Fluid was detected in the connector of the lightning.

Similar Questions

• Error No. Boot Disk was detected or the drive failed - h8-1020 Desktop

  1 hp pavilion HPE h8-1020

  2. windows 7 64 bit

  3. Realtek PCIe GBE Family Controller series v2.38 24/12/10

  Error: No boot disk was detected or the drive failed.

  4. no changes to the system.

  After I restarted my computer about 7 times it finally started, so for me to be able to write this message.  However, this problem occurred several times over the last week or two. I get a blue screen, then the computer goes into a splash screen and I get the above error.  Of course, I'm 2 months past my warranty period, so I'm here, GROUND.

  Is my hard drive on its way? Is there a possible difficulty for this seizure completely breaks down?  Information to help save my machine would be great and much appreciated.  Thank you!

  P.S. I ran a diagnostic and all past test except the bootable disc.  But for some reason when I restart a little more time it get passed my system and begins running.

  Note: I created recovery discs and I backed up all my files.

  Hello:

  In my view, there is nothing you can do to repair the drive except to replace it.

  You can run the checkdisk utility and check both boxes.

  Please see the link below for more information.

  http://www.w7forums.com/use-chkdsk-check-disk-t448.html

  Please understand that this will only delay the inevitable at best.

  Paul

• HP Pavilion TouchSmart 23-f202: no boot disk was detected or the drive failed

  On startup, I get the message "no boot disk was detected or the drive failed.

  I bought a new H/D, installed and at startup I get the same message that I got on the old H/D.

  As there was no disc provided with the computer when I bought what I'm doing, had to do to get this sucker to the top and work?

  Hi @Jimmy56,

  Welcome to the Forums of HP Support! I understand that you had a type "no boot drive has been detected" error at startup to the top, and you have replaced the hard drive and have the same problem. I'm happy to help you with this.

  If replace you the original hard disk, you can use the following to test the hard drive. It is possible, there was a connectivity issue and just re-allocation of places the hard drive could make a difference. Computers HP - display of error HDD before starting the computer

  The most recent hard disk you put in, if not there was no operating system installed, you'll get the same type of message. You could make the same diagnosis of HDD from the link above, just to make sure that the disc is good.

  Please let me know the results, but so just install the original in the system hard disk works, and it starts correctly, so please mark this message as a solution. Bravo would be appreciated as well.

• ENVY 20-d010t: "ERROR: no boot disk was detected or the disc has failed." On HP Envy 20

  Hello-

  I have a 20 WANT all-in-One PC and until yesterday it was working fine. When I turned on my PC, a black screen appears with the message: "ERROR: no boot disk was detected or the disc has failed." I followed the instructions on this post and ran a Test drive in the BIOS. I ran both the Quick Check and balance of large and both have been adopted. I don't know what to do now. All solutions?

  Thank you

  mgmartinelli

  Future viewers of this post.

  I took my PC to the Geek Squad at my local Best Buy store and it turns out that Windows was just corrupted. All you have to do is to do a full restore using recovery discs. For more information about your model, I would just search on the internet.

• A fatal bus error was detected on the function of the peripheral bus component 0 7 0

  Hi all

  I'm trying to diagnose a hardware problem with my Dell PowerEdge R410. The problem occurred after a kernel patch and reboot linux security (I'm under Ubuntu 14.04 and I'm on Linux 3.13.0 - 100-generic). Initially, the machine would crash when starting in the BONE, but I managed to do always start too.

  I see the following errors:

  --------------------------------------------------

  Severity: critical
  Date and time: Saturday 22 Oct 05:50:30 2016
  Description: A fatal bus error was detected on the function of the peripheral bus component 0 7 0.

  Severity: critical
  Date and time: Saturday 22 Oct 05:50:30 2016
  Description: A fatal bus error was detected on an element at location 1.

  ----------------------------------------------------

  I'm having a hard time figuring what component, it exactly. Here is the result of lspci:

  ------------------------------------------------------------------------------------------------

