Similar Questions

• PIX of VPN in several subnets

  We have two remote sites and a framework to our parent company

  the tunnel works very well between us and our remote offices, but they cannot connect to the internet application server and oracle on the parent through site framework

  I have roads on our internal to the remote site router and our 520 pix for the address of the frame. How configure you routing for frame internal? 520 PIX can ping servers and network frame

  set up 6.3 (3) version PIX

  | Oracle application server and Intranet 173.1.2.X |

  |

  | Parent | net 173.1.2.0

  |

  |

  | framework

  |

  | Internal router | 192.170.1.x

  |

  | PIX 520 our company | net 192.170.1.0

  |

  | External router: x.x.x.x

  | |

  | VPN |

  | |

  | PIX 501 remote sites. 192.170.2.0 and 192.170.3.0

  501 sh IPSEC Security Association shows 0 for all counters

  520 HS IPSEC security association

  local ident (addr, mask, prot, port): DI (DI/255.255.255.0/0/0) = FRAME

  Remote ident (addr, mask, prot, port): (192.170.2.0/255.255.255.0/0/0)

  current_peer: X.X.X.X:0

  LICENCE, flags is {origin_is_acl},

  #pkts program: encrypt 0, #pkts: 0, #pkts 0 digest

  #pkts decaps: 0, #pkts decrypt: 0, #pkts check 0

  compressed #pkts: 0, unzipped #pkts: 0

  #pkts uncompressed: 0, #pkts compr. has failed: 0, #pkts decompress failed: 0

  #send 101, #recv errors 0

  endpt local crypto. : X.X.X.X, remote Start crypto. : X.X.X.X

  Path mtu 1500, fresh ipsec generals 0, media, mtu 1500

  current outbound SPI: 0

  SAS of the esp on arrival:

  the arrival ah sas:

  SAS of the CFP on arrival:

  outgoing esp sas:

  outgoing ah sas:

  outgoing CFP sas:

  520 logs shows the key request his

  702303: sa_request, (ING. MSG key) src = X.X.X.X, dest = X.X.X.X, sr

  DI/255.255.255.0/0/0 (type = 4) = c_proxy, dest_proxy = 192.170.2.0/255.255.255.0/0

  / 0 (type = 4), Protocol = ESP, transform = esp - esp-md5-hmac, lifedur = 28800 s a

  4608000 Ko d, spi = 0x0 (0), id_conn = 0, keysize = 0, flags = 0 x 4004

  It's certainly an issue access list, I'll watch this Monday. Could you please give me a printout of the

  NAT (inside) 0 access - your name-list ACL.

  access - your name-list ACL...

  sincerely

  Patrick

• VLAN: ESXi <>- Cisco SG300

  Hey everybody,

  I always try to get the hang of networking with ESXi/vSphere...and I was little confused as I had a configuration problem.

  I have an Intel NUC5i5MYHE with 5.5 ESXi. As he has that one NETWORK card I am configuring a trunk so I can separate groups of ports within the host with the VLAN.

  Cisco SG300 has several VLANs (including: HAND = 10, LAB1 = 20, LAB2 = 30). * 1 is still active but VLAN native = 999 *.

  MAIN are all fair access Ports on VLAN10 (10UP).

  GE22 is a trunk with VLAN 10, 20 and 30 with label (10T, 20T, 30t, 999UP).

  A few groups of host ports ESXi has currently (simply called the VLAN I want installation and set on the VLANs)

  Also, I created the extra VMkernel port with VLAN10 just for wasting his time with (I can't access to this IP address, but after looking at VMK0, I think that I need to add static routes to the bridge?)

  V0 & VMkernel 0 = VLAN 0 (none)

  V10 & VMkernel 1 = VLAN 10

  V20 = VLAN 20

  So, with this configuration, I am unable to access the host via vSphere Client. However, if I put GE22 on SG300 to 10UP (10UP, 20T, 30t) I AM able to access... but is not what I want, right?

  To my knowledge... 0 (none) passes a VLAN while 4095 (all) does not take into account any VLAN tags completely, sending the frame as-is to the customers. (While I would let VMK0 0 (zero) as the correlates directly to my unique NIC physical, right?)

