Need router and switches for simple network tips...

Similar Questions

• Configure the DHCP on the router and switch

  Good afternoon

  I'm trying to set up DHCP using CLI on a 2610 router and switch 2950.  With my current config, the host at the end of the switch (set to receive ip via DHCP) does not have anything assigned.  Here are a few shows:

  Router:

  Router_1 #show ip int br
  Interface IP-Address OK?   Method State Protocol
  192.168.10.1 FastEthernet0/0 YES manual up up (leading to pass)
  Serial0/0 YES no not defined administratively down down
  Serial0/1 no YES not defined administratively down down
  Ethernet1/0 YES no not defined administratively down down
  Ethernet1/1 no YES not defined administratively down down
  Ethernet1/2 no YES not defined administratively down down
  Ethernet1/3 no YES not defined administratively down down

  Router_1 #show ip dhcp pool

  Pool acer_pool:
  Brand usage (up/down): 100 / 0
  Size of the subnet (first/next): 0 / 0
  Total addresses: 254
  Rental addresses: 0
  Waiting for the event: no
  subnet 1 is currently in the pool:
  Range of addresses IP of Current index leased addresses
  192.168.10.1 192.168.10.1 - 192.168.10.254 0

  Switch:

  Switch_1 #show ip int br
  Interface IP-Address OK?     Method State Protocol
  Vlan1 unassigned YES NVRAM up up
  FastEthernet0/1 no YES unset upward, upward (leading to the router)
  FastEthernet0/2 not assigned YES unset down down
  FastEthernet0/3 not assigned YES unset down down
  FastEthernet0/4 not assigned YES unset down down
  FastEthernet0/5 not assigned YES unset down down
  FastEthernet0/6 not assigned YES unset down down
  FastEthernet0/7 not assigned YES unset down down
  FastEthernet0/8 not assigned YES unset down down
  FastEthernet0/9 no YES unset down down
  FastEthernet0/10 not assigned YES unset down down
  FastEthernet0/11 no assigned YES unset down down
  FastEthernet0/12 not assigned YES unset down down
  FastEthernet0/13 not assigned YES unset down down
  FastEthernet0/14 not assigned YES unset down down
  FastEthernet0/15 no assigned YES unset down down
  FastEthernet0/16 not assigned YES unset down down
  FastEthernet0/17 no assigned YES unset down down
  FastEthernet0/18 no assigned YES unset down down
  FastEthernet0/19 not assigned YES unset down down
  FastEthernet0/20 not assigned YES unset down down
  FastEthernet0/21 no assigned YES unset down down
  FastEthernet0/22 YES no assigned unset upward, upward
  FastEthernet0/23 not assigned YES unset down down
  FastEthernet0/24 no assigned YES unset down down

  What other info I can provide to solve this problem?

  Thank you.

  I think that you need to configure the router-on-a-stick.

  Post your DHCP configuration.

• Orbi router and satellites for a condominium of 40 units

  I am considering Orbi router and satellites for a condominium of 40 units.

  What are the limits on the number of satellites, and how the energy distribution (which carries the signal from the router to the satellite) on the signal, since it needs to go through a panel of circuit breaker between the router and each satellite?

  I guess all tests (so far) be on the side of the user to a single panel. In the case of joint ownership, each distribution panel is a subgroup of experts of the main breaker box.

  Hello JimLudden

  From what I gather from your question, you think Orbi is a power Extender line? Orbi does not work it on the power line, you can watch these Ko to get a better understanding of what can make the device.

  http://KB.NETGEAR.com/app/answers/detail/A_ID/31031?CID=wmt_netgear_organic

  http://www.downloads.NETGEAR.com/files/GDC/RBK50/RBK50_QSG_EN.PDF?CID=wmt_netgear_organic

  DarrenM

• Wireless network connection - stay connected in our linksys router and switch to a connection TataraTmp

  We have a wireless network connection, but it will not stay connected continuously, it switches to another network, called TataraTmp, and it won't let me delete or reset the settings.  Can someone tell me what it is and how do I get rid of him?

  Thank you

  just uninsralled o2 connection manager and tatara tmp disappeared, so his tied up with the o2 connection manager I did as the connection manager as it shows the use of services to mobile broadband, but I fear its useless if he messes about connect me to my router home as tatara tmp thanks o2

• Routing and switching

  I've posted my scripts in the past and have gotten useful bits of info, but never a complete solution. Is there a Department within Cisco that I could call so I can explain what I want to do in the room of my client, so I finally buy the right stuff of Cisco and run it the way I'm promising my client it will work?

