No route to host

Similar Questions

• Deploy the debugging token: no route to host

  I'm using Linux, deploying a token of debugging on a BlackBerry Z10.

  The mode of development, the dev what IP posted on the parameters is 169.254.1.1

  I use the following command: blackberry - deploy - installDebugToken debugtoken.bar - device 169.254.1.1 - password

  And I have the following output:

  Error: Unable to connect: no route to host. Check the settings of IP address for the target. Try to ping the target.

  I can't ping the device from the device using a 169.254.x.x network, unfortunately I am using a 192.168.1.x network.

  I have no firewall, no VPN and the unit is plugged in USB.

  169.254 network cannot be changed on the unit.

  I tried to force my Linux network config, so that I have the following text:

  # ifconfig

  eth1 Link encap HWaddr 00:10:18:31:68:60
  INET addr:169.254.1.2 Bcast:169.254.255.255 mask: 255.255.0.0
  ADR inet6: fe80::210:18ff:fe31:6860 / 64 Scope: link
  RUNNING BROADCAST MULTICAST MTU:1500 metric: 1
  Fall of RX packets: 182264 errors: 0:0 overruns: 0 frame: 0
  Dropped packets: 106368 TX errors: 0:0 overruns: 0 carrier: 0
  collisions: 0 txqueuelen:1000
  RX bytes: 190168290 (190.1 MB) TX bytes: 21806096 (21.8 MB)
  Interruption: 18

  But still, I can't ping the device...

  What did I miss?

  It seems that the device is properly connected to your computer, and networking has been correctly configured. However, the messages that you have found, and the lack of support of ping suggests there is still a network problem prevents you from reaching the unit.

  Did you set it to 'Storage and access' mode 'Windows '? "Windows" mode is RNDIS, which works perfectly and 'Mac' mode (and perhaps her detected) are ECM and has some problems with some linux configurations.

  You can reach the exit of "route ip get 169.254.1.1"? For my part, I see

  169.254.1.1 dev usb0 CBC 169.254.1.2
  cache

  Your network (192.168. *) should not affect your debug configuration, unless your network is a 169.254. * network.

• No route to host the torch device (WIFI)

  I'm testing my application Widget loading a remote web page.  I am only on the torch device itself.  It works fine on the simulator of 9800.

  Private LAN

  WIFI

  The address using IP field with item appropriate in the config.xml file

  Using the browser on the device, I can hit my internal site: http://192.168.1.100/index.html.  This works.  However, when I run my application Widget to the device, which points to the same site, I get:

  ERROR

  The requested URL could not be found

  The following error was encountered:

  • Failed to connect to 192.168.1.100

  The system gave:

  (113) no route to host

  Why can I hit the site from the browser, but not from my application, which has this in the config.xml file?

    http://192.168.1.100">                                                http://192.168.1.100/index.html"/>
  

  Boy, all the guys from RIM should play on their rules.  It would have been easy for them.

  In the Widget/WebWorks config file, you can specify which transport to use application and enforcement.

  The default order seems to be:

        MDS    BIS-B    TCP_WIFI    TCP_CELLULAR    WAP2    WAP  
  

  The problem is, the BIS server can't find my private server (nor should it).  I still think it's a bug, it should go to transport after the failure of BIS - B.

  In any case, I changed my order for testing purposes.  (Not sure I recommend for production, but who knows do).  I moved WIFI upward and now I can load my application my private server remotely.

    
      TCP_WIFI
      MDS
      BIS-B
      TCP_CELLULAR
      WAP2
      WAP
    
  

• "No route to host" network problem preventing the installation of RAC

  Oracle Linux: 6.6

  Version Infra grid: 11.2.0.4

  Virtual Box: 4.3.28 (on the Win 7 machine)

  I am installing a RAC 2 nodes in virtual machines created in VirtualBox. But the check cluvfy is a failure for the networks of my Public and private with the error "No route to host" as shown below.

  Ping between two nodes of work with no latency. without password ssh is configured successfully.

  I have a server dedicated DNS (10.194.135.185). nslookups SCAN, Public and VIPs are working properly.

  Search on Google didn't help much. That's why post here

  = The beginning of cluvfy error

  Check: The subnet '10.194.135.0' TCP connectivity

  Source Destination connected?

  ------------------------------  ------------------------------  ----------------

  brcpda178: 10.194.135.178 brcpda178: 10.194.135.178 spent

  brcpda179: 10.194.135.179 brcpda178: 10.194.135.178 spent

  brcpda178: 10.194.135.178 brcpda179: 10.194.135.179 failed

  ERROR:

  GLWB-11850: System call 'connect' failed with the "113" error when running exectask on the node 'brcpda178 '.

