No noise in the right of the eMac G4/1.42 Ghz channel

Similar Questions

• The E3000 does support 5 GHz channels > = 149 or only 36-48?

  Hi, I have read various messages of the forum saying best performance of a wifi router, you must use the channel 149 or MORE and only 36-48 have a lower signal strength and therefore less range and speed.

  I live in New Zealand and when I select the drop-down list for the 5 GHz band wireless channel he mentions only 5 options - Auto (dfs), 36, 40, 44 and 48. I read the posts of the forum of people saying you should switch to 149 or more and I saw some screenshots showing the drop-down list with 149 selected. But I did not have this option.

  If I check status > Wireless page, it shows that the channel 36 is used (for automotive).

  I'm doing something wrong? E3000 in this part of the world do not support 149 etc.?

  I spoke in a live chat with a support representative who told me that all the E3000 are the same everywhere in the world and there was little or no difference between them in the firmware. I was also told that 36-48 strings are high gain and so there is no need for other channels, which contradicts the other articles I've read what 36-48 state are weaker channels.

  Can anyone shed light on this sone?

  Thank you.

  It is forbidden to put an access point wireless statically on a higher channel. All channels except the four listed should be used with DFS.

  See http://homecommunity.cisco.com/t5/Wireless-Routers/E4200-5ghz-channels/m-p/393155

• The WGA600N can switch between 2 channels?

  I hope that I am not on something, but I can't find an answer to my question.

  I have the WRT610N simultaneous dual band router paired with a WGA600N wireless dual-band adapter.

  With the router, I set myself to 2.4 and 5 GHz channels separate SSID and WPA2 encryption keys.  My adapter, although it can 'see' the two networks, connect only to one. On the product for the WGA600N support page, it says clearly, "dynamically travel channels and wireless networks based on the quality of the actual signal and a link for maximum availability and reliability of connection."

  My question is... How can I activate my game card work on the 2.4 and 5 GHz channels to find the best connection?  It seems in the WGA600N Setup, it makes me choose a channel.  Both channels on my router must be on the same SSID and the same encryption key for the adapter to switch back?  Should I switch to WEP mode?

  On your Linksys card, only a single frequency could serve both (2.4 GHz or 5 GHz), although it could pass the frequency... Access your game card and go to the Wireless tab on the Basic tab, select 802.11 2.4 GHz and 5 GHz band... 802.11 mode should be mixed 802.11na, 802. 11A, 802.11ng, 802.11 g, 802. 11 b, let the rate of automatic transmission and channel width should be 20/40 MHz...

  Be sure to set the security WPA (not WEP/WPA2) wireless...

• Camileo H20 - strange noise throughout the video

  Hello.

  I today received delivery of my first camcorder, which as the title suggests, is a Toshiba Camileo H20.

  Overall, I am impressed with this little camera, but there is a problem that concerns me. After reviewing a video of test, I created to see what the quality was as I noticed a strange sound throughout the video. I struggle to describe, it's a bit like static/interference. The thing is that I already have some tests to find out what could be the cause of it, and I found nothing. Again, the camera records audio as usual, but this static/interference is there with her.

  At first I thought it's maybe because I'm close to electronic devices such as a TV and a PC, so I went in my new garden and filmed there, but noise persists. Then I covered the microphone to see if it makes a difference, but it didn't. I also tried different video modes, leaving the camera on a desk to record walking around a room and then I even resorted to transform a sound recording off altogether. The strange thing is that the camera has always been that noise when I play the video on my computer even if no sound is registered.

  I have a slight suspicion thinking he made this noise if the camera is moved. But if I remember correctly it makes the same noise when it was not moved on the desktop.

  Someone at - it ideas on how to solve this problem? Preferably not by reference. I would like to, but I don't have time because I'm going on vacation next week and I want the camera to do this.

  Thanks in advance.

  I'm downloading two videos on YouTube in VGA mode and 720 p. Once they are uploaded I will edit this post with the links.

  HD:
  http://www.YouTube.com/watch?v=EqxzQi5G0Sc

  VGA:
  http://www.YouTube.com/watch?v=9fMjfIqK09Q

  Quality cannot be correct because they have just the end of the download.

  Hello

  I have no idea why this strange sound appears, but I found in the manual of the user an interesting point.
  You can disable and enable the sound of keyboard and operating noise.
  In Submenue setting, press the button to go to the audio menu. Use the left/right keys to select ON or OFF. Press the menu button OK to validate the settings.

