'New' BEFW11S4 ver 4

Similar Questions

• Losing the history with the new Firefox Ver 10

  I'm angry that FF seems to update versions without any warning, that is to say I have no word to say as to when I have to spend extra to deal with a new 'look' / version. It is inconsiderate to the users as we do not always have free time at a time that suits to the FF.
  How can Q: I:
  (a) ensure that the FF does not give me a new version unless I ask you?
  (b) when he gives me a new version, always my complete history with her? (I regularly use 'history' as a memory audit trail.

  With this worm 10 I lost so much time as:
  (a) he lost my historic trail and Windows I left open specially
  (b) and 'help' suggested I have restart the laptop to see if it could re - finding the story - he could not
  (c) new versions we said this, look how pester on it, sometimes I'm just to busy at this time!
  Wow! -See all troubleshooting information that can be supplied with this question - impressive.

  Fast, comprehensive and very helpful - thank you. The 'advanced update' bit already fact (would have taken me a while to find - and if I knew that these were!), let Xmarks until later... Thanks again

• Acer V5 471PG, new bios ver 2.15

  I saw the new bios 2.15 for V5 471PG

  What is new features /improvement of 2.13?

  All impact / dangerous if I upgrade from 2.13 to 2.15?

  It's a generic update with some new brackets for material but nothing major.

• Help with BEFW11S4 ver. 2

  My Internet works on the host computer, but my client computer cannot connect to the Internet. The host includes Windows Firewall (I am running XP on both computers) and when I check the network connections it says that the connection to the local network on the host computer is connected but firewall. My client computer, which also has the firewall turned on as well as Norton AntiVirus, has an error message after the restart: "Linksys Wireless Network Monitor: Access violation at address 00425EB5 in module"WUSB54GS.exe".» Read of address 00000368. "When I look at this subject network connections, the wireless connection is disconnected. Note that this problem occurred recently, in front of which Internet worked well. So, what's the problem? Thank you.

  Solved. It does not solve your solution, but what that did was to buy a new router and adapter. It has been for a long time.

• Problems with new cable modem and router

  Long story short, that my cable modem went bad.  I replaced it.  Now the two computers cannot connect to the internet.  It gives me a DNS error, saying that they can not find the server.  However, I can get on the internet if I hang the right modem to computer with courses through the router. I got it with the new modem a few days of work and use of the router, but now it does not work.

  There are 2 computers on the network, the two runnning vista.
  a linksys router model number BEFW11S4 ver 4.
  and the motorola surfboard SB5101 modem.  the old modem was a surfboard SB5100 motorcycle.

  There's a btn reset on the router (often the metal clip through a pin hole)
  Everything also its possible allways the router is bad

• DesignJet 4500: HP DesignJet 4500 driver ver.7.10.0.0 - unreadable symbols in the printer options window

  Hello, I have a problem with HP DesignJet 4500.

  With the new driver ver.7.10.0.0 (the most recent in the HP support page), when I get to the printer options - all symbols are unreadable (screenshot 1).

  Old print server - I found already installed ver.6.17.0.0 driver 32-bit and 64-bit driver ver.7.10.0.0 (screenshot 2). When installing 6.17.0.0 driver for 32-bit PC and open the window-it works very well, all the symbols are in English (screenshot 3).

  So, how do I make the symbols in 7.10.0.0 readable? Or, if I can't fix it, where I can download 6.17.0.0 driver (64-bit)?

  Thank you.

  P.S. It's unreadable that symbol in the windows printing options, but 7.10.0.0 prints correctly.

  Screenshot 1:

  

  Screenshot 2:

  

  Screenshot 3:

  

  Hello

  Remove the driver completely from the computer (devices and printers, properties of the server), download the driver from the HP website and install it.

  If you still have the problem, you may need to remove the printer from the registry.

  Best regards

  Mike G

• BlackBerry Smartphones showing whatsapp new message in the main message Inbox

  How can I show Whatsapp new message (ver. 2.6.2970) in the main message Inbox?

  Now I have to go directly to Whatsapp to read new messages while for the messenger bb can read/write directly from my message Inbox.

  Cool!
  I'm glad that you fixed it.
  Please solve the thread so that others can find your answer faster.
  Thank you

  Bifocals

• Support of the shared Variables in the third part XP embedded based of PTC?

  I sent a request in an embedded XP touch function (third party). The application works very well, but hosted on a RT (sbRIO Board) shared variables are not getting updated in the app on PTC

  1. the PTC is part of the project as a Windows XP Embedded Touch Panel

  2 NI TPC Service has been installed on the PTC and the application can be deployed remotely from the PC development via ethernet. (Where network connections and communications are OK)

  3. using distributed in the development computer systems manager, I can see that the shared variables are getting updates on the network

  I think that the problem can be solved if the following programs are installed on the TPC

  A. Support for variables that are shared for XPembedded

  B. shared Variable engine

  I tried to install the support of variables shared Program Files > National Instruments > Labview 8.6 > PDA > utilities > Variables > x 86 - but I get an installation error "cannot find the application for the Pocket PC applications Manager.

