Name of resource VISA includes serial number

Similar Questions

• get the name of resource VISA

  I connect serial port COM3 to a digital multimeter, I can sure that COM3 is displayed in Device Manager. but I don't know if COM3 is in the name of resource VISA list. If COM3 is not in the list, I want to update resource VISA name.

  So my question is how to program can get the entire list of the name of resource VISA, so that the program can compare resource VISA with COM3 automatically name? How the program can update the name of resource VISA, if COM3 is not in the list?

  LabVIEW 2011 windows 7

  Thank you

  Control of resources VISA automatically displays the available visa resources. If it isn't then looks like there was an error in the installation of NI-VISA.

  An alternative is to use your own control, as suggested here: http://forums.ni.com/t5/LabVIEW/VISA-resource-name-control-want-to-refresh-list-of-COM-ports/td-p/13...

• Can not find the name of resource VISA

  I am trying to run the example code, provided by the manufacturer with a 3a Keithley 2420 SourceMeter.  It is turned on and put in place for 488,1 protocol GPIB.  It is connected to my computer via a GPIB KUSB - 488A cable.  On the front panel of the example program, there is a menu drop down titled "VISA resource name."  The two options at my disposal are LPT1 and COM1, but I don't think one of this is the name of the resource on the right.  Does anyone know what the name of resource VISA should I use with the Keithley, or how I can find this? If it helps, I have provided the example program I use. Thanks in advance!

  As a general rule, only the material NOR will be recognized in MAX and you wouldn't get any VISA resource for Auditors not - NOR. If there is a VISA for the Keithley driver, you can try to install as secondary visa driver and enable Tulip MAX. Keithley support support is the best place to ask questions about the installation of their hardware to LabVIEW.

• HP Envy Touchsmart17: Name of bad product and serial number in the BIOS has BEEN changed

  I have hp envy touchsmart 17 laptop changing a bios code.

  Dear I red your answer and I appreciate it. I did not plug the PC, I want to get the original serial number / product of the PC. Changed before you buy it, I don't want to get it back for certain needs I have to take. Please clarify for me on how to get it back. FYI, I went into my BIOS to factory setting and I couldn't because the HP Support responded by saying that my product has been changed and cannot get it.

  Please please answer

  Sincerely

• CS4 install a new computer does not accept the included serial number Acrobat Pro

  I bought CS4 Design Standard through my University.  I used it for years, and I'm pretty happy with it, I don't want to pay for a newer version.

  Recently, I bought a new computer and went to reinstall it on the new computer.

  The installation went without problems

  Recovery of my series of Adobe has been frank.

  Amnesty International, PS and ID agreed the serial number without problem.

  Acrobat Pro says that serial number is invalid.

  I spent two hours on the cat and in the end he said that the relief phase was not available for CS4, but was only available via online forums.

  So I initially posted the Acrobat Forum 3 days ago, and while my post has dozens of viewers it has none.

  How do I get this resolved?

  I don't think charitable thoughts on Adobe right now.

  http://forums.Adobe.com/message/6054756#6054756

  System,

  I finally (after 5 attempts) through the swamp on the other side.

  Here's what I did...

  1 uninstalled all of the CS4 program.

  2. manually deleted the folder under Program Files Adobe

  3. Ran the CleanCS4 program, who told me that I had to run microsoft windows install clean up utility

  4. has opened a new Director on my office profile

  5 install CS4 here

  6 open photoshop

  7 open acrobat.

  (I think that's everything now works).

  g'luck!

• Name of resource VISA get does not have USB serial ports

  We built an application on a computer that had a built-in serial port - COM1.  We have the option to change the COM port in the application.  We have installed the application built on a computer that has no serial port, but installed a USB serial Converter which records as COM3.  LabView does not see this port, even with a test application to return only the names of VISA resources.

  We have verified that the port is good with another program (a Modbus Simulator) and installed the last TIME VISA v4.41 separately without result.

  Any suggestions for more troubleshooting would be extremely useful.

  Joe T.

  My main of the application still does not work, but now the little test ones are.

  Here's what I did:

  1. update my LabView 8.5 with the last VISA - 4.4 runtime.  This update the installer as well.

