Need help to access my MTU settings
, I played Xbox Live for 9 months and have not had any problems with it until my Xbox 360 broke down. I had fixed it so its place and currently under way and I can't use Xbox Live more. I get a message saying my MTU is too low and I need to put at least 1364. I spent some time on this and I ask for all possible assistance. My problem is accessing the MTU settings. I use a WRT160N and I used the web address http://192.168.1.1/ However, when he talks about the box asking username and password I'm stuck. I tried everything, I left as empty user name and the password as an administrator. But it does not work. In other forums, I've seen try the username and the password under the two admin but that did not work or the other. After three attempts, it goes to a red page saying 401 Unauthorized. I disabled my firewall, reset my router and still nothing. If you have a solution to this I'd be very happy!
Thank you!
For the model No, you, there is no username and password is "admin" in the lower case.
The reason why the admin does more work as router password because you have setup a router password, not knowing, in the first time install you your router... If you remember the router password when you used all first your installation CD to install your router then enter this password else you need to reset your router and the re - configure...
To reset the router press and hold the reset button for 30 seconds... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now re - configure your router...
* Not all the settings above from the computer that is connected to the router.
Tags: Linksys Routers
Similar Questions
-
Need help to define the best settings of the picture on my TV 32RL938
I recently bought a Toshiba led TV 32RL938 I need help for my photos, anyone help me put the best images for movies and channels... contrast, brightness, standard, dynamic...
Each new product is document s user manuals. What you need is described here, so I think that you should not waste your time here but check this in manuals and test it on your TV.
You must learn how it works.
-
Need help to access the internal network via VPN on ASA5505 8.4 (1)
Recently, I upgraded my ASA5055 from 8.02 to 8.4 and since I have updated to the new version I can access my home network is no longer through the VPN. I can connect to the VPN with no problems however I can no longer ping or you connect to my network of 10.0. Someone would be kind enough to look at my config and tell me what needs to be added to make it work? In my old config, I had a statement of NAT for VPN that is no longer here.
I also wanted to configure WebVPN to work as well, and this is something that I've never been able to understand. Is it also possible that I can be on my 20.0 network and connect to the VPN and access 10.0 as well? When it is connected to my network of 20.0 I'm not received credentials to connect to the VPN. I would be grateful if someone can help out me. The major part of this is the first part of this question.
My configuration:
ASA Version 8.4 (1)
!
ASA5505 hostname
domain xxxxxxxx.dyndns.org
enable encrypted password xxxxxxxxxxxx
xxxxxxxxxxxxxxx encrypted passwd
names of
nameserver 192.168.10.2
Office of name 192.168.10.3
name Canon 192.168.10.5
name 192.168.10.6 mvix
name 192.168.10.7 xbox
name 192.168.10.8 dvr
name 192.168.10.9 bluray
name 192.168.10.10 lcd
name 192.168.10.11 mp620
name 192.168.10.12 kayla
name 192.168.1.1 asa5505
name 192.168.1.2 ap1
name 192.168.10.4 mvix2
name 192.168.10.13 lcd2
name 192.168.10.14 dvr2
!
interface Vlan1
nameif management
security-level 100
IP address asa5505 255.255.255.248
management only
!
interface Vlan2
0050.8db6.8287 Mac address
nameif outside
security-level 0
IP address dhcp setroute
!
interface Vlan10
nameif private
security-level 100
IP 192.168.10.1 255.255.255.224
!
interface Vlan20
nameif Public
security-level 100
IP 192.168.20.1 255.255.255.224
!
interface Ethernet0/0
Description pointing to WAN
switchport access vlan 2
!
interface Ethernet0/1
Uplink port Linksys 12 description
switchport access vlan 10
!
interface Ethernet0/2
Description Server 192.168.10.2/27
switchport access vlan 10
!
interface Ethernet0/3
Uplink Eth1 management description
!
interface Ethernet0/4
switchport access vlan 30
!
interface Ethernet0/5
switchport access vlan 30
!
interface Ethernet0/6
switchport access vlan 30
!
interface Ethernet0/7
Description of Cisco 1200 Access Point
switchport trunk allowed vlan 1,10,20
switchport trunk vlan 1 native
switchport mode trunk
!
