No Web after KB979482 KB890830 KB980195 KB979916 KB980218 KB979559 KB982381

Similar Questions

• Help, please! Cannot access the web after connected to the VPN

  Hello

  I'm a newbie on Cisco products.  I configured a Cisco ASA 5505 with VPN firewall.  However, I can't access the web after I connected to the remote IPSec VPN.  I also cannot connect to the bands using the intellectual property.  But I can connect to the internal servers in the office with no problems.

  Here is my setup, can someone help please?  Thank you very much

  ASA Version 8.2 (5)

  !

  host name asa

  xxxxxxxxx.com domain name

  enable the encrypted password xxxxxxxxxxx

  xxxxxxxxxxx encrypted passwd

  names of

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP address dhcp setroute

  !

  passive FTP mode

  area of zone clock - 8 schedule

  clock summer-time recurring PDT 1 Sun Apr 02:00 last Sun Oct 02:00

  DNS lookup field inside

  DNS server-group DefaultDNS

  Server name 107.204.233.222

  name-server 192.168.1.3

  xxxxxxxxx.com domain name

  inside_nat0_outbound list of allowed ip extended access all 192.168.1.96 255.255.255.240

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  IP local pool sc-192.168.1.100 - 192.168.1.110 mask 255.255.255.0

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 192.168.1.0 255.255.255.0

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  the ssh LOCAL console AAA authentication

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint _SmartCallHome_ServerCA

  Configure CRL

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH 192.168.1.0 255.255.255.0 inside

  SSH timeout 5

  Console timeout 0

  interface ID client DHCP-client to the outside

  dhcpd outside auto_config

  !

  dhcpd address 192.168.1.5 - 192.168.1.36 inside

  dhcpd dns 107.204.233.222 inside the 192.168.1.3 interface

  dhcpd allow inside

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal strategy group xxxxxxxx-sc

  attributes of xxxxxxxx-sc group policy

  value of 107.204.233.222 DNS server 192.168.1.3

  Protocol-tunnel-VPN IPSec

  XXXXXXXXXX.com value by default-field

  xxxxx xxxxxxxxxxx encrypted password username

  Strategy Group-VPN-xxxxxxxx-sc

  remote access to tunnel-group xxxxxxxx-sc type

  attributes global-tunnel-group xxxxxxxx-sc

  address sc-pool pool

  Group Policy - by default-xxxxxxxx-sc

  tunnel-group xxxxxxxx-sc ipsec-attributes

  pre-shared key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  call-home service

  anonymous reporting remote call

  call-home

  contact-email-addr [email protected] / * /

  Profile of CiscoTAC-1

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory

  monthly periodicals to subscribe to alert-group configuration

  daily periodic subscribe to alert-group telemetry

  Cryptochecksum:5c1c99b09fb26fcc36a8bf7206af8e02

  : end

  Hello

  Try adding the following commands

  permit same-security-traffic intra-interface

  NAT (outside) 1 192.168.1.96 255.255.255.240

  Is there are always problems with VPN then I would maybe change VPN pool to anything other than something that comes into conflict with the LAN.

  In this case, these configurations should do the trick

  In order from top to bottom, they would do the following things

  • First remove the pool VPN and VPN configurations
  • Then remove the VPN pool
  • Remake of the VPN Pool with different network
  • Reattach the VPN pool for VPN configurations
  • Configure NAT0 to the new cluster of VPN
  • Remove the old line of the ACL of the configuration of NAT0

  attributes global-tunnel-group xxxxxxxx-sc

  no address-sc-swimming pool

  no ip local pool sc 192.168.1.100 - 192.168.1.110 mask 255.255.255.0

  IP local pool sc-192.168.2.10 - 192.168.2.254 mask 255.255.255.0

  attributes global-tunnel-group xxxxxxxx-sc

  address sc-pool pool

  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0

  no access list inside_nat0_outbound extended permits all ip 192.168.1.96 255.255.255.240

  Of course you also have the NAT configuration for VPN pools new Internet traffic

  NAT (outside) 1 192.168.2.0 255.255.255.0

  Please rate if the information has been useful if this resolved the issue as mark responded.

