Need for other computers on the network to access my laptop computer to run a program

Similar Questions

• Network management problem, computer laptop Windows 7 will not find other computers on any network, however all other computers on the network can access Windows 7 laptop.

  Basically, the issue I'm having is that my laptop does not connect to any other computer to access the actions or other files.  Other computers on the network can access my computer laptop shares and files without any problems.  Operating system is Windows 7 Home Premium x 64.

  What I tried:

  restarted
  uninstalling and reinstalling the files and printers, sharing maps and restart after completion
  all disabled firewall
  tried with IPv6 enabled and disabled without change, so it is currently enabled
  tried on a Wi - Fi and the differences are listed below in the section work (work is wireless)
  able to ping other comptuers
  access to other computers is permitted by other computers

  problem extends over several networks, IE I noticed it at home last night and the followed problem my laptop at work this morning.
  The problem is slightly different on the two sites.

  At home:
  I can see the other computers on the network, but I am unable to access it, even if I have permission, but other computers can access to my laptop.

  At work:
  Cannot even find other computers on the network but they can find and access my laptop.

  I have worked on this problem of non stop for several hours and did much more than what is said, but I am unable to remember everything.  I should have been taking notes: P

  Here are the results of the ipconfig/all command (I removed the physical addresses for security reasons):

  Windows IP configuration

  Name of the host...: Radiation-G72
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Wireless Network Connection 2 wireless LAN adapter:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft Virtual WiFi Miniport adapt
  Physical address.... :  **
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. : hsd1.ga.comcast.net.
  Description...: Realtek PCIe GBE Family Controller
  Physical address.... :  **
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :
  ... Description: Atheros AR928X Wireless Network adapt
  Physical address.... :  **
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::f4e3:cd1c:6952:eb4d % 11 (Preferred)
  IPv4 address: 192.168.2.7 (Preferred)
  ... Subnet mask: 255.255.255.0.
  Lease obtained...: Thursday, February 4, 2010 10:50:32
  End of the lease...: Friday, February 5, 2010 08:29:36
  ... Default gateway. : 192.168.2.1.
  DHCP server...: 192.168.2.1.
  DHCPv6 IOOKING...: 234890707
  DHCPv6 DUID customer...: 00-01-00-01-12-4C-6E-91-00-25-D3-3D-FC-9A
  DNS servers...: 192.168.2.1.
  NetBIOS over TCP/IP...: enabled

  Tunnel adapter isatap. {1797D168-6FC8-4DDF-8338-4E214119C26D}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft ISATAP adapter
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Teredo Tunneling Pseudo-Interface:

  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  IPv6 address: 2001:0:4137:9e74:4ea:2920:b81a:cdc5 (Preferred)
  Address IPv6 local link...: fe80::4ea:2920:b81a:cdc5% 13 (Preferred)
  ... Default gateway. : ::
  NetBIOS over TCP/IP...: disabled

  Card adapt 6TO4 tunnel:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft 6to4 card
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Asked this question in the Windows 7 forum also because the problem was between windows 7 and Vista.

  Hello

  If it has started, you can try a system restore - an update "might" have caused the problem.

  1. try a system restore back to a point before that happened. And immediately thereafter enter
  Control Panel - Windows updates - top left settings and set it to download and informs you instead
  Automatic. Leave it until you are sure that everything is OK and then you can add them one at a time
  to troubleshoot BUT click right on and HIDE all the driver updates. Also stop at day of drivers like below
  and let this value - manually search for drivers when you think you need. (See how and why to)
  stop day of drivers below.)

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  To uninstall an update if you determine that there are problems - Panel - updated Windows - down left-
  Updates installed - uninstall

  I had completely forgotten the system restore!  While looking into the system restore, I found that when I moved into my new House and has cable Internet installed, the cable technology installed a program of comcast on my computer.  This caused me to not be able to connect with other computers.  After rolling back to install it before it works!   Thank you.

• Computer name change create problems for other computers on the network

  Hello

  One of our clients have a network of about 50 PCs. Two weeks back I need to change the names of some 40 computers for inventory purposes. There was no name of PC or IP address conflict. Next day, it was a mess, many users have complained that they are unable to connect to the terminal server or cannot log on to their PC.

