Not present additional results in real estate to TestStand 4.0

Similar Questions

• Condition of additional results work does not correctly for the parameters

  TestStand 2014

  Trying to connect a parameter only if the status of the step is "failure" will not save the setting when the step will actually fail.  On the other hand, variables with the same State will record very well.

  The sequence attached illustrates this.  Basically I have a sous-suite that returns a random number and a string as parameters.  I use the random number to evaluate against my limits for the test call.  I want to save the parameter of string only if the step fails.  So I put as an additional result, then assign the condition

  Step.Result.Status == "failed".

  The data never show on the report.

  But when I put a result additional explicit with the same local variable and put the same exact condition it appears on the report when the step fails.

  I'm puzzled as to why settings will not open a session to this condition, but additional explicit results work fine with the same State.

  Any thoughts?

  Thank you

  Condition for additional result of the parameter is evaluated before the State sequence is set to failure. The 'out' parameter additional results are evaluated probably just after the code module, so if the status of the step is not changed by the call of code module, then it will always be "Running".

  I can see how it would be nice if it worked the way you ask, but keep in mind for input/output parameters it is usually the same expression/variable to both the 'in' and 'out' additional result, so it is important to the time at which the result is recorded. It must be done before calling code module for 'in' settings and after the call of code module to 'out' parameters to reflect the State of the variables to these points in time. I think that the intention is that the additional result for settings must reflect the State of the variables at the point in time immediately right before the call for 'in' settings and immediately after the call to 'out' parameters So if you want to connect under certain conditions a value based on the status (where the State is not changed directly by the code module), with the help of a result extra ordinary as you discovered is probably the best way to go.

  Maybe for the parameters we might delay logging to the end, but which may result in a change of behavior if the variable state changes again once before that. If you want us to consider or have another idea for how to handle this better please let us know or maybe post something to the exchange of ideas.

  Another possibility is that we could temporarily connect the results before and after the code module, but then not assess the condition to the end and throw the recorded result if the condition is false. Who can still cause a change in behavior although if "Value of Log" expressions have side effects.

  Hope this helps clarify things.

  -Doug

• Why additional results stage does not meet the test report

  I have a file of sequence with several subsequences and I can't using step of additional results. I use the step of additional results in a subsequence and the specified results are added to the report test, but when I use the additional results stage on the main sequence, that nothing is added to the test report.

  There that something is off on the main sequence, which prevents additional results to add to the test report? I use the sequential model.

  The problem seems to be that the Locals.ResultList variable has been removed from your sequence. No results can be entered only if this variable exists.

• search for real estate criteria

  I have to add a search for real estate criteria on my site, I do not know how?

  Hello

  There is no output from the box solution to add a search in Muse area. However, if you decide to host your site on Business Catalyst, you can use the feature given in British Colombia search box. In addition, if you want to use more than one search form field, you can use webapps in British Colombia to do. For more information, please see the following links:

  http://helpx.Adobe.com/business-catalyst/partner/Web-apps-module-create-custom.html

  http://KB.worldsecuresystems.com/242/bc_2428.html

  Kind regards

  Aish

• When I click on an image or map that is Kijiji real estate pages, open Firefox all crunched on the right side of the page. How can I fix this?

  When I click on an image or map that is Kijiji real estate pages, open Firefox all crunched on the right side of the page. How can I fix this?
  For example, I discovered an apartment ad that has various attached photos. It said click on the images to see an enlarged version. FF opens the page however the majority of the page is white and the image seems to be pushed on the right side of the page and watch as if it were bundled up against the right side shows is not the whole picture.
  What can I do to fix this?