  -Jouni

• cannot receive emails after update KB890830

  cannot receive emails after update

  Hello

  KB890830 is the Microsoft® Windows® Malicious Software Removal Tool.

  It is normally a part of your monthly updates.

  At the bottom of the Section 'SUMMARY' in this Microsoft link under "How to receive support", there is a contact number for no support of the charge.

  http://support.Microsoft.com/kb/890830

  See you soon.

• Could not load all sites Web after a certain time (blank)

  Hi, I had a very frustrating problem for the last 2 weeks. Here's how it goes mainly:

  -J' turn on my laptop (or wake up from sleep or other)

  -Go on the internet or simply as the computer for awhile

  -After an indeterminate amount of time (up to maybe 30-45 minutes), I can't seem to load any websites.

  Basically, say I want to go on Facebook for an example; I type the URL, the page SEEMS to load a second but then it stops completely and basically what he did was loading a blank page. This happens with ANY Web site (except the site Internet of Arvato for some strange reason, but perhaps because it is on my favorites.)

  Another interesting observation is that when loading Google (since it's my home page, oh, and I'm talking AFTER that it can not load the pages more), throughout the site displays fine except for this image of google relationship with the logo, it appears at all.

  Now this isn't a browser-specific problem, it affects all my browsers (IE and Firefox 3.5, Chrome EVEN) both so I think something must be wrong with the laptop. So, I took some actions:

  -Retrieve the State of plant (4 times!)

  -System deep Scan (with Bitdefender Total Security 2010)

  -General cleaning of PC/disk using Microsoft integrated program and Bitdefender

  -Registry clean using registry Defense 2009

  -Defragmentation using the Auslogics Defrag Disk

  None of the above solves the problem, so I am totally helpless on what do I do . I did a reinstall System 4 times and the problem persists. I really need help on this one, please if someone knows a solution it shout!

  OS: Vista SP2

  Antivirus: Bitdefender Total Security 2010

  Browsers: IE8, Firefox 3.5

  Laptop model: dv2934ca

  In fact, after some research I discovered that it is actually from Bitdefender 2010, so rest easy, your pc is fine. He apparently took place after a major update in early November.

  There is a temporary fix if you want to: when blank pages, open bitdefender and then go to settings and activate the Expert mode. Then go back to settings and uncheck everything under "security settings", do not forget to click on apply.» Then recheck everything BUT Antivirus and apply again.

  Apparently, this would fix it but your pc would become vulnerable . Just keep updated your antivirus, until they release a fix. Since yesterday I have not had problems, maybe a fix has been released?

• The server does not restart the web after installation

  Hi all

  As I said earlier, after the yellow screen saying Download tools to manage this host of: http

  and I try to restart by pressing f12 was asked to provide credentials for 'local host' after I pressed f11 to restart.

  But now it is empty. Help, please

  Thanks in advance

  You should be able to launch a browser and point to the IP address of your ESXi server to download the vSphere client.

  Your startup time is not normal. ESXi hardware runs on. It's in the hardware compatibility list? http://VMware.com/go/HCL

  Forum - VMware communities forums upgrade notice will be upgraded the weekend of December 12. The forum will be in playback mode only the Friday 10 December 18: 00 PST until Sunday December 12 2 AM PST.

• Unable to connect to FDM Web after installation.

  Hi all
  
  I am not able to connect on FDM Web App gives me an error
  
  "Impossible to cast type COM interface ' LoadBalanceMgr.clsLoadBalanceClass' object type 'LoadBalanceMgr._clsLoadBalance'. This operation failed because the QueryInterface call on the COM component for the interface with IID '{D37350A9-23E7-4827-98BF-B64C5596D8DD}' failed due to the following error: error loading type library/DLL. (Exception from HRESULT: 0x80029C4A (TYPE_E_CANTLOADLIBRARY)).
  