  2. added the install MAX for the build.

  3. adding the Support of Configuration of NI-VISA for construction

  4. uninstalled the app and reinstalled with the new volume of the system.

  When I run MAX, COM3 appears.  He also appears in the application of test resources.  The simple test Modbus to write the program works, too.  I have a sneaky feeling that COM1 can be hardcoded somewhere in the parent application; our next task is to find where communication breaks down in our code.  The bottom line seems to be a lack of experience with the demand of our manufacturer.

  Thanks to all who participated!

  Joe T.

• How to use USB with the name of resource VISA?

  Hello

  I am new to LabVIEW and I'm working on a code that must acquire data from a measuring device. This unit has only a USB output, so I have to work with it. As far as know the block that is used to refer to an external port is VISA resource name. I installed a driver that recognizes the serial ports, and they appear in the list of VISA resource file to the front panel. So I thought that installing the DEVICE driver so that the USB ports would appear. I installed and nothing of USB ports. I don't know it's as simple as that, or work with USB ports is a little more difficult. I tried many things and nothing worked I am here.

  PS: I noticed that the version of the driver is 64-bit (my pc is 64-bit) and my LabVIEW version is 32-bit, what could be the problem?

  The device incidentally is Digital Analyzer WT500, Yokogawa.

  Thank you.

  Victor,

  the suggestion driver instruments is to make it easier by using the instrument.

  Normally, you need to install a player from the manufacturer (if it is not installed, the instrument appears as a USB in Device Manager) and the driver NI-VISA. But for some instruments, manufacturers have APIs that uses NI VISA to communicate with your equipment.

  In order to check whether your instrument appears correctly in Device Manager (as indicated by Yokogawa). If this is not the case, check whether Yokogawa has a suitable driver for this tool and install it.

  Is this clear?

  If you wish, you can contact NI Brazil support site or by phone (11) 3149-3149 Ext 3.

• IS THE NAME OF THE PROFILE INCLUDES THE NUMBER TOO?

  PROFILE_NAME IS FOLLOWED BY A NUMBER. COPY THE NAME AND NUMBER TO RESTORE MY PROFILE? WHEN I DID IT BEFORE THERE WAS NO NUMBER BEHIND THE NAME.

  The name of the folder is what it is. If you rename, Firefox may lose track of it, so I would leave just the full name, exactly as it is.

• VISA data serial number read

  Hello

  I'm starting to Labview (after a few years) and I have a problem with a reading series basic (using VISA) program.  The code is attached, and my problem is that I'm getting out of "FE FE FE", when I see in the Putty terminal it is count up to integers indefinitely - I can't quite grasp what's going wrong here (after much trial and error), so any help would be appreciated.

  Thank you

  Rob

  First thing to do is to use the configure Serial Port instead of the VISA opening and make sure that your serial port settings are current.

• How to set the name of resource VISA as a constant?

  I'm properly communicates with a device series using ModBus. The drop-down list on the front displays correctly COM3. I would like to remove from the drop-down list and set default COM3 on the block diagram. Can someone tell me how to do it please? Thank you very much

  Hello

  Right click on this drop-down list and select replace by, constant...

  So you can see the name of constant of Visa on the block diagram and no need to pull down...

  Pals

• I downloaded on my new computer suite Design Premium 5 and it says that my serial number is invalid

  I downloaded on my new computer suite Design Premium 5 and it says that my serial number is invalid

  Hi Kates,

  Please visit error: "serial number is not valid for this product". Adobe Creative Suite

  It will be useful.

  Kind regards

  Shelly

• Acrobat 9 pro reinstall do not accept the valid serial number

  HDrive on my laptop could not and had to quickly get the new laptop and reinstall all programs. Have Adobe Acrobat 9 Pro serial number. Reinstalled but the program will not accept the valid serial number for the underlying program, he went from level. This is the product of my Adobe account information. I am a frantic reporter trying to meet deadlines one just noticed I don't have that a few days left of the "30 Giorni", I was given as a test for the PROGRAM I ALREADY paid for! What can I do to fix this? Any suggestions greatly appreciated. I checked the forums a bit, but couldn't find a similar question. I'm starting to hate Adobe... no phone support, and 'chat' window, we recommend that you use online now has cobwebs on this subject, it has been sitting there so long w / no activity.