  Sent by Cisco Support technique iPad App

  Hey Terp, as far as I know, the answer is no. It helps Cisco small business center can provide limited assistance and recommendations, but they are not responsible for your network design and configuration as it is a break fix support.

  Cisco partner you buy carries some of the load to provide information and tips for the proper equipment to buy what you need.

  I know that you posted some scenarios and ideas. It may not be a bad idea to articulate your goals based on what you've learned and try to communicate on the forum and I and probably others can sound to help you to the best of our abilities.

  -Tom
  Please mark replied messages useful

• How is the best way to connect the configuration of my router and switch?

  I have a cable modem. connect to a switch, I have 2 computers connected to the switch. I also just connected my router wireless switch. That's the best configuration or I lose my firewall of the router in passing is not by ports directly above?

  Most of the cable modems will give an IP address, so connect a switch to the modem and then connection of two computers and a router to the switch will usually result in one of these three devices, get an IP address (and internet connection), while the other two will not be.  (Notice that I guess a true "Modem" and not a "Modem/Router" device).  The correct configuration would be to connect your router to the modem (router gets the unique IP address).  The router can then process from the addresses IP what either side LAN of the router, then plug the devices you need (including switch) to the router's LAN ports.  This also ensures that all devices will be on the same subnet that your connection scheme to separate devices on the router wireless from the other two devices on the switch (here, assuming that you have a router/Modem device).

  HTH,

  JW

• Lightroom more slowly than Lr5 cc and struggling for simple cropping and Pan

  I wonder if there is something wrong here. I have a decent machine (2500 k overclocked to almost 5 GHz, GTX570, 8 GB ram, Lr, installed on a SSD).

  LR5 me served well for a long time, and despite its slowness to certain tasks, it is ok. On the other hand, CRD offers very little new features and a decrease in performance.

  I change some 20mp canon raw files and the task simple or cropping/rotation/Pan became a nightmare. It's slow and something seems to be very bad when I try to recrop a virtual copy of an image. At the top very slowly, moving the clipping rectangle sometimes guard reset its position and "refuses" to stay in the place I put it to.

  When I zoom and pan on library mode, everything is going well, he gets only bad on developer mode. If I zoom 1:1 and have some adjustments with the brush of spotting, it feels like I'm panoramic a gigantic file on a 20 year old computer. Even in a clean image with no adjustment, developer mode fight bad pan with zoom.

  
  

  My catalog has around 40 000 files, but it should not matter when a single photo developing. Once again, the same catalog was LR5 and had many questions.

  Checked the use of computing resources, and nothing is really forced to the limit. Total memory usage never exceeds 5 GB (about 8 GB) and the CPU usage does not raise above 40%. If believes that CCRB does not have good use of the computing power available.

  Just replying to me here, I tried to disable this option in preferences > Performance to use my graphics processor and the performance boosted immediately. It is now at the same level as the Lr5.

  I use the version of 350.12 (later like today) of the Nvidia with a GTX570 driver. Apparently, there is a problem on the way that CCRB uses my video card. I hope that this problem is corrected, but at least now my LRcc is usable.

• Router and Switch cannot ping each other

  Hello

  I just build a lab at home.

  In my current lab, I have 2 SW and 3 the router.

  I have a problem, I do not know what Miss me in my config. My router cannot ping my SW.

  and I also want to change my LAN from VLAN 1 interface connection at 30 of VLAN... but when I configure the VLAN 30 he show me line is in PLACE but the Protocol is DOWN.

  Another question, if I want to create a VLAN with a different address, what should I do?

  for example

  VLAN 10 > 10.10.10.1

  VLAN 20 > 20.20.20.1
  etc...

  interface Vlan1 description LAN ip address 10.10.10.1 255.255.255.0 secondary ip address 30.30.30.1 255.255.255.0 secondary ip address 40.40.40.1 255.255.255.0 secondary ip address 20.20.20.1 255.255.255.0 no ip redirects no ip unreachables no ip proxy-arp ip nat inside ip virtual-reassembly dot1q tunneling ethertype 0x9100 hold-queue 100 out!

  Here's the conf for my RT. ROUTER > 877SW > 2950 24 WS

  CISCO_877#sh runBuilding configuration...
  