Banner motd users only, all others must disconnect now!
boot system Disk0: / asa841 - k8.bin
passive FTP mode
clock timezone PST - 8
clock summer-time recurring PDT
DNS server-group DefaultDNS
domain xxxxxxx.dyndns.org
network object obj - 192.168.50.0
192.168.50.0 subnet 255.255.255.0
Server network objects
host 192.168.10.2
network object obj - 192.168.10.0
192.168.10.0 subnet 255.255.255.224
network object obj - 192.168.20.0
subnet 192.168.20.0 255.255.255.224
network server-01 object
host 192.168.10.2
network server-02 object
host 192.168.10.2
xbox network object
Home 192.168.10.7
xbox-01 network object
Home 192.168.10.7
xbox-02 network object
Home 192.168.10.7
xbox-03 network object
Home 192.168.10.7
xbox-04 network object
Home 192.168.10.7
network server-03 object
host 192.168.10.2
network server-04 object
host 192.168.10.2
network server-05 object
host 192.168.10.2
Desktop Network object
host 192.168.10.3
kayla network object
Home 192.168.10.12
Home_VPN_splitTunnelAcl list standard access allowed 192.168.10.0 255.255.255.224
outside_access_in list extended access permit tcp any any eq 3389
outside_access_in list extended access permit tcp any any eq 2325
outside_access_in list extended access permit tcp any eq ftp server object
outside_access_in list extended access permit tcp any any eq 5851
outside_access_in list extended access udp allowed any any eq 5850
outside_access_in list extended access permit tcp any any eq pptp
outside_access_in list extended access udp allowed any any eq syslog
outside_access_in list extended access udp allowed any any eq 88
outside_access_in list extended access udp allowed any any eq 3074
outside_access_in list extended access permit tcp any any eq 3074
outside_access_in list extended access permit tcp any any eq field
outside_access_in list extended access udp allowed any any eq field
outside_access_in list extended access permitted tcp everything any https eq
outside_access_in list extended access permit tcp any eq ssh server object
outside_access_in list extended access permit tcp any any eq 2322
outside_access_in list extended access permit tcp any any eq 5900
outside_access_in list extended access permit icmp any any echo response
outside_access_in list extended access permit icmp any any source-quench
outside_access_in list extended access allow all unreachable icmp
outside_access_in list extended access permit icmp any one time exceed
outside_access_in list extended access udp allowed any any eq 5852
KaileY_splitTunnelAcl list standard access allowed 192.168.10.0 255.255.255.224
pager lines 24
Enable logging
timestamp of the record
exploitation forest-size of the buffer of 36000
logging warnings put in buffered memory
recording of debug trap
asdm of logging of information
address record [email protected] / * /
exploitation forest-address recipient [email protected] / * / level of errors
Management Server host forest
MTU 1500 management
Outside 1500 MTU
MTU 1500 private
MTU 1500 Public
local pool IPPOOL 192.168.50.2 - 192.168.50.10 255.255.255.0 IP mask
local pool VPN_POOL 192.168.100.2 - 192.168.100.10 255.255.255.0 IP mask
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow all outside
ASDM image disk0: / asdm - 641.bin
don't allow no asdm history
ARP timeout 14400
!
Server network objects
NAT (private, foreign) static tcp ftp 5851 service interface
network object obj - 192.168.10.0
NAT (private, foreign) dynamic interface
network object obj - 192.168.20.0
NAT (outside) dynamic public interface
network server-01 object
NAT (private, outside) interface static 2325 2325 tcp service
network server-02 object
NAT (private, outside) interface static udp syslog syslog service
xbox network object
NAT (private, outside) interface static service udp 88 88
xbox-01 network object
NAT (private, outside) interface static service udp 3074-3074
xbox-02 network object
NAT (private, outside) interface static service tcp 3074-3074
xbox-03 network object
NAT (private, outside) interface static tcp domain domain service
xbox-04 network object
field of the udp NAT (private, foreign) of the static interface function
network server-03 object
NAT (private, outside) interface static tcp https https service
network server-04 object
Static NAT (private, outside) interface service tcp ssh 2322
network server-05 object
NAT (private, outside) interface static 5900 5900 tcp service
Desktop Network object
NAT (private, outside) interface static service tcp 3389 3389
kayla network object
NAT (private, outside) interface static service udp 5852 5852
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
AAA authentication enable LOCAL console
AAA authentication http LOCAL console
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
Enable http server
http 192.168.1.0 255.255.255.248 management
redirect http outside 80
location of SNMP server on the Office floor
SNMP Server contact [email protected] / * /
Community SNMP-server
Server enable SNMP traps snmp authentication linkup, linkdown cold start
No vpn sysopt connection permit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto-map dynamic outside_dyn_map pfs set 20 Group1
Crypto-map dynamic outside_dyn_map 20 set transform-set ESP-3DES-SHA ikev1
life together - the association of security crypto dynamic-map outside_dyn_map 20 28800 seconds
Crypto-map dynamic outside_dyn_map 20 kilobytes of life together - the association of safety 4608000
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
Crypto ikev1 allow outside
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 192.168.1.0 255.255.255.248 management
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 30
Console timeout 30
access to administration management
dhcpd dns 24.205.1.14 66.215.64.14
dhcpd ping_timeout 750
dhcpd field xxxxxxxx.dyndns.org
dhcpd outside auto_config
!