  The other point is that you said that this noise appears when you play the video on your computer. Maybe it's just a s codec problem.
  I remember that the sound on my movies created with the HD cam is really strange questions wore on the package of codec missing on my laptop. In addition, the player didn't manage HD sound.
  I chose the stereo settings and then the sound was ok

  I'm not very well if this might be a reason in your case but it s m worth a try
  Check the sound configurations and try to install some codec packs too

• 6035-E high frequency noise reduces the resolution of 14 bits.

  Dear Technical Support Group OR and MF DAQ,

  I don't get the complete 16-bit on my DAQ 6035 - E cards and 6034-E resolution because of the high frequency noise.
  The Test Panel and the actual catches show 1.2 mV peak-to-peak noise with entries is is failed the GA right input in differential ended mode and single connector - Test Panel screen grab and connector attached picture.
  With a range of +-10V, noise LSB + half expected specified in the manual should be only 305 microvolts (20/65536) which is four times less than what I see.
  So far, I've been scanning (a channel) to ten times (60 KHz) the rate I need (6 KHz), then SavGol the filtering and sampling downstairs.
  The problem is that I need to sweep the four channels that now exceeds the capacity of 200 KHz of the card and also results in huge quantities of useless data.

  Have considered buying a new USB DAQ with better record, I fear that all products OR suffer the same flaws and gave the purchase.

  Please, share your ideas.

  Thank you.

  GPSman salvation,

  Looking at your control panel test plot, it would seem that there is a discrete steps on your axis is between - 0.0019 and - 0.0012 or 700 µV.  Then you can see that there is about a little more than 2 discrete steps to your signal, which brings value to about 300 microvolts, exactly as the resolution makes clear.

  You can also find that there is a specification of noise and precision in specification.  You can find for a single point, the accuracy in the +/-10V between 1,085 millivolt.  This is on page 4.  This would allow your signal of +/-1 mV of the expected value, the test also indicating panels.

  Does that help?

  best,

• PCI-6733 signal noise when the computer screen is plugged, the weight on the case

  Greetings,

  I hope that it is in the right section.

  Card: PCI-6733

  I'm a 60 Hz, 2 mV peak-to-peak with a compensated 2.4mV noise when the monitor is plugged into the VGA port.

  Same card in a second computer, problem is more serious, 4mV Ridge to Ridge, 4.3mV offset. When I push on the case near the power supply the offset rises from a few millivolts.

  The two computers are running the same exact versions of software and drivers. Dell and quite similar to each other in both material and form.

  I have a third computer that noise coming out of the map is horrible no matter what.

  I exchange business cards and the problem is with the computer, does not follow the acquisition cards.

  No idea how to solve this problem and what is the cause?

  Thanks for any thoughts!

  -Michael

  Tall_Michael,

  Looks like you may be plugging your monitor and your computer in different points of sale.  If this is the case, this is probably the cause of your noise and can be eliminated by connecting the two devices on the same socket.

  Here are some articles that deal with the noise you are experiencing and various workarounds in the cases where what I mentioned above are not the case:

  The problems of noise in the measurement configurations

  Sources of the measuring Signal ground

  How to eliminate noise on measures DC power without using a lowpass filter of material?

  I hope this helps!

  Thank you

  Trey C.

• I have UN-plugged my speakers and replaced by headphones. Noise if the headphoens is fine. I now want to put the spekares back in, but there is no sound at all

  original title: SOUND

  I have UN-plugged my speakers and replaced by headphones. Noise if the headphoens is fine. I now want to put the spekares back in, but there is no sound at all. Can anyone help?

  So they are pregnant Dell with standard 3.5 mm USB powered plug (* and even the green port plug in as shown in the picture)?

  Therefore, the USB plugged into the port in the back of the computer for power to the speakers?  Try a different USB port - just to see if the chosen one does not provide the necessary power.

  Make sure that the speakers are turned on and the volume is turned all the top (to the right).

  Make sure that the sound output is not cut on your computer (plug in the headphones to check what you mean by them.

  Plug the 3.5 mm of the speaker to the green port on the computer (see photo above.)

  If you don't hear sound... Unplug the plug 3.5 mm and touch something metal - static electricity?  The speakers become power at all?

• Tecra S1: Notebook generates noise when the LCD display is on

  Tecra S1 is 4 years old and generates a high noise when the LCD is turned on (from last week). The noise comes most of the keyboard. Could this be a defunct ups?

  Is there an easy way to fix it? It's not very loud, but in a quiet that is audible.