  No route to host

  brcpda179: 10.194.135.179 brcpda179: 10.194.135.179 spent

  Result: The TCP connectivity test failed for subnet "10.194.135.0."

  Check: Subnet node connectivity "169.182.16.0."

  Source Destination connected?

  ------------------------------  ------------------------------  ----------------

  brcpda178 [169.182.16.24] brcpda179 [169.182.16.25] Yes

  Result: Connectivity node passed to subnet "169.182.16.0" with one or more nodes brcpda178, brcpda179

  Check: The subnet '169.182.16.0' TCP connectivity

  Source Destination connected?

  ------------------------------  ------------------------------  ----------------

  brcpda178: 169.182.16.24 brcpda178: 169.182.16.24 spent

  brcpda179: 169.182.16.25 brcpda178: 169.182.16.24 spent

  brcpda178: 169.182.16.24 brcpda179: 169.182.16.25 failed

  ERROR:

  GLWB-11850: System call 'connect' failed with the "113" error when running exectask on the node 'brcpda178 '.

  No route to host

  brcpda179: 169.182.16.25 brcpda179: 169.182.16.25 spent

  Result: The TCP connectivity test failed for subnet "169.182.16.0."

  = End of the error

  # This is my network configuration.

  I created 2 virtual adapters to host (Host-only network).

  ipconfig output host (Windows 7)

  Network adapter Ethernet VirtualBox:

  The connection-specific DNS suffix. :

  Link-local IPv6 Address...: fe80::7930:46e8:a531:289% 24

  IPv4 address...: 10.194.135.1.

  ... Subnet mask: 255.255.255.0.

  ... Default gateway. :

  Adapter Ethernet VirtualBox network #2:

  The connection-specific DNS suffix. :

  Link-local IPv6 Address...: fe80::b43f:3255:b3d0:70eb 30%

  IPv4 address...: 169.182.16.1.

  ... Subnet mask: 255.255.255.0.

  ... Default gateway. :

  10.194.135.0 is my Public network-> eth0 in each node

  169.182.16.0 is my private network-> eth1 in each node

  Here is my file/etc/hosts

  [grid@brcpda178 grid] $ cat/etc/hosts

  10.194.135.185 dnsnode185

  # Public IP #.

  10.194.135.178 brcpda178.testenv.com brcpda178

  10.194.135.179 brcpda179.testenv.com brcpda179

  # Private IP #.

  169.182.16.24 brcpda178 - priv.testenv.com brcpda178-priv

  169.182.16.25 brcpda179 - priv.testenv.com brcpda179-priv

  # Virtual IP # 3

  10.194.135.217 brcpda178 - oravip.testenv.com brcpda178-oravip

  10.194.135.218 brcpda179 - oravip.testenv.com brcpda179-oravip

  #127.0.0.1 localhost localhost.localdomain localhost4 localhost4.localdomain4

  #: 1 localhost localhost.localdomain localhost6 localhost6.localdomain6

  Here's the network interfaces configuration files in each RAC node.

  Value of GATEWAY in the file/etc/sysconfig/network-scripts/ifcfg-ethn is set to the IP address of the virtual NIC adapter to the host (win7).

  On Node1, node2 has been cloned. Thus, the UUID of eth0 and eth1 remains the same for both nodes. Hope that this is not a problem because HWADDR (MAC ID) is different between the nodes.

  brcpda178 (Node1)

  eth0

  =====

  # cat/etc/sysconfig/network-scripts/ifcfg-eth0

  DEVICE = eth0

  TYPE = Ethernet

  UUID = 2ca3918d-d038-483d-946a-271751aeb11f

  ONBOOT = yes

  NM_CONTROLLED = yes

  BOOTPROTO = none

  HWADDR = 08:00:27:17:91:24

  IPADDR = 10.194.135.178

  PREFIX = 24

  GATEWAY =10.194.135.1

  DEFROUTE = yes

  IPV4_FAILURE_FATAL = yes

  IPV6INIT = no

  NAME = "eth0 system."

  eth1

  ====

  # cat/etc/sysconfig/network-scripts/ifcfg-eth1

  DEVICE = eth1

  TYPE = Ethernet

  UUID = dc9be031-ee5f-4129-9023-9c45f6a282da

  ONBOOT = yes

  NM_CONTROLLED = yes

  BOOTPROTO = none

  HWADDR = 08:00:27:01:FC:38

  IPADDR = 169.182.16.24

  PREFIX = 24

  GATEWAY =169.182.16.1

  DEFROUTE = yes

  IPV4_FAILURE_FATAL = yes

  IPV6INIT = no

  NAME = 'eth1 system '.

