Need help! The site reappears at the opening and then turns off!

Similar Questions

• my iphone 5 works if connected to my charger, when I unplug it it stays on for a minute and then turns off, I can activate it after that but it turns off again. you wonder if it's my battery. I have already restored the phone, but it did not work. Help

  my iphone 5 works if connected to my charger, when I unplug it it stays on for a minute and then turns off, I can activate it after that but it turns off again. you wonder if it's my battery. I have already restored the phone, but it did not work. Help

  Most likely, the battery is broken. With AppleCare +, a replacement of the battery is free. However, without AppleCare +, a replacement battery will cost $79.

  Apple-Support - iPhone - battery and power: https://www.apple.com/support/iphone/repair/battery-power/

• 23 Pallvion all-in-one: the Logo screen then turns off 10 Windows

  I have upgraded to Windows 10 awhile ogo and so far my computer was working fine. Then, I came across a virus if sort so I decided to simply reset my computer. When I tried to reset it, it would be stuck on 1%. So, I then turned my computer off and when I turned it on the logo appeared for about 15 seconds and then turns off. I almost tried everything. I t doesn't let me not reset again without a disc I don't have. And it says there is an error when I try to refresh the pc. I'm stuck and need help fast!

  I didn't say it was the only way, but the most logical.  There are other choices.  You can use the set of diskettes of recovery that you made when the computer was new.  You can use a borrowed from Windows 8 or 8.1 Windows installation disk, but it would be necessary to match the windows that came from HP that was installed.  You could buy or borrow a disc 10 Windows installation to run.  On this day and the social environment, it is rare that you do not find a friend to do the free Windows 10 disc for you, however.

  If these choices do not meet your approval, then I guess there is a problem.

• mouse Bluetrack 4000 light turns on normally and then turns off on problem is not the battery

  mouse Bluetrack 4000 light turns on normally and then turns off on problem is not the battery.

  Hello

  1. your wireless mouse does not work?

   
  I suggest that you follow all the steps of the article which will help you solve the problem
   

  Troubleshoot a wireless mouse that does not correctly
  http://support.Microsoft.com/kb/321122

• After turning on my wireless keyboard led green lights, then begins to blink, and then turns off. The batteries are fresh.

  After turning on my wireless keyboard led green lights, then begins to blink, and then turns off. The batteries are fresh.

  Possible explanation.  It is likely that batteries, so fresh, can be irregular in size.   The uncertain connection would therefore tend to lead to a failure to blink and you declare.   Read my thing...

  Batteries.

• my laptop connects to an external monitor at the start, but then turns off I have xp sp3 with anyone who can help

  When I boot my laptop with an external monitor or TV it showws the logo of windows but when it starts good happening to and does not display the message no signal

  It allows to work with vista but uninstalled vist because I do not love

  is this a fault of software with xp

  Hello

  · What is the number and the model of the laptop?

  · What is the exact error message that you receive with error code if any?

  Check out the links and then re - configure multiple monitor and check if that helps.

  Hardware requirements for the display Support in Windows XP: http://support.microsoft.com/kb/296538

  How to configure and use multiple monitors in Windows XP: http://support.microsoft.com/kb/307873

• Sum of columns together in the responses, and then calculated off summary columns

  I have three questions answers (with 4 columns) that I have gathered the results for:

  Four columns are: campaign # promoted # Respones, # Respones promoted

  Query 1:

  Campaign, # promoted, 0, 0

  Query 2:

  Campaign responses #, 0, 0,.

  Query 3:

  Campaign, 0, 0, # promoted Respones

  My query returns the following (assuming that the campaign code is ABC) 3 rows:

  Campaign of	# Promoted	# Responses	# Promoted answers
  ABC	100	0	0
  ABC	0	12	0
  ABC	0	0	9

  I want to put in place so that it adds campaign to get a row of results as follows:

  Campaign of	# Promoted	# Responses	# Promoted answers
  ABC	100	12	9

  I can get this result using the conversion to a PivotTable (won't go thought road if possible because I have other calculations that I need to add).   Once I get this summary to a single row result I then do a few such analyses that create:

  1. Response % (Respones # / # promoted)
  2. Promoted to the rank of % (# promoted answers / # promoted)

  When I add the calculatinos to the percentages to the United query I get null or zero for my results.   I used the Add button to insert a calcuation and then I used the following formula: saw_2 / saw_3

  Here's what I would preferably:

  1. Sum of answers (not a pivot table) Table columns.
  2. Add columns calculated at United query that will produce results based on the combined pivot columns
  3. If I use the PivotTable, and then how to get the values calculated for work

  Thank you...