  Yesterday, had to change the names of the 6 PCs and had the same problem. It is not the name of PC or IP address conflict.

  I did the same process of changing names to another customer, and there is no problem at all. What could be the reason for this customer?

  This issue is beyond the scope of this site and must be placed on Technet or MSDN
  http://social.technet.Microsoft.com/forums/en-us/home
  http://social.msdn.Microsoft.com/forums/en-us/home

• The administrator password for all computers on the network does not work for ONE of the computers on the network

  original title: the computers of network/administrator password

  The administrator password for all computers on the network does not work for ONE of the computers on the network. I need to log on as an administrator to install software, but the password does not work. It works on other computers, but not this one. How is this possible and how can it be solved?

  Hello
  Microsoft technical support engineers cannot help you recover the passwords of the files and Microsoft who are lost or forgotten product features. For more information about this policy, please refer to the below sticky

  http://social.answers.Microsoft.com/forums/en-us/vistasecurity/thread/3eba3150-8742-4264-be9f-0daaad2282cd

• Cannot see other computers on the network

  Am on XP SP3.
  When I go to network connections,
  Right-click on local area network
  Click Properties under the general tab,
  Click on install and click Service
  .. all I see is a list for a McAfee driver but nothing for Microsoft. I removed my computer some time ago with McAfee & he must have created problems that I can't see other computers on the network. Is there a Microsoft driver, I need to install and which will help to solve the problem of not seeing other computers on the network.

  On the general tab of the properties of your network connection to the LAN card, you should see a box under the heading "this connection uses the following items."  Most Windows XP configurations for home use have 4 entries in this box: Client for Microsoft Networks, QoS Packet Scheduler, file sharing and printers for Microsoft Networks, and Internet (TCP/IP) Protocol.

  If you don't have these, you need to install, even if you really need not the Scheduler of QoS packages.

  You seem to have got almost to the right place, but be aware that when you click on the button 'Install' in the box, you are given 3 choices: customer, Service and Protocol.  The "Client for Microsoft networks" is obviously a "customer." 'Internet (TCP/IP) Protocol' is a 'Protocol' and the other two are "Services".

  What elements you have installed?

• Unable to access server vm from other computers on the network.

  SE host: Windows 7 Edition home premium 64-bit

  VM Server OS: Fedora Core 9, with a NAT net configuration

  I can access the IP address of the server to the virtual machine to the host machine, but unable to hit if other computers on the network.  This is the first time doing this on a machine Windows 7, so please let me know if Miss me something, because I did it on other OS and it worked.

  Thanx

  As I posted in your second post...

  You need to configure port forwarding if you want to access the guest from outside the host. You must change the VMWare NAT configuration for this file (see you second post).

  The host can access the guest without the redirect because it shares the same (virtual) network (VMnet8) with comments. Do not externel systems. They must go through the physical host NIC first. This is where redirection comes in the game.

  AWo

  \[:o]===\[o:]

  = You want to have this ad as a ringtone on your mobile phone? =

  = Send 'Assignment' to 911 for only $999999,99! =

• WRT160N - can't see other computers on the network

  I installed a new WRT160N and now I can't see other computers on my local network, but I can access the internet on each of them.

  Y at - it a setting that I need to change or what I need to use static IP instead of DHCP addresses?

  If you cannot ping the other computers on the network, then check your firewall settings or any other security software blocking the connection.

• Cannot see other computers on the network of the office.

  I can't see other computers on the network from my office, but if I type in \\xxxxxxxxxxx I'm able to get on the other computers on the network. How can I have them automatically appear?

  I'm terribly sorry for wasting your time.

  I realized what the problem was. I've implemented the new computer exactly as the old, same name and everything. Come and find the computer name of the computer being the same as the old conflict and did not again see what was on the network.

  So the trick was unplug the old computer from the network.

• Client VPN prevents internet access from other computers on the network

  Hello.

