Need help for installation BIApps

Similar Questions

• Need help for optical safety circuit.

  I buy these parts and prototype with real components, but since I multisim, I thought it would be nice to create the circuit and maybe work through issues I can practically.

  I need a circuit that takes 120 VCA, generates 5 VDC and 1.5Vdc power of optical transmitter and receiver.  I actually use a data port because he has great range and is pretty cheap.  Rather than send the binary code well I just send a light stead that is broken or not broken through doors and windows in my house.  Then the receiver sees this as an entry and order a relay.

  I tried several voltage regulators that come with multisim, but I get an error of execution of my circuit.  Really I can't the 120 VAC to power levels necessary for the functioning of the optics.

  Otherwise I might want to run on a system 120Vdc with battery backup, so throw a 120Vdc up to 20 v DC switching power supply - but I have not found a SMP in the library which takes 120 as input and as output 20.

  Basic plan: 120VAC source-> transform to 24Vac-> Full bridge rectifier to ~ 20 v DC-> voltage capacitor filter on the input of two voltage regulators (1 to 5 VDC, 1 to 1.5Vdc) - then circuit since the two power supply of the transmitter and the receiver.

  I just need help for 5V and 1.5V, from there, I know that the real world circuit will work component tests already carried out.  Thanks for reading.

  I didn't Multism so I can't advise you on the compatible models. I ran the model on semiconductors with slight modifications of format on my SPICE simulator based on Berkeley Spice 3f5. I had to change the format of model resistance semiconductors appeal but has not changed any values.

  The output of your power supply circuit 3 (with 5 V, not the 1.5 V regulator regulator) was 4.99995 V.

  There are a few messages about changing templates published for compatibility Multisim woth. You can search those to see if there are any suggestions on what you'll need to fix in the model.

  Lynn

• I need help for the upgrade of my current system.

  I need help for the upgrade of my current system.

  I have SBS 2008 with (Exch 2007, SQL 2005, Sharepoint, backupexec 2010 for sbs) licenses.

  I want to make the larger environment using the following:

  (1) apply Virtualization

  (2) apply to the failover process (clustering)

  "(3) the environment must support adding server terminal server, ERP server, exchange server, domain controller, backup manager.

  Storage 4) that supports Raid (1 and 5)

  UTM excellent 6) that supports (SSL VPN, VPN Global)

  suitable backup solution 7)

  (8) good antivirus for clients

  my questions:

  (1) can you provide me with a good design for this environment

  (2) should I choose what operating system:

  Microsoft datacenter or company

  I know datacenter provide us the unlimited VM but needs per processor license

  so if I have two Grouped servers I want to buy 4 licenses

  and just 4 VMs per company license... to say that we have two servers and maintain 8 vms so wat happened if 1 goes down... How can I migrate the 4 virtual machines on the server failed to another server group... ? should I buy enterprise license?

  (3) if I get the SAN storage for data... How can I save this storage... should I get another SAN?

  (4) how can I upgrade SBS stad single server (windows standrad) without losing the licenses as Exch 2007, SQL 2005, sharepoint.is it a must to buy an edition full std server or there is a way to upgrade (license wise, I mean)?

  (5) what about win2k8 license for VM:

  lets say we have physical that has windows license so that enough to have windows for VM or should I buy windows for VM licenses?

  (6) can I use backExec license for SBS with windows 2008 standard

  (7) who better to virtualization AMD or INTEL

  (8) hyper V or VMware?

  (9) what of Microsoft data protection Manager... is this good?

  (10) what virtual machine manager? What are the benefites keys

  Thanks in advance

  Hello AnasAI,

  You can find the Server forums on TechNet support, please create a new post at the following link:

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer/

• I need help for activation of the real administrator account.

  I have a problem with Adobe reader 9 standard, Adobe customer service asked the unhide real administrator account before you can continue to help me.

  I need help for that.

  http://www.Vistax64.com/tutorials/67567-administrator-account.html

  http://www.howtogeek.com/HOWTO/Windows-Vista/enable-the-hidden-administrator-account-on-Windows-Vista/

  Read the above info.

  See you soon. Mick Murphy - Microsoft partner

• I need help for my reader to USB drive on my windows 10 ACER?

  I need help for my reader to USB stick on my chrome windows 10 plug ins acer. Can you help me?

  What Adobe application that you use?

  This is the Adobe Media Encoder forum, and you did not mention anything on this subject. If you can let us know what Adobe application, you need help, we can help you make the right forum.

  Thank you

  Regalo

• Hello, I need help for cancel the payment on my adobe account.

  Hello, I need help for cancel the payment on my adobe account. I'm from Peru, Im paying a monthly fee as a student. Help, please...