  Ben,

  Try to use the rule of aggregation on the columns in the Table view and see if that makes a difference.

  I just tried this and the SUM of each of the criteria provided the results I wanted, which in turn you are looking for.

  If nothing works for you send me the screenshot of what you are trying to do at vijaybez at gmail and I can understand what is happening properly...

• NB550D boots in black of the screen and cannot turn off even

  I had my NB550D for only less than a month. I've updated the memory to 2 GB and the Op to Home Premium system, but nothing else. It's on auto update on security issues, and I remained with the McAfee protection which was pre-installed (and paid for a year).

  All is well until a few days ago when you turn on, I just got black screen. Could hear the fan and disc well. Finally pressed the power button, nothing changed, has waited a bit, pressed again and it is off. When I pressed once again he came as usual. Used several times in the last two days and has been very well. Now today I get black screen again and can hear the fan. When subsequently, I pressed switch, I heard snoring disk but still black screen. Since then, tried pressing on/off switch from time to time but no change at all - can't turn off!

  Anyone has any suggestions please?

  Flingel

  I read in another forum that the answer must take the battery (having already taken the sector) so it will die and then press on and press and hold power for 30 to 60 seconds. I had nothing urgent to do let him die naturally when the battery is missed rather than take out the battery when it was on. Then, I held the power button for 60 seconds, plugged in and turned on. It starts very well now, but of course I don't know a) the question of whether it is because I held the power button in 60 seconds and b) on the question of if same thing will happen again, so if anyone has experience of this behavior, I would be grateful for comment.

  Thank you

  Flingel

• iPad does not turn on/just the Apple logo and then turn off again

  I have an iPad, 4th generation, 64 GB with WiFi and cell phone, it is only 3 years and suddenly I can't turn on the iPad. When he started to act up it would freeze upwards with no icons or the button "home" in response, still on the screen, that he was freezing. I was able to restart it with the top button and it would work for 10-15 minutes and freeze no icons or the button being sensitive at home. I could do a hard reboot and when I rebooted, it would work again for 5-15 minutes and freeze once more. This was during a week and now it does not restart. When I try to turn on with the button at the top of the Apple logo appears, remains on the screen for about 3-5 minutes (no progress bar) and turns off again with no other screen appearing. I tried to find a solution online without success. Anyone have any suggestions for a fix for the iPad? I would appreciate any ideas that anyone could have.

  If the unit starts to turn back on the wide, then it seems that if you have a hardware problem. If the unit is charged and a reset will produce only a short period of service, then it is a hardware error or an error in battery, which would be also considered to be material. You can try to restore the device to factory and test without adding any additional content. If it still fails, then make an appointment at the Genius Bar watching him.

  Use iTunes to restore your iPhone, iPad or iPod settings - Apple Support

• treble buttons to quick launch keeps flashing on the screen and wifi turn off voltage

  HP pavilion dv8 quick launch button treble keeps flashing on the screen and now and again the wifi turns off and I have to keep back on.

  Hello

  Unless you have already done so, download and apply the firmware update for the capacitive strip on the link below which is intended to fix this particular problem.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-96360-1&cc=us&DLC=en&LC=en&OS=4063&product=4034201&sw_lang=

  After the update has been applied, restart the laptop.

  Kind regards

  DP - K

• Which adapter to use on hard drive to get the data and images turned off before replacing the motherboard?