  I run Client ver 4.6.03.0021 from an office on a network of 11 computers via a hub 16-port. Internet access is through an ICS gateway to the cable modem. Once I changed the modem cable to test a backup and then switched back to the original modem. After this, only computers that have the VPN Client (running or not) could access the internet. Computers that have no customer VPN can access only certain sites. Commonly viewed sites would say "site found. Waiting for answer", but the answer would never come and IE 6.1 cling. When I would try ping sites, it would fail. However, some sites such as Google.com would work.

  On one of the computers, on a whim of head, I installed the VPN Client but have not set up a connection. Now, this computer will connect to any website I want.

  Is there a fix easier to get access to other computers on the network without installing the VPN Client on each of them?

  Thank you

  H. Adams

  Hello

  Looks like you are running in MTU problem. The reason I say it is, automatically reduces the MTU value to 1300 VPN client during the installation for the whole system. That is to say all the client computer installed VPN that have MTU from 1300.

  Try to cut down the MTU of other systems that have no VPN client installed to 1300. If it's a Windows system, you can use Dr. TCP (free).

  Vikas

• Do not remember the WPA key. Other computers on the network

  I don't remember my WPA key and reset isn't exactly an option since I have other computers already configured for the existing key. I don't mind reset other computers as well if I knew for sure that it works. However, there is a discrepancy between the length of the WPA key on my Linksys (indicated as asterisks-33) and the length of the WPA key shown on the laptop of my wife (indicated as asterisks-63).

  I am trying to add a Wii to my network. Our router is currently not broadcasting the SSID, but I typed the name of the router in the Wii in any case. (She even will be able to find a network that is not broadcasting its SSID?).

  I also added the Wii MAC address to the list of trusted computers.

  Regarding the password, I considered to change but I'm worried I might spoil my wife configuration.

  When I go into my wireless settings, I see that I use a WPA TKIP encryption which is 33 characters long. However, when I go into the configuration of the network on my wife's computer, she says that his encryption key is 63 characters (WPA - PSK TKIP). Why the keys of different length?

  Is it possible to change the encryption key on the router to something I'd remember? If so, that will enter my wife's computer? Wouldn't make sense that what I typed in the settings wireless of Linksys (33 characters) would be the same as mine rather than 63 characters?

  I'm so confused.

  Any help?

  First, the County of asterisk is meaningless.  Even the number of characters in your password is a secret, so all good programmer who wrote your wireless network card driver shouldn't have a number of astrerisk which corresponds to your password.

  Set your "broadcast SSID" "enabled."  Do you really think someone will lose hundreds (or thousands) of hours of time to break your password, just enter a router WPA?  As long as you use WPA or WPA2 and a password, you shouldn't worry about your SSID broadcast.

  You can use any key (sometimes called password or password) you want, but all the keys (in router and all computers) will be the same.  Ideally you should use a strong password.

  Choose passwords (keys): you should never use a Word from the dictionary as a password. If you use a Word from the dictionary as a password, or WPA2 can be cracked in a few minutes. When you take your login password and key encryption (password or password), you must use a random combination of uppercase letters, lowercase letters and numbers letters, but no spaces. A connection password, must be 12 characters or more. WPA and WPA2 passwords must be less than 24 characters. Note: Your key, password or password should not be a space in it.

  Most individuals should have their routers defined so that "remote management" of the router is disabled. If you must have this option enabled, then your password needs to be increased to a minimum of 24 random characters.

  An additional problem is that Windows XP requires SP3 run WPA2 (WPA with AES =).

• Trying to create a unique folder for other clients on the network.

  I have a home network, both computers on the network, el capitan and el capitan MacbookAir iMac.

  the iMac user is IMAC_ADMIN and MacbookAir user is AIR_ADMIN, both have administrative privileges on the local computer. (I presume that the iMac user has no privileges on the MacbookAir, because it's a completely different system, and vice versa, Admin users should not be able to do anything on the other machines. Please confirm that this is a true statement)

  I turn on the iMac and log in as IMAC_ADMIN, and I turn on the MacbookAir and log in as AIR_ADMIN.

  My goal is to create a folder on the iMac that is accessible for the MacbookAir, and only in this folder.  Let's call the folder/Users/IMAC_ADMIN/Public /.