  Also when adding Shared Services in the configuration of the authentication provider Hyperion FDM Load Balance I get the error "cannot create ActiveX component."
  
  Any help please
  
  Thank you

  Contol Panel > Add/Remove programs. Choose to uninstall the EPM system and don't check that the components of FDM.

  Restart the server

  Use installtool.cmd to re - install using the option ' install this release > choose components individually.

• My application content will not appear on the web after uploading on FTP

  I posted my project and I put the contents of the folder web deploy on all my ftp.But, it shows the color that I set as the background color of the project, nothing else. If I download a test html file and displays a simple text, it shows no problem. Is there something I should do to see my online application? What I am doing wrong? My project contains videos and images and transitions between pages and States. I tried to change the Main.html in main.html, or unsuccessfully index.html Main.html. I don't really know what I can do.

  Thank you in advance.

  Erika

  Erika-

  One of the first things to check is that all assets have been uploaded correctly, including the same directory structure that produces CF. A good method to debug these types of questions is in the browser itself. Most have some form of inspector tools. Google Web Inspector tools for the browser you use to know how to install or activate.

  These tools will help report errors and missing files. Using this information, you can detect and correct errors.

  Chris

• Unable to connect via wifi Web after that windows update 8.1

  Laptop HP Pavilion 15 pc 15 n032sa-update to windows 8.1 but now unable to connect to Internet with wifi I have to use the yellow cable.

  Hello

  Please try

  (a) go into Device Manager and uninstall the network card (NIC) wireless.

  (b) restart the machine.

  (c) wait 10 mins.

  Or click on the following link and click Search now

  Kind regards.

• Layout of incompatible web after using a model

  So I made a template for my site, created several pages, and I'm having problems. The pages are very similar, apart from the fact that some of them are slightly different horizontal positions. I don't know how this happened or how to fix this problem because they do the same, I used a model.

  The site is http://www.peoplesphysicaltherapy.com

  It's hard to explain but if you click on the navigation bar, you should be able to see what I mean.

  (I know that coding is pathetic, cut me some slack I am just starting )

  Thank you!

  The jump you see is when you move from a short page to a long page (or vice versa) :-)

  Add the following rule to your style or in the head of your documents:

  HTML {overflow - y: scroll ;}

  This will take care of the jump by forcing all pages have a 'gutter' where the vertical scroll bar would be, even if they do not need a vertical scroll bar.

  --

  Nadia

  Adobe® Expert community: Dreamweaver

  Unique templates CSS | Tutorials | SEO articles

  http://www.DreamweaverResources.com

  http://csstemplates.com.au/

  --------------------------------------------------

  http://Twitter.com/nadiap

• How long before the site appears after the launch?

  How long does take to be searchable on the web after launching a new site?

  DNS records come in a few hours?

  DNS propagation should be fast, but may take up to 24 hours at rare times.

  Regarding the indexing of the site in the search, there is no control over this and can take some time. In this case, just wait until the site is indexed.

  Thank you

  Sanjit

• Widgets not working is not on the web - work in Live View mode

  I'm not a programmer, so I have a lot depends a lot on the visual aspect of Dreamweaver. I was changing a site that I put in place a few months ago and when I changed the type of widget in the model and updated it does not work on the web. It's a widget panel tabs and content arises, but all of this on the page without tab. The tabs are there and active on the live view, but not on the web after the download of the site on the server. Help please.

  You have all files uploaded to your remote server js. Some are, some aren't.

  For example, the link below will throw a 404 not found

  http://www.porositystorage.com/Spry-UI-1.7/includes/SpryTabbedPanels2.js

  You must make sure that all files are downloaded.

• Define and save the preferences / default to save for Web?