  brcpda179 (Node2)

  eth0

  ====

  # cat/etc/sysconfig/network-scripts/ifcfg-eth0

  DEVICE = eth0

  TYPE = Ethernet

  UUID = 2ca3918d-d038-483d-946a-271751aeb11f

  ONBOOT = yes

  NM_CONTROLLED = yes

  BOOTPROTO = none

  HWADDR = 08:00:27:A9:68:39

  IPADDR = 10.194.135.179

  PREFIX = 24

  GATEWAY = 10.194.135.1

  DEFROUTE = yes

  IPV4_FAILURE_FATAL = yes

  IPV6INIT = no

  NAME = "eth0 system."

  eth1

  ====

  # cat/etc/sysconfig/network-scripts/ifcfg-eth1

  DEVICE = eth1

  TYPE = Ethernet

  UUID = dc9be031-ee5f-4129-9023-9c45f6a282da

  ONBOOT = yes

  NM_CONTROLLED = yes

  BOOTPROTO = none

  HWADDR = 08:00:27:05:A5:45

  IPADDR = 169.182.16.25

  PREFIX = 24

  GATEWAY = 169.182.16.1

  DEFROUTE = yes

  IPV4_FAILURE_FATAL = yes

  IPV6INIT = no

  NAME = 'eth1 system '.

  Hello

  This error is usually done to firewall or selinux - but since you have already disabled, I recommend you just do a restart of your two virtual machines as I have explained these mistakes here http://salmandba.blogspot.sg/2015/04/using-cluster-verification-utility.htm

  I also believe that you have also disabled Firewall (not only stopped) by using the command «chkconfig iptables» off
  My installation guide 12 c RAC excavation on Linux 6 Treaty of all the prerequisites that are almost the same for the 11 g RAC installation, please check if you have met all the requirements.

  http://salmandba.blogspot.SG/2015/05/installing-Oracle-12C-RAC-on-Linux-6.html

  Salman

• Comments operations manager / file manager returns an error "no route to host" when you try to copy comments RHEL to vCO device

  While trying to use the package manager script comments, I discovered to RHEL6 invited, we have a problem copying the file back from the guest to the vCO. Systematically all fail in the 'Copy of the file of comments to the vCO' workflow and in testing, the error is reproducible.

  Specifically, the final stage of this workflow - result = fileManager.downloadFile (vcoPath, ftInfo) - generates the error "no route to host (workflow: copy of the file of comments to the vCO / Scriptable task (item1) #10).

  Anyone know what could be causing this?

  Make sure your vCO has network connection of the ESX host, the virtual machine is running.

  Comments operations connect directly to the ESX host from the client (here: the plugin from vcenter in vCO) after the opening of the procedure on vCenter.

  See you soon,.

  Joerg

• HIS forehead with OHS AJP13 + plugin AD = > no route to host

  Hello!
  
  How does AD plugin works when ITS is driven with OHS AJP13?
  Now I have an error when trying to add Oracle SES ACL-
  "Cannot update the ACL. An exception was thrown by the identity of the plug-in. See the OC4J log for details".
  
  In the paper, I see:
  08/09/04 17:40:19 INFO AJPRequestHandler-HTTPThreadGroup-44 start getIdentityPlugin:
  08/09/04 17:40:19 INFO AJPRequestHandler - HTTPThreadGroup - 44 CachedUserIdentityMgr created
  08/09/04 17:40:19 INFO AJPRequestHandler-HTTPThreadGroup-44
  getIdentityPlugin identityStore:oracle.security.idm.providers.ad.ADIdentityStore@1883161
  
  08/09/04 17:40:22 ERROR AJPRequestHandler-HTTPThreadGroup-44
  javax.naming.PartialResultException [root exception is javax.naming.CommunicationException: mydomain:389]
  [[Root exception is java.net.NoRouteToHostException: no route to host]]
  oracle.security.idm.OperationFailureException oracle.security.idm.providers.stdldap.util.DirectSearchResponse:hasNext:174
  java.lang.Thread:run:534
  
  08/09/04 17:40:22 oracle.search.sdk.common.PluginException: javax.naming.PartialResultException
  [Root exception is javax.naming.CommunicationException: mydomain:389 [root exception is java.net.NoRouteToHostException: no route to host]]
  
  Plugin AD was re-activated and it connects to the ldap successfully, ITS work ldapbind host correctly
  Before activating the SST in front of ITS it work very well.
  
  Thank you.