  00:00.0 Host bridge: Intel Corporation 5500 IO Hub port ESI (rev 13)
  00:01.0 PCI bridge: Intel Corporation 5520/5500 / X 58 i/o Hub PCI Express Root Port 1 (rev 13)
  00:03.0 PCI bridge: Intel Corporation 5520/5500 / X 58 i/o Hub PCI Express Root Port 3 (rev 13)
  00:07.0 PCI bridge: Intel Corporation 5520/5500 / X 58 i/o Hub PCI Express Root Port 7 (rev 13)
  00:14.0 PIC: Intel Corporation 7500/5520/5500 / X 58 i/o Hub System Management records (rev 13)
  00:14.1 PIC: Intel Corporation 7500/5520/5500 / X 58 i/o Hub GPIO and Notepad records (rev 13)
  00:14.2 PIC: Intel Corporation 7500/5520/5500 / X 58 control status of e / Hub and RAS records (rev 13)
  00:1 a. 0 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4
  00:1 a. 1 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5
  00:1 a. 7 USB controller: Intel Corporation 82801JI (ICH10 family) USB2 EHCI Controller #2
  00:1d.0 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1
  00:1d.1 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2
  00:1d.2 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3
  00:1d.3 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6
  00:1d.7 USB controller: Intel Corporation 82801JI (ICH10 family) USB2 EHCI Controller #1
  00:1E.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90)
  00:1F.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller
  00:1F.2 IDE interface: Intel Corporation 82801JI port (ICH10 Family) SATA IDE Controller #1 4
  00:1F.5 IDE interface: Intel Corporation 82801JI port (ICH10 family) SATA IDE Controller #2 2
  01: 00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5716 Gigabit Ethernet (rev 20)
  01:00.1 Ethernet controller: Broadcom Corporation NetXtreme II BCM5716 Gigabit Ethernet (rev 20)
  Serial Attached SCSI 03:00.0 controller: LSI Logic / Symbios Logic SAS2008 PCI - Express Fusion - MPT SAS-2 [Falcon] (rev 03)
  04:03.0 VGA compatible controller: Matrox Electronics Systems Ltd. MGA G200eW WPCM450 (rev 0a)
  Fe: 00.0 Host bridge: Intel Corporation Xeon 5600 Series QuickPath Architecture generic Non-core records (rev 02)
  Fe: 00.1 Host bridge: Intel Corporation Xeon 5600 Series QuickPath Architecture system address Decoder (rev 02)
  Fe: 02,0 Host bridge: Intel Corporation Xeon 5600 Series QPI Link 0 (rev 02)
  Fe: 02.1 Host bridge: Intel Corporation Xeon 5600 Series physical QPI 0 (rev 02)
  Fe: 02.2 Host bridge: Intel Corporation Xeon 5600 Series Mirror Port link 0 (rev 02)
  Fe: 02.3 Host bridge: Intel Corporation Xeon 5600 Series mirror Port link 1 (rev 02)
  Fe: 02.4 Host bridge: Intel Corporation Xeon 5600 Series QPI Link 1 (rev 02)
  Fe: 02.5 Host bridge: Intel Corporation Xeon 5600 Series physical QPI 1 (rev 02)
  Fe: 03.0 Host bridge: Intel Corporation Xeon 5600 Series Integrated Memory Controller Registers (rev 02)
  Fe: 03.1 Host bridge: Intel Corporation Xeon 5600 Series Memory Controller target address decoder built-in (rev 02)
  Fe: 03.2 Host bridge: Intel Corporation Xeon 5600 Series Integrated Memory Controller RAS Registers (rev 02)
  Fe: 03.4 Host bridge: Intel Corporation Xeon 5600 Series integrated Memory Controller Test Registers (rev 02)
  Fe: 04.0 Host bridge: Intel Corporation Xeon 5600 Series memory controller channel 0 control integrated (rev 02)
  Fe: 04.1 Host bridge: Intel Corporation Xeon 5600 Series integrated controller channel 0 address memory (rev 02)
  Fe: 04.2 Host bridge: Intel Corporation Xeon 5600 Series integrated memory controller 0 (rev 02) grade channel
  Fe: 04.3 Host bridge: Intel Corporation Xeon 5600 Series integrated memory controller channel 0 control thermal (rev 02)
  Fe: 05.0 Host bridge: Intel Corporation Xeon 5600 Series integrated controller channel 1 controls memory (rev 02)
  Fe: 05.1 Host bridge: Intel Corporation Xeon 5600 Series integrated controller channel 1 (rev 02) memory address
  Fe: 05.2 Host bridge: Intel Corporation Xeon 5600 Series integrated memory controller channel 1 row (rev 02)
  Fe: 05.3 Host bridge: Intel Corporation Xeon 5600 Series integrated memory controller channel 1 control thermal (rev 02)
  Fe: 06.0 Host bridge: Intel Corporation Xeon 5600 Series integrated controller channel 2 controls memory (rev 02)
  Fe: 06.1 Host bridge: Intel Corporation Xeon 5600 Series integrated controller channel 2 (rev 02) memory address
  Fe: 06.2 Host bridge: Intel Corporation Xeon 5600 Series integrated memory controller channel 2 rank (rev 02)
  Fe: 06.3 Host bridge: Intel Corporation Xeon 5600 Series integrated memory controller channel 2 controls thermal (rev 02)

  ------------------------------------------------------------------------------------------------

  So, one of the components seems to be "00:07.0 PCI bridge: Intel Corporation 5520/5500 / X 58 hub of e/s PCI Express Root Port 7 (rev 13)", but I'm not clear as to what this component is
  and what it connects too. Crack, "a fatal bus was detected on an element at location 1." seems too vague. What is slot 1 in this case?

