The server does not restart the web after installation

Similar Questions

• Creative cloud does not recognize my membership after installation of El Capitan

  I have a subscription to creative cloud. Given that I have download El Capitan, creative cloud will allow me to connect, download applications under a free trial and recognize my preferences but will not show me to have a subscription. I tried logging in and out.

  I will have no problem on my work computer, but I did not download El Capitan on this machine, just my computer at home with 10.11.1 is having the problem. Help!

  Please see the links below.

  • Creative Cloud applications unexpectedly back in the test mode. CCM, CS6
  • Applications creative Cloud back in test mode after an update until 2015 for CC

  Also, make sure you use the right adobe ID to log in.

  Hope this will help you.

  Kind regards

  Hervé Khare

• Nodemanager does not restart managed server after reboot of the Linux operating system

  Running Linux 2.6.18, Sun JDK 1.6.0_14 and WebLogic 10.3, we have a functioning correctly nodemanager watch a single managed server. If I kill-9, the managed server, the nodemanager immediately triggers a new. If, however, restart us the box, the nodemanager will start cleanly and does not start the managed server. He seems to believe the node should be kept low and indicates its status UNKNOWN.
  
  I saw where is a problem known on Windows boxes, easily worked around by providing the Xrs setting - for the start settings for the managed server. (Section 5 of the config doc General nodemanager.) I do not, however, where there a just as clean solution for Linux.
  
  Things I've tried:
  + When I put the server for DEBUGGING, it shows no sign of a stop signal is received. It is dumping loads of cluster messages, etc., in the newspaper and then suddenly just log ends so he is going to die by kill-9. If the nodemanager works at this time, he might try to restart the managed server and save it somewhere as failed permanently.
  + The nodemanager saves only the INFO level and connects to evidence to decide to leave the node down. (DEBUGGING is an invalid LogLevel, so that's all I have.)
  + A signal to restart sent our AdminServer (on another Linux machine) begins the node managed through the nodemanager. Nothing unusual happens or is connected.
  
  I'm curious to see things:
  + Is it possible to see what state the nodemanager believes the managed server to be?
  + Is there some value in some doc somewhere who could tell that the server does not have to be restarted?
  + Y at - it is not an action of customer NodeManager log? I see nothing in domain.log or AdminServer.log except when the NM is down.
  
  Thank you
  
  Kevin
  
  ListenPort = 5556
  ListenBacklog = 50
  SecureListener = true
  AuthenticationEnabled = true
  NativeVersionEnabled = false
  CrashRecoveryEnabled = true
  JavaHome = / appl/java/jre
  StartScriptEnabled = false
  StopScriptEnabled = false
  StartScriptName = startWebLogic.sh
  StopScriptName =
  LogFile=/appl/bea/wlserver_10.3/common/nodemanager/logs/nodemanager.log
  LogLevel = INFO
  LogLimit = 0
  LogCount = 1

  You can set NativeVersionEnabled to true. We have faced this in windows that was corrected by changing this property. A few notes on this program:

  Faced with this interesting question in Windows 2008 environment. Managed servers were lit by the Manager of knots and it was expected that a reboot of the system after a crash, the node Manager will restore the State of the managed servers in the State it was before the accident. Node Manager is configured to run as a windows service. As a result, he started after server restart. But individual managed servers were not start-up. Interestingly, for managed servers started by the Manager of the nodes there no .lck file in the folder/data / NodeManger.

  To resolve this problem always, set the following properties in the nodemanager.properties on the base of node maager directory.

  CrashRecoveryEnabled = true / * this default is set to false. This must be enabled for an automatic restart after accident at work * /.

  NativeVersionEnabled = true / * this is by default set to true, and it must be configured as such. If disable you this option on platforms for which weblogic provide JNI native libraries (for example in Windows 2008) then this custom create the .lck file and so node Manager cannot restart the server managed after the crash.

