Network traffic software?

Similar Questions

• Wireless - C6180 network traffic

  Product: Photosmart C6180 all-in-one

  The printer has been set up wireless to share among 5 computers and works very well.  My concern is that the amount of traffic network the printer generates.

  I analyzed the network traffic generated by my computer using Wireshark Analyzer (packet sniffer) network protocol.  Traffic is presented as a series of SNMP (from the computer) requests to the printer and the answers SNMP from the printer to the computer.  This status of probable reports in near real-time.

  This isn't a problem, but I would like to discuss the volume of network traffic.  I see on request 20 and 20 responses per second for a single computer.  Request/responses start a port 1026 (sending a request and get an answer) then increment to the next port 1027 (request / response), increment to the port 1028 and continue.  This continues until it hits port 5000 then begins to port 1026.  About, through 4000 ports every 3 minutes.  Each request and response being about 100 bytes of information.

  This traffic volume is normal?  It can be reduced?

  I looked in the printer and the software congifurations to see if it can be reduced to a minimum and can not see a framework to reduce the traffic.

  Well, I expected someone to complain about this. Also, I think that it is rare as well.

  What you see, is the HP SW on each computer to the printer for admission to the status of vote. I think that changes of the PC port with each SNMP request but you should see that all SNMP packets going to port 161 printer and that the printer meets the port 161 originally PC port...

  You'll also see shows SLP in 427 on the printer port as well (most used ARP and NETBIOS stuff).

  To my dismay, this is normal (an old design in fact) and we are changing. Yes, it's a chatty Protocol but the bandwidth network should not be significant (using your numbers – I thought the refresh frequency was 1/3 Hz):

  5 computers * (20 packets/SNMP-s) = 100 packets/SNMP-sec * 200 bytes/SNMP-package (estimated) = 20000 bytes/s.

  (Is this a lot on a 11g wireless network has a bandwidth of?)

  The real problem occurs when you have a wireless network. Because UDP is not reliable, the SNMP get s/SNMP-response may be lost, especially on the airwaves. When this happens, the SW will attempt the request again, and after a series of delays, the HP SW will think the printer is offline.

  Now to answer your original question: you can remove the most background traffic by disabling the HP printer services. You will still be able to print but the scan will not work. Another option is to uninstall the HP SW and manually add the printer in Control Panel. Unfortunately, this also gives you printing without analyzing.

• How can I correct gateway is accessible, but cannot receive network traffic on internet

  I have a Windows 7 laptop. All my drivers are up to date. It happens every 10 to 15 tion.  When problem he pulls it only resets my wifi. Then it will happen again. I reset my router already. I pass the channel for my wifi. I have uninstall the anti-virus software.  I'm stuck here please help.

  How do i fix gateway is accessible but cannot recieve network traffic from internet
  

  Hello

  I appreciate the efforts to try to solve the problem. You might face this problem because corrupt or the network driver. You could also face this problem because of the incompatibility between the IP address. Please write us with the following details.

  1. What is the brand and model of your computer?

  2. You did it all changes to networking prior to this problem?

  3. Do you have an error message when you try to access the Internet using a browser?

  I suggest you follow the steps below.

  Method 1: Run the network troubleshooter utility.

  Click on the link below and run the network troubleshooter utility. Automated convenience store is a tool that can find and automatically fix problems with your computer. These utilities are not designed to solve all the problems, but they are useful to try because they can often save you time and effort.

  Using the troubleshooter from network in Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Check the question and proceed to the following method if you are still having problems.

  Method 2: Try resetting the TCP/IP stack.

  Click on the link below and follow the steps as for Windows 7 in the section I would like to fix it myself.

  How to reset TCP/IP using the NetShell utility.

  http://support.Microsoft.com/kb/299357

  You can also follow the steps in the tutorial below. It contains the methods of troubleshooting issues related to the network database.

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win81tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Let us know the status of the issue and the details asked. We will help you.

• Virtual network traffic control

  I am currently evaluating different virtualization products and have a special interest in virtual machine network traffic control.  What I want to know is: is it possible, in VMware Server (or drive), to completely control the network traffic between virtual machines?  In other words, can I programmatically control the virtual network so that I can decide if and when, a bunch of VM #1 is passed to VM #2?

  I had planned on using network invited only, but if NAT or Bridged Networking is necessary to make this work, I'm ready to do.

  Thanks in advance,

  Dan

  Is it possible, in VMware Server (or drive), to completely control the network traffic between virtual machines?

  N ° Server VM Ware or player has no such controls.  ESX has traffic shaping.  None of these can do however to balance INCOMING traffic load.

  You would need a virtual computer with the software between them to control data.  But if you do, upgrade to ESX Enterprise Plus with Cisco Nexus.

• ConfigFree network traffic meter - what do the bars?

  What does the bars up and down the network traffic meter in the configfree SP2 version?

  Hello

  Unfortunately, I m not sure what bar do you mean but the ConfigFree includes a feature to help clean with lots of useful information and helpful tips.
  Please start the Configfree and press F1. Now, aid should start.