dhcpd manage 192.168.1.4 - 192.168.1.5
dhcpd enable management
!
dhcpd address private 192.168.10.20 - 192.168.10.30
enable private dhcpd
!
dhcpd 192.168.20.2 public address - 192.168.20.30
dhcpd enable Public
!
a basic threat threat detection
statistical threat detection port
Statistical threat detection Protocol
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Server NTP 192.43.244.18
Server NTP 129.6.15.28
WebVPN
internal Home_VPN group strategy
attributes of Group Policy Home_VPN
value of 8.8.8.8 DNS Server 4.2.2.2
Ikev1 VPN-tunnel-Protocol without ssl-client
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Home_VPN_splitTunnelAcl
value by default-field www.xxxxxx.com
the address value IPPOOL pools
WebVPN
the value of the URL - list ClientlessBookmark
political group internal kikou
group attributes political kikou
value of 8.8.8.8 DNS Server 4.2.2.2
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list KaileY_splitTunnelAcl
XXXXXXX.dyndns.org value by default-field
username scottrog encrypted password privilege 0 xxxxxxxxxxxxxx
user_name john encrypted password privilege 0 xxxxxxxxxxxxxxx
username joek encrypted password privilege 0 xxxxxxxxxxxx
eostrike encrypted xxxxxxxxxxxx privilege 15 password username
username almostsi encrypted password privilege 0 xxxxxxxxxxxxxx
username ezdelarosa password xxxxxxxxxxxxxxencrypted privilege 0
type tunnel-group Home_VPN remote access
attributes global-tunnel-group Home_VPN
IPPOOL address pool
LOCAL authority-server-group
authorization-server-group (outside LOCAL)
Group Policy - by default-Home_VPN
authorization required
IPSec-attributes tunnel-group Home_VPN
IKEv1 pre-shared-key *.
type tunnel-group SSLClientProfile remote access
tunnel-group SSLClientProfile webvpn-attributes
enable SSLVPNClient group-alias
tunnel-group type ClientLESS remote access
tunnel-group kanazoé type remote access
attributes global-tunnel-group kanazoé
address VPN_POOL pool
by default-group-policy kikou
tunnel-group KaileY ipsec-attributes
IKEv1 pre-shared-key *.
by default-group Home_VPN tunnel-Group-map
!
!
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:438ed6084bb3dc956574b1ce83f52b86
: end
ASA5505 #.
Here are the declarations of NAT for your first question:
network object obj - 192.168.100.0
255.255.255.0 subnet 192.168.100.0
NAT (private, foreign) source static obj - 192.168.10.0 obj - 192.168.10.0 destination static obj - 192.168.50.0 obj - 192.168.50.0
NAT (private, foreign) source static obj - 192.168.10.0 obj - 192.168.10.0 destination static obj - 192.168.100.0 obj - 192.168.100.0
And 'clear xlate' after the above and that should fix your first question.
I would check your second question and get back to you shortly.
-
I'd appreciate any help or information that may help me set my Internet Options on my IE LAN settings. The configuration that I need to adjust consists of set the network settings on Auto instead of the designated inputs.
Hi JoseGarza,
You can follow these links to configure the wireless router & check if it helps.
Hope the helps of information.