  You cannot ping the DOMAIN? Not the name of the domain server, but the actual name of the domain?

• Connection problem: no route to host

  Hi all
  
  I have a problem with my BPEL (worms. 10.1.3.4) process.
  I try to call an external web service and I get the following error (can I access the web service simply by using its URL):
  
  exception on JaxRpc invoke: transport HTTP error: javax.xml.soap.SOAPException: java.security.PrivilegedActionException: javax.xml.soap.SOAPException: Message send failed: no route to host
  
  I tried to ping the remote server successfully, so I should be able to connect (no problem of proxy or something like that).
  
  I tried to look in the logs BPEL found in:
  < oracle home >/opmn/newspapers
  System/bpel / < oracle home > /logs
  < oracle home > / bpel/areas/default/logs
  This does not have anything useful either.
  
  I deploy using JDeveloper. I checked settings proxy here - and none are defined.
  
  Does anyone have any ideas as to what can be wrong?
  Help or advice will be appreciated.
  
  Kind regards
  Aagaard

  Well, it could also mean that the server that runs your applicationserver 18111 port is blocked. So I would check with your network managers if this port is open in your applicationserver. They should check the firewall (if you have no control over this yourself).

  Often the situation with a customer is that your development computer is an application server LAN so that your (development, test, acceptance, production) is a data center on an another sub - lan. With another firewall. Development of your PC, you need to access internet-http and perhaps other protocols. But these are generally not allowed on the data center lan. You will have a separate drive from your lan to the data center development. Probably the server has 2 network cards: one for the internal network and one connected to the DMZ. In the DMZ, probably a configuration of proxy/reverseproxy routes requests from outside of your application server and visa versa. If the proxy must also be checked.

  This should normally be the case in a customer-even when it's a development environment. Because you don't want intruders piracy of your systems, even on the development. And although you might not care, the dev - env should reflect your prod-env. So, it must also use a dmz with a proxy/reverseproxy configuration. If it's a Setup program on your laptop or your local home network your configuration might be simpeler. But then again, you might have to deal with different firewalls. If it's all about your laptop (using VMWare for example) I would try when temporarily stop all firewalls.

  You said that you did not have a proxy. What matters to your pc dev as the application server?

• vCloud connector 2.5 - no route to host

  Greetings,

  When the vCenter begins to export the model it fails with 'export OVF failed. No route to the host.

  Connector nodes and servers of connectors are all on the same vlan (stretched between two sites). Everything is 'UP' to vCloud Connector Server, and both nodes have successfully registered their respective vCenter and vCloud Director.

  All nodes of connector and server can ping in all directions and solve that everything involved.

  I tried Google, but did not find everything about this error and vCloud connector.

  Any suggestions would be welcome :-)

  One side is vCloud Director, the other side Server vCenter Server.

  The problem was that on one side esxi hosts have not access to speak directly to the SCR node.

  Thank you entered

• Database connection - error of creation of the admin user Setup. No route to host

  During step 2: configuration of the database connection we select the "internal database".
  After a short delay, we get a message saying "error of creation of the admin user. No route to the host.
  I have been more before DNS records and back and everything seems in good condition.
  Can someone point me in the right direction to solve this error?
  

  This is an SSL certificate error. Have you changed the default self-signed SSL certificates?

• The fields 'Name' and 'Domain' to 'DNS and routing configuration/host Identification' are always in gray

  In VI3, I used to change the settings of the host DNS (host and domain name) to the tab 'DNS and routing' - & gt; "Identification of home." Even more, if the DNS and DHCP are configured correctly in the environment, there is no need to set these values manually - they were discovered automatically. The story is defferent in vSphere 4. I still have the set of fields 'Name' by 'localhost' and 'Domain' field is empty. And I can't change them - they are grey.

  Seems that the host is still able to discover its hostname automatically. I see the proper name in the (left pane of vSphere Client) console tree. But these values are not met the 'DNS and routing' tab and I can't put them manually.

  This is normal and how do I use these fields now?

  Yes, you're right. It's a little strange, but it works this way in vSphere now.

  ---

  VMware vExpert 2009

  http://blog.vadmin.ru

• No route to host 113

  Hello

  It comes to Ramesh. I use Vm Ware Workstation 7, I am invited to maintianing two Redhat Linux OS for my hands-on lab (RHCE) such configuration DNS, Remote Desktop etc. My question is what the best setting for the network connection to a linux server and other is invited? I'm waiting for responses.

  If you do not need to protect virtual machines in the Bridged network would be nice.

