noobie: configuration of the video input of the project?

Similar Questions

• No message signal to s-video input on the screen - how to remove it?

  I pressed a button on my monitor by mistake, and now I have a blue box with the message "no s-video input signal" on the screen at all times.  It's annoying because it's in the upper right corner, covering the buttons I use to close, reduce and optimize windows.

  I tried right click but nothing happens.  How can I get rid of this error message?

  Hi AnneHotmail,

  1 What is the message appear after you restart the computer?

  2 are you able to show display on monitor other than the blue message box?

  3 is this a laptop or desktop?

  I suggest that you restart the computer and check if it works.

  If restarting does not solve the problem, then check and ensure that the monitor is connected correctly to the computer.

  Also try the method below and check if it works.

  (a) turning the computer off.

  (b) disconnect all cables from their bottom or the sides of the monitor (particularly the power cord). Unplug the power supply cord releases all their reset circuit locks

  (c) press and hold the power monitor for 5 seconds button

  (d) plug the monitor power cord

  (e) turn on your computer and check if it helps.

  If the previous step fails, then you will need to consult the manual of the monitor to restore its default settings or contact the supplier of the monitor.

• No video input for monitor and powerless keyboard - computer has the power

  My computer of girls, with the XP system, has the power (power light flashing & the fan) but the monitor receives no video entry and keyboard is dead.  I tried another monitor, but still no video input.  Suggestions for remedy to appreciate.  Thank you, Pat J

  You are more than welcome to help.

  I don't want to throw another curve ball, but I was working on a computer the other day who had the same symptoms as your daughter. The computer would turn on but nothing on the screen. I replaced the graphics card and still no dice. I don't know what made me do but I removed one of the sticks of ram and bam! The graphics was back. This isn't the way that computers are supposed to work. Either the graphics or the ram of the computer must issue codes beep on startup when a component fails. Beep codes each model represents a different problem. I guess what I mean here is you can try to remove one of the sticks of ram and then start the computer. Repeat for each stick. If you intend to go inside a computer, unplug the power cord to the computer before opening the case to work inside. With his unplugged cable press and hold the button for 10 seconds. Make sure that you do not work in an area with carpet covered floor. Repeat these steps each time that you turn off to check a different key. If the icons still do not appear, you are left to try a new graphics card. The one I linked to is a decent card at a fair price. However, if check you with you parts used computer repair shop (not these geeks of department store) you can find out who sells. Tiny most computer stores sell these items and they are generally tested before being put on sale.

• HT-TC 260 Sound does not work via the video inputs

  I recently bought a bar of its HT-CT260.  If I plug the cable box bar using the optical connection, then it works fine.  If I plug the optical connection between the TV and my PS3, then it works fine.  But I get no sound, if I plug the bar directly to the optical input on my Sony KDL-40xbr2.

  Oddly enough, the bar works (TV at the bar) if the TV is on channel antanna, but not if I use the video inputs for my box of cable and the PS3.

  Spend 3 hours with Sony (useless) online support and assistance phone sony (well, but not solves is not the problem).

  The optical plug is designed to produce sounds when the content you watch contains audio digital. (PCM or Dolby Digital® technology) This feature is available on a selection of digital and video streaming shows and is not compatible with the standard of cable stations or analogue.

  The KDL-40XBR2 TV can only output sound via the connection perspective If the TV is using its own tuner (i.e. If the TV is connected to an antenna or direct cable line in the wall) which explains why you do not get sound when using the video inputs because cable box and PS3 use external tuners to your TV.

  If my post answered your question, please click "accept as a Solution.
  This will help other users to easily find their answers when you browse the site of the community of Sony.

• Switching the video inputs

  Hello. I have a Sony KV2585SA TV with 2 RCA video inputs. On one I have connected a DVD player and the other has connected TV satellite. Using the remote control (RM687c) how to move from one entry to another? Thank you.

  Check for no TV/VIDEO button on the remote control to change the entries. You can go through the link below and try to change the video inputs.

  http://www.KB.Sony.com/selfservice/documentLink.do?externalId=C158311

  If my post answered your question, please mark it as an "accepted Solution".

• All your existing data transfers for win8 win7? The same thing happens to the settings and configuration of the printer?

  Original title: fact of data transfers

  All your existing data transfer of win7 for win8 and do o all your settings and printer configurations do the same thing

  The upgrade to Windows 7 or later will preserve my personal files, applications, and settings?