Please post back and we do know. -
Need help to access family children hotmail accounts
Summary of the issue
My Hotmail service seems to be not available/downPlease provide your address affected:E-mail address is removed from the privacy *.How long have you been unable to sign in?More than a dayAdditional details
I can log into her account and she was not able to receive e-mails from anyone other than me. What should I do?Hi Loren J,.
We checked the account affected and found that his account is currently limited by Windows Live Family Safety. To be able to solve this problem, you need to change its account settings by going to fss.live.com.
Please follow the steps below on how to remove the restriction.
1. connect to http://fss.live.com using the parent account.
2. click Edit settings under the name of the child you want to remove the restriction.
3. click on Contact Management, it is located on the left side of the web page.
4. under management of Contact for the child's name , select the radio button next to the child manages their own contact list.
5. click on the button Save to update the settings.
Once this has been done, please check if it will be able to receive e-mails from his contact list.
Let us know if you need more assistance.
Thank you!
-
Need help to access a different drive
I connected a hard drive in XP on a computer that is running 7. How to restart the computer to run under the XP disc?
Hello
That one disc at a time can be C: and it seems that Windows 7 and XP have been installed
in this way, then you will need to pass the cables then XP will start as C: and, of course, Windows 7
then wouldn't boot.---------------------------
How to set up a Dual Boot Installation with Windows 7 and XP
http://www.SevenForums.com/tutorials/8057-dual-boot-installation-Windows-7-XP.htmlDefinitive dual-booting guide: Windows 7, Linux, Vista and XP step-by-step
http://apcmag.com/the_definitive_dualbooting_guide_linux_vista_and_xp_stepbystep.htmDual Boot computer preinstalled Windows 7 with XP
http://www.howtogeek.com/HOWTO/8790/dual-boot-your-pre-installed-Windows-7-computer-with-XP/----------------------------
How to create a multiple-boot system in Windows XP
http://support.Microsoft.com/kb/306559EasyBCD - free - response of award-winning several NeoSmart Technologies to take control of
your bootloader. EasyBCD extends and rearranges the Windows Vista/Windows 7 BCD bootloader,
and with EasyBCD, almost anything is possible. Install and configure a dual-boot between
Windows 7, Windows Vista, older versions of Windows like XP & 2003, Linux, Ubuntu, BSD,
and Mac OS X is a breeze. You just point & click and EasyBCD does the rest. EasyBCD is free for the
private, non-commercial use.
http://NeoSmart.NET/DL.php?id=1Consult the EasyBCD Forums and support.
http://NeoSmart.NET/forums/I hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">->
-
Need help, limiting access to my children.
I built a computer for my children running Win7 what I'm trying to do so I created a user account for them. I want to make sure when they click their user account that they see ONLY their programs. No start menu to any shortcut for anything whatsoever. However, I want to connect to an administrator account and to see him regularly with all links to the operational services and ECT. I created a user account for them and turnde on parental controls, the issue Im having is I delete a shortcut on the desktop of their account (in this case, the video utility) and enter the admin password, the shortcut is deleted in the two accounts.
Hello
Thanks for posting your query on the Microsoft Community.
According to the description, I understand that you are facing problems with Windows.
I suggest to read the articles below and check if that helps.
Implement family characteristics
Family Safety: frequently asked Questions
I suggest also refer to the article below and check if that helps.
https://TechNet.Microsoft.com/en-us/library/ee623984 (v = ws.10) .aspx
Hope this information helps. Please let us know if you need any other help with Windows in the future. We will be happy to help you.
-
Need help to change the admin settings
I bought a used dell optiplex 755 from a local community college and need to change the admin settings so I can download the programs and files because it deletes every time on restart.
Do you a big favor and restore the computer to its factory settings.
See: http://www.dell.com/support/Article/us/en/19/SLN291879/EN
If for any reason that does not work (for example, the school removed Dell 'restoration' software), go to the Community College of the it Department and ask them nicely to restore the computer to a functional State.
NB: If after restoring to factory State, you have any software "free trial" - any software particularly virus - be sure to uninstall. The free trial period will have expired for a long time and the presence of antivirus software, even if idle, can cause a lot of problems. Most of the antivirus software requires special removal tools provided for free by the Publisher of the antivirus software. For example:
https://service.McAfee.com/FAQDocument.aspx?ID=TS101331
https://support.Norton.com/SP/en/us/home/current/solutions/kb20080710133834EN_EndUserProfile_en_us
-
need help to access nc.windows app.23791
trying to access the lms - LABOR MANAGEMENT SYSTEM for DARDEN ACCESS
-
Need help to change the security settings on my computer.