  Current configuration : 3468 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname CISCO_877!boot-start-markerboot-end-marker!enable secret 5 $1$.ISW$71jzJ0Or0nenXZd/8D8.x/!no aaa new-model!!dot11 syslogip cefno ip dhcp use vrf connectedip dhcp excluded-address 20.20.20.0 20.20.20.30!ip dhcp pool LAN network 20.20.20.0 255.255.255.0 domain-name SYS.local default-router 20.20.20.1  dns-server 202.123.2.6 202.123.2.11  lease 0 4!!!!!username admin privilege 15 secret 5 $1$A1V4$GR9sPtPVXDRoOiDKRtC1M1! ! archive log config hidekeys!!!!!interface ATM0 description (OUTSIDE)ADSL_WAN no ip address no ip redirects no ip unreachables no ip proxy-arp no atm ilmi-keepalive pvc 8/35  encapsulation aal5mux ppp dialer dialer pool-member 1 ! dsl operating-mode auto !interface FastEthernet0!interface FastEthernet1 dot1q tunneling ethertype 0x9100!interface FastEthernet2!interface FastEthernet3!interface Vlan1 description LAN ip address 20.20.20.1 255.255.255.0 no ip redirects no ip unreachables no ip proxy-arp ip nat inside ip virtual-reassembly dot1q tunneling ethertype 0x9100 hold-queue 100 out!interface Vlan30 description LAN no ip address no ip redirects no ip unreachables no ip proxy-arp shutdown hold-queue 100 out!interface Dialer0 description WAN_OUTSIDE ip address negotiated ip mtu 1498 ip nat outside ip virtual-reassembly max-reassemblies 1024 encapsulation ppp ip tcp adjust-mss 1400 dialer pool 1 dialer-group 1 no cdp enable ppp authentication chap callin ppp chap hostname [email protected]/*  */ ppp chap password 7 071C385F5C001D0403 ppp pap sent-username [email protected]/*  */ password 7 120A1C04000208053E ppp ipcp mask request ppp ipcp route default ppp ipcp address accept!ip default-gateway 20.20.20.1ip forward-protocol ndip route 0.0.0.0 0.0.0.0 Dialer0ip route 10.10.10.0 255.255.255.0 Vlan1!no ip http serverno ip http secure-serverip nat inside source list 110 interface Dialer0 overload!access-list 110 permit ip 20.20.20.0 0.0.0.255 anyaccess-list 110 permit ip 10.10.10.0 0.0.0.255 anyaccess-list 110 permit ip 30.30.30.0 0.0.0.255 anyaccess-list 110 permit ip 40.40.40.0 0.0.0.255 anyaccess-list 110 permit ip 50.50.50.0 0.0.0.255 anyaccess-list 110 permit ip 60.60.60.0 0.0.0.255 any!!!control-plane!banner motd ^C
  
  :'######::'##::::'##:'########::'######::'##::::'##:'##... ##: ##:::: ##: ##.....::'##... ##: ##:::: ##: ##:::..:: ##:::: ##: ##::::::: ##:::..:: ##:::: ##:. ######:: #########: ######:::. ######:: #########::..... ##: ##.... ##: ##...:::::..... ##: ##.... ##:'##::: ##: ##:::: ##: ##:::::::'##::: ##: ##:::: ##:. ######:: ##:::: ##: ########:. ######:: ##:::: ##::......:::..:::::..::........:::......:::..:::::..::
  
  ^C!line con 0 no modem enableline aux 0line vty 0 4 password 7 xxxx login!scheduler max-task-time 5000end
  
  CISCO_877#

  And this is for my SW

  CATALYST_2960_01#sh runBuilding configuration...
  