  So... my computer that connects with the vSphere Client Gets VLAN10 penetration tag (access). Switch then forwards Egress GE22 through the trunk to the ESXi host with a labeled VLAN10 framework.

  The framework should be accepted at the VMK0 whatever the tag VLAN and connect or if the frame belonged to another customer sent on the vSwitch... unless I'm confused here somewhere.

  Can someone enlighten me please?

  Thank you

  Basically, you have two options. If native/default of the physical switch port VLAN is set on the Management VLAN, then do not set a VLAN ID on the management VMkernel port group, otherwise the value the VLAN ID on the virtual side. Ultimately that a single point (the physical switch port, or the virtual port group) is responsible for the labelling/close the network frames.

  André

• How to distinguish between couples that comes from my TX CAN oppose and frames which comes from the network?

  HY,

  I have an object can pass data to the specific id.

  I expect to get frame from the network with IDs and similar data.

  How will I know that the data came from the network?

  (If I listen to the data of the CAN Interface, I can't distinguish the data that I convey and between data from the Internet)

  Thanks in advance,

  Aviad

  Since you are using NI-CAN, series 1, which does not support no matter what Self-reception, I assume you are using two ports CAN... make your normal transmission and the other to listen to the frames of the CAN bus?

  If this is the case, the only option I see for you would be to compare the charge received with the load transmitted to detect the images you send. This will only work if you send and receive different payloads, but it's probably something that's generally true. If it is false, then you really have no good option with the 1 series (or even series 2) and NI-CAN.

  We have a different product, OR-XNET, which provides a forum for independent reception (such as series 2 NI-CAN), but when you receive the framework that it contains a flag that indicates if it was received from the network or received through self-reception. It's of course far easier (and probably only guaranteed) way to achieve your goal.

• I have a PC and disconnecting network connections, can I remove Net frame and Nvidia Force

  I use Windows XP and Explorer 8 and not have that a PC Networking connections have been disconnected. Question: work Net Frame, Nvidia Force or any removable elements without any complications? Thank you for your kind attention Herbert

  # Need to post at least 6 characters, so this sentence is filling.

• Grouping of NETWORK cards causing the ESXi to retransmit ethernet frames received.

  I had an HP Proliant DL380 G5 ESXi 5.1.0 connected to a Cisco 3750 Switch stack.

  All by performing a tcpdump on a host without a report, I discovered that he was under the bombardment with ethernet frames for the MAC address of a computer virtual located on a host across the data center. After a few brief troubleshooting, I discovered that I was able to stop those erroneous frames by disabling NETWORK adapters on my VMWare host group.
  
  I believe that in my situation when ESXi is configured to use two network cards to all frames received on vmnic0 and retransmits them on vmnic1 and vice-vesa. I experienced these symptoms when ESXi is configured for failover with an active adapter and adapter mode standby and I also experienced the same symptoms in the following load balancing configuration.
  

  
  

  Symptoms: some time after activating the load balancing, all frames Ethernet for the MAC address of a virtual computer on the affected host are broadcast on each switch port in the entire data center.
  
  Steps to reproduce:
  (1) implementation below configuration.
  (2) unplug the ethernet cable connecting vmnic1 and switch1 port gi2/0/4
  (3) run the host 1.1.1.1 EI - n - q tcpdump on any machine physics linux in the data center (don't even have to be connected directly to 1).
  Confirm there is no packet seen with the IP address of 1.1.1.1 destination
  (4) plug the cable between vmnic1 and switch1 gi2/0/4 port ethernet
  (5) wait 60 to 120 seconds
  (6) watch a burst of frames ethernet with the destination MAC address of the VM (which owns 1.1.1.1) in the output of tcpdump

  Cisco Configuration:

  hostname switch1
  !
  src-dst-ip port-channel load-balance

  !

  interface GigabitEthernet1/0/4

  Description vmnic0.host0 (NIC 1)

  switchport trunk encapsulation dot1q

  switchport mode trunk

  channel-group mode 4 on

  spanning tree portfast trunk

  end

  !

  interface GigabitEthernet2/0/4

  Description vmnic1.host0 (NIC 2)

  switchport trunk encapsulation dot1q

  switchport mode trunk

  channel-group mode 4 on

  spanning tree portfast trunk

  end

  !