  Thanks Cor - el,
  Just set the police minimum votes to zero, did the trick. However, I also appreciate other suggestions that I'm following now. Non-strabisme already installed. A little more difficult to find this file user.js. It any suggestions?
  Thanks again for your great help.
  See you soon,.
  Robert

• Why I can not contact you with FEEDBACK REAL

  Why I can not contact you with FEEDBACK REAL? Why Firefox to 28 allows me to download files from Web page complete, but worms 30 does not work? Plugins, Addons, Internet Security are the same on both systems. I can download the files in IE but not Firefox. What gives? I use NoScript, Better Privacy, Ghostery, and Kaspersky Internet Security configured the same on both systems. The only reason I checked is because on some sites, I can't download files and point of view completely. 30 to Firefox will download but not to create a complete directory html link so that I can open and view the file.

  Hi obliviondoll, the feedback site is here:

  https://input.Mozilla.org/feedback

  This is the page that opens if you use the Help menu in Firefox and choose to submit your comments...

  You can provide your e-mail address on the site of feedback where people reviewing the feedback have questions, but I think that it is rare that you would be so don't expect a response.

  In addition, I don't know if you scrolled down beyond the map on the contact page, but there are links down here (see the attached screenshot):

  https://www.Mozilla.org/contact/spaces/

• Logging of additional results of step before reminder

  In my sequence, the recall of SequenceFilePreStep checks if a step is a test step (e.g. NumericLimitTest). If this is the case, a value of temperature of an overall picture must be kept at additional step results. Let's say the array of temperature index is just zero here. I use the following statement then.

  RunState.CallingStep.AdditionalResults.CustomResults.Insert("FileGlobals.Temperature[0]",FileGlobals.Temperature[0],"",PropFlags_IncludeInReport,-1)

  The problem is that the name of the variable is evaluated as a number, which is the same as the value of the temperature. (See the image attached) But it's not even me to use an arbitrary name as "Temp". [He forces me to use the "FileGlobals.Temperature [0 '] under the name of the variable. Otherwise, I get an error. How can I assign a variable name in the additional results I want?

  Is another question, is it possible to check if there is a variable with a name to additional results lag, using expressions? Basically, I want to replace an old value of temperature in complementary with a new value results whenever a loop iterates.

  Any input will be appreciated.

  pomirobotics,

  In fact, the result name is an expression rather than just a string (you can see in the section additional results of stage settings and looking at the Visual editor for additional results entries). Therefore, you must include a different set of quotes in your expression to name. Here is an example:

  RunState.Step.AdditionalResults.CustomResults.Insert("\"ResultName\"","Locals.MyNumber","",PropFlags_IncludeInReport,-1)

  Backslashes are outside the game internal citations so that they are interpreted correctly when the expression is executed.

  I hope that helps!

• Additional results fail step?

  So I get to use the latest versions of TestStand and I play with the additional results for a test step.  What I was asking is; additional results reach the status of success or failure of a step?  For example, if I have a numerical limit step that also returns a Boolean value, can I use an additional result to not respect the condition based on the value of the Boolean value?  Or are, additional results just for reporting?

  Additional results affect the content of the report. If you need one step regarding its outcome depends on two different parameters (for example limit indicator and digital Boolean), you must create a custom step type.

  hope this helps,

  Norbert

• Additional results - vs Value reference Bug

  I just wanted to find it there. When you try to open a session of additional results of a step, you can specify if you want to connect the value [In] or the [Out] all the variables passed by reference. If you have a variable that is passed by value, you can only connect [] that the value does not change. Makes sense.

  However, if you have a variable passed by value and then change to make reference to, it will not refresh to enable a value [Out] until step is reloaded.

  Thank you for reporting this bug. You experience this problem with a sequence step call? If so, there is a bug existing on this issue report. The ID is 142282. This problem should be corrected in a future version of TestStand. For now, you can work around this problem by clicking on the check box 'Use Prototype of Sequence' twice for change and then restore its value. When you do this the parameters in the update of the additional results panel.

• NI LabVIEW driver for the SRS DS345 function generator generates error "(Hex 0xBFFF0011) insufficient location information or the device or resource is not present in the system."

  Hello

  We have a generator function SRS DS345.

  I just downloaded the driver NOR for the instrument on http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=E3B19B3E9149659CE034080020E748....