  I don't want access to anything else on my computer the MacbookAir user.

  For example, I would log the MacbookAir like AIR_ADMIN, go to the Finder application, then in the shared section, see the icon for the Public folder on the iMac.  When I connect to the icon with the pointer, there should be a window that opens, "select the volumes that you want to mount on"iMac", and the only thing listed is the Public folder.

  How is it possible in Mac OS X El Capitan 10.11.5 with AFP Protocol?

  Thank you

  You almost perfectly describe the scenario of the use of the folder "Shared" in Mac OS X.

  Inside your BootDrives 'Users' folder, there is a user/entity called 'shared '.

  Subsequently correctly instructions standardized in the link below, you can make this folder (and only this file) and shared its contents available (selected) users on your local network.

  This shared folder can also appear in the sidebar of a finder window, if you wish.

  This is probably the easiest way to do what you want:

  https://support.Apple.com/kb/PH21810?locale=en_US

• network printer shows off line but printsf by other computers on the network

  my brother mfc-7840w printer displayed offliine when I try to print from a computer on a network, but works fine on other computers on the same network. I remove and reinstalled printer. Works for a short time but when computer turned off and rebooted the printer go offline. a stop printer, etc.

  Hello

  Follow the steps in the link below and check if it solves the problem.
  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/network-printer-goes-offline-on-Windows-7/df4321de-EE25-423F-b1c9-d38957d50131

  Kind regards
  Afzal Taher
  Microsoft technical support engineer

• Machine of Windows 7 cannot see itself or other computers on the network.

  I work with a volunteer organization, is attempting to add a new computer to their network. Add the new computer is a laptop running Windows 7 Professional (32-bit, 6.1 build 7601).

  It is one of the three computers that connect via a wireless network, with the remaining three computers connected by Ethernet.
  One of the laptop is running Windows 7 Home Premium (64 - bit, 6.1 build 7601) and the laptop rest and three desktop computers running XP Professional (5.1, build 2600).
  The laptop running Home Premium has no problem with connectivity. He can see himself and all the computers on the network (with the exception of the new Windows 7 Professional machine). The XP machines can all be seen and also the machine Windows 7 Home Premium.
  The Windows 7 Professional machine, however, cannot see itself, or one of the machines running on XP. It may, for some reason, see the Windows 7 Home Premium machine.
  I can ping each computer on the network from him and he can ping other computers. I can even connect using his IP address and access the folders and files shared like this, but nothing I have seems to change him will appear.
  I tried to disable the Windows Firewall and Microsoft Security Essentials, neither of which has an effect any. The computers are all in the same workgroup and network machines Win 7 is set to work on both.
  I can't understand why this new computer should have these problems, I'm not a professional so there is probably something basic, I missed, but if anyone has any ideas I would be much obliged.
  Thank you very much.

  Hello

  The question you have posted is related to Windows 7 connected to an organization and would be better suited to the TechNet community. Please visit the link below to find a community that will provide the support you want.

  http://social.technet.Microsoft.com/forums/en-us/category/w7itpro

  Thank you.

• I can't start a desktop connection remote with my file server, but I can't get to my domain controller. Other computers on the network can initiate together.

  Using server 2003 as DC and server 2003 as a FS. Problem computer running windows 7 upgraded to vista professional. I can open a desktop session with the domain controller remotely, but I can't launch with the fs. Other computers on the domain have no problem with a server opening. I have access to shared folders on the MSDS via LAN and can ping the fs. Also can not use MySQL on the fs with this computer. FS cannot launch the Office with the computer problem remotely but can with others.

  Hi Gary,.

  Thanks for posting in the Microsoft Community.

  The question you posted would be better suited in the TechNet Forums; We recommend that you post your question in the TechNet Forums to get help:

  http://social.technet.Microsoft.com/forums/en-us/smallbusinessserver/threads

  If you need Windows guru, do not hesitate to post your questions and we will be happy to help you.

• To connect to other computers on the network

  Is it possible to connect to other computers on my network through the slate of 7 (laptop)?

  Can take a look at Splashtop2 in the game store.  Worked great in webOS, should be just as good in Android.

  WyreNut