  Interface Port-Channel 4

  Host0 description

  switchport trunk encapsulation dot1q

  switchport mode trunk

  spanning tree portfast trunk

  end

  
  Configuration of ESXi
  vSwitch0

  Grouping of NETWORK cards / Load Balancing: route based on IP Hash
  Grouping of NETWORK cards / failover detection network: link status only
  Grouping of NETWORK cards / notify switches: Yes
  NIC Teaming / relief: Yes
  Grouping of NETWORK cards / adapters active: vmnic0, vmnic1
  NIC Teaming / standby adapters: nothingness
  NIC adapters grouping / unused: nothingness
  Security / Promiscious Mode: reject

  Security / MAC address changes: accept
  Security / forged passes: accept

  
  #1 Virtual Machine port group
  Network label: 'Public '.

  VLAN: 27
  Grouping of NETWORK cards: all unchecked (inherited)

  #2 Virtual Machine port group
  Network label: "trunk".
  VLAN: 4095
  Grouping of NETWORK cards: all unchecked (inherited)

  VM kernel Port #1
  Network label: 'management '.
  VLAN: 2

  Grouping of NETWORK cards: all unchecked (inherited)

  VM #1
  

  OS: Windows Server 2003
  NIC 1 / adapter: Flexible
  NIC 1 / network Label: 'Public '.

  IP address: 1.1.1.1/24

  I apologize for the delay in my response.

  Unplug physically 2 cable NETWORK card on the host and configuration mirrored port on the switchport to 1 NETWORK adapter of the host, I have been able to confirm that the host VMWare issues guides on NIC1 with a destination MAC address of one of its own VM.

  After carefully reviewing the captured data, I noticed that the destination frames wrong "02:bf:cb:50:a2:76" MAC address actually belonged to "Local Area Connection 1' one of my Windows 2003 Server WHAT VM installed on the suspected host.

  Dig a little deeper, I discovered that this virtual NETWORK card is presented to the operating system as
  Name: Local 1 network connection
  "Type: VMware Accelerated AMD PCNet adapt."
  MAC: 02-BF-CB-50-A2-76

  But the configuration of the virtual machine in vCentre is
  Name: Network adapter 1
  Type: Flexible
  MAC: 00: 0C: 29:fa:e8:83

  Note the different MAC addresses.

  Digging a little further I discovered that Windows 2003 server has configured on "Local 1 network connection" network load balancing and NLB is the cause of the altered MAC address.

  Rather than to investigate further I have just placed a load balancer linux before the server windows 2003 cluster and that you turn off NLB.

  But I suspect that there is still a fundamental problem in the Virtual Switch VMware with how he learns the MAC addresses of the virtual machine is using flexible vNIC. In particular, with a virtual machine that uses a form to override the MAC address such as that used by NLB.

• Validate the design of the network 2 x 10 GbE - NAS only 4 x 1 GB (jumbo frame)

  Dear Sir

  I have a few questions about the design of our new vSphere environment network.

  Detail:

  -Enterprise license

  -vSphere 5 servers (HP DL360p) with each:

  128 GB memory

  2 x Intel E5-2665 (8 cores)

  2 x 10 GbE (HP FlexFabric 554FLR-SFP +)

  -Environment NAS is connected via a LACP of 4 x 1 GB (no dedicated storage network)

  -Network environment is built on Juniper EX4200 is (virtual stack)

  Should / can use frames? :-)

  (a) servers, VMware will have 10 GbE and the storage network is only 4 x 1 GB?

  (b) this will give no problem for end-user connections that connect to the server VM

  running on the infrastructure as the file servers...

  Everything will not use frames but the will of the end user of PC, or is this not a problem?

  Is the picture below to go to the best?

  GRZ,

  Geert

  Honestly, there are a lot of discussions on when to activate the frames.  In my opinion I do not activate initially jumbo frames and watch the traffic.  If the backen was totally 10 GbE or FC, I would definietly enable Jumbo.  If necessary, then I would allow him.  Frames Jumbo will not affect the user who connects to the virtual computer, remember that they need to connect to the ESXi and not the current storage unit.