  I have a HP G61-429WM, product WA961UA #ABA number. Windows7 operating system. It was abandoned and cracked the screen. I replaced the screen, it then booted up once or twice, and then began to not initialize. During this period, I noticed a crack in the lower shell into the Jack of the battery. Do you have a fairly long conversation with the support, the end result = send to paid the replacement of the main card or buy the same Board and fix it myself. He said that all the data on the disk wouldn't be there when I returned. It was also mentioned that the reader could be removed and a usb adapter could be used on the disk to retrieve data before the reader gets erased due to the relocation of the card.

  Everyone would like to recommend a usb adapter to do? I will buy one, I want to just make sure it is right for the type of drive in this unit.

  Thanks in advance,

  Sylvia

  DavidD56.

  I've used this for any type of reader:http://www.newegg.com/Product/Product.aspx?Item=N82E16812232002

  But, you can perform a single completed unit:

  http://www.Newegg.com/product/product.aspx?item=N82E16812123312

• Drive not opening - short gray screen and then turn off.

  Installed and re-installed 5 times. not expert enough to want to go and mess with registry keys - using the free download for years on PC private and a pro at work version. Seiously turns off after the last few weeks.

  I can't believe that they have not yet released a patch. I to we'll now probably, turn off acrobat then never return - fantastic marketing opportunity for smart people if they make the knowledge of it.

  They are blissfully unaware or they trawl fishing site and who use in their product design?

  Three things to try...

  1. Using Windows Explorer navigate to C:\Program Files (x 86) \Adobe\Reader 11.0\Reader, and then double-click Eula.exe and accept the license agreement
  2. You can open Adobe Reader by itself?  If so, try to disable the Protected Mode [Edit |] Preferences | (Improved) security].
  3. It might even be a malware problem; See http://helpx.adobe.com/acrobat/kb/reader-core-dll-error.html

• Why the screen "post preview" in flash cs5 shows the part of the animation and then turns blank?

  Hi I'm creating animation frame by frame in photoshop.

  I import photoshop files into flash using

  FILE > IMPORT > IMPORT TO STAGE

  I used to be able to preview or 'test line' my movie easily by clicking on:

  FILE > PUBLISH PREVIEW > FLASH

  I could watch the animation in a loop and see where improvements are needed. Now, flash struggles a lot with the files, takes a long time to load the preview, when that happens, it shows me maybe a third of the animation, running on empty and behaves as if all my frames are completely empty. I can't see on my main work no more later.

  Anyone know what is happening? I keep restarting flash but the same problem persists.

  Thanks in advance for any help or suggestion

  It's more 100megs of images, then you are probably hitting a limit of flash cs5/system.

  are you using a channel alpha and overlay of some of these pictures on another?

• I have an I Phone 5 for a month issues and have stay connected to WiFi at home, it shows plugged in to the phone, but is not, I have to turn off WiFi on the phone and then turn it back on and it's ok for a day or two, I reset

  Stay connected to home Wi - Fi issues

  If your iPhone, iPad or iPod touch connects to a Wi - Fi - Apple Support network

• Try power upward and he would keep a black screen for a few seconds then turn off and turn on and repeat until I've done a hard stop. I got a message on the svchost.exe

  Original title: help - csvhost.exe and problems to start

  My sons laptop has problems - try to turn on and it would maintain a black screen for a few seconds and then turned off and turn and repeat until I've done a hard stop.  I am able to navigate to the top after repeated attempts.  I could take a quick and complete hard drive test and it passed... Finally, I restored to factory and spent the last 8 hours going through the update process.  It works fine and restart without problems until recently - I followed the instructions to reboot to perform an update, but he had served in the "shutting down" mode for almost an hour I did a firm hard down.  It took a few attempts so he could begin after that, and when I did I had a message on the svchost.exe and thought that might have something to with him... found a site that has a download that is supposed to fix errors and am curious if that is recommended or whether there is another solution or possible make my misfortunes.  The site is: http://www.exe-error-advisor.com/svchost-exe.  I don't know what's happening - the computer works very well when it turns - to be fair, I did also made an update of "HP Total Care Advisor" who has nothing and after I rebooted I could not make it work... "HP Advisor has stopped working"

  Any ideas or advice?

  replied in the other thread

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-system/help-svchostexe-and-problems-booting/cd6ef667-7833-4f34-B976-ffded620a208