  Cancel your membership creative cloud

• Hello, need help for Adobe Reader DC playing animation files that are specified in the pdf output by script Latex Beamer. My Adobe Reader DC refuse to open any format that I gave him.  Thank you very much

  Hello, need help for Adobe Reader DC playing animation files that are specified in the pdf output by script Latex Beamer. My Adobe Reader DC refuse to open any format that I gave him.  Thank you very much

  Hey ihorl18351266,

  Please note that you can open PDF files using only the CD player. Any other format will not be supported by the software.

  Kind regards

  Ana Maria

• Installation of the elements 11 on Mac. Need help with installation error "Setup wants to make changes.

  Installation of items 11 Mac 10.8.2. Need help with Setup error: installation wants to make changes. Type your password to allow this. "After entering the Adobe password, nothing happens.  Locked for more than installation.  Any ideas?  Phone support Adobe couldn't help.

  Just prior to leaving changes (installation in this case) is done on the Mac OS application password & it must be the password for Mac system. This password is the native guest of the system clean & accept the password only. Please make sure that it's the right password (all/admin rights) and the game should work.

• I need help for Adobe Flash Player, please!

  I've been on several site trying to play games or watch videos (YouTube, for example) and get an error message saying that I need to install Adobe Flash Player in order to play/view.  I did this several times and currently have 11 ActiveX of Flash Player and Flash Player 11 Plugin.  That I do because it still doesn't let me see the video or play games.

  PLEASE HELP ME!

  Additional information: I found myself just download Google Chrome (but don't like) and do not have the same problem.  So, it happens only when I'm doing all this on Internet Explorer 9.

  Flash Player Help. Installation problems | Flash Player | Windows

  Mylenium

• Need help with installation on Photosmart C7280 all-in-one

  I had my printer is installed and has been using the printer for 3 wireless laptops in my house.  Now, I can't even find my backup drive, so I have need help with downloading the software to use my printer and also get to use wireless.   I don't know what happened, but the fax for this printer is listed, but not the printer itself.   Help, please!

  Click here to download the software for your printer:

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?product=3204785 & LC = on & CC = US & DLC = in & lang = to & CC = US

  has chosen the appropriate operating system that corresponds to your computer and download the full software features.

• Tecra R840 - need help for installing the SSD

  Hello

  Sorry, again, but I really need help with that?
  My new ssd (arriving in a few days) is a Plextor M5P which is 7 mm thick! My Tecra R840-16J have a thickness 9.5 mm HDD and what I've seen is no caddy!
  I would be grateful all the tricks for installing the ssd drive in my Tecra!

  Thanks for your time,

  Paulo

  Hello Paulo

  As far as I know that some models are available with drive HARD and some with SSD these models with SSD have small SSD support. SSD is fixed by 4 screws in this medium.

  I put t really know how to help you now. Maybe you should contact the nearest Toshiba service provider and ask for help. I think they can check the part number of this door - or maybe order one for you.

• Re: Need help for the restoration of the system

  Hi, I need help!

  I recently bought a Toshiba Satellite. I had some problems when trying to install some programs, some seem to fail. I wanted to clean the computer with system restore disc, only to find a record of 32-bit to a 64-bit computer.
  There is a repair of the setting system installed on the computer but it does not work, when I put it on disk, files, it cannot be opened.

  I can restore the system somehow repair; It must have been damaged by a virus. It should come with a big warning that the disk is not compatible!

  I have burned one day drive the first if I d just so you know! Any advice?

  Hello

  At first, I must say that you should tell us what model of laptop you have exactly.

  I put t know what cell phone you have and what you have with her, but in fact, it's that many laptops come with preinstalled OS 64-bit and 32-bit version on DVD.

  In this case, you must create own 64 bit preinstalled use Toshiba recovery media creator recovery DVDs. Alternatively, you can install 64-bit without DVD disk with HARD drive recovery option > http://aps2.toshiba-tro.de/kb0/HTD9102IR0000R01.htm
  Of course, this will not work if you didn't change the factory settings.
  Try if it will work for you.

  At the end I would say that what I wrote is detailed described in the document s user manuals but I presume that you didn t read it, right?

• Need help for reading in parallel on the same interface and writing XNET

  Hello. I need help to configure CAN interface to write and read from the same interface.

  I use NI PXI-8513/2. I use CAN1 as interface.

  My had TO send status messages CAN every 100ms. I have to read in order to return akntoowlege to keep DUT CAN interface happy and not make mistakes.

  So, I want to open Strim Session and readall frames in the loop. At the same time, I need to be able to write in a frame HAD at the time...

  I only need to read one picture at a time too, but since I know the ID, I can pull it from the stream.