  If you need Internet access, but want to isolate virtual computers (for example, if you plan to configure DHCP on one of the virtual machines), then you should choose using a NAT.

• BlackBerry smartphones getting maintenance book, host table routing and 3G works on unlocked bold 9930

  Hello

  I use an unlocked 9930 phone "BOLD" from verizon in India. My carrier is Vodafone. I am able to browse the internet from the phone by using a wi - fi connection. But I'm not able to use the BBM and apps like Gtalk Instant Messaging. I only turned on a vodafine BIS plan. There is no entry in routing table host, service in the phone book. I need help on this on how to get these two. Please excuse me if I m a very basic question. I'm new to BB. I have some confusion about BIS, BES and data plan. How these 3 are linked and wheather only BIS is suficient to connect to internet using the BB browser or it is mandatory to have a data plan with BIS to go he net?

  It would be a great help if anyone can help me with the above queries.

  Thank you

  Hi trackadi

  Welcome to the Forums of the BlackBerry Support

  trackadi wrote:

  I have some confusion about BIS, BES and data plan. How these 3 are linked and wheather only BIS is suficient to connect to internet using the BB browser or it is mandatory to have a data plan with BIS to go he net?

  If it a personal device so if you add the BlackBerry data Plan / BIS on your account will let you BBM, access to the BlackBerry browser, services of personal e-mail and many other data services on Mobile network, a data plan normal allows all the features.

  When BIS is correctly activated by your carrier you will receive these maintenance book and will be able to see the Scriptures on the host Routing Table.

  But the important question is the Indian more carrier are unable or not to add a device to verizon on network and has been reported by many users. Therefore, communicate with your carrier (Vodafone India) to know your problem.

• Unable to connect to the router WUMC710

  I have a WUMC710 wireless bridge connect to a router, Asus RT-AC66U. The problem is that is no longer, it connects. The wifi LED on the front is not illuminated and in the interface web when you try to connect, it said treatment with a progress bar which is 50% and fails. It used to work fine then one day just stopped working. I tried to disable the firewall of the router, change of bandwidth and even try on another router with no luck. Can someone help with my problem? Thank you in advance.

  What wireless modes that you use on the router principal host?
  2.4 Ghz and 5 GHz routers: try Singlemode G or N or mixed G and N on 2.4 Ghz and single mode N or mixed on 5 GHz?
  Width of the channel to Auto 20 / 40 Mhz or try 20 Mhz only.
  Try to set a manual channel to a channel open or unused. 1, 6 or 11. 11 for Singlemode N if the channel is clear. 13 for the regions of the EU. Try the channel 48 or 149 on 5 GHz.
  http://KB.Linksys.com/Linksys/UKP.aspx?VW=1&docid=f2625b15a5d7454b8e7fafbe65d5aa63_4009.XML&PID=80&r...

  What security mode are you using? Privilege 'egi' is WPA-Personal. WPA2 only.

  Temporarily disable WPA security and see if it connects.

  Doest he bridge connect to a 2.4 Ghz radio?

  Factory reset the bridge and set up from scratch...

  The bridge connects to a different router?

  Reset the bridge, reload the file FW, the factory reset and the whole upward from zero...

• Router EA4500 I can't connect into account outside the home

  I Born just this topic http://community.linksys.com/t5/Wireless-Routers/I-can-t-login-into-smart-wifi-router-outside-home/t...

  and check my email for registration - when I click on the page open link says I'm already registered.

  No idea how to solve this problem?

  Ensure that the ISP's modem has not built into the router. This can interfere with remote access to your router main host.

  Can try to disable your account Smart WIFi or see if you can remove the acocunt router then re - add again.

• WRT54G behind another wired router?

  Hello

  I have a wired network in a small office space.  I would like to buy a wireless router and put on the existing network to add a wireless network.

  WRT54G can be used for this. I would have preferred if the new network was separated, but I would also if it's posible to change the settings of the router so that it begins to work as a simple access point instead.

  I can't change the router of the internet service provider, and I don't want to change the settings in the router either.

  Best regards.

  # This is not possible with your WRT. You cannot prevent attempts to connect from the second router LAN in the first router's LAN. All the second router traffic must pass through the first router that makes everything accessible. You would need equipment to enterprise-level which allows you to filter the arbitrary traffic. But the WRT can do. I can't speak to your wired router.

  If it's only on disabling wireless, you can do that in the web interface of the WRT. You can turn off the wireless radio. Then you can keep the connected WRT.

  The alternative would be to get another (third) router that hosts your internet connection. Then you can connect your router wireless and wired to this third-party router effectively separating the wireless LAN and wired the other sharing the same internet connection.