Myrio digital channels always HIGH

Similar Questions

• Toshiba DVR80KF DVR is not able to keep registered digital channels

  Hello
  I'm not sure this is the right section but I try.
  I use the DVR in topic since January 2012 when I bought it.
  Now every day that the DVR is not able to keep registered digital channels.
  Now the automatic syntonization of digital channels. Everything is allright.
  Tomorrow, all channels are missing and I do the update again.

  You have any suggestions to fix the problem by myself or the DVR has to fix in a center of Toshiba?

  If so, is that I believe that this issue is covered by the warranty of the producer, isn't

  Thank you very much for yr help

  Hello

  I found a manual on this unit very:
  http://www.Toshiba-OM.NET/DVD/PDF/English/DVR80-English.PDF

  the 21 page provides information how to parse and store the channels.
  Check all the settings and follow the instructions.
  If no channel has been stored, the antenna confirmation will appear. Then you must press ENTER to start the auto scan new or press RETURN to cancel the initial settings.

  In other cases, I think that your problem could be related to hardware issue.

• Portege 3480CT lack always high-speed mode frequency

  One of my 3480CT Portege lacks always high speed frequency mode, but it has.

  I couldn't find the setting always high since there were only two options available for the power setting in F1 that are still weak and dynamically switchable only menu.

  Hello

  Sorry, but I don't understand your problem. Can you please specify more? As far as I know if you want to change different profile you must use the FN + F2 key combination.

  You can make individual settings for each mode in standby electricity by clicking details.

• Frequency of the system on a laptop Satellite A100 - 01 L must be always high

  Hello

  Because I'm a player battle field there is a problem of speed with my laptop.
  It's a portable Satellite A100 - 01 L tactfully 1.73 GHz normal system. (2 GB of RAM, 120 GB HD).

  System frequency changes between 800 MHz (without hard work...) and 1.73 GHz (if it seems to be necessary). In the system BIOS can select a 800 MHz (named slow ') or a dynamic clock speed (called: 'dynamic' modus).
  My question is: is it possible to set the system clock always to 1.73 GHz?

  Thank you.

  HM, normally it should be also a "High" option or something as "always higher". So, I suggest you to perform an update of the bios and then to check whether this option is available.

  Otherwise, you should look into the toshiba powersaver and make sure everything is up.

  Welcome them

• List of digital channel 32HL 833 drops sometimes

  Hello

  My Toshiba 32 HL 833 sometimes simply removes all digital channels and refuses to be new.
  The only solution so far is to reset the TV.

  But then I have to organize all the lists of the channel again.
  Is there another solution or can someone help me why tv refuses to show digital programs?

  I updated the firmware on the TV but it did not help, today he dropped again.

  Hello

  To be honest I don't know what's wrong here, but I put m t think you can do much more to reset the TV or to update the new firmware.
  If this problem persists, I recommend contact the Toshiba service technician to check the TV material.

• Qosmio G20 154: not all digital channels under MCE

  Anyone know why under MCE not all digital channels are tuned, all using the Cyberlink Cinema Manager all channels are tuned regularly?
  Thank you

  Enzo-ita Skype

  Hello

  I found this Microsoft Knowledgebase document:
  http://support.Microsoft.com/default.aspx?scid=kb;en-us;555330

  I don't know if it will help you to solve the problem in Italy, but you can check it out.

  I also found this page that describes HDTV in Windows XP Media Center Edition 2005.
  It is said;
  To check online what digital TV channels are available in your area, go to AntennaWeb Titan TV. The two Web sites provide tools to identify what digital TV channels are available in your area for live broadcasts.

• "No valid source or target channels specified. Cannot run. "error when you try to convert to digital channel waveform

  I'm trying to convert a waveform channel in one digital channel and a channel of absolute time, but I get the "no valid source or target channels specified. Error cannot run. ».

  I'm trying to concatenate several files TDMS InsightCM so I can display the data in a continuous flow over time. If the first file loaded (one of the channels in the group "Signals") convert the same channel, it works fine, but when I try to do the same thing with any of the channels from the second file (one of the channels in the group "Waveforms1"), I get the error.

  

  Hi JEBalles,

  I was able to reproduce this behavior when I chose a digital channel as my channels to convert. In this case, it looks like you run the operation on the speed profile > Mod1-Ch0 A NL, which is a digital channel.

  Could you try to select a waveform another channel? It looks like [3] Mod1-Ch0 A NL is a waveform channel.

  Kind regards

• Comparing two digital channels or waveform

  Hello

  How to compare two digital channels or the y-axis of the same lengths waveform channels and find the line that has about the same value in the channels. For example, suppose we have two digital channels X and Y which has about the same value in line 15. I need to write a script to find out in which line the canals coincide.

  Kind regards

  X.Ignatius

  Hi X.Ignatius,

  I subtract channels and use the CHNFIND function to search for string values that are zero or nearly zero.

  Greetings

  Walter

• Easy one - Show 6 entered a digital channel

  Hello

  I have a Setup with 3 LEDs which, within each of them is 2 led, so total I have 6 flashing LEDs. I got one of the sons of the signal 6, connected to my digital channel P0.6 on my DAQ 6351.
  I would just get these 6 signal showed separately on a chart.

  I tried a number of things, but none of them would show them separately - how can I retrieve my DAQ.mx digital input 6 signal?

  I have delete my project for these chart I tried to create an overview.

  Thanks in advance
  

  That makes no sense at all. You need 6 different lines to 6 different data acquisition channels.

• How to set up digital channels to change values on the trigger and the counter in c#

  Hello world!