• Satellite A110-195 PSAB0E crashes using NIC for network traffic

  The problem is that my A110-195 crashes when you use the onboard LAN for network traffic.
  I have search the forum for this kind of problems and I found two themes on this topic.

  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?MessageID=93924𖻤

  There's no solution for my problem in both entities.
  I tried a lot of pilots of different sources and developers but the problem remains.

  It is really very annoying. Please help me with this.

  Hello

  You have a Realtek Lan card?
  If Yes, then you should contact the ASP in your country for a fix.

  I had a similar problem with my card Realtek Lan on a Satellite A110. From time to time my system locked up for the big copy via the port LAN Realtek.
  I talked to a local technician and he said to a patch.

  Unfortunately, I put t know what he did, but after the update (or install the fix) I didn't noticed the same problem again.

  So I recommend to contact the authorized service partner and request the hotfix.

  Good bye

• Can not activate my Network Magic software after reinstalling

  After a clean install of Windows 8 Pro I installed my Network Magic Software. After installation, I tried to activate my legal version, but it will not accept a connection to save and activate. I discovered that Cisco supports more Net Magic then activation is not possible in the Netherlands. Cisco said that there is no other tool network of Cisco for my WRT-320N replacement and other Cisco devices. Is it possible to activate my Network Magic software in another way (in the United States or in the registry of Windows or Network Magic)? THX Martin

  One of the reasons why software cannot be installed are because of the firewall on your computer or antivirus software. Try to disable the firewall or disable your anti-virus temporarily and activate Network Magic again.

• You are looking for a free network diagram software

  Hello

  You are looking for a free network diagram software

  Like this program: Edraw network diagram , but it is desirable for free. I want to draw physical Cisco network architecture detailed diagrams. With Cisco models logical network diagrams and drawings of the architecture of our office network (2000 users).

  Good day

  Vania

  Unfortunately, this community forums are for devices Cisco-Linksys (SOHO) home-network. The Cisco Catalyst WS-C4507R unit is managed by the Cisco Small Business support community.

  Please click here for plu answer your concern.

  https://supportforums.Cisco.com/index.jspa

  OnnagokorO

• Linksys Wireless Network Monitor Software

  I have Wireless-G Notebook Adapter v.5.0

  Need help to locate Linksys Wireless Network Monitor Software.

  I bought the Wireless-G adapter for 3 years ago and recently lost HD Crash.And software, I know that I have the disk somewhere, but cannot find it... still looking...  I tried looking for Cisco and could not find it.

  Any advice?

  Thank you

  
  

  

  I found it!, online.

  http://homesupport.Cisco.com/en-us/wireless/LBC/WPC54G

  THEN

  On the tab for:

  DOWNLOADS

  then SELECT BOTTOM LIST drop-DOWN select hardware version.

• Wusb54g v2 - problem with Linksys Wireless Network Monitor Software

  I have a card Linksys USB wireless (WUSB54Gv2) that is currently used with an old HP Desktop running Windows XP Service Pack 3.

  I also have a Linksys Wireless PCI Adpater (WMP54Gv4.1) that is currently used with an old Dell desktop running Windows XP.

  I have a wired and wireless home network... My broadband provider is Verizon FIOS; I use their supplied router because the coaxial cable that provides the internet connection plugs only into their wireless router, not in a modem and a router. I have an encryption key for 128-bit WEP on the side of the network wireless; It is even once managed via the Verizon FIOS router via a web browser (like most routers).

  Two other computers I own are a desk custom-made to date with a direct link to the Verizon router and a laptop from Apple. These two computers are NOT having internet connectivity problems.

  I've updated to the latest drivers for my USB adapter and the car PCI.

  ---

  Here's my problem:

  When I try to connect to the internet using the Wireless Network Monitor software provided by Linksys, computers, I can connect to the "access point", but not internet. This product only when I don't have the key WEP 128 bits in place, when security is disabled.

  If I right click on the Wireless Network Monitor icon in the taskbar and select "Use Windows XP Wireless Configuration", enter my network through windows manually information (including the WEP key), I can connect to the internet perfectly.

  However, when I restart or stop two PC, the Linksys Wireless Network Monitor reactive software itself, where it automatically attempts to connect to the internet, but fails, after which I right click on the icon of the monitor again and select «Use Windows XP...» "and then I connect to the internet.

  Is anyway to disable the Linksys continuously monitor software WITHOUT uninstalling the software or drivers? (I tried this; Windows cannot use or recognize the network adapter).

  ---

  I might just re - activate the Setup Wireless Windows XP every time I close / restart, but other users of PCs on my network (my family) are exceptionally illiterate computer/network and would not be able to learn how to do whenever they want to connect. There is very little practice.

  If there is a way to solve this situation, please help! If all goes well there are other solutions I am open to suggestions.

  I must emphasize that our Apple laptop connects fine when the WEP key is set.