  Name of the product	Serial number	Version	Platform	Registration date
  Adobe Acrobat Pro	DELETED BY ADMIN	9.0	Win	June 4, 2010
  Adobe Acrobat	DELETED BY ADMIN	7.0	Win	April 15, 2007

  Yes, uninstall and run the cleanup tool before you install using the cleaning tool CC to resolve installation problems. CC, CS3 - CS6

  In the menu drop-down see what are the options eligible Acrobat 7.

  Failure, know that Acrobat 9 installer can generate a "challenge code". You who give customer service and they give you a response type Code to unlock it so it will take your serial number for Acrobat 9.

  Error: "this serial number is not for a product calling it" | CS6, CS5.5, CS5

  I'm a volunteer Forum, it's the customer who can only accomplish this process.

• Photoshop CS2 says my serial number is not valid and will not run.

  When you start photoshop CS2, I received a message that my name photoshop user, organization or serial number is missing or invalid.  I can't run photoshop.  I bought legally in 2005 (I know, I had this version for some time).  I used the program a few days ago.  How to solve this?

  You have an installation CD that can run the uninstaller for you?

  Removal of Windows process «»

  Insert the Adobe Photoshop CS2 CD in your computer's CD drive.

  1. start the removal process.

  As with installation, the first window that appears requires you to choose a language for the installer. After you select a language and click OK, the software license agreement appears. Read the software license agreement. If you agree, click on accept. If you click on decline, Setup will stop.

  Click on install Photoshop CS2 in the main installation screen, click on next to the Welcome screen.

  2 disassembly and repair.

  When Photoshop CS2 is already installed, you have the option to repair the current version, which solves any problem that may have the version installed, or you can remove the currently installed version. Click on delete and click Next. »

• VISA devices with the same serial number and the vendor ID does not work (0xBFFF003A)

  Hi all

  I need to acquire the data of two meters of power YOKOGAWA with VISA driver (USB connection).

  They work very well if used alone, but they do not work when are used toghether. In particular, when I plug in and turn on the two of them, NOR MAX shows me the following error message:

  0XBFFF003A (VI_ERROR_INV_SETUP)

  viFindRsrc return 0xBFFF003A (cannot start the operation because the installer is not valid (because of attributes defined in an inconsistent state).)

  Please make sure that VISA is properly installed on this system.

  Possible causes of this error:
  1. more than one passport may be to attempt to claim the same resource.  You can try to disable passport to understand which Passport is the cause of the error.
  2 you have connected multiple no configured plug-and-play devices that have the same name of the resource. For example, the vendor ID and the serial number may be the same.

  In fact, according to MAX, both power meters have the same serial number and the same vendor ID; so, this seems to be the reason why they do not work together.

  Can someone help me?

  Thank you all

  
  

• I thought indesign cs6 was included in my package of premium design cs6.  Why, when I try to open it, go to a window that says that I don't have a CC membership more and then quits without loading Indesign cs6.  It requires a serial number, but the s

  I thought indesign cs6 was included in my package of premium design cs6.  Why, when I try to open it, go to a window that says that I don't have a CC membership more and then quits without loading Indesign cs6.  It requires a serial number, but for my design premium cs6 serial number is not accepted by it.

  Hello

  Yes, you need to uninstall Adobe Creative cloud only, if you are unable to uninstall creative cloud through the tool cleaner and error message you shared above.

  Please go through the below mentioned location and remove the file name ""ffc " "

  
  

  MAC: \User\\Library\Application Support\Adobe\OOBE\

  Windows: C:\ProgramData\Adobe\OOBE\ (to view the AppData folder and program hidden data, see files, folders, file name extensions |) Windows XP, Vista, Windows 7)

  
  

  
  * After the removal of FFC file run the cleanup tool and uninstall Adobe creative only cloud.

  Let us know if this will help!

  Kind regards

  
  Sandrine