full screen mode: by pressing the F11 key usually toggle between normal view and full screen. In addition, full screen, drag the pointer of the mouse to the top must cause the toolbar area to slide down. Then you can right click on an empty area of the tab bar (or the button '+' on the tab bar) and choose the output runs full screen in the context menu.

  Could test you mode without failure of Firefox? It is a standard diagnostic tool to disable some advanced features of Firefox and extensions. More info: questions to troubleshoot Firefox in Safe Mode.

  Does not work if Firefox: Hold down the SHIFT key when you start Firefox.

  If Firefox is running: You can restart Firefox in Mode safe mode using either:

  • button "3-bar" menu > "?" button > restart with disabled modules
  • Help menu > restart with disabled modules - try pressing Alt + h and then the letter r to trigger this command

  and OK reboot.

  Two scenarios: A small dialog box should appear. Click on 'Start mode safe' (not update).

  Any improvement?

• Fluid was detected in the connector of the lightning.

  I get a warning when my iPhone is plugged into its lighting cable saying 'Disconnect accessory lightning' "Liquid has been detected in the connector of the lightning" ' to protect your iPhone, unplug this accessory of lightning, and allow the connector to dry. "

  The cable is as dry as a BONE, the phone has never been exposed to water, other than standard moisture. I have several cables, and it happens with all of them.

  Clues?

  Thank you.

  Try a forced reboot. Hold down the Home and Sleep/Wake buttons at the same time for about 15 seconds, until the Apple logo appears. You won't lose anything.

  If the steps above do not help, you may need to test in an Apple store.

• Sorting unused Photos in the Photo in Photos 1.5 Strip

  In the Finder, I created a folder of photos, arranged the file by file name, then renamed pictures while they were in the general order, I wanted the photos to appear in a Photo book.  I imported this ordered all of the photos in picture 1.5, created a new album, copied Photos imported into the new album, click with the right button on the name of the album to sort the album by the title and the display of photos in the correct order.
  I chose the new Album, then created a new book.  Inexplicably, ordered Album photos are displayed in the Photo Strip in some apparent order of date with no option to sort the photos in the Photo Strip by title.
  How do a get the pictures in the strip of photos sorted by title so they can be moved to images in Photo book without scrolling back just looking through the Photo Strip?

  Those are sorted by date - on the only way to accomplish what you want is to add photos to the book a page at a time, place them in the book and then add the next page of photos

  LN