  Hmmm I think this noise comes certainly from the FL inverter.
  But I can't tell if the inverter is faulty or not because I noticed that her top on different laptops when the brightness of the display is placed on the lower floor.

  But if you think that this problem was not present in the past, then you need to contact a technician who could help you replace the inverter FL.

  Best regards

• If I click on an email link in a web page instead of an empty message is opened I still get noise toward the top of the screen with a log-in for googlemail. I don't have and won't have a googlemail account. I just want to be able to send e-mail messages b

  If I click on an email link in a web page instead of an empty message is opened I still get noise toward the top of the screen with a log-in for googlemail. I don't have and won't have a googlemail account. I just want to be able to send e-mail messages by using Outlook.

  See this article.
  
  http://support.Mozilla.com/en-us/KB/changing+the+e-mail+program+used+by+Firefox

• Camileo P100 screen is black, but the noise from the unit

  Hi all
  I just bought a Camileo P100 and fully charged.

  Although it seems to work when you take a picture the camera 'clicks', the video recording the LED flashes, the touch screen is black and I don't see anything.

  When you touch the screen, it doesn't seem to be working (there are noises from the unit when I touch the screen), but the screen is black.

  Can anyone help?

  Thank you
  Mark

  Hello

  Try, press and hold the button On / Off a few seconds.
  Also check if the opening of the camcorder is open

  But it looks a bit like a hardware problem.

• Satellite L500 and the noise of the fan

  Last week, I bought a new laptop Satellite L 500 with Inter i3 processor, 1 GB, 4 GB of ram ATI graphics card, etc.
  Everything is OK in general, however, I think the fan is very noisy.

  I used to own a HP Pavilion laptop and could hardly notice the fan while with my new laptop, the noise of the fan is really loud.
  Does anyone know if this is normal or if it could be fixed somehow?

  I did some internet research for a solution, but I couldn't find anything, and apparently nobody complains noise from the fan on L 500 computers portable so maybe it's only me that have this problem?

  Thank you.

  Stefano

  For optimal use for laptop use the balanced power plan. Go to the advanced settings for this plan and energy saving of Toshiba, you can find cooling method.
  The level here. I'm sure that notebooks fan will be much quieter than before.

• Equium A100-147 - clicking noise from the HARD drive

  For awhile, I had clicking noise from the HARD drive and when the laptop could not, I assumed the reader was packed but trying a replacement nothing happens. I get a blue light for battery and a blue light (low) for the supply of direct current, but nothing for power or disc. However, when I plugged in an external drive yesterday it starts fine and when I unplugged the laptop continued to work the internal drive. But even once this morning he died and will not start. I read that the BIOS can stop recognizing the drive or maybe that the settings are not being saved when it is off. Could it be the motherboard battery?

  > reading the BIOS can stop recognizing the drive or maybe that the settings are not being saved when it is off

  Enter the Bios (press f2 at startup) and check if it recognizes the hard disk. You can see on the home page or the boot option in the Bios.

• Qosmio G20: constantly from the noise of the left when speaker microphone webcam enabled

  Hello

  Is that what someone has successfully installed the logitech quickcam 5000 on their Qosmio G20? I can only use it with the microphone disabled - enabling it results in constant "noise" of the speaker left (or earphone).
  It would be nice to get this working...

  Thanks in advance,

  Aiden

  Hello

  I found this useful document of Toshiba which describes the very similar problem:
  http://support.toshiba-tro.de/KB0/FAQ6201DW000YR01.htm

  Maybe it helps

• Re: NB200 - making noise and the screen turns white

  Hello

  My laptop makes the high pitched noise and the screen turns white. Please help with this question.

  Thank you

  Hello

  It is especially as this problem with the inverter. She is, die, and made a noise of pitch. Try to connect the external monitor and check if it is displayed.

  Welcome them

• Satellite L650D - LCD noise in the background

  Hello!

  Please tell me there is someone knows solution or tool that will synchronize the LCD?
  I have a noise on my LCD screen which is very irritating, is the strongest on a gray background.
  On a white background (or other light colors) is ok. I can work normally, but sometimes it's tiring just my eyes when I'm working on gray themes or something.

  Looks simular like noise on my screen on PC. I solve that by pressing the button on monitor auto config, but I have no button here :)
  Help, please!

  Hello

  To be honest, I never heard about the noise from the LCD screen.
  Are you sure that this background noise is caused by the LCD and not another part such as mainboard or AC adapter / CC?

  In any case, you must follow the instructions posted by Akuma. Check the display settings and update the BIOS.