  Yes, the upgrade to Windows 7 or a later version will preserve your personal files (documents, music, pictures, videos, downloads, Favorites, contacts, etc., applications (IE.) Microsoft Office, Adobe applications etc), games and settings (ie. passwords, dictionary, the application settings).

  My programs, equipment and existing drivers will work on Windows 8?

  Most of the applications and designed for Windows 7, hardware drivers or later should work with Windows 8. Of course, with significant changes expected in Windows 8, it is preferable to that contact the software developer and supplier of equipment for the support for Windows 8. Windows 8setup will be keep, update, replace, and may require that you install new drivers via Windows Update or the manufacturer's Web site.

  Backing up your computer:
  When you make significant changes to your computer for example updated operating system, you must always back up. See the links to resources on the backup by clicking the link for each version of Windows you are using: Windows XP, Windows Vista, Windows 7.

  Also check:

  How to back up and restore your files manually

  To learn more.

  The upgrade from Windows 7 to Windows 8

  Please note that if you migrate to and not 8.0 Windows 8.1, you must perform a custom installation.

• Error: Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19).

  Original title:

  Windows 7 no sound at all

  Hello

  I would like to ask help for Win 7 problem 'No audio '.

  I have a Win 7 64-bit Professional desktop PC. It has a motherboard Asus P5Q - EM.
  Previously, everything worked very well over a year, but now there is no sound at all. I see a little red x in addition to the speacer icon.

  I got a craphics card problem and it has been replaced, and shortly after, I didn't notice that no audio problem.

  First of all, I tried to fix the external audio card drivers - no help. Then I thought to use the motherboard
  audio only and removed the external audio card. I have cheked Bios that there is audio compatible motherboard.
  Windows Manager device shows Audio Realtek High Definetion. (Once I reinstalled externally
  audio card, but did not get it to work and I deleted again and focused on getting the Audio motherboard
  work.)

  Through the Device Manager, I uninstalled the device Audio from Realtek motherboard and all other audio related devices and start the PC.
  After you start Windows 7 detects audio devices well and tries to install the drivers but still said the driver installation failed.

  I also used the troubleshooter in Windows 7. According to the material and audio, I clicked on the audio playback troubleshooting. The system has tried to install the drivers, but all have failed in similar way as after rebootig.

  When I go to see the Audio the Realtek High Defenetion properties, it says:
  Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)

  I downloaded the latest drivers (some 54 Mb file called: 64bit_Vista_Win7_R267) Realtek www-site and run it, but no help. Same problem - no sound at all.

  If I run application system information and go to the "components" > "Problem Devices", it is said Realtek High Definition Audio, error code: failure using the VxD loader. It is also noted on the VAN Miniport (IKEv2), error code: this device does not work properly because Windows cannot load the drivers required for this device.

  I also unplug the beam of the motherboard front audio jack. I thought it may create a connector related issues, but he did not make a difference.

  If I ask the system to update the driver using Device Manager, it says that the piloted is up-to-date.

  I checked the details Realteck Sound Device in the Device Manager and it says under the number "Problem code" 13.

  Also other devices under device 'Video controls and sound game' managers do not work. I uninstalled all the. After reboot Windows 7 detects all the. Win 7 tries to install the drivers, but always fails and yellow! singing appears next to all devices.

  Under the NIC in Device Manager there is another device with the yellow! sign as well. The WAN Miniport (IKE v2). I don't know if it has something to do with this audio problem? Win 7 detects it as well after uninstalling and tries to install drivers after the start, but is also always fails.

  Now, I'm confused and I don't know if the problem is really in the Windows registry database? What is error code 13 of Realtek Audio device and what is actually the VxD loader problem?

  I'm completely lost on how to proceed with this problem.

  Can someone give advice on how to continue with this question...

  Tomppa

  I plugged the the hardware id in the Microsoft Update Catalog and the device is identified as a C-Media CMI8738/C3DX PCI Audio Device but there only Windows 2000/XP drivers available through Windows Update (you need to install the ActiveX control to view and download the drivers):

  http://catalog.update.Microsoft.com/v7/site/search.aspx?q=PCI%5CVEN_13F6%26DEV_0111%26SUBSYS_011113F6%26REV_10

  Connect the hardware id PCIDatabase provides a link to C-Media (one-third to the bottom - device ID 0 x 0111):

  http://www.PCIDatabase.com/vendor_details.php?id=376

  However there are a of the drivers mentioned in the following link that can run, and I suggest to try:

  http://www.SevenForums.com/sound-audio/9824-c-media-Freezy-my-PC.html

  The driver is the "Striker 7.1 pilot" (striker81742.zip) in the following link:

  http://www.htomega.com/downloads.html

  An in these drivers .inf file has an id of material corresponding to your device.