• Frames extended network of workstation support?

  Another question about the features of Vmware Workstation 7.1 networking. At switches virtual support for jumboframes? I did not take anything in the manual which says that it is or is not.

  It should be interesting to test setup in different operating systems, but also perhaps to lower if possible host CPU utilization.

  According to the information on page 32 of Performance Best Practices for VMware Workstation frames are not supported in VMware Workstation.

• How to send frames to header + 1 byte of data in network LIN?

  Hello

  I use USB-8476 to communicate to a slave in a LIN network. Can someone tell me how I can send a header file more 1 byte of data to the slave in a LIN network.

  I need to send a sync + id 00 X 34 break, followed by a byte of data. I don't know how a master can send this extra 1 byte of data. I need to send this command to the LED and byte 1 to control the level of illumination of the LED lights.

  If anyone has examples for this, can share you here?

  Thank you

  Hi Andreas,

  This error has not yet been documented, but I got the information on the other forums.

  Error name error Code (hex) description

  Task-master of 1040 LinBusErrorTxSyncTimeout LIN interface is trying to send a

  synchronize the bytes and not not not receive the sync byte

  during the period.

  This is the description. The problem is solved, the baud rate I gave was higher than the speed of the slave units. Now, it seems to work correctly.

  Thank you.

• Jumbo Frame on 1 Gig network

  Hello

  I'm using iSCSI based shared the storage configuration on the 1 Gig host connectivity, iSCSI, physical switch software and storage.

  Should I enable the jumbo frame on all devices of connection in order to have a higher flow rate?

  It will cause no problem as the connection to the store of data or something like that?

  Kind regards

  Sushil

  Allow executives to Jumbro for the IP storage is recommended, in any case may be a glance on the following link to see a few considerations and test results on the Jumbo Frames: Jumbo Frames comparison test with storage over IP and vMotion & raquo; boche.net & #8211; VMware vEvangelist

• Using too much CPU only when loading the network

  When FF works closely with the network (wired or wireless) card for access to the network, CPU utilization spikes in way more than 70% and he stayed there until the page loading process finishes web.
  After the upload is complete, the CPU usage remains somewhere between 5-10%.

  When I look at clips youtube 1080 p, where FF is duty next buffer part of this clip I watch, new CPU use peaks above 70% with the flash plugin and gives a total of a 100% of cpu for a few moments and use which make this clip to stop playing or to frame bad times, and ties.

  I have been activated in about: config webgl acceleration to activate the force and that much improve the initial problem, then I activated gfx.direct2D - activated force and also to improve the problem remaining.
  I also disable the safe_mode parameter file adobe flash config protectedmode = 0.

  I have to mention that the initial problem was way to bad ... 
  

  Now I get to point when I don't know what to do so that FF does not use much CPU loading pages.
  As you can see I use to publish this version of Nightly 64 bit (I think it's the 64-bit version...) which is much more better and I would like to read youtube 1080 p clip normally, after that I have wait a few moments to buffer, before starting to play.
  Version 32 bit FF won't let me watch YouTube without framing hurt when the clip is buffered.

  I was monitoring the Task Manager and all the processes listed... and there, I can't blame antivirus or firewall to the peaks of the processor. Also if I do the rest of the network traffic, as well as inside the network custom CPU even file copy flinch.

  Can someone help or give an opinion on what setting to do, so I can eliminate these spikes?

  Thanks in advance!

  Problem solved partially:

  I have observed that the CPU spikes occur not only while I use FF or mozilla nightly, but on all web browsers (Chrome, IE, Opera, etc) that I have used, while these browsers accessing the network.

  Uninstalling the firewall of the solution of the AV portion has helped a lot and by also disabling the bed in the firewall solution of W7, but for long term use, this isn't the right answer (for my at least). Without any firewall FF work or installed works like a charm, while the CPU usage is increased at a decent level of 50% max (total tasks and running services)!

  Anyway, as I said earlier, my pc without any firewall operation is not a good think to do, so I'll replace my computer with a faster, or I'm going to overclock it at a level that zapping INTERNET and navigation will not infringe too much on the performance of the system, or... I live whit it and I accept the limitations...