  Current configuration : 5166 bytes!version 12.1no service padservice timestamps debug uptimeservice timestamps log uptimeservice password-encryption!hostname CATALYST_2960_01!enable secret 5 $1$MGrN$PtHgL3KfH0vy7Mr1Fo0hF.!ip subnet-zero!ip ssh time-out 120ip ssh authentication-retries 3vtp mode transparent!!spanning-tree mode rapid-pvstno spanning-tree optimize bpdu transmissionspanning-tree extend system-idspanning-tree vlan 1-4093 priority 16384!!!!vlan 10 name ADSL!vlan 20 name GUEST!vlan 30 name MANAGEMENT!interface Port-channel1 switchport trunk allowed vlan 1,10,20,30 switchport mode trunk switchport nonegotiate spanning-tree cost 1!interface FastEthernet0/1 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/2 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/3 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/4 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/5 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/6 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/7 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/8 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/9 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/10 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/11 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/12 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/13 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/14 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/15 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/16 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/17 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/18 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/19 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/20 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/21 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/22 description SPARE switchport mode access switchport nonegotiate spanning-tree portfast spanning-tree bpduguard enable spanning-tree cost 1000!interface FastEthernet0/23 switchport trunk allowed vlan 1,10,20,30 switchport mode trunk switchport nonegotiate channel-group 1 mode active!interface FastEthernet0/24 switchport trunk allowed vlan 1,10,20,30 switchport mode trunk switchport nonegotiate channel-group 1 mode active!interface Vlan1 ip address 20.20.20.2 255.255.255.0 no ip route-cache!interface Vlan10 no ip address no ip route-cache shutdown!interface Vlan30 no ip address no ip route-cache shutdown!ip default-gateway 20.20.20.1ip http server!line con 0line vty 0 4 password 7 xxxx loginline vty 5 15 login!!end
  
  

  Thanks in advance.

  Eliane,

  Please remove the etherchannel port f0/24 of the switch configuration and store it in the trunk.

  interface FastEthernet0/24 switchport trunk allowed vlan 1,10,20,30 switchport mode trunk switchport nonegotiate channel-group 1 mode active  <<< Remove this 

  Configure f0 on the router as trunk I think has 877, a switchport which fe interfaces are a part of. To display the corresponding Lass on the router, that you need to configure the VLANS corresponding on the router, then only the Lass will be in a State of going / up otherwise it will be in a down state. See if that helps. Thank you, hyacinth

• ACL router and Switch

  Hello.

  I have a small question.

  I implemented a simple extended ACL.

  ip licensing 10.10.10.0 0.0.0.255 192.168.1.0 0.0.0.255

  refuse an entire ip

  It is enabled on the SVI interface IN direction with ip 10.10.10.1/24.

  When I test with the ping from the router to a network blocked from using the interface (SVI) source ACL does not work.

  Example: ping source 172.16.1.5 10.10.10.1 = success.

  This should not be blocked and only allow traffic to 192.168.1.0/24?

  So my questions. The ACL effect on the interface of the router itself and only other hosts on the subnet / vlan? (I think I remember having read about it, but can't find it)

  Thank you.

  Hi traffic there, navigate the interface so that the ACL to be considered. Here is a link to another thread on the forum that explains this very well:

  https://supportforums.Cisco.com/discussion/12043016/pls-explain-SVI-ACL-source-and-destination-direction

  I hope this helps!

  Thank you for evaluating useful messages!

• I have a linksys RV032 router and I want to network traffic using a program

  I work for a customer who has a large mansion. There are about 30 users. Sometimes, the network/internet speed is very high. I want to use a third person monitoring software that will show you the IP whitch makes these high (probably using torrents) traffic rates and how. I have a server there and I woul like to install an ISA Server, but this isn't an option for me.

  You know a software that does this? Thank you.

  Hello

  Please use your favorite search engine to find the software that you will need.

  THIRD WARNING:
  Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

• Need drivers and manual for Satellite Pro 4360

  Hello
  power led flashes after passage and the laptop does not start.
  Who knows where to find manual for Satellite Pro 4360?

  and where you can find drivers for windows 2000?

  TX, michtec

  Hello

  Everything you need you can find on the Toshiba download page, but the important thing is to choose the option ARCHIVE under product type.

• Vista suddenly requires user name and password for peer network XP, WHY?

  Network is a mixture of XP Pro with Vista Home machine. Vista had been particularly transparent connection to a peer network XP, but suddenly invites to indicate the user name and password to login. Only the user for this XP is 'Admin', but login is not necessary. Why is Vista promting to connect? All attempts to answer fast connection with the good username and password fails. Why? How can I make Vista not prompt connection again?