  I recommend the creation of a System Restore Point before trying new drivers.

• Need help with the configuration of the Site with crossed on Cisco ASA5510 8.2 IPSec VPN Client (1)

  Need urgent help in the configuration of the Client VPN IPSec Site with crossed on Cisco ASA5510 - 8.2 (1).

  Here is the presentation:

  

  There are two leased lines for Internet access - a route 1.1.1.1 and 2.2.2.2, the latter being the default Standard, old East for backup.

  I was able to configure the Client VPN IPSec Site

  (1) with access to the outside so that the internal network (172.16.0.0/24) behind the asa

  (2) with Split tunnel with simultaneous assess internal LAN and Internet on the outside.

  But I was not able to make the tradiotional model Hairpinng to work in this scenario.

  I followed every possible suggestions made on this subject in many topics of Discussion but still no luck. Can someone help me here please?

  Here is the race-Conf with Normal Client to Site IPSec VPN configured with no access boarding:

  LIMITATION: Cannot boot into any other image ios for unavoidable reasons, must use 8.2 (1)

  race-conf - Site VPN Customer normal work without internet access/split tunnel

  : ASA Version 8.2 (1) ! ciscoasa hostname domain cisco.campus.com enable the encrypted password xxxxxxxxxxxxxx XXXXXXXXXXXXXX encrypted passwd names of ! interface GigabitEthernet0/0 nameif outside internet1 security-level 0 IP 1.1.1.1 255.255.255.240 ! interface GigabitEthernet0/1 nameif outside internet2 security-level 0 IP address 2.2.2.2 255.255.255.224 ! interface GigabitEthernet0/2 nameif dmz interface security-level 0 IP 10.0.1.1 255.255.255.0 ! interface GigabitEthernet0/3 nameif campus-lan security-level 0 IP 172.16.0.1 255.255.0.0 ! interface Management0/0 nameif CSC-MGMT security-level 100 the IP 10.0.0.4 address 255.255.255.0 ! boot system Disk0: / asa821 - k8.bin boot system Disk0: / asa843 - k8.bin passive FTP mode DNS server-group DefaultDNS domain cisco.campus.com permit same-security-traffic inter-interface permit same-security-traffic intra-interface object-group network cmps-lan the object-group CSC - ip network object-group network www-Interior object-group network www-outside object-group service tcp-80 object-group service udp-53 object-group service https object-group service pop3 object-group service smtp object-group service tcp80 object-group service http-s object-group service pop3-110 object-group service smtp25 object-group service udp53 object-group service ssh object-group service tcp-port port udp-object-group service object-group service ftp object-group service ftp - data object-group network csc1-ip object-group service all-tcp-udp access list INTERNET1-IN extended permit ip host 1.2.2.2 2.2.2.3 access-list extended SCC-OUT permit ip host 10.0.0.5 everything list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq www list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any https eq list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq ssh list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 no matter what eq ftp list of access CAMPUS-LAN extended permitted udp 172.16.0.0 255.255.0.0 no matter what eq field list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq smtp list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq pop3 access CAMPUS-wide LAN ip allowed list a whole access-list CSC - acl note scan web and mail traffic access-list CSC - acl extended permit tcp any any eq smtp access-list CSC - acl extended permit tcp any any eq pop3 access-list CSC - acl note scan web and mail traffic access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq 993 access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq imap4 access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq 465

  access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq www

  access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq https

  access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq smtp

  access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq pop3

  access-list extended INTERNET2-IN permit ip any host 1.1.1.2

  access-list sheep extended ip 172.16.0.0 allow 255.255.0.0 172.16.0.0 255.255.0.0