  I used PE2 forever, even though my Mac OS updated. Now, however, on Snow Leopard, I had to me PE8, and I'm a little lost. In PE2, if I used the same custom setting to save for Web, after awhile, it just kept and that somehow became my default. It was wonderful. Now, in PE8, the JPG quality is always set to 0. I'd like to something that I like (I'm not completely happy with the presets), and which have been raised by default. I thank very you much for all your help.

  Bantymom

  We all want that. Theoretically you can option-click on the help button and it turns into a button store, but unfortunately in practice it is usually just as distracted as if you had clicked. If you're lucky, he might remember an editing session, however.

• Equium A200-1V0 using XP - recent conversion issues.

  * Hi, *.

  * I recently inherited my laptop the girls, he had vista installed on it. I'm not a big fan so decided to install xp. I found a great guide on the forum, see below, (the topic is now locked) *.

  The original guide:

  + How to install XP Home on the following Vista laptop. 05/01/08 +.
  + PSAF5E + Toshiba Equium A200-1V0

  + Introduction
  + Here are the measures taken by us to remove our Toshiba laptop Vista and replace it with XP Home. There may be inconsistencies in our methods and we cannot have all the correct drivers installed, but everything seems to work OK for us. +
  + Our laptop now runs much faster, opens and closes more quickly and is more stable. +

  + This isn't a 5 minute operation. It should not be attempted by anyone with only a knowledge of passage of computers because it is very easy to screw things. The shop you bought your PC against them will load a lot to fix things and they will probably insist reinstall Vista! +
  + Be prepared that this would also probably negate your warranty. +

  + Luckily, I have a 2nd PC under XP, which allows me to access the web. This is very useful because it means that when your Vista machine is "broken" you can always find help and download the driver files. I also used my 2nd PC to create the XP installation updated the CD discussed later. +
  + You must have access to the web via a PC or another to get the necessary drivers. +

  + Method +.
  + First, even if you have Vista on your laptop, download and run a program of interrogation as "Belarc advisor" that lists all the drivers and software installed on your laptop. Print it out for future reference. It will be useful later when searching on the web for all drivers that may require updating. +
  + Now, make sure that you noted on all the necessary settings for your Internet connection. +
  + Also, back up the files that you may have placed on the hard drive you will lose the lot, including emails and the address books and web bookmarks etc. +

  + Unfortunately, the Toshiba disk that comes with this laptop does not appear to have all the required drivers with it. Instead, I think it relies on Vista keeping copy on your hard drive. It's not very bright that when the disk fails, you have lost everything! +
  + This means to go on the web and the search of all the required drivers run the XP successfully. +
  + Some we have found, for example the wireless network adapter, however this was not a problem because once we had installed XP and connected to the Internet through an Ethernet cable to our router, we were able to run 'Update Driver' for each missing item. +
  + Go to "Device Manager" via "Control Panel" then "System" and then "hardware". Then look for any yellow question mark for all the problems. Right-click and run 'Update Driver' for the Hardware Update Wizard and allow the PC to search the web "this time only. +
  + The ones we made in this way were: wireless adapter, Audio adapter. +

  + Unfortunately an original CD of XP SP2 does not contain the required drivers for this laptop. Therefore, when you start the CD it will be, after a few minutes of installation of files, say you have a hardware problem, there is no hard drive. +
  + To remedy this, you will need to download the right drivers Intel ICH8M SATA AHCI Controller. I could not find on the website of Intel, but on the contrary searched on Google for him. and he got to: http://www.alphadownloads.com/downloads/download-hp-intel-sata-ahci-controller-driver-ver--d-3064.html+

  + The other necessary drivers that we found on the web were: +.

  + Intel chipset device software installer +.
  Web page +.
  + http://downloadcenter.intel.com/Detail_Desc.aspx?agr=N&ProductID=816&DwnldID=14528 & strOSs = 45 & OSFullName = Windows * XP Home Edition & lang = eng +.

  + Or if this link does not try this: +.