  Note: According to the documentation official .lck files are necessary for managers to auto restart weblogic node after system crash

  Official documentation:

  Once the system is restarted, Node Manager checks each managed domain specified in the nodemanager.domains file to determine if there are server instances were not stopped. This is determined by the presence of all the lock files that are created by Node Manager when a WebLogic Server process is created. This lock file contains the process identifier for the WebLogic Server startup script. If the lock file exists, but the process ID is not running, Node Manager will attempt to automatically restart the server.

  If the process is running, Node Manager performs an additional check to access the management running servlet in the process to verify that the process corresponding to the process ID is a WebLogic Server instance.

  Once the system is restarted, Node Manager checks each managed domain specified in the nodemanager.domains file to determine if there are server instances were not stopped. This is determined by the presence of all the lock files that are created by Node Manager when a WebLogic Server process is created. This lock file contains the process identifier for the WebLogic Server startup script. If the lock file exists, but the process ID is not running, Node Manager will attempt to automatically restart the server. If the process is running, Node Manager performs an additional check to access the management running servlet in the process to verify that the process corresponding to the process ID is a WebLogic Server instance.

  */

• Satellite Pro A300-15 t does not restart on the current after BIOS update

  Hello

  There is something wrong with my Satellite Pro A300-15 t. I made an update of the BIOS of toshiba recently with the latest Web site and it installed successfully. But after the installation, I noticed that my laptop does not restart when it is connected to the power adapter. It restarts and works perfectly when its power on the battery.

  After restart or start-up the laptop (on battery), it will be well when the adapter is connected.

  But, when I reboot when the adapter is connected, after his stop, just power light turns on for a second or two and gets off automatically. And not even the laptop starts manually by pressing the power button (LCD is turned off when the power light comes on for 2 seconds) when the adapter remains connected.

  So what I do is to pull the plug on the adapter, then start the computer manually by pressing the power button and reconnect the plug of the adapter to the laptop starts. It works well this way. Rest everything works perfectly.

  And this problem started after the update of the BIOS. Now, I don't know how to remedy the situation I don't know if there was a bug in the last update of the bios.

  Details of the update from: http://gulf.computers.toshiba-europe.com/innovation/download_bios.jsp?service=AE

  30/07/08
  Update the BIOS
  This Bios update adds functionality to your system.
  Satellite Pro A300 Toshiba of 3, 60 - WIN

  So please help me to solve the problem.

  Thank you best regards &,.
  Manjit M.

  Hello

  Try to update the BIOS again
  In addition, access the BIOS settings and set the default parameters. Save it and try again.

  Good bye

• Single-pass does not work for Web sites after the last update of firefox

  Single-pass does not work for Web sites after the last update of firefox. This works in IE and Chrome and it works under windows (when starting the computer), but not with any website in Firefox.

  Firefox 30 spent some less commonly used "Always turned on" plugins "asking to activate. To check and change this to SimplePass, you can use the page modules. Either:

  • CTRL + SHIFT + a
  • "3-bar" menu button (or tools) > Add-ons

  In the left column, click on Plugins. Then on the right, check the control on the right side of the SimplePass.

  You may need to exit Firefox and start it again before it takes effect.

  A little luck?

• The DNS server does not respond when try connect a Web site

  original title: dns server problem

  m using computer dell laptop with windows xp.i usually to plug my my cell phone and use vodaphone since 2 days internet.since I m unable to access all sites Web on laptop.m get a msg105 error (dns server does not)... so I downloaded the public dns server on cell n transferred on laptop and changed my dns to google dns server server... It worked fine for one day and the next day I had the same problem of server dns - no responding.so I repeated al procedure again and then it started workin again... What is the problem with my dns server... do I have to download na dinstall public dns server every time I use my laptop via the cell phone internet. ?... Help, please...

  Thank you

  It should work with the server DNS of Vodaphone.  Set the laptop to get its IP & DNS addresses automatically, then make sure that the DHCP Client service is set to automatic startup.