  My questions are:

  What components apply to critical errors?

  I have to do things in the following order:

  -Unplug the power cord and hold it for 20 seconds
  -Firmware updates
  -Try reinstalling components
  -Replace parts

  PS. I'm no longer under warranty

  Thank you

  Dave

  Hello

  Location 1 must reference slot PCie 1. It is very likely the slot in which the PERC controller is. Your order of troubleshooting is correct. If it's the only occurrence, resettlement and the firmware update are probably enough.

• ERROR: no boot disk was detected or the disc has failrd

  HP ENVY h8-1534pc with windows 8.

  error: no boot disk was detected or the drive failed.

  tried to run the recovery cd ROM even error. No cd or hard drve no indication in the boot order.

  out of resources

  Hello! Here are a few responses from members of the forum about your problem. See if you can find a solution from them. http://h30434.www3.HP.com/T5/forums/SearchPage/tab/message?filter=labels%2Clocation&location=Forum-Board%3AOSandSW&q=no+boot+disk+has+been+detected

  Dokie!

  PS It doesn't look good for me. Good luck and thanks for posting back.

  It has been my experience in the past that a message as this means that either the operating system is corrupt or your hard drive is dead. If your hard drive does not show in the boot order, it's a major sign of a bad HD, but not100%.  There are several free testers HD. Most have the back, which means that you don't have to have an operating system to start their. If you are not able to test your HD with F2 or F11 functions, try one of them. You will need to burn an ISO to a CD file.

  http://pcsupport.about.com/od/toolsofthetrade/TP/tophddiag.htm

  PS2 there may be answers best of the latter. Weekends are slow at times. I'm still slow

• Whenever I try to send a fax, I get error "no dial tone was detected. The telephone line is busy or not connected to the computer. »

  Whenever I try to send a fax, I get: "no dial tone was detected. The telephone line is busy or not connected to the computer. "Any ideas?

  You can't send a FAX via a connection to broadband. Fax is essentially specialized phones and requires that a service composition is used at BOTH ends.

  You can buy an analogue Fax/modem (USB types work well enough) or use a service to convert fax email...

• installed the file ISO of ESXI 5.5.0 of trialware on a PC at home that has a memory of 8meg, installed correctly, then on reboot I get 'no boot disk was detected or the drive failed', I'm boot from the hard disk, any ideas?

  installed the file ISO of ESXI 5.5.0 of trialware on a PC at home that has a memory of 8meg, installed correctly, then on reboot I get 'no boot disk was detected or the drive failed', I'm boot from the hard disk, any ideas?

  Welcome to the community,

  Please take a look at for example http://wp.secretnest.info/?p=697 to know if this is the problem you are facing.

  André

• Re: BSOD problem was detected on the Satellite L40 - 14N

  Hello

  have been unable to fix a fault on my laptop. BSOD problem has been detected and windows has shut down. I was told by someone that this was resolved when they replaced their hard drive.

  Could someone tell me what hard drive I need to get?
  Once I have to get one and put it in the machine should it restarts just using the system recovery disk, because it is what I have provided with or will it get other new software?

  I hope someone can help. Really lost without a laptop!

  Hello Netties

  Please do not be angry on me, but I do not understand why you start the second wire on the same issue. All this can be clarified on your original on this BSOD problem thread.

  In any case, if you have a warranty valid, please don't spend your money for the new hardware before clarify you this with maintainer authorized Toshiba. Maybe you are right on HARD drive, but please first check with the ASP.

• I have corruption was detected in the message of mananger feature as well.

  I tried to do a bit of what you're saying, but I don't have At & t or dell. I have a HP and use Tmobile for the internet. what I do...? What is a power supply issue?

  Thank you

  Stacy

  Hello, Stacy,.

  Error: "Corruption was identified affecting features Manager, Backup has been loaded.

  http://www.att.com/eSupport/article.jsp?SID=KB91761&CV=820#fBid=EHg6ek5qPlF

  I believe you are referring to this link in your original post-

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-security/corruption-has-been-detected/522f0f34-8b7b-4b72-86e6-df6ed53933c8

• Error: no boot disk was detected or the drive failed.

  I turned off my computer last night and when I turned it back today I got an error "not detected no floppy or defective disc.  The computer is a desktop computer of Pavilion P7-1011 that running Windows 7 Home Premium 64-bit.