  Perhaps, in the development of the FF, programmers will keep in mind that not everyone on this planet has powerful processors - and... give a few options... to decrease the CPU at acceptable levels, event, even if they use the firewall solutions that violate on the CPU while FF is buffering of data across the network.

  I should also mention that Mozilla nightly (64-bit) and FF, are always better then IE - in my opinion - which is.

• HP Omen 15 5012tx: impossible to uninstall network solutions HP (HP Omen 15 5012tx)

  I'm trying to re install HP solutions network framwork and it tells me I need to find a specific .msi file but I don't have it.

  

  Then I get this message...

  

  Is the .msi file above available for me to download on the official site of HP?

  I also have a problem opening HP support Assistant program because it seems not at all to open whenever I double click on it. I thought it had to do something with support hp solutions framework and I can't update the program because I get the same message that I need a .msi file.

  Everything worked fine before...

  batruto

  install frames

  Control Panel > turn Windows feature on net. 3.5 a 4.6

  reset

  Run Windows update

• Major Frame Drops after 5-10 minutes

  Hello world

  I'm really frustrated here, I'm a game developer, and I use the GPU in almost all cases, from Photoshop to unity still play games myself. Since the last update 10.11.4 I have this huge problem , and everything I do will not disappear.

  Whenever I run an application / game that rotates with GPU I get spikes massive lag and thus Frame Drops, they last about 1 seconds but they occur every 30 seconds - 1 minute, this is a huge deal for me and I can't really work like that. Of course, I put photoshop to the CPU usage for now and no problems. But I really need to work efficiently and without Frame Drops.

  I run at El Capitan with a Macbook Pro LATE 2013 10.11.4 @.

  2 GHz Intel Core i7 (CPU)

  8 GB 1600 MHz DDR3 (RAM)

  Intel Pro Iris 1536 MB (GPU)

  Before someone says I should have got the Nvidia gpu, I should mention that I tried on 2 games to 1 which I played with ease previously:

  Hand of fate

  The Witcher: Enhanced Edition

  Please if someone else has the same problem, make sure that post you here. It bothers me that I have not found anything about the case.

  I also ran an EtreCheck if anyone is interested:

  EtreCheck version: 2.9.11 (264)
  Report generated 2016-04-16 15:29:41
  Download EtreCheck https://etrecheck.com TIME 01:31
  Performance: Excellent

  Click the [Support] links to help with non-Apple products. Click the [details] links for more information on this line.

  : Another problem
  Description:
  Whenever I use an application that uses GPU or if I play a game, I get large Frame drops after 5-10 minutes in application t.

  Hardware information:
  MacBook Pro (retina, 15 inches, end of 2013)
  [Technical details] - [User Guide] - [warranty & Service] MacBook Pro - model: MacBookPro11, 2
  1 2 GHz Intel Core i7 CPU: 4 strands
  8 GB RAM not extensible

  BANK 0/DIMM0
  OK 4 GB DDR3 1600 MHz

  BANK 1/DIMM0
  OK 4 GB DDR3 1600 MHz

  Bluetooth: Good - transfer/Airdrop2 taken in charge Wireless: en0: 802.11 a/b/g/n/ac
  Battery: Health = battery check - Cycle count = 460

  Information about this video: Intel Iris Pro

  Color LCD 2880 x 1800

  System software:
  OS X El Capitan 10.11.4 (15E65) - since the starting time: 4 hours

  Disc information:
  SM0256F SSD APPLE disk0: (251 GB) (Solid State - TRIM: Yes)

  EFI (disk0s1) < not mounted >: 210 MB

  Recovery HD (disk0s3) < not mounted > [recovery]: 650 MB

  Macintosh HD (disk 1) /: 249.79 (GB free 65.99) encrypted AES XTS unlocked
  Storage of carrots: disk0s2 250.14 GB Online

  USB information:
  Apple Inc. Apple keyboard / Trackpad

  1. the present proceedings is a diagnostic test. It doesn't change anything for the better or worse and therefore, by itself, will not solve the problem. But with the help of the results of the tests, the solution may take a few minutes, instead of hours or days.

  The test works on OS X 10.8 ("Mountain Lion") and later versions. I do not recommend running it on older versions of Mac OS X. It will do no harm, but it will not do not much good.

