Similar Questions

• As I installed Sierra, my Trusteer account to my Bank quit and does not work when I reinstall. Neither will Quickbooks!

  As I installed Sierra, my Trusteer account to my Bank quit and does not work when I reinstall. Neither will Quickbooks! Help!

  Trusteer (report) has caused a lot of problems Mac users such noted search Apple Support communities here.

• IPhone 6 IOS 9.3.1 does not ring when a call comes, neither text does not sound a notification.

  IPhone 6 IOS 9.3.1 does not ring when a call comes, neither text does not sound a notification.

  Have you checked the obvious things? E.g.Ring/Silent switch on the left side is not on? Control the volume of ringtone under settings/sounds?

  If they are not serious then have you tried power the phone off and on again? Other sounds work fine, or if all sounds are dumb? for example can play you music through the speaker?

• I just ran the last update for my iPad and now it just continuously reboots to the black screen with the Apple Logo. Hard restarting does not help, neither do not connect the camera to MacBookPro. Any ideas?

  I just ran the last update for my iPad and now it just continuously reboots to the black screen with the Apple Logo. I left plugged in all night and still no change. Hard restarting does not help, neither do not connect the unit to aMacBookPro. When I do this, iTunes complains that it can not connect because the iPad 'expires '. Now it is disconnected, but I can't turn it off. Even close the lid will not extinguish it. Any ideas?

  Try the following. It seems yo may have to let the battery drain is completely:

  - iOS: do not respond or does not light

  -Also try DFU mode recovery mode post-test

  How to put iPod touch / iPhone in DFU "Karthik doodles."

  -If failed and that you cannot completely turn completely the iOS device, leave the battery to drain completely. After loading a hour repeat the foregoing.

  -Try a different cable

  -Try on another computer

  S ' there is still not successful that usually indicates a hardware problem and an appointment at an Apple store Genius Bar is in order.

  Shop Apple Store - Genius Bar

• NEITHER 9871 best way to create the customization to veristand

  I would use a NI 9871 module with NEITHER veristand to connect with over RS-485 devices using the modbus Protocol. I know that this device can be used in mode of scanning and orders VISA, but won't work with the custom device EtherCat Scan Engine.

  I was wondering the best way to change NOR veristand.

  1. Create custom FPGA personality and write the drivers to directly interface with the ports on the device by modifying cRIO Modbus.lvproject http://www.ni.com/example/31166/en/. Expose the commmands as channels passed from the FPGA personality to the workspace and command those from the workspace.Current limitation, I am unsure how to modify this into a custom device or model due to the FPGA IRQ in the RT application used for timing. Can this be included in the custom device?

  2 use the 9871 in scan mode and write a custom device to interact with it using the VISA. Deploy with e/s Modbus device custom servier and send orders to shared variables in the workspace. It would be easier and more robust driver, but I'm not sure how to implement if my other 7 modules use the custom scan engine. I can't apply it in scan mode and the other seven in FPGA because of the DMA only 3.

  3. change the Scan Engine custom device to support 9871? Not sure if this is possible.

  Thank you

  Mike

  4. do not use the NI 9871 and use the serial port on the Crio with a custom modbus device. This leads to a problem of timing, as five devices I want to interact with, I a port. Can reduce functionality.

  An update, since I've found a method that worked well enough and was easier than I expected.

  If you use the cRIO in scan mode with custom device of the scan engine, the ports will appear in MAX for the module 9871. I didn't when I started at the beginning of the post above. From there, you can use all the functions of ports similar to the rs232 port which is included on the NI 9074.

  I wrote a custom device which opened a VISA session at my port and then was able to apply the code I need to communicate with my camera rs485. I worked with modbus Protocol and functions worked within my device custom without modification. I could also adjust VISA settings in MAX and could run a VI of my pc that would send/recieve data ports. This will be useful as an additional way to test or change the settings on my outside NIVS rs485 devices.

  It should be noted in my last post, deploying a Modbus Library did not work. Shared variables of Veristand work incorrectly with the variables that they have been configured in the modbus library that I deployed. I was able to set these manually from the Distributed System Manager. I could also do standard shared variable variables and would update the workspace NIVS in distributed systems manager, they would not change the value in the modbus server. I decided to abandon it and create a custom device that just use VISA vs. shared variables.

• NEITHER Fbus Configurator and Windows 7 compatibility

  Will be that neither FBUS Configurator 3.2.0 works with Windows 7?  If not, is there a way to upgrade? We use an NI FBUS PCI card.