  Shared variable engine was installed from the ve220 folder. The program is installing. But the engine Variable is not start Control Panel > administrative tools > Services, Xpe, the service is stopped and cannot be started. When I try to start the service, I get the following error on PTC

  "Cannot start Service engine of National Instruments Variable on the local computer."

  Error 1053. Service has failed to demand launch or timely control.

  Please suggest solutions to the addresses above or another of the following:

  1. support of variables shared for XP built-in PTC

  2 Installer engine Variable shared.

  Thank you

  Krish

  Problem solved!

  Update for interested people working on XP Embedded PTC

  Just to ensure that shared Variables were indeed accessible to the TPC, I wanted to install Distributed Systems Manager 8.6 on the TPC. However given that the TPC was only 1 GB of DOM (disk on memory) and with all the software that I had tried, there remained only a few megabytes on the system. I had to add an another DOM of 2 GB.

  All products in the Installation went well, with the exception of the Logos NOR (Version 5.0). Logos OR installation has failed repeatedly.  I tried to install NI Logos separately, with the same results. Then I had this intuition that NI Logos had anything to do with the question.

  Then, I downloaded the new version of NI DSM 2009 SP1. Even if it were to settle on any fresh system without Labview, the installation would not proceed beyond the stage of configuration. I tried to install NI Logos of the folder on the download of new products separately and it worked magically!

  Once the new Logos (Ver 5.5) installed, the Shared Variable engine starts automatically and the shared Variables are finally unleashed - free stand up and shine! I thank Almighty God!

  On the lighter side, come to think of it - to run an application about 400 KB, we need NEITHER of Run Time, XP embedded, DSM, Logos...  (around 900 MB). Can make us everything simpler?  Invite your comments...

  Thank you

  Krish

• WRT160NL Usb storage not recognized after update firmware

  Hello.
  I use a power running alternative disc into my router for a long time, until I've found the new firmware (Ver.1.0.04 Build 2), but after the upgrade of the storage was no longer working. (I don't remember the firmware version he had)

  In the storage, in the page Setup tab, I can see the drive, I can create shares, but these are not present in the windows network. (I use windows 7)

  the disc has been tested using FAT32 and NTFS (232.8 GB)

  you have a solution for this problem? or should I return to the firmware version, he had (that I don't remember)...
  y at - it another version to switch to?

  Thanks for your help...

  Yes! This is the solution!

  Thank you

• utility based on the Web shows again the old version of the firmware - HELP PLEASE

  In September of last year, I replaced my old Linksys with a new (BEFSR41 ver 4.3).  I started to get in trouble yesterday, so I consulted the web-based utility and noticed that the window says: the firmware 2.0 version!

  I tried to update to the latest firmware available for my model, following the instructions on the site but something went wrong and the firmware has been altered. Finally, I managed to update the firmware via tftp utility, and he said that the upgrade has gone through. But the utility still shows the version of the firmware 2.0.  Under the router > status reads as follows:

  Capture (share.field_33_UI_share) Firmware Version: 2.00.4 build 7, January 20, 2010

  I am very confused. Which is the latest firmware or I get it confused with the 4.3 version number?

  I really hesitate to update the firmware again after the problems I had the first time.  If anyone can give me some advice on what to do, I would really appreciate it.

  You confuse the hardware version of the router with the version of the firmware.

  The BEFSR41 is the model. One physical versions of this model. Each version contains a different material. The exact hardware version is printed on the label under the router.

  The firmware version is the version of the firmware (software) running on the router. It is important that the firmware used is compatible with the hardware version of the router. For this reason, you must select the correct hardware on the router Linksys support download site version to be sure to choose the right firmware compatible with your router.

  The latest version of the firmware of the BEFSR41 v4.3 is Ver.2.00.4 Build 7. You have the latest firmware.

• WRT610N connection to the provider ADSL (PPPoE)

  I started the installation of the router WRT610N wireless dual band replacing an old LINKSYS BEFW11S4 VER.3 Wireless Access Point Routerconnected router to a DSL modem.

  The provider of Internet connection must be configured with the PPPoE settings.

  I configured the same parameters as the BEFW11S4 in the WRT610N, but I never had the Internet connection.

  I'm sure I used the same settings as before, but it does not work.

  What could be the problem?

  If you need configure your router for PPPoE modem must be configured for fashion...

• Manager certificates 're-record of lstool' failed: 1 / VCSA Certificate Manager Option 1: certificate to replace Machine SSL with certificate custom

  As a result of this post...

  Configuration of VMware vSphere 6.0 CA VMware as a subordinate certification authority

  .. .we have now installed a brand-new VCSA. This is a clean install.

  "In accordance with the recommendation of support, I am now trying to do ' Option 1: certificate to replace Machine SSL with certificate custom" using a Microsoft CA

  This is the error message:

  2016 07-13 T 15: 24:25.268Z of INFORMATION serial number of the certificate manager before replacement: < redacted >

  2016 07-13 T 15: 24:25.268Z of INFORMATION: < redacted Certificate Manager after replacement serial number >

  2016 07-13 T 15: 24:25.268Z INFO-Certificate Manager footprint before replacement:< redacted >

  2016 07-13 T 15: 24:25.268Z INFO-Certificate Manager footprint after replacement:< redacted >

  2016 07-13 T 15: 24:25.268Z certificate MACHINE_SSL_CERT certificate INFORMATION-Manager replaced successfully. Serial number and the fingerprint has changed.