  Is there a way to fix this, or that I lost everything on my computer?  I had the computer since March 30, 2012

  I recommend that you start your PC and go into BIOS then select Diagnostics F2 and run the hard drive diagnostics test.

  

• Pavilion 500 - C60: new office reads, "ERROR: no boot disk was detected or the disc has failed" at startup.

  Just bought Pavilion 500 - C60, running Windows 8.1 64-bit and am doing everything on old HP running Windows Vista Home Premium SP 2. Has not gone smoothly from one thing to another, but I think everything comes together. A couple of days, began to receive the error message at startup or, if I COULD do so that it starts would go for awhile and then would get an ERROR message, requiring restart. Usually after obtaining the error message several times, the computer would then initialize. Tonight, I couldn't override the error message for anything! When you press power button / stop, I hear (HD) running for a few seconds, everything is silent, and then the error message appears on the gray screen dark in white letters, BACK very and sinister looking! Any suggestions? Had the computer about two months and it has not been easy.

  Not good!  Check all the connectors and the hard drive to make sure that they are correctly wired in place. Make sure that your cable is not reversed.

  Contact the seller if still under warranty for repair.  This could be the hard drive or motherboard and the problem lies the only diagnosis from a repair facility.

• ENVY h8 - 1520t: error: no boot disk was detected or drive failed.

  Yesterday, when I turned on my computer, it was really slow and I could not open any programs. Then it went all blue and white. When I rebooted, I see "control the presence of .media, media, start the PC via ipv6, then error: no boot disk was detected or the disc has failed." I tried to hit f11, but it fills the entire screen with the error message. He died or hope?

  Looks like your hard drive has failed.

  You need to maybe replace the disk and reinstall Windows.

  Please use these instructions to test your hard drive.

  * Works even if your PC will not boot to Windows.

  If you found my answer helpful please say thank you by clicking on the icon of the thumb. If my answer has solved your problem, please mark it as accepted Solution. Thank you!

• What does "a parity error was detected on \Device\ide\idePort0" mean and how can I fix?

  I have a Pentium 4, XP SP3, 2 HDs installed, and I don't think I have SCSI but in my registry, it shows the HDs and two CD - RW and DVD drives listed under SCSI and there is no topic such as IDE, Atapi or AT (the area I'm talking about in the registry is: \HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\) so I don't know what is happening in this area...? Anyway, everything else refers to above devices IDE or Atapi etc..

  As well as the above parity error, I noticed a little more that I will add here:

  "The driver has detected an error on \Device\Harddisk0\D controller" (this is an ALL NEW HD)

  "The device, \Device\Harddisk1\D, has a bad block" (it's second HD giving the same error msg, the last HD failed and this is used)

  "The device, \Device\CdRom0, has a bad block" (this is my CD - RW drive, which seems to work very well, it's the DVD player that is not working properly)

  "While validating this \Device\Serial0 was really a serial port, a fifo was detected. The fifo will be used. »

  All of these errors are coming together for the most part. Please help as I just replaced a hard drive failing during the summer, now it is looking like another is a failure, but I want to know if something else in my computer can cause drives to fail, or causing errors in some way, or any other information anyone can give me to help before you start the process of replacing a HD failure (again!)

  Thank you... Denise

  Hi groovydee,

  Method 1

  I suggest you reinstall the controller and chipset drivers by contacting the manufacturer of the computer, check to see if it helps.

  Method 2

  If the previous step fails, then you need to check disk scan on the hard drive to scan and difficulty of bad sectors on the disk.

  How to perform disk error checking in Windows XP

  http://support.Microsoft.com/kb/315265

  Note: While running chkdsk on the drive if bad sectors are found on the hard drive, then chkdsk attempts to repair this area if all the data available in this area may be lost.

• While in "Event Viewer-System", "an error was detected on device\Device\Harddisk2\D during a paging operation what is this error,"D"drive" is a dvd - rw drive empty on the front of our Tower? :

  We had the people that our PC reconstruction after an accident some time ago, say "it seems that the Windows swap file was somehow moved on the disk"D", and it should be on the main 'C' drive.  Microsoft sent us an email with instructions on how to reset the Windows paging on 'C' drive system and to reset the minimum and maximum space allowed for it.  We did it, but the ' warnings are still there. " The "D" drive is a drive of dvd - rw empy on the front of our Tower.  Most of the time it is empty, as it is now.

  What are they and how to fix it?  I'm 73 years old and still learning.    Grandpa

  Hello

  Check to see if that helps!

  http://www.techsupportforum.com/forums/F16/event-ID-51-nf68i-an-error-was-detected-on-device-device-Harddisk0-d-during-a-PAG-273585.html

  http://support.Microsoft.com/kb/244780/en-us