  Once more, looking for quick help!

  Thank you advance!

  Remove the Linksys adapter and uninstall the Linksys software menu programs... Re - install drivers insert the CD of Linksys install in your CD-ROM drive, when the welcome is displayed click on exit, connect your USB adapter now... When the Hardware Update Wizard window appears, click on install the software automatically (recommended) and then click Next... Click Finish when the installation is complete.

  NOTE: The hardware installation screen may appear indicating that the adapter has failed the Windows Logo test. Ignore the window and click on continue to continue the installation because the adapter has been tested and it works with Windows XP. When Windows has finished installing the driver, click Finish.

  Click Start and open the control panel and double-click on network connections. Right click on wireless network connection, and then select view available wireless networks "-If you see your network wireless in the list, the highlight by clicking 'single' on it now, click on the 'Connect' button below-if your wireless network is secured, it asks you to provide the network key - provide the wireless network key and confirm again in the confirmation box and click 'Connect'." It should work...

• How to monitor and lock the network traffic

  I am connected to a network that is always connected to the internet. I needed to display the bytes sent and received and also to block network traffic by not using only Internet. (Vista)

  Hello

  There are some send receive info on the status screen is in the Conncetion Local adapter.

  Look here to the right, http://www.ezlan.net/Win7/status-nic.jpg

  If you need something more complete this freeware is very good, http://www.softperfect.com/products/networx/

  Regarding the disconnection of the local network.

  If your computer is not configured for sharing, then it cannot connect to from the local network first.

  If not, right-click on the network map, and then click on turn off (do the same after to activate).

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Please recommend network management software

  Hello!

  I need help to find a network management software that is compatible with our switches. I use a network with Cisco/Linksys managed switches:

  10xSLM2008,

  5xSRW208,

  2xSRW2008MP,

  1xSF 300-08

  I was hoping there is management software (not the thing webview/web browser), that could do these things (in order of preference):

  -connect to these SNMP (or similar) to show me a little statistics on each port on each switch, as well as the connectivity between these switches.

  -I would like to know which port what mac addresses and possibly the IP addresses of these.

  -Let me know what mac addresses uses more bandwidth

  -ban a mac address

  I'd be happy if someone could give me advice on what software to buy.

  Best regards

  Lars E Fodnes

  SolarWinds NPM - http://www.solarwinds.com/products/orion/info.aspx

• analyze network traffic

  Hi all

  first of all, I want to say hello and that this forum was already a big help for me.

  Unfortunately I could not find anything on how to analyze the network traffic on a blackberry device. It is possible to analyze the network (ip) traffic using an api (signed) java?

  Something like an OutboundMessageListener for IP packets would be perfect. What I found was net.rim.device.api.system.RadioInfo.getNumberOfPacketsSent (), but I want to get the content of all sending packets (ip). Any ideas?

  Thanks in advance,

  Steve

  not possible, unfortunately.

• total number of bytes of network traffic for a given period and given a vm guest

  Hello

  I want to see the total number of bytes of network traffic a given virtual machine generates in a give period.

  I think it's possible with a great metric but don't know how.

  Any help is welcome.

  Kristof

  This is for vrops x 6

  1. create a metric configuration

  
   
      
  
          
          
          
      
   

  2. create a new dashboard with a list of objects and graphic metric

  3 edit the object list widget, and the filter object type\Virtual Machines and save

  4. change the metrics graph and select the metric config that you created in step 1 in the metrix configuration box and save it

  5 in Widget interactions select list of objects in the menu drop-down and click on apply Interactions and save the dashboard

  When you open the control panel and select a virtual machine from the list (or search for it in the filter), it will display the average amount of data received and transmitted in Kbps in the metric table. Use the controls to date to specify when you want to see the data to and from.

  Hope this helps

• Asked to "monitor all network traffic" Fusion 7.1-8.1 Windows plain vanilla VM - I didn't ask for it, how to disable it?

  Hi all

  I created a computer virtual Windows 8.1 on October 1, 2013 with the current, at that time version of VMWare Fusion (not Pro, who has the tab network preferences and the check box associated to whether to display it's fast) on my Mac.

  Since then, I upgraded the version of OS X to Yosemite and the version of VMWare Fusion to 7.1.1.

  At one time, months or years, I started having the prompt below:

  

  A virtual machine tries to monitor all network traffic, which requires administrator access. Type your password for this purpose.

  I don't want to allow this, I never asked for this virtual machine to use the "Promiscuous" mode, I don't want to do, and I can't find anyway to turn this off!

  I always leave the command prompt and everything works fine.  Discussions only I can find this in the forums are all related to people using ESX to vSphere, neither of which I have no knowledge where all used.

  I had an another VM Windows 8.1 on another Mac during the same time, which has crossed all the same updates, and it never shows this prompt.

  Please help make this stupid, quickly go and stop this virtual machine to try to use the "Promiscuous" mode!

  Thank you - Harold

  You have the Hyper-V role installed in the virtual machine?