  Try here:

  Vista - XP and Vista Peer to Peer
  http://www.Vistax64.com/Vista-Networking-sharing/126779-XP-Vista-peer-peer.html

• I NEED DRIVERS AND SOFTWARE FOR RUNNING NWIN M8100N 7 ULTIMATE

  I JUST updated MY PAVILION M8100N MEDIA CENTER FROM VISTA to WIN 7 ULTIMATE I DID a CLEAN INSTALL WITH a NEW HARD DRIVE, 4 GB of memory and an ATI RADEON 2600 GRAPHICS CARD WITH 512 MB I WOULD LIKE TO GET THE SOFTWARE AND DRIVERS that is CAME WITH MY SYSTEM AS THE LIGHTSCRIBE, utilities Hauppauge TV tuner & WIN TV THE BEST AUDIO DRIVERS AND THE HP SUPPORT ASSISTANT HP SAY THAT MY COMPUTER IS EXTENSIBLE, BUT WHEN I put WINDOWS 7 in the drop-down list, nothing comes I have improved my DV 9627 cl Notebook that

  HP said was not supported with this forum links to MANY CONGRATULATIONS to ALL OF YOU for THAT. ANYWAY MY M8100N works very well with 5.4 VISTA partition COULD NEVER GET MORE than 3.8.

  MANY CONGRATULATIONS IN ADVANCE YOU PEOPLE REALLY WORK HARD

  Hello

  Don't be fooled by the Windows 7 over VISTA performance index.  Windows 7 uses a scale of differnet.

  Update you the bios and the firmware for the optical drive before the upgrade to Windows 7?  If you need these updates then you will probably need to go back to VISTA to get installed them.  Review available software Vista updates for your PC.

  LightScribe software can be found here.

  Hauppauge can be found here.

  The ATI driver updates can be found here.

  Windows 7 service pack 1 can be found here.

  Realtek audio drivers can be found here.  The features of HP for the m8100n indicate Realtek and not audio Best.

  If you must roll back to VISTA and then run the Microsoft Windows 7 Upgrade Advisor

• Recommendations of the pools and desktop for simple deployment PoC

  So I was the installation and configuration of the Starter View 5 pack (10 connections) for a COP here and went around in a circle a little when it comes to how I should better serve up some of the resources of the office.  Here's the use case.

  Already dedicated VM for remote developers.  Single user for a single virtual machine.

  A couple of computer test virtual than say, a group of 5 people can connect at any given time (for testing)

  A physical computer with a map of PCoIP host that will be negotiated by the view.  One of a handful of people could connect at any time to test.

  All virtual machines are all simple VM with the view agent installed (the composer was not in the mix on any one of them).

  So what I've done, it of just to create a number of manual pools, then give the right to assign users to each, so they can try all of them at once.  Unfortunately, I seem to be consistenly falling on an issue where after a user connects and disconnects, another entitled user tries to open a session and gets the message of: "no source funds assigned to this desktop computer.  Please contact your system administrator. "Newspapers of events indicating: 'machines that responded to the questionnaire are currently in use' I have looked at all the relevant KB, but do not quite get to where I'm running on the problem.

  My approach is wrong?  I'm going to fund these differently to provide more flexible availability during this test?

  Fragmentary salvation,

  Okay, those are the things that come to mind.

  The pool, you have problems, which has dedicated assignment? If so, then when a user connects and gets a desktop computer it becomes assigned to them and no one else can have it even if they disconnect you. Difficulty? Change to floating assignmnet

  Another problem I find is that many users seem to not want to close the session, they simply disconnect the machines. Depending on your settings they porbably is not disconnected until forced. When they are disconnected yet nobody else can connect

  Another thing would be that the machines are turned off/sleep/hibernate after disconnection, but I think the display manager might wake them up, but I'm not sure.

  Basically when you get this error message on what it means that the display manager is looking at unassigned machines and do not get a signal from the agent, which indicates that the machine is, connected to and ready.

  These things sound right?

  See you soon

  Phil

• need username and password for form builder 6i

  I downloaded the zip file of form builder 6i. But what is the name of user name, password, and database? IAM unable to connect to my database. I tried with scott, Tiger and my tns entry in the field of database as well as with the system/admin also... I got this error... "ORA 12154.TNS could not resolve service name". Thanks for giving me the username, password and the name of the database...

  "ORA 12154.TNS could not resolve service name".

  This isn't a matter of user name / it's a configuration problem.

  Do you have what database (and version) installed? Did you run the Net Assistent Configuration to configure your SQLNET. ORA and TNSNAMES. ORA files? Are you able to connect to the database using SQL * more? If so, copy the files sqlnet.ora and tnsnames.ora from your database directory in your repertoire of forms of Oracle (ORACLE of HOME%\Network\Admin %).

  Craig B-)

  If someone useful or appropriate, please mark accordingly.