  After installation, the DS345 appears in MAX, and I can well communicate with him.

  However, if I run the srds345 to Started.vi, I get an error "location information insufficient (Hex 0xBFFF0011) or the device or resource is not present in the system" from initialize it with Options.vi srds345 sub - vi.

  The only change I did Exchange address GPIB 14 to 19, which is our function generator GPIB address. In addition, the

  Functions of SRS DS345 generator of function palette is empty, even after you restart LabVIEW (see attachment). I'm using LabVIEW 8.5.1.

  Your help in resolving this issue is appreciated. Thank you.

  Best regards

  Peter

  Have you installed the driver from LabVIEW or copied directly from inst.lib?

  The first is easier, and you don't have to restart LV more...

  Error in a not filled gpib address points. I have not checked if this driver has a resource name visa or a string of gpib address old but in the first case, try the little triangle on the right at the slect address instead of by hand.

• The drivers for this device are not installed. (Code 28) __This device is not present, is not working properly or is not all its drivers installed. (Code 24)

  I HAV these two errors in my drivers and windows cannot update, can any body healp me?

  Hello

  What devices are - if you can not tell what is the name, then you can specify the category of
  Device Manager - or both?

  --------------------------------------------------------------------------------------------------------------------

  This device is not present, is not working properly or is not all its drivers installed. (Code 24)

  The device doesn't seem to be present. The problem may be a faulty hardware or a new driver might be needed.

  Devices to stay in this State if they have been prepared for removal. After you remove the device, this error disappears.

  On theGeneral properties of the device tab, clicktroubleshoot to start the Troubleshooting Wizard.
  ---------------------------------------------------------------------------------------------------------------------
  The drivers for this device are not installed. (Code 28)

  To install the drivers for this device, clickset to update driver, which starts the Hardware Update Wizard.

  ==================================================================

  Those who might be ghosts then right click on them and UNINSTALL - devices and then RESTART.

  References to Vista also apply to Windows 7.
  
  If they show upward then try to manually install the drivers.

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system.
  For each driver in the list, additional useful information is displayed: load address of the driver,
  Description, version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - device - Graphics Manager - note the brand and complete model
  your video card - double - tab of the driver - write version information. Now, click on update
  Driver (this can do nothing as MS is far behind the certification of drivers) - then right-click.
  Uninstall - REBOOT it will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party
  with their own software and drivers and all other main drivers that you have.

  Now in the system manufacturer (Dell, HP, Toshiba as examples) site (in a restaurant), peripheral
  Site of the manufacturer (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for
  BIOS, Chipset and software updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after
  each installation.

  Always check in the Device Manager - drivers tab to be sure the version you actually install
  presents itself. This is because some restore drivers before the most recent is installed (sound card drivers
  in particular that) so to install a driver - reboot - check that it is installed and repeat as
  necessary.

  Repeat to the manufacturers - BTW in the DO NOT RUN THEIR SCANNER device - check
  manually by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers to 7 (update drivers manually using the methods above is preferred
  to make sure that the latest drivers from the manufacturer of system and device manufacturers are located)
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver under Windows
  Updates, that leaves about Windows updates but it will not install the drivers that will be generally
  older and cause problems. If updates offers a new driver and then HIDE it (right click on it), then
  get new manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Battery not present

  Hello! I have a HP elitebook 8440p. The battery meter indicates that my #2 battery is not present and when I unplug my computer is shut off.  I tried to take out the battery and replacing but that has not worked.  I read that re-installation of compatible microsoft ACPI control method battery can help but I didn't know if that applied to my situation.  Can someone help me?

  Hello amj205. I understand that your battery is not detected. Is this correct?

  I believe uninstalling the driver ACPI is a good place to start. I combined this relocation with a hard reset, so be sure to follow these steps exactly.