  access list DNS-inspect extended permit tcp any any eq field

  access list DNS-inspect extended permit udp any any eq field

  access-list extended capin permit ip host 172.16.1.234 all

  access-list extended capin permit ip host 172.16.1.52 all

  access-list extended capin permit ip any host 172.16.1.52

  Capin list extended access permit ip host 172.16.0.82 172.16.0.61

  Capin list extended access permit ip host 172.16.0.61 172.16.0.82

  access-list extended capout permit ip host 2.2.2.2 everything

  access-list extended capout permit ip any host 2.2.2.2

  Access campus-lan_nat0_outbound extended ip 172.16.0.0 list allow 255.255.0.0 192.168.150.0 255.255.255.0

  pager lines 24

  Enable logging

  debug logging in buffered memory

  asdm of logging of information

  Internet1-outside of MTU 1500

  Internet2-outside of MTU 1500

  interface-dmz MTU 1500

  Campus-lan of MTU 1500

  MTU 1500 CSC-MGMT

  IP local pool 192.168.150.2 - 192.168.150.250 mask 255.255.255.0 vpnpool1

  IP check path reverse interface internet2-outside

  IP check path reverse interface interface-dmz

  IP check path opposite campus-lan interface

  IP check path reverse interface CSC-MGMT

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 621.bin

  don't allow no asdm history

  ARP timeout 14400

  interface of global (internet1-outside) 1

  interface of global (internet2-outside) 1

  NAT (campus-lan) 0-campus-lan_nat0_outbound access list

  NAT (campus-lan) 1 0.0.0.0 0.0.0.0

  NAT (CSC-MGMT) 1 10.0.0.5 255.255.255.255

  static (CSC-MGMT, internet2-outside) 2.2.2.3 10.0.0.5 netmask 255.255.255.255

  Access-group INTERNET2-IN interface internet1-outside

  group-access INTERNET1-IN interface internet2-outside

  group-access CAMPUS-LAN in campus-lan interface

  CSC-OUT access-group in SCC-MGMT interface

  Internet2-outside route 0.0.0.0 0.0.0.0 2.2.2.5 1

  Route internet1-outside 0.0.0.0 0.0.0.0 1.1.1.5 2

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  the ssh LOCAL console AAA authentication

  AAA authentication enable LOCAL console

  Enable http server

  http 10.0.0.2 255.255.255.255 CSC-MGMT

  http 10.0.0.8 255.255.255.255 CSC-MGMT

  HTTP 1.2.2.2 255.255.255.255 internet2-outside

  HTTP 1.2.2.2 255.255.255.255 internet1-outside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs set group5

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  Crypto map internet2-outside_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  crypto internet2-outside_map outside internet2 network interface card

  Crypto ca trustpoint _SmartCallHome_ServerCA

  Configure CRL

  Crypto ca certificate chain _SmartCallHome_ServerCA

  certificate ca xyzxyzxyzyxzxyzxyzxyzxxyzyxzyxzy

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as

  quit smoking

  ISAKMP crypto enable internet2-outside

  crypto ISAKMP policy 10

  preshared authentication

  aes encryption

  md5 hash

  Group 2

  life 86400

  Telnet 10.0.0.2 255.255.255.255 CSC-MGMT

  Telnet 10.0.0.8 255.255.255.255 CSC-MGMT

  Telnet timeout 5

  SSH 1.2.3.3 255.255.255.240 internet1-outside

  SSH 1.2.2.2 255.255.255.255 internet1-outside

  SSH 1.2.2.2 255.255.255.255 internet2-outside

  SSH timeout 5

  Console timeout 0

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal VPN_TG_1 group policy

  VPN_TG_1 group policy attributes

  Protocol-tunnel-VPN IPSec

  username ssochelpdesk encrypted password privilege 15 xxxxxxxxxxxxxx

  privilege of encrypted password username administrator 15 xxxxxxxxxxxxxx

  username vpnuser1 encrypted password privilege 0 xxxxxxxxxxxxxx

  username vpnuser1 attributes

  VPN-group-policy VPN_TG_1

  type tunnel-group VPN_TG_1 remote access

  attributes global-tunnel-group VPN_TG_1

  address vpnpool1 pool

  Group Policy - by default-VPN_TG_1

  IPSec-attributes tunnel-group VPN_TG_1

  pre-shared-key *.

  !

  class-map cmap-DNS

  matches the access list DNS-inspect

  CCS-class class-map

  corresponds to the CSC - acl access list

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map global_policy

  CCS category

  CSC help

  cmap-DNS class

  inspect the preset_dns_map dns

  !

  global service-policy global_policy

  context of prompt hostname

  Cryptochecksum: y0y0y0y0y0y0y0y0y0y0y0y0y0y

  : end

  Adding dynamic NAT for 192.168.150.0/24 on the external interface works, or works the sysopt connection permit VPN

  Please tell what to do here, to pin all of the traffic Internet from VPN Clients.