  John

• Pavilion Media Center does not restart after the full system recovery. get the error code 0 x 4001100200001005

  Pavilion Media Center does not restart after the full system recovery. created recovery disks when purchased new. get the error code 0 x 4001100200001005

  Original title: recovery problem

  Hello

  According to the HP Support Forums, this error may be to do with the hard or for other reasons.

  You never have it replaced with a no HP bought in car?

  Read these threads HP on your error code:

  http://h30434.www3.HP.com/T5/notebook-operating-systems-and-software/recovery-disk-error-0x400110020000-1005/TD-p/22936

  http://h30434.www3.HP.com/T5/desktop-recovery-reply-only/trying-to-recover-an-old-PC-error-code/TD-p/964509

  If the original hard drive, press F11 at startup to start the process of recovery partition HP, did you recovery disks of.

  See you soon...

• After you have installed SP3 (on XP with SP2), the PC does not restart in normal mode, only in safe mode

  After you install SP3, PC does not restart in normal mode, only in safe mode, without giving a clear indication of what is the problem or how to fix it - other than say to check settings in the Panel (not very useful).

  PC is a Compaq Presario desktop with AMD processor, model #: SR1720AN product #: EL540AA-ABG

  I reinstalled the operating system recovery disks, which reformats HD and installed XP with SP2.

  I then installed the SP3 from a flashdrive (361 MB files). Everything went without hiccups, but final restarts, he won't get to normal mode, safe mode only.

  I did it twice.

  Any ideas? Thank you.

  Here are the specifications of your desktop Compaq Presario SR1720AN. According to the specification, this model comes with a processor AMD and Windows XP Home Edition SP2 installed at the factory. According to your description, it seems that the HP recovery discs may have been poorly photographed for an AMD-based computer. Please see this Microsoft article and this HP document about your problem.

  To solve your problem, please reinstall Windows XP SP2 by booting from your HP recovery disks. After Windows XP SP2 is complete restored and that your computer is operational, download the "Windows XP SP3 with AMD CPU upgrade utility." Run this utility, and then restart your computer. Then download the "Windows XP Service Pack 3 Package of Network Installation" for it professionals. You can also try to use the SP3 Installer on your USB. Install the update to Windows XP SP3 and then restart when you are prompted to.

  This solve your problem?

  Please send BRAVO

• To install the server does not, after a Preparig to install the window hung for several minutes

  Hi, I tried to install memeo backup of a product for a moment, I recentley purchased. I know that the software and the product is not damaged, because I am able to install it on other computers. Its my fault see tho, I have the seagate FreeAgent GoFlex 1 TB external hard drive, and I had planned to use it on several computers. sort of, I installed it on my computer windows 7 without probs., but when I was installing on my windows vista computer, I accidentally unplugged the drive when installing memeo instant upward.  Needless to say, I knew this would be a problem. Windows popped up saying that the dashboard Seagate (which is the program that installs Memeo instant backup) have not installed properly, so I clicked on reinstall this program with the recommended settings, and I handed the drive and started the installation again. When I did, the registration page (for the unit I was using) pops up and froze, so I closed its process, then Setup of the Board of Directors of Seagate Dash appeared and I started to install, and when he rose to installation of the snapshot of Memeo back, it opens a "Preparing to install" window of a windows installer and after about 10-15 minutes , another windows installer window comes up saying ' to install the server does not.

  Ive done my time just trying to solve this problem and believe he made an incomplete registry file, it whenever it tries to install it tries to use the incomplete record. If one has found a solution to this, or knows what that means of ' installation server does not ", it would be very appreciated for your advice.    If you want to know my characteristics. they are {windows vista 32-bit home Basic, sp 2, 3 GB of ram, 2.10 ghz processor}

  Hello

  you are in the wrong forum

  It comes to the installation of vista operating system instance

  Why don't contact you the program manufacturer?