  I work with the driver NI - DAQmx 6025 and want to know, how do I configure the digital channels in c# for control lines different ports by trigger rising "PFI0" and the meter "ctr0.

  digitalWriteTask = new Task();
  digitalWriteTask.DOChannels.CreateChannel ("Dev1/Port3 / line0:7", "", ChannelLineGrouping.OneChannelForAllLines);
  digitalWriteTask.Control (TaskAction.Verify);

  digitalWriteTask.Triggers / / how to configure to change Digital line on rising "PFI0"?

  digitalWriteTask.Timing / / how to configure to change Digital line on County "ctr0?

  -------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

  Hi an alle!

  Am mit dem OR-DAQmx 6025 und möchte like wissen, die ich wie digital channels in c# konfigurieren muss um einzelne Ports der Leitungen auf dem Trigger "PFI0" und dem Zahler "ctr0' anzusteuern.

  digitalWriteTask = new Task();
  digitalWriteTask.DOChannels.CreateChannel ("Dev1/Port3 / line0:7", "", ChannelLineGrouping.OneChannelForAllLines);
  digitalWriteTask.Control (TaskAction.Verify);

  digitalWriteTask.Triggers / / Wie konfigurieren, um den logical Pegel eines feature pine bei der der zu winds PFI0 goods?

  digitalWriteTask.Timing / / Wie konfigurieren, um den logical Pegel eines pines beim ctr0 zu go digital?

  NEITHER told me, with the NOR-DAQmx 6025 driver not supported!

  ICH habe von NOR learn, dass dies mit der 6025 OR AQmx supported wird nicht!

• DAQmx Read is limited to 9 digital channels?

  I'm reading several digital channels with DAQmx Read (Digital 1-d Wfm NChan NSamp). The output of the DAQmx Read vi is a table 1 d of digital waveforms. If I put this output through Cluster in the cluster that results seems to be limited to 9 elements, data [0] through data [8]. DAQmx Read output is limited to 9 digital waveforms? I'm using Labview 2009.

  No, this is not done, is choosing the Cluster size. Nine is the default value. Right-click on it to change.

  Because you have to change it every time you change the number of channels, are you sure want to use clusters instead of just working with a table?

• Digital channel in front of artist name or Album

  I have synced my device using WMP (latest version), when you view the folders on my Clip +, I found the one the names of the artists and albums have a digital channel in front of the name of the artist or the album.  When I view the Clip files + via Windows Explorer, I don't see the digital channel.

  No idea why some of the artist name/album names have this digital channel and how get rid of?

  Thank you

  Eric

  To prevent this, set the USB mode on the player to MSC.

• Windows Media Center Vista don't tune in digital channels of PCI digital tuner tv.

  I recently installed a new Hauppauge WinTV HVR-1600 NTSC? ATSC/QAM tuner in my computer. Its a dual core 2.66 mhz 4GB Ram running Windows Vista Home premium with Windows Media Center. The tuner is made to work with Windows Media Center according to its box. He also had his own software cleaner, IE. WinTV, which I also loaded. I have an antenna hanging good input on the tuner card. That same exact antenna wire hooked to a digital TV Gets the following strings... 6.1 and 6.2 - 6.3 - 8.1 - 8.2-8.3-17.1-17.2 - 17.3 - 22.1
  WinTV those gets exactly the same channel list and can display them all. Windows Media Center, after the execution of the installation routine, list the same channels, but do not think that all. Problem channels are 8.2 - 8.3 - 17.1 - 17, 3.  These channels show in the guide as "No Data Available" and when you select them, there is no signal detected. Yet, channel 8.1 and 17.1 gave Guide and discover very well. It is interesting when you go through special antenna Signal: settings: TV: Digital TV the 8.2 problem channels - 8.3 - 17.1 - 17, 3 list all the and are verified with check marks and show full signal strength. I spent time trying to play with the Guides Add announcement & edit channels and add missing channels. Also, I spent time with "Set Up TV signal" several times.
  Any suggestions? Why is the windows media center grateful but not display secondary digital channels, still recognizing and displaying the primary digital channel very well. It can be the signal or the pilots, because MyTV of Hauppage shows them all very well.
  Help?

  Try windows update.  I use this card with media center 7 and had no problem getting all the digital channels.

• Windows Media Center will not scan digital channels using a dual tuner (analog/digital)

  I have an AverMedia Volar Max tuner which is analog and digital double Windows 7 Professional
  Media Library 'sees' the tuner as an analog tuner and properly identifies all the analog channels, that I see on TV.
  However, none of the digital channels are detected. I have not found a way to "force" a search using QAM256 or any other research of digital formats.   Using the tuner, cable and connections the same BUT with a linux sotware (mythtv) all digital channels have been identified.
  Is the problem because its analog and digital modes? How can I force Media Center to see the digital capacity of the tuner?

  Might have been a better place to look for information on the AverMedia Max Volar tuner AverMedia USA site.

  If you had looked here to find the latest drivers or to read support information, you would have found:

  The support of the AVerTV Hybrid Volar MAX QAM signals on Microsoft Windows Media Center?

  Currently, Microsoft Windows Media Center does not signal QAM. You will need to use our AVer Media Center in order to receive the QAM signal. Please download the application on our website programs: http://www.aver.com/mpd/support/download/combopcie.html

• Cannot get digital channels will appear on kdl-40xbr7 it worked last week.

  Since my grandchildren where here last week my TV KDL-40XBR7 only list digital channels. When you perform the initial installation, it finds all analog channels digital channel search starts it concludes digital a few then scanning stops at step 4 of 7 and shows the analog channels, but no. I tried everything even to put tv back to factory settings and install still no digital channels. Does anyone have an idea what could be wrong thank you.

  discovered step son plugged a device bundles and it corrupted digital firmware. I downloaded the firmware and loaded on the TV and everything works fine now.