  That is, that I need clients connected via VPN tunnel, when connected to the internet, should have their addresses IP NAT'ted against the address of outside internet2 network 2.2.2.2 interface, as it happens for the customers of Campus (172.16.0.0/16)

  I am well aware of all involved in here, so please be elaborative in your answers. Please let me know if you need more information about this configuration to respond to my request.

  Thank you & best regards

  MAXS

  
  

  Hello

  If possible, I'd like to see that a TCP connection attempt (e.g. http://www.google.com) in the ASDM logging of the VPN Client when you set up the dynamic NAT for the VPN Pool also.

  I'll try also the command "packet - trace" on the SAA, while the VPN Client is connected to the ASA.

  The command format is

  packet-tracer intput tcp

  That should tell what the SAA for this kind of package entering its "input" interface

  Still can not see something wrong with the configuration (other than the statement of "nat" missing Dynamics PAT)

  -Jouni

• Configuration of the audio channels in PP 2015.3 v10

  Hello

  I noticed that the path of the Audio track has changed to the Configuration of the Audio channels in the settings of export of the latest PP. Unfortunately, this affects the way in which players such as QuickTime read the layout of the audio channel.

  For example, I went out a DNxHD MOV video with 24 channels for a customer. I attributed to them in my PP of the project and am ready to the output file. The previous version of PP has allowed you to assign titles in the drop-down menu, the Audio track route which, in turn, allowed to see each audio channel / stem in the movie in QuickTime player Properties menu option.

  Unfortunately, in the last version of 2015.3, my final file of DNxHD output has all channels play off the one audio track when opens in QuickTime player. However, I don't see all the audio stems when I reimport the DNxHD PP file so I think that this only affects the software outside Adobe.

  I wouldn't mind not so much, but the customer would like to see the audio presentation in QuickTime player, so I'm a little confused as to what is wrong here with the last update PP.

  Why this changed in the first place? Any help will be very appreciated!

  Concerning

  Tony

  System specifications:

  Premiere Pro 2015.3

  Windows PC 10, 16 GB of RAM

  So, I thought about it fortunately! So you have to choose Audio MONO Channel Configuration settings and then add as many channels as you need (for me it would be 24 mono tracks). As long as you properly assigned audio channels of your sequence, then the output file should be fine.

  This seems a strange and unnecessary change for me - I don't know Adobe not have their reasons, but that would have saved me some valuable time if we have correctly explained in the update notes!

• Thunderbird 38.3.0: No writable calendars are configured for the invitations with the provider for Google Calendar 1.0.4

  Hello

  I searched many hours today in the internet and your forums, but it seems that this problem is not solved yet:

  No writable calendars are configured for the invitations with the provider for Google Calendar.

  My Thunderbird is 38.3.0 and the provider for Google Calendar 1.0.4.

  I put calendar.google.enableEmailInvitations; true but it did not help. I also tried [email protected]... @googlemail.com. Calendar works fine, it syncs, I see all the entries etc. But I can't accept invitations even IF she must have write access.

  What can I do? Is there a solution for this?

  Thank you!
  Daniel

  Use CalDAV here to access Google Calendar via lightning. I have no experience with the add-on of the provider.
  In any case, it is my understanding that you must assign an e-mail address to a calendar in order to be able to accept the invitations for this calendar. I see that in your screenshot.
  You can try to remove the Google calendar in lightning and re-create it. Given that all the data is on the server nothing will get lost.
  Or you may want to try CalDAV.
  https://blog.Mozilla.org/calendar/2013/09/Google-is-changing-the-location-URL-of-their-CalDAV-calendars/

• Several Airport Apple ID devices disappear shared devices and Software Configuration of the airport

  We have three Airport extreme and two Airport Express devices in two offices in the city.  Some time in the last two days, they all stopped appearing in the sidebar of Finder 'Shared' category (if they had attached disk storage) and they stopped from appearing in the Configuration software of the airport on any of the Mac on these networks. (They always seem to be correct, routing traffic, however).

  For a while, we left a desktop completely alone as a control group and did all our testing and troubleshooting in the other office.