  Try the repair and recovery forum

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-system?page=1&tab=all

• Server does not start after the installation of the USB bootable, ESXi

  Hello

  I installed VMware ESXi 5 on a SSD drive using a bootable USB key, but my server does not automatically start since the SSD after installation. I can boot ESXi in the offered by the BIOS boot menu.

  The startup configuration is perhaps incorrect because during the installation of the USB drive is present, but after the installation, it is not?

  Also has anyone seen this problem?

  Kind regards

  Gijsbert

  Updating the BIOS on the DQ77MK at 49, and you should be able to start - UEFI must never be activated.

• After HA failover, can I do the VM does not restart?

  After HA failover, can I do the VM does not restart on the target host?

  You can set the priority "VM Restart" to "Disabled" to exclude a VM restarted on another host.

  André

• R7000 does not restart after hitting the buttons wireless & WPS

  Need help on my r7000. It has been installed and works fine for months but my son hit the WPS Wifi buttons and now it does not restart. I have just the lights power & internet on

  I must say that I am tech challenged & currently without laptop or PC. I think that I installed with a laptop computer and wonder if I need a connection difficult to solve this problem. I have just an iPad & iPhone right now.

  I thought that to reset the router through genius, but it won't let me connect. I was connected to the router with iPhone & I tried iPad too but same result.

  Do I have to restore the settings to factory & b If Yes, can I install without connection to a PC? I have Comcast modem & wifi.

  All hep much appreciated.

  I had to do a hard reset but it worked. Thank you for your advice

  Problem resolved

• Four-core 64-bit VISTA system does not restart after the latest updates

  My system does not at all now after SP2. It won't even load of recovery disks cannot get sytem to work repairing or family name known good config, etc..

  If you need a copy of the DVD, go to this link and download the image.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/
  Kind regards

  Today, it was a good day, I didn't have to use my AK.

• Windows live mail send error "the server does not support an SSL connection. Server error 250.

  Original title: Windows live mail error send

  Cannot send mail to Windows Live Mail.  Error message... The server does not support an SSL connection. Server error 250. Server - * address email is removed from the privacy *. Windows Live Mail error ID - 0x800CCC7D. SMTP Protocol.  Port 25.

  It's better, thank you. This message is not from the BT Server; It comes from your Avast antivirus which is intercepting your mail. You would be well advised to turn off the Avast Mail shield; It does not add any additional security if you don't by attention elsewhere, and can cause problems.

  I see that it is the record of mail in bulk that because of the problems in this case. Connect to the Web e-mail account and clear the items junk and deleted records.

  BT is recommended to use SSL, but your original question indicated that SSL was not taken in charge for SMTP on port 25. I think we'd better go on all your settings. Recommendations of BT are on this page: BT email: what are the settings for outgoing and incoming mail servers?, but they only work if you disable Avast scanning mail.

  Right-click on the account name in the folders pane, and then select Properties.

  • Under the servers tab, make sure that my server requires authentication is selected.
    Select connect with authentication in clear text.
  • On the Advanced tab, select this server requires a secure connection (SSL) for both servers.
    Make sure that the incoming (IMAP) port is 993 and port for outgoing (SMTP) is 465.

  When you've made all these changes, close Windows Live mail and wait five minutes for the program do its cleaning and save the modified settings. Then, restart the computer and make sure that the Mail of Avast shield is always off.

  Launch Windows Live Mail, then dial a new test message and send it to yourself. Post a new message in your response.

• This morning update of Firefox has been downloaded but does not restart the laptop. He's trying to start and the lights on the keyboard. He continually tries to restart. The screen is blank. It was working fine until I clicked on restart.

  PC IS A COMPAQ PRESARIO V6000 RUNNING WINDOWS XP

  PC DOES NOT RESTART AFTER THE LAST FIREFOX DOWNLOAD THIS MORNING

  The PC screen does not light and I think he's dead. It can be quite fortuitous, and there may be a hardware failure that he would have stopped working even without the download of firefox. I'll have to consider Repair shop and see if anything can be saved on the hard disk.

  Thanks anyway

  Dave