  Do not be put off by the complexity of these instructions. The process is much less complicated than the description. You make the tasks more complicated with the computer all the time.

  2. If you do not already have a current backup, please back up all the data before doing anything else. The backup is needed on the general principle, not because of what anyone in the test procedure. Backup is always a must, and when you encounter any kind of problems with the computer, you can be more than the usual loss of data, if you follow these instructions or risk not.

  There are ways to back up a computer that is not fully functional. Ask if you need advice.

  3 here is instructions to run a UNIX shell script, a type of program. As I wrote above, it doesn't change anything. It does not send or receive data over the network. There is no to generate a report on the State of the computer human readable. This report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents for me or someone else.

  You should ask yourself if you can believe me, and if it is safe to run a program at the request of a foreign national. In general, no, he's not sure, and I encourage it.

  In this case, however, there are ways for you to decide if the program is safe without having to trust me. First of all, you can read it. Unlike an application that download you and click to start, it is transparent, anyone familiar with the code can check what it does.

  You may not be able to understand the script yourself. But variations of it have been posted on this site several times over a period of years. One of the million registered users to have read the script and set off the alarm if it was dangerous. Then I wouldn't be here now, and you would not be reading this message. See, e.g., this discussion.

  However, if you cannot satisfy yourself that these instructions are safe, do not follow them. Ask other solutions.

  4. here is a general summary of what you need to do, if you decide to go forward:

  ☞ Copy text from a particular web page (not this one) to the Clipboard.

  ☞ Paste into the window to another application.

  ☞ Wait for the test to run. It usually takes a few minutes.

  ☞ Stick the results, which will be copied automatically, in a response on this page.

  These are not specific instructions; just a glimpse. The details are in parts 7 and 8 of this comment. The sequence is: copy, paste, wait and paste it again. You don't need to copy a second time.

  5. try to test in conditions that replicate the problem, to the extent possible. For example, if the computer is slow intermittently, run the test during a downturn.

  You may have started up in safe mode. If the system is now in safe mode and works pretty well in normal mode to test run, restart as usual before running it. If you can test only in safe mode, this.

  6. If you have more than one user and a user is affected by the problem, and the user is not an administrator, and then run the test twice: once under the affected user and one administrator. The results can be different. The user that is created automatically on a new computer, when you start it for the first time is an administrator. If you are unable to log in as an administrator, verify that the user concerned. More personal Mac have only one user, and in this case this section does not apply. Don't log in as root.

  7 load the linked web page (the site "Pastebin.") Press the combination of keys command + A to select all the text, then copy it to the Clipboard by pressing command-C.

  8. start the Terminal application integrated in one of the following ways:

  ☞ Enter the first letters of his name ("Terminal") in a Spotlight search. Select from the results (it should be at the top).

  ☞ In the Finder, select go utilities ▹ of menu bar or press the combination of keys shift-command-U. The application is in the folder that opens.

  ☞ Open LaunchPad and start typing the name.

  Click anywhere in the Terminal window to activate it. Paste from the Clipboard into the window by pressing Command + V, then press return. The text that you pasted should disappear immediately.

  9. If you logged in as an administrator, you will be prompted for your login password. Nothing displayed when you type. You won't see the usual points instead of the characters typed. Make sure that caps lock is turned off. Type carefully, and then press return. You can get a warning to be careful. If you make three unsuccessful attempts to enter the password, the test is still running, but it will produce less information. If you do not know the password, or if you prefer not to enter, just press back three times at the password prompt. Yet once again, the script will run.

  If the test takes much longer that usual to run because the computer is very slow, you can be prompted for your password a second time. The permission you grant by entering it will expire automatically after five minutes.

  If you are not logged as an administrator, you will be prompted for a password. The test will run. It just will not do anything that requires administrator privileges.

  10. the test may take a few minutes to run, depending on the number of files you have and the speed of the computer. A computer that is abnormally slow may take more time to run the test. During execution, a series of lines is displayed in the Terminal window like this:

      Test started

          Part 1 of 4 done at: … sec        …        Part 4 of 4 done at: … sec

      The test results are on the Clipboard.

      Please close this window.