  If an upgrade is required, it is a software or hardware or both that is upgraded?  What is the cost of upgrade?

  Configurator 3.2.x does not support Windows 7. You can upgrade to 4.0.1 Configurator. Only the software requires updating.

  The cost of the upgrade is much lower than the purchase of a new license. For more information, please contact your representative local OR.

• Read and write simultaneously 9375

  Hello

  I have a map of cDAQ DIO 9375 on a slot 4 chassis USB. My question is the card can be configured to perform simultaneous reading and writing? All channel and task VI DAQmx want to read or write. My goal is to be able to use a digital output to trigger a WEAR and use one of the digital inputs to read an output of the object to measure. I know that I can start and stop digital tasks to perform my test, but I was wondering if I am missing the mark in some way.

  See you soon,.

  Emach

  Sorry, I made a mistake in my post original (I blame my lunch to distract me) when I did believe you could do a task timed by the material and a demand.  You can either make on request of materially call GOLD a tasks tasks in one sense.  This means that if you want to DI and DO, you need to use two modules or on demand.

• NEITHER USB-6501

  Hello

  Could someone give me some information about whether it is possible to use the

  NEITHER USB-6501

  As a generator PWM to control the dimming of 18 power LED function?

  calendar is not so relevant and if the pulse width can be controlled in the PC itself application the purpose would be financed

  Hello ONavarro,

  It is technically possible, but please note that USB-6501 as only software clocked e/s digital (e/s static). In other words the duty cycle of the PWM periodocity Ant you want to generate will be determined by a loop software, so depending on your system and the USB bus. I think that you will not be able to get a better rate of loop (ability to change the State of a digital line) less than some milliseconds (depending on the system).

  By example, if the loop runs at 5ms, and I want 10 steps in my PWM, this means the period will be 50ms, therefore a 20 Hz base frequency. If you can't reach 1ms, you will get 100 Hz. If you want more than 10 duty cycle value, you reduce the frequency.

  And it is NOT stable (loop software 5ms, first delta 5.8ms, then 4.9ms, 5.1ms, 6.7ms, and so on), because it is based on the software. If you need something stable and faster, choose a device with hardware synchronizing.

  Best regards

• Model VeriStand compilation error: NEITHER VeriStand 2010 cannot find the struct parameter in CGTypes

  Hello

  I get this sequence of messages when I try to compile a model.

  ...

  # Generating API interface TLC.
  ...........................................................
  # NEITHER VeriStand 2010 modifying Pack_L500_IB_plant_fstep_io.c file
  ...................................
   
  # NEITHER VeriStand 2010 modifying Pack_L500_IB_plant_fstep_io_data.c file
  Error: # NOR VeriStand 2010 cannot find the struct parameter in CGTypes
   
   
  # NEITHER VeriStand 2010 modifying Pack_L500_IB_plant_fstep_io.h file

  # File Readme of Ports generating NI VeriStand 2010
  Could not find c:\WorkDir\Models\Pack\pack_l500_ib_plant_fstep_io_niVeriStand_rtw\*.obj
  # Time real workshop build procedure for model: 'Pack_L500_IB_plant_fstep_io' aborted due to an error.

  I tried to repair my VeriStand 2010 installation and always errors.

  I created a VM, installed Simulink and Veristand and tried to recompile the template. Error appers again.

  I changed the "target system" (tlc file) in general relativity, and the model has been compiled without errors. Same VxWorks Veristand target fails.

  If I copy the other target to target VS the second error le.obj goes but I always "error: # NI VeriStand 2010 unable to find parameter struct in CGTypes.

  How can I solve this problem?

  See you soon,.

  Claudio H.

  Hello

  I found the problem but not the reason.

  If I change the Settings of Configuration > Optimization > Parameters Inline unchecked = the template compiles without problems.

  See you soon,.

  Claudio H.

• How can I know if NEITHER-DAQmx is installed on my pc?

  Stupid question, but I need to know:

  How can I know if NEITHER-DAQmx is installed on my pc?

  Thank you.

  It will appear to the MAX (Measurement and Automation Explorer).

• NEITHER 9485 Circuit question

  I have a problem with a NEITHER-9485.  I'm telling us to turn on a relay high voltage AC.  I have the + 24V need to run the HV to CH0a relay.  CH0b is connected to the positive of the HV relay coil.  The negative of the HV relay's coil is connected to the Earth.  When I turn on + 24 volt, no matter the State OR-9485 I get 10 my of current that turns on the relay HV.