My computer does not allow me to download anything this either on the net say security settings do not allow this file to download what should I do to change this?
What browser are you using, Internet Explorer, Firefox, or Chrome.
If its IE try this: in IE > tools > Internet Options > Security tab > select Reset all default level areas.
This should reset the security settings and allow you to download files.
-
6224 to 5324 on Embarq 100 MB point needs help of Ethernet on MTU
We run on optical fiber with Embarq on their ethernet point to point service. On the 6224 I MTU normally the default value of 1518, Embarq sets the MTU in their Cisco 3400 to 1546. When they do, we have major problems with traffic, not to complete any work of web pages, or outlook connectivity for most.
When they their MTU on 1510, we have better connectivity, but still experience slowness and the questions on the web page.
Is there a standard for MTU for ethernet 10 MB, because it is the speed of the port.
We spent more than a week, trying different ideas, to get the circuit to the process so Web pages that the actions of prospects more admin, effectively.
I connect the 6224 their Cisco 3400 in their cloud, then a Cisco 3400 on the end, connected to our 5324.
-
Running Windows 7 Professional with XP Mode - need help with access to the XP Mode
Windows 7 Professional and installed XP Mode so I could run my Outlook Express email accounts. I was changing my password xp mode and before I finished putting a new password my computer loses power. Now, I have no way to get xp mode to work (the previous password does not work). Any help on opening the program would help! Thanks advance!
Hello
The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the Windows Virtual PC and XP Mode Forums.
http://social.technet.Microsoft.com/forums/en-us/w7itprovirt/threads
-
Urgent need help with access to the scene.
I want to access the video clips that are nested inside of each other and I want to access the main theater of my project when it was created, but I can't do that with Actionscript 3. How do I access the root of my project?
You can reference the root or the main timeline to use anywhere:
MovieClip (root)
-
Need help to access information on the model after the death of hard drive.
The hard drive on my 13 mid-2010 "MacBook Pro went a few months ago and I intend to replace it with an SSD (and the upgrade of my RAM so I'm here). The thing is, since he's already dead I can't boot my laptop to find the info on the model in order to select the right SSD (and RAM). How can I get this information?
A MacBook Pro 13-inch Mid-2010 will be a model A1278 number and an identifier of model MacBookPro7, 1.
-
need help with access to the administrator account
I know that there is an account on my computer called Administrator. I know because when I type NET USER in CMD it gives me an account named Administrator. When I type in NET USER ADMINISTRATOR cmd, I get: active account number how can I activate this account?
I know that there is an account on my computer called Administrator. I know because when I type NET USER in CMD it gives me an account named Administrator. When I type in NET USER ADMINISTRATOR cmd, I get: active account number how can I activate this account?
Given that the account is already active, you will not have to activate it. Anyway, you can typeNET user administrator / Active: YesWhen you are connected under an administrator account. Note that by using the administrator account gives you exactly the same privileges as any other admin account. There is no difference.
Maybe you are looking for
-
The Windows Installer are not available
Error message:"Failed to start the installer of windows on the local computer. "ERROR 3: the system cannot find the path specified." How can I fix this hole without losing any software or use the recovery disc.Using windows XP on a 3000 satellite.
-
Can't my wireless mouse to work in Windows XP
I installed Windows XP on my Macbook Pro, but I can't figure out how to get my bluetooth mouse works under Windows, even if it works when running Mac OS X, I have installed all the drivers Boot Camp, which doesn't seem to be the problem. Aid online r
-
Firewall Windows does not?
Hey guys,. When I try to access the windows firewall, he invites me to him allow. When I click on the button to activate it, the window hangs for about 30 seconds, then when it thaws, nothing has changed. A way to solve this problem?
-
GlobalEventListener on the events of browser does not (does nothing)
Hello I have read all the post I could find on the global event listeners, but still did not solve my problem. I need to listen to a global event displayed by the default browser (specifically the one displayed when navigation is complete). This wo
-
cancel the services of the Foundation 11.1.1.2 configuration
I tried to $MIDDLEWARE_HOME/EPMSystem11R1/common/config/11.1.2.0/unconfigure.sh , but no window appears as configtool.sh. Need help!