  2016 07-13 T 15: 24:44.90Z ERROR-certificate error when replacing Manager machine SSL Cert, please visit /var/log/vmware/vmcad/certificate-manager.log for more information.

  2016 07-13 T 15: 24:44.91Z "lstool record" has no certificate ERROR Manager: 1

  A pension case is ongoing. But if someone has any ideas?

  <>rant

  It is incredibly frustrating that something (replacement of a SSL certificate) that should be so simple is so hard.

  It's extremely annoying to know that the Certificate Manager is able to completely screw up a VCSA.

  How VMware is justified in the marketing of this new approach ver.6 as a 'simplification' of the management of SSL certificates?

  < / end of rant >

  Thank you

  Robert

  This has been fixed by an Incident of Support VMware

  I don't know how to fix them, but it took over 2 days (except "waiting for a response" time)

• Problem with IBM Thinkpad X 40 (disconnection |) WiFi)

  Hi all

  I use IBM ThinkPad x 40 with XP Pro SP3 x 86. I have the latest drivers for my laptop:

  Wireless driver LAN 2100 3B: driver - 02.08.2006 date; Version - 1.2.5.37
  LAN Driver 1000 MT Mobile connection: driver - 20.08.2008 date; Version - 8.10.3.0
  My router is Linksys WRT 320N, using new firmware: Ver.1.0.05 (Build 2) from 14/12/2011

  Note: The problem (the issue of sectioning) only occurs during downloding, video streaming, only when the connection is fully "charged".

  I use my router with many other features wireless (also ' i' devices) and I do not suffer the same problem.

  I hope that you will be able to help me.

  Kind regards

  saketo

  Hi Alexander,.

  I don't think that it's such a compatibility problem, as far as the card in the x 40 is a speed card B.  By today's standards, it is quite slow.  Don't get me wrong, I love my x40s.  But, one of my friends had a speed card B in it and she would lose the connection on a regular basis.  I put a map of 2200 BG in it and had no more problems with the connection and the download speed has increased significantly.

  Edit: Your 40 x can also draw a 2915ABG wireless card.  Scroll the Maintenance Manual of material for list items and there is one for Europe.

  Here is a link to the Manual of Maintenance of equipment .  Page 81 shows the wireless card.  It is very easy to change, only 2 clips and 2 antennas, and these cards are real cheap these days.

  Or, you can just use a USB wireless adapter to connect with.

  One thing you can try if you are using xp has to go into Device Manager, right click on the wireless adapter and click Properties.  Click the Advanced tab. Make sure the transmission power is set to the highest and feeding management is the highest.

  If you use the Intel Proset software, make sure the Intel throughout the improvement has the highest value.

  Dave

• File size a massive increase in Captivate 2

  I just finished reviewing a manifestation of the old.
  
  1. the old film, worm 1.01.1418 (42 slides), is 36, 900ko.
  2. the new film, ver 2.0.0 (57 slides), is 338, 638 KB.
  
  Both have audio, notes, text captions, and highlights.
  
  The only big change is that we use the new captioning function.
  
  Someone else has met and solved this problem?
  
  I don't think that I can break it in enough segments without making end users lose interest and I think I have to Snag Screenprints and recreate in Adobe Presenter.
  

  Captivate support found the answer to my problem and it is in the LIBRARY of the current file.

  With the .cp file opens and the LIBRARY pane visible, look at the toolbar of LIBRARY.

  1. Select the tool SELECT the UNUSED ELEMENTS.
  2. THE ITEMS will be highlighted in blue.
  3. Select the REMOVE tool.
  4. prior to the economy, overview of the project (F4) to ensure nothing necessary has been deleted (just a small step paranoia)
  5. close and exit to check file size reduction.

  Reader Digest Version: prior to publication, to delete unused items.

  Note: If you try this and it solves your problems, send praise to Bruce Chizen, CEO of Adobe.

  We strongly believe in for Training Solutions Adobe products (presenter, Connect, Captivate, Robohelp and soon CS3) and encourage us to use throughout our society. When I expressed my frustration of not being able to contact support in due course on this issue, Mr. Chizen came through.

• "Use current Page" to save the Home/tab pages is gray, even though I have a new install of ver 22 without adding plugins or extensions. How can I fix it?

  When I try to save my pages / tabs, I can not, because this option is grayed out. I even uninstalled FF with Revo Uninstaller completely reinstalled without new plugins or extensions, and it remains greyed out. The only thing I can do is pin the tabs, but I wish to use this option. If I can't, I don't know whether its Firefox or malware or? Thanks in advance for any help. Windows 7 family Premium SP1, Firefox ver. 22

  Thank you very much for your time and effort. It was not the solution, but I couldn't find a place to close the ticket/request. I discovered that I had pinned tabs, in doing so, it grayed out this option. Once I have this marking tabs, I was able to use the option ' use current Page/s. Thanks again for responding so quickly.