  We-hard reset (to the factory configuration) all devices from the airport to an office. They began to appear again. Then we started to re - configure them again.  At the time wherever we had updated the devices they had disappeared again.

  So, another factory discount based configutations for each device to this facility. Then we added slowly in pieces of their configuration.  When airports have received Apple ID and associated passwords for associating with iCloud/BackToMyMac/WideAreaBonjour (depending on what you want to call it), the airport devices disappeared from the airport Setup.

  If we tried to configure another device from the airport to extend a network of 'invisible' airports, the new airports were "unable to find" one of these networks to expand.

  If we reset all devices without providing them with Apple ID and passwords, they worked mainly as you would expect. The main difference being now do not appear as having been recorded as BackToMyMac/WideAreaBonjour devices.

  One side for people dealing with this note: If your router are invisible, but they are configured to be configured from the EXTENSIVE worldwide network, you can use "File-> configure the other" and specify the address WAN of the missing aircraft and get this screen access as one would generally. From here, remove all the Apple ID associated with these devices, press "Refresh" to save the settings and they seem to reappear magically in the Configuration of the airport software.

  In that State, storage seems to be available, but only for devices in Domain Local (direct connection). Airports without AppleIDs will not appear in the field to iCloud/BackToMyMac/WideAreaBonjour, and it's as expected, given that these IDS is the means for the identification of their field.

  If someone else has noted these behaviors and if so, have an idea about specifically when they first appeared? Is there by any chance someone who knows of any change in registration or the MWAC of multiplication?

  Did you approach the problem exactly as I did in the past, and having encountered problems of the CCMM literally every version of OS X. They were all distinct problems with individual characteristics, and in some cases the solutions exist. Having said that the CCMM has been completely reliable recently - which means running the most recent El Capitan release on all my Macs. The initial versions (i.e. OS X 10.11 to 10.11.3 maybe) didn't work at all. I don't know which version fixed whatever the problem was, I am sure he has not worked for someone else.

  The same real place with Yosemite and previous versions as well. CCMM did not reliable until the exit "point three or four."

  Through these experiments, I believe it should be a pretty fast connection. If the connection between a Mac and all the others does not meet this requirement (whatever that is) all you will be able to determine, it's that the CCMM fails.

  Apple is characteristically silent about the technical aspects of the CCMM, probably because of security concerns. Nobody outside Apple knows how it works. If you're still having problems, I encourage you to contact them. After mentioning predictable you corrective raw materials (the two following links) you will be put in touch with someone who will look to what is false, providing diagnostic assistance and send your information to engineering. If it's something they should fix, you'll know not to the point of an OS X update is published.

  Set up and use Back to My Mac - Apple Support

  Get help using Back to My Mac - Apple Support

  With all the conversations I had with Apple on this topic (which were many, involving a large amount of tests) not once they disclose any causal factors individual, other than to reiterate the need to run the last OS X, versions and the latest versions of firmware for their routers. In your case, that means probably that your Mac update to El Capitan. It is after all the very first recommendation in their document of support above, until you do this you will still not get in step 1.

• How I can do it then when I delete a project, it will remove videos associated with the project.

  Hello

  I recenty used my 1 TB of storage on my Macbook Pro, and I was looking for in what has been the cause of this. I realized that about 700 GB because of videos on final cut. Knowing this, I saved all my videos and decided to remove the oldest, but keep the new. I checked my storage, and nothing has changed. I realized, the application was not delete videos, but rather delete just how clips have been published. He always kept the full video. So what I request is, is anyway that I can make sure when I delete a project, it will remove all the (video) content, associated with this project? Also, is there anyway that I could delete the video projects I already deleted?

  MAC NEWS...

  OSX El Capitan

  10.11.5 version

  MacBook Pro (retina, 15 inch, mid-2015)

  2.8 GHz Intel Core i7 proccessor

  16 GB 1600 MHz DDR3 memory

  Start drive Macintosh HD

  Graphics AMD Radeon R9 M370X 2048 MB

  Storage 1 TB of storage Flash

  FCP INFO...

  Version 10.2.3

  All depends on how you store your media, be it inside the library or outside the library. If internal sound then the best way to proceed is to organize your material in events as well as your project. When you delete events associated with the project, media in events are deleted as well.

• Firefox is configured as the default browser, but if I click on a link in MS Word, the link opens with MS Internet Explore. Why?