  + http://support.intel.com/support/chipsets/inf/sb/CS-021273.htm+

  + Select 'Download Intel chipset software installation utility' on the left side, and then select your operating system "XP Home +.
  + Select "INF Update Utility - primarily for Intel 3, 900 chipset series ' +.
  + and download it. +

  + Driver Intel graphics: Mobile Intel (r) 965 Express Chipset +.
  Web page +.
  + http://downloadcenter.intel.com/Detail_Desc.aspx?agr=N&ProductID=2800&DwnldID=1438 8 & strOSs = 45 & OSFullName = Windows * % 20XP % 20Home % 20Edit ion & lang = eng +.

  + Or if this link does not try this: +.
  + http://support.intel.com/support/graphics/intelgm965/+

  + Now, select "software & drivers" on the left side and select your operating system "XP Home +.
  + You will be presented with a list of files. +
  + Select provided? ® Graphics Media Accelerator Driver for Windows * XP (exe) +.
  + and download it. +

  + Marvell Yukon Ethernet Driver +.
  Web page +.
  + http://www.marvell.com/drivers/driverDisplay.do?dId=175+

  + Or if this link does not try this: +.
  + http://www.marvell.com/drivers/search.do?reload=false+
  + On the right side, select ' W2000 / XP/2003/Vista x 86 & x 64 multilingual Installer (32-bit and 64-bit) for Yukon devices +.

  + Create the XP drivers disk +.
  + Add SATA drivers for a copy of your XP install CD using a program such as NLite. +
  + You have enough spare memory hard drive take a copy of your XP (about 700 MB) installation CD. +
  + Launch the program "sp37005.exe" and it will install on your hard drive. Do not install to a floppy disk. +
  + Download "NLite" of: http://www.nliteos.com/download.html+
  + When you run NLite it will probably say that you need to install ".net Framework", if so, quit NLite and go find the program. It is a Microsoft program that you can find by performing a Google search for the corresponding page on the Microsoft Web site. +
  + Now place your drive to install XP in your CD drive, if it autoruns, leave him. +
  + Run Nlite and follow the instructions on the screen. +
  + The program will ask where is your XP disk then it will ask you where you want to save the copy. +
  + On the screen "Task Selection", select "Drivers" and "Bootable ISO". Press "next". +
  + Select "Insert" and then "Folder pilot several" and now go and find your downloaded files of the SATA driver. Now, select 'All' and ' OK. The program will list the available SATA drivers. Select only the two that mention "ICH8M. Now press "next". The display will show the selected drivers. Press 'Next' and then 'Yes' to the prompt and then on "next" when done.
  + You are presented with the "Bootable ISO" screen. +
  + Put it a new inflammable CD in your CD burner, wait for it to be recognized and out any window that might appear to allow you to install files.
  + Now in Nlite, under "Mode", select "Direct Burn" +.
  + Under the 'Label' enter something like "XP for Toshiba Satellite A200" to identify the drive. +
  + Advanced settings to leave alone and now add the other required drivers by clicking on explore and copy them to the root directory to the temporary directory on your hard drive XP. It might be better to create a "Drivers" folder in the root directory to make them easy to find later. +
  + Now, click on the "Burn" button Now follow the remaining instructions to complete. +
  + You have now created an XP installation disc that contains your SATA drivers. +
  + - As you can tell, it of sound altogether, but avoids having to buy a USB floppy drive and it provides a neat solution. +

  + Hasta La Vista! +
  + Now you are ready to start the cleaning process, if you are brave enough to continue... +.