  What I'm confusing all is how to put in place the same CAN1 interface to be able to write and read in parallel.

  I think I would get errors that interface is already in use.

  Since I'm new to CAN, I was read and write only when necessary. But, sometimes I was getting errors on my messages. Sometimes I get message, sometimes miss me. But, when I run CAN test criminal as sniffer he sends and written every time. I was told it's because it recognizes all messages.

  I opened to suggestions of how best to implement the interface.

  I guess I can use CAN2 and separator to work around this problem, but I would use an interface if possible.

  Thank you

  Hi Rus,

  The XNET hadrware takes care of most of the low level of detials for you. The reading and writing of the circuits are both connected to the bus at any time. When you write to the hardware it will try to put a frame on the bus at the first opportunity he can. If the frame loses arbitration material re - will attempt to send the frame up is successful. Reception equipment monitor activity on the bus, regardless of what it conveys. The material received will usually throw a framework that was sent by communication equipment, but there is an Echo property pass to circumvent this behavior too.

  Take a look at the example of the expedition: MAY-> NI - XNET-> Sessions-> multiple Sessions Intro-> CAN even exit entry framework Port unique Point.vi. Keep in mind that this example you will need to use a second CAN interface to recognize frames, it transmits. I would recoment against the example CAN output Frame Single Point which would mimic your ECU if you choose a type of cyclic frame running this example.

• I Iconia Tab A500, running 3.0, need help for upgrade by using a microsd card, got Acer download update

  I Iconia Tab A500 running 3.0, need help update, I downloaded the entire updaes list in the supprt of acer, all versions, 3.0, 3.1, 3.2 and 4., I read on the acer support somewhere I can use a microSD card to update my device, as acer provides automatically, when I try it says 'poor network connection '. moving instead of anthoer. ", I have to update all the updates that are listed, or can I only update, using the 4. 0? to get the last known update. I also downloaded, 'Documents, applications, drivers, patches and O.S... How do I intsaller all these updates, I think that running the lowest version available, please help me... Thank you in advance.

  There are some instructions step by step on the site, but basically you check out the file "update.zip" download, copy to the root of a FAT32 formatted microSD card, then start in recovery mode (press one of the volume buttons [which it depends if you are landscape or portrait mode] and hold, then the power press and hold). From there, you can choose to update in the zip file it finds on the map.

  It is important before you have the correct version of the update, it's different for different regions of the world, and you will not be able to upgrade the (for example) Brazil version from the US site.

• [SOLVED] I need help for Shared Documents and Documents on my computer XP Home

  I need help with my shared Documents and other folders on my computer. I have an administrator account. My son has a limited access account.

  I clicked on the option 'make my private files and folders '.  His file was renamed to Documents now my shared Documents. It's just my account.

  I tried to undo what I did. I tried everything (I mean everything) has proposed to do online.

  First of all, I logged in Safemode administrator account. I went to the Documents folder, and I've added the Administrators group and click full control.

  Then I restored system a few weeks before. Then, I went to http://computers.douglasthrift.net/winxpfaq/#faq3_shared_documents and did everything.

  None of them worked. I did so much, that I don't remember.

  Then, I found that the registry key for the Shared Documents lacked in the MUi cache. @shell32.dll,-21785. I entered, but after I rebooted a few times, he disappeared. I have to hurt... In addition to this. Now I face a different problem. I don't know it is normal but when I login my account and click on

  My computer, I see Documents of my name and the name of my son in addition to Documents (Shared Documents).

  When I save a new file in the My Documents folder, it is automatically created in the folder of Documents of my name, too. I can't delete them because they are system folders. I crossed my registry keys in the MUI cache and discovered that 4 of them did not exist in other accounts.

  @shell32.dll,-21792; 21793; 21794; 21795 (%, etc. of music of % documents). I don't know if I can delete them or not.

  I'm not an expert in computers. I'm sorry that it is very long.  I hope someone can help me. Thank you.

  Hello

  I suggest you follow the troubleshooting steps and check if this solves the problem on your computer.

  Method:

  Ra SFC scan to search for the missing or corrupt files that can cause this problem.

  Of file system (CFS) when checking that all the Windows XP system files are intact and not altered, changed or damaged.

  a. Click Start, click programs, accessories, command prompt principally made.

  b. in the type in the following command prompt window and press ENTER:

  sfc/scannow

  If you are prompted to insert the Windows XP disc, load the disc of Windows XP on the CD drive on your computer.

  Once the scan finished restart your computer and test to see if the problem you are experiencing is resolved or not.

  Reference: http://www.microsoft.com/resources/documentation/windows/xp/all/proddocs/en-us/system_file_checker.mspx?mfr=true

  I hope this information helps. Please get back to us if you have any other questions on this subject.