  If I remove the connection with the NI 9485 module and hook upwards on the ohmmeter to him, the relay works very well.  If I can replace the NOR-9485 a NOR-9481 has closed the only current when the NOR-9481 is ordered.  NOR-9485 was chosen because of the number of channels.

  Does anyone know why the NOR-9485 like no switch + 24V?

  Glad it worked!

  Have a nice afternoon.

• How to continually take and record waveforms with neither 5102

  a machine generates waves sinusoidal time randomly. I want to permanently take and record waveforms in 10s by NI 5102.

  How to do?

  Thank you very much!!

  Thanks for the review! but this isn't a supported NEITHER.

  I record signals by this method.

  and the promble news is that different sampling frequency, the different wavelength. for example, when I put the sampling frequency is 4 k, the wavelength is 12 seconds if the sampling frequency is 10 k, the wavelength is 8 seconds the signal under test 1 k, the time constant is 10000.

  now, I save waveform to 10 sec. What is the best relationship between sampling frequency and the time constant?

• NEITHER Starter Robotics it

  Hello

  I am interested in this kit 'DANI'... really I intend to buy it to have on the sbRIO-9632 trained in real-time applications.

  My question is after having used this kit in with examples of labview training... I'll be able to use the sbRIO 9632 in another application also for motors continuous command.

  I would like to build a project of DC motor Position control

  using a mould to tilt mechanism and I think to get use of the sbRIO 9632 and the circuit of engine on this kit and use it to Pan tilt mechanism

  I have waiting for a tilting mechanism pan with two engines 12DC, this mechanism also has a pot. for your comments.

  I'll go and buy this robot kit and you train?

  Am I able to disammble (without losing its function as a robot when gathered) and use the tips (driver sbRIO9632 and motor circuits) need in my project of pan/tilt?

  Thanks in advance

  The sbRIO on the robot Starter Kit still usable by itself, even if it is removed from the robot.  You can use it as any other sbRIO-9632.  One thing to keep in mind is that you will need to provide a power supply for the Board once it is removed from the robot.  It requres a 19 to 30 VDC power supply.

  Regarding your question about to dismantle the robot, there is no reason that this will not work if if it is installed correctly.  Do not forget that you would be responsible if yes or no it works once reassembled, because NEITHER does not officially support dismantling the robot.  There is no diagrams or instructions (that I know of) to do this.

  Chris M

• Why only part of the "basler GIGe scout" cameras are NEITHER taken care of?

  Is the pag web cameras OR update support?

  I do not think that NEITHER can list every single device that is compatible with GigE interface.  It may just be a list of cameras, they have actually tested and checked.  If some of the Basler Scout cameras are listed, I guess all they would work.  I don't know that they all have the same hardware to interface.

  Bruce

• NEITHER 9233 Microphone conditioning of signals

  Following an update of LabVIEW 2009 Pre - polarised FAT microphones work correctly with 9233 modules OR multifunction data acquisition. (They have been used regularly since 2007).

  There is an important distortion of the signal calibrated showing the cutout of the positive part of the trace to higher levels of entry.

  Connection from one system to the external packaging of signals MIC shows perfect sinusoid using the same (FAT 40AE) microphone capsule, (BOLD 26CF) amplifier, cable and NI 9233 - we have 2 examples of each element.

  The only element that seems common to the fault is the conditioned signal of the NI 9233 following the update of LabVIEW 8.6 in 2009. I tried to change the level of excitement from 2mA to 4 and 8 with no benefit (specification of FAT said 4mA nominal 2-20 MA). I noticed that there are a few changes in the terminal configuration option dialog, but after trying to change this, it is the only viable option "nickname".

  The determination of sources of external power and excitement for the microphone is not an option for practical reasons, but it does not restore the original function.

  Is there a change documented 9233 with LabVIEW 2009 service or is there a simple solution to this change in behavior?

  Thank you.

  The interests of other users, it seems that the microphone needs a little more excitement to 114dB, where cut when it is used with the 9233 which can only provide 2mA. The installer works fine at 94dB, where 2mA is enough excitement. There are no errors appearing in the software, since it is a hardware limitation.

  Kind regards

  Michael S.
  Technical sales engineer
  NEITHER UK & Ireland