  1. Open (with power sector and battery) Device Manager.
  2. Expand the section of the battery.
  3. Uninstall all listed here compenants.
  4. Shut down the laptop.
  5. Remove the battery and AC power.
  6. Press and hold the power button / stop for a minute.
  7. Replace the battery ONLY.
  8. Start Notepad and allow Windows to reinstall the drivers.
  9. Check that this action has resolved the problem and display the result.

  Let me know the result. I hope you have a great rest of the day!

• Error 1222: The network is not present or not started

  I have a home network with two computers. I've implemented such that file, internet and printer shares, a set-up that has worked well for a while. All of a sudden, I could not access the computer on which the printer is connected to everything. This computer, however, was still able to access the internet, but not able to access its own location on the computer network. I ran the Diagnostics of the network and the convenience of homegroup without result. I discovered that the Server service is not running and tried to start, but rather, I got the error "Windows could not start the Server service on Local computer. Error 1222: the network is not present or not started. "LAN diagnostics donnГ not answers. After the Server service does not, I cannot share files or printer, but can somehow get internet to share.

  Help, please. Thank you

  Hello

  Maybe this can help, http://support.microsoft.com/kb/170336

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• I can't get my attachments to open, for example to open an attacment real estate form to show me a picture of a habit of the House, what can I do? Thank you

  I can't my attachment to an e-mail to me to open, for example, real estate, of that I'm sent me some pictures of houses but I can't seem to open. What can I do? Thank you CG-942

  Save the attachment to the office and see if you can open it by clicking on it.  If not, then right-click on it and see what is the file extension and that help you find which program you may need to open it with.  If it is a pdf file, then you must have Acrobat Reader on www.adobe.com.  If not, ask your real estate agent what format the pictures are in?  If you can't see all the images in emails, then see www.oehelp.com/noimg.aspx

  Steve

• "the network is not present or started" after the execution of the configuration of the network. Why?

  I have a laptop that I used it on a network of small business with printers shared running a Microsoft network.   I was able to see the hard drives, printers, files and folders on the other machines for the past year, without problem.

  I recently installed Norton Internet Security Suite and since this operation were not able to connect to the local network< but="" i="" have="" full="" internet="" access. ="" i="" can="" see="" the="" router="" and="" surf="" the="">

  When I click on the already mapped network Drives (Y and Z on my computer) I get the following popup error:

  An error occurred while reconnecting Z: to \\servername\mydirectory

  Microsoft Windows Network: The network is not present or started.

  This connection has not been restored.

  So I tried to debug as follows.

  I called Norton.  They compeltely uninstalled after internet security and reinstalled using smart firewall.
  (It does not)
   
  I disabled Norton and tried to update the drive netowrk / reconnection
  (It does not)

  I disabled Norton and represented the Network Setup Wizard. Rebooted, tried to reconnect
  (Which did not).

  whenever I tried to connect, the error message.

  If the Windows network turned then how can I access the network?

  I don't see all the computers on the network.
  I can not connect to the printer, I was connected previously.
  The drive mappings, I set up back same Netowrk not started error when I click on them.
  There is no other computers on my network
  I have the same workgroup name (MSHOME) as other computers that CAN share resources.

  I use a Compaq Presario M2000 laptop
  Running Windows XP Home Edition (SP 3)
  trying to connect to a Waindows XP Home w / shared desktop printer.

  Thoughts, suggestions?

  Found the answer

  A friend who did the same thing.

  Notes: Microsoft Windows Network: the network is not present or not started

  
  "I started to see this message on a Windows XP SP2 computer, but not on the other in the same room. I couldn't understand why it was happening I was watching the Samba server to connect, and the machine was not connect at all. In addition, this specific message was not really on the Web.

  The answer is quite simple - run services.msc and enable the Workstation . I had turned off, rebooted and forgotten on this subject. »

  found the answer here:
  http://perljam.NET/notes/Microsoft-Windows-network-the-network-is-not-present-or-not-started/

  DOH

  My apologies.  I'm REALLY surprised that I couldn't find the answer on the forum to help here.  But now, it's here.  Hope this helps someone else who has the same problem and cannot find the solution.