  Firefox is configured as the default browser, but if I click on a link in MS Word, the link opens with MS Internet Explore. Why?

  I have the same problem, but the difference is in the opening of the MS WORD hyperlinks to download documents (for example http://ntv.spbstu.ru/2011/hss_2011_3.pdf#page=145 ). This link wants to call MS IE.
  At the same time, all the HTML links are opened in FireFox.

• Configuration of the BIOS XW8600 for SSD and HDD

  Until recently, my xw8600 has been configured with the emulation of SATA under storage on the separate IDE controller Options.  250 GB hard drives connected to the SATA 1 and SATA ports 0 and readers of DVD RW Drive connected to 2 SATA and SATA 3 ports.

  I wanted to install a GTX240 Neutron Corsair SSD, but discovered when I changed the SATA RAID + DCIS emulation (to activate all 5 ports of SATA controller and optimize the performance of the SSD), the system could not find the boot drive.  I checked the startup command settings and found the slot drive HARD listed title module of memory into the attached USB printer HP Officejet 7500 a first and could not be changed.

  I decided to go back to SATA IDE emulation separate, remove the optical drive on SATA 2 port and attach the SSD it.  This facility is expected to start successfully; but after installing windows 7 x 64 on the SSD (Windows XP, x 64, still on the HARD drive), I found Windows 7 has been very very slow.

  Can anyone offer any suggestions or comments on how I can improve this situation?

  Thanks for any help, you can suggest.

  What is an installation of Windows 7 Pro 64 - bit of a retail installation DVD purchase, or something HP?  If I remember well Vista 64 was the latest HP OS with sold.  In this case you won't have to deal with a set of HP restore disks.  I would never do an "upgrade" of a prior installation of OS in W7.  I only do not clean install W7 on a freshly long-type reformatted hard drive or an SSD.  I buy my "system builder" OEM license W7Pro 64 - bit DVD/COA from newegg.com (you can find that many sources and approximately 140.00 each).

  Plan to do a clean install on this SSD from scratch and when you format before that settle does long formatting version, while it is booted from the W7 DVD.  That will take some time.  Or, if you have a functioning before the OS install on a hard drive, you can restore the xw8600 you can connect the SSD in the second or third SATA port and reformat (long version) management of records like this.

  The boot drive or SSD, Spinner, must always be connected to the primary SATA port, which in these workstations, is usually blue plastic, while the rest are a dark black.

  Make sure that your BIOS is later... There was a version for this and the xw6600 with a few months ago.  It is an important.

  Put the SSD in your favorite mount, hang it in the main SATA port, prepare the W7 DVD in the DVD drive (which should be attached to the second port SATA or IDE cable if it's a DVD ATA drive). Throwing xw8600, go straight into the BIOS and go to which you can change the SATA emulation.  Change that on "RAID + AHCI.  Save on the way out of the BIOS, and the workstation will now reboot usually requiring formal approval of the change F1.

  Demarrer start on the DVD, select clean install and things will be fine.  I usually set my boot order to start hard drive/SSD first and second optical drive.  Then, when I load an OS I just use the F9 key during the early start to switch to the DVD player for this single event.

  It's the key information: If you have correctly set to "RAID + AHCI" SATA emulation for the W7 installation process, then the appropriate drivers will not be loaded from the DVD on the startup disk, and you won't receive anywhere near your expected speed.  I helped a friend who had done exactly what you did, and when we corrected things literally double SSD performance scores.  I recommend that the reformatting/clean reinstall from zero here, because you want to really perfect the basics and the way he was treated initially can leave you with a few important questions.

  After you have things working with the SSD and the DVD player you can add in your other material sequentially.  I would like to make a reboot between each addition, just be very careful.  Some old HP DVD drives have a problem with W764 loading during the emulation of the SATA BIOS is set correctly and there is a solution for this, but you don't want from now this info.

  All the advice I have written in this forum about the xw6400 installs apply to the xw6600 and xw8600, including information on the upgrades of the processor.

  Let us know how things are, so that others can enjoy...

• What is the configuration of the maximum ram for a 2007 iMac 21,5 "

  What is the configuration of the maximum ram for a 2007 iMac 21,5 "

  There is no such thing as a 2007 21.5-inch iMac; the 2007 iMac is all 20 or 24 inches. Click here and search for your model; the page it will say.

  (141476)