  + First, re-boot your laptop and the all start-up press F12 to change the boot order so that the CD-ROM/DVD-ROM is first. You can also use F2 and then change the Boot order from there. +

  + Now, insert your new XP installation disc in the DVD/CD drive and re-boot the PC, select boot from CD when you are prompted. +

  + The XP CD will now start copying the files and possibly display an options screen.
  + Select this option to install Windows. +
  + And then remove the hard drive C: partition (with Vista on) +.
  + Delete the partition used by Vista also F. +.
  + You will have to follow a lot of warning messages to delete the partitions. +
  + Now follow the instructions to create an NTFS partition on the C drive. +.
  + Now install XP by following the instructions. +

  + Don't worry that the graphics are a bit large as once Windows has finished installing, you can run the graphics driver you copied on the the XP CD to correct this. +

  + Run three driver files: +.
  + win2k_xp14311.exe Intel graphics driver.
  + INFINST_AUTOL.exe Intel chipset software installation utility ' +.
  + Marvell Yukon Ethernet Driver Setup.exe +.

  + Your graphics card must now improve and you should now be able to connect to the web (after the execution of the web Setup Wizard). But do not do this until you have installed your anti-virus software and firewall. +

  + Now go to "Device Manager" by "Control Panel" then "System" and then "hardware". Then look for any yellow question mark for all the problems. Right-click and run 'Update Driver' for the Hardware Update Wizard and allow the PC to search the web "this time only. +

  + If all goes well, everything should work OK now. +

  + Now go and have a drink to celebrate! +

  * After completing the installation, I found that I had no work wlan driver on my laptop. They are here (RTL8187B_WLAN_Adaptor), but with a big yellow question mark. I tried reinstalling them but it made no difference. I don't know why they don't will be will not installed properly.*

  * All went well and seem to work and all the familiar screens were there. I started using it and wanted to transfer some info from the laptop to my office. I copied the files on a disc using Ashampoo Burning Studio 7 and it seems to work, he went through the whole process without a hitch. When he had finished I checked the drive and it was empty he had no files on it at all. I tried several types/brands but the results (or lack of) is the same. The drive reads the discs will not drive write. Any ideas? *

  Thanks for reading this and I would appreciate any help/advice you may have.

  See you soon,.

  Mike

  Hello

  This means that everything is working properly without WLAN connection and burning the discs?

  Well, are you sure that your laptop is equipped with RTL8187B WLAN card? Therefore, you can check the vendor and device ID in Device Manager.
  But for all the portable Toshiba, you can download the driver WLAN here:
  http://APS2.toshiba-tro.de/WLAN/

  In addition, it would be interesting to know which drive you exactly used for the engraving process. I only use high-quality Verbatim and TDK media. I don t use Ashampoo or Nero, I use CD Burner XP because it the freeware tool and I can do anything I want with this program.

  Check it!

• Internet connection lost Sunday night

  Unable to connect to the web, after that storm last night, interruption of the DSL connection, still can not Monday morning

  On Monday, July 9, 2012 13:35:16 + 0000, mary lynnhawkins says:

  Unable to connect to the web, after that storm last night, interruption of the DSL connection, still can not Monday morning

  See the other answer (s) you've got, but you should also know that your
  equipment may be damaged.

  In the future whenever you have a storm nearby, you should
  always turn off and unplug the computer and also turn off the power and
  Unplug the modem from the phone line.

  Ken Blake, Microsoft MVP

• WRT610N not showing BLUE for Gigabit connection?

  I was on the phone with Linksys TS tonight (and hung up) and also the Live Chat and not getting anywhere.

  I have a nine WRT610N router. Everything works fine when connected by cable CAT6 between my PC and the WRT610N. Firmware has been upgraded to the last descendant of site Web after installation. The only problem I see so far is the following:

  Gigabit Intel Pro1000/GT card, cable CAT6 from PC to the router. EasyLink Advisor shows 953Mbps, the LED shows GREEN (10/100) router is not BLUE (GB). I tried 2 ports on the router and 2 separate new cables CAT6. Is there a problem with the firmware of the router the WRT610N, or display BLUE for a gigabit connection?

  Thank you

  Kevin

  It is a known problem with the WRT610N.  Depending on how you look at it, the manual is incorrect, or the firmware is incorrect.

  For the moment, the following applies to the WRT610N:

  Green is 1000 Mbps, Blue 10 / 100 Mbps.