  The intervals between the parties will not be exactly the same, but they give an approximate indication of progress.

  Wait for the final message "Please close this window" appear - again, usually within a few minutes. If you don't see this message in about 30 minutes, the test probably won't be completed within a reasonable time. In this case, press the Ctrl + C key combination or the point command to stop it. Then go to the next step. You will have incomplete results, but still something.

  In order to get results, the test should be allowed to perform or be stopped manually as shown above. If you close the window of the Terminal, while the test is still running, the partial results will not be saved.

  11. when the test is completed, or if you manually stopped, leaving the Terminal. The results have been saved to the Clipboard automatically. They do not appear in the Terminal window. Please do not copy from there. All you have to do is start a response to this comment and then paste it again by pressing Command-V.

  At the top of the results, there will be a line that begins with the words «Start time.» If you do not see that, but rather to see a mass of gibberish, you wait for the message "close this window". Please wait and try again.

  If personal information, such as your name or e-mail address, appear in the results, make anonymous before posting. Usually it will be not necessary.

  12. in the validation of the results, you see an error message on the web page: "you have included content in your post that is not allowed", or "the message contains invalid characters." It's a bug in the software which manages this website. Thanks for posting the results of the tests on Pastebin, then post here a link to the page you created.

  If you have an account on Pastebin, please do not select private in exposure menu to paste on the page, because no one else that you will be able to see it.

  13. When you are finished with the test, it is gone. There is nothing to uninstall or clean.

  14. This is a public forum and others can give you advice based on the results of the test. They speak for themselves, not for me. The test itself is harmless, but all that you can not be. For others who choose to run it, I do not recommend that you view the results of test on this Web site unless I ask.

  15. the related UNIX shell script is a notice of copyright. ASC readers can copy for their personal use. The whole nor any part can be redistributed.

• Can I check my speed of network (not the internet) on tv4 from apple?

  Hello

  I have problems streaming an HD movie to my pc windows to apple tv4, I use the plex app server and media. that works very well on all SD movies, but I get a lot of buffering on HD (10.9 Gig) movies, I tried wireless and ethernet, but both have buffering of questions then I would only test network speed I'm getting with wifi, ethernet via Powerline or direct ethernet so I know not to invest in a better wireless modem or if it's the software or other problems.

  Thnaks in advance

  Chris

  think I saw and app for him but he could have been another internet speed measured only application

  But if you have tried ethernet then unless your router is older then the wheel, then it would execute is 100Mbit which should be more then enough to stream hd you tried with hd movies less 10.9 GB seems a little heavy

  Another thing you should consider is what format

  Video formats

  Video H.264 up to 1080 p, 60 fps, high level or hand Profile 4.2 or lower

  Formats H.264 Baseline profile level 3.0 or lower with AAC - LC audio up to 160 Kbps per channel, 48 kHz, stereo audio in .m4v, .mp4, and .mov file

  MPEG-4 video up to 2.5 Mbps, 640 x 480 pixels, 30 frames per second, basic profile with AAC - LC audio up to 160 Kbps, 48 kHz, audio stereo in .m4v, .mp4, and .mov file formats

  of https://www.apple.com/tv/specs/

  If your movies are in no! Another plex format could be all software decoding instead of leaving the appletv chip do material which means a better performance of the 1000 mkv or tastes would be in this category

  You can try to convert them using the free converter called Handbrake program and see if you get better performance with h.264 codec

  and your network could be innocent to 100% if the problems you are having

• Dropped frames and jerky video ATV4 TVOS 9.2

  I'm having a problem with my Apple TV after upgrade to TVOS 9.2. Whenever I play video (especially videos YouTube, but this also happens with other applications such as WatchESPN), after a while, the video begins a fall frames and the sound is not synchronized with the video. I can remedy temporarily by force, killing the app or by restarting the Apple TV, but it comes back later and video will get out of sync and drop frames. How to solve this? This came after my update for TV OS 9.2.

  Sounds like a network problem.  Check that you are connected to the correct wireless.  Some routers are dual band, so make sure you're on the 5 GHz band.  If this does not work, I do a full restore back to factory settings and re-setup.  I know it's a giant pain, but if this isn't a connectivity problem, this is a question of OS.