Problems of configuration of IPTV, WRT1900ACS.

Similar Questions

• My laptop is one of the 4 home cannot connect to the internet, it's Vista and it has connected w/Ethernet no problem, I called Xfinity tech, that says, is the problem of configuration! Can you help me?

  Acer laptop, Vista is, she can connect wirelessly with my friend modem but my house, she can't, I use the service of Comcast, they checked the modem is fine, they think that the problem of configuration! I'm not computer too, thank you!

  Ryan (Shih Chi)

  Hello

  How do you try to connect the computer to the House? Wired
  or wireless?
  Try the methods provided and see if it helps to solve the problem.
  Method 1:
  Check out the link and follow the troubleshooting steps in the article.
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows
   
  Method 2:
  If you try to connect to t Wireless net work then refer to this link and follow the steps.
  Connect to a network with Windows Vista wireless
  http://TechNet.Microsoft.com/en-us/library/bb878035.aspx
   
  Method 3:
  Reset TCP/IP on your computer and check. Check out the link and follow the steps.
  How to reset the Protocol Internet (TCP/IP)
  http://support.Microsoft.com/kb/299357
   
  Method 4:
  You can also visit this link and follow the steps.
  
  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us
   
  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756/ ) how to back up and restore the registry in Windows

• Problems to configure FireFox to use a CAC reader

  I'm trying to set up Firefox so I can use my CAC card with her reader. My problem is when I try to load a module under Tools > Options > advanced > encryption > safety devices. When I try to load acpkcs201.dll (or any other other .dll files) I get an error message that says: "unable to load the module.

  When I try to use the add-on DoD configuration 1.2 of forge.mil, it is also unable to do this configuration.

  The ACC Player and the software works well in Chrome and IE. The only problem is the .dll file does not load in Firefox using the add-on or manually.

  Does anyone know how to make the module load correctly?

  I use:
  Windows 7 x 64
  Firefox 3.6.9
  SCR331 card reader
  ActivClient 6.2

  I met the same problem at first. I tried to load the *.dll files in obvious location - C:\Program Files\ActivIdentity\ActivClient. None of the files acpkcs*.dll and implement. Then I realized that the current version of Firefox is always a 32-bit program - it can not load the ActivClient 64-bit drivers.

  Try loading C:\Program Files (x86)\ActivIdentity\ActivClient\acpkcs211.dll instead. This has worked for me - the charge immediately *.dll and detected my ACC Player. I was able to successfully access the CAC restricted without any problem sites.

  My configuration:
  Windows 7 Professional x 64
  Firefox 3.6.10
  ActivClient 6.2.0.74 - BINDINGS 1002012

• D20 problem of configuration of Windows Server 2008 R2 / 1 x SATA HD / 4 x SATA SSD

  Hi all

  I have a Mod D20. 4155 and want to use next to it is by default SATA HDD SATA SSD four disks of virtual machines. Windows Server 2008 R2 will be the OS with the use of its Hyper-V features.

  I have Aproblem with detection of drives in the configuration of the operating system. All 5 disks are visible in the Marvell controller BIOS setup. It is possible to configure a RAID on the SSD, etc, but I don't "see" any disk in the configuration of the operating system. I tried to load additional drivers in the part of the Setup utility GUI, but it did not work. I tried with the driver Marcell SAS and Intel Matrix driver, both located at http://www-307.ibm.com/pc/support/site.wss/migr-72280.html.

  Suggestions for the BIOS of the PC / BIOS Marvell / OS installation configurations?

  Best regards, Chrischmi

  Hi all

  I found the solution myself. After detection, the default drive is a SATA drive (and), I got the idea to test it on the Intel SATA controller. It was possible to install the spirit of the machine the disks attached to the Intel controller. After installation, I went to Device Manager and installed the driver of Lenovo Marvell, rekindled the Marvell controller disk and started the. Successfully. Yes!

  On my way to the solution, I had another problem: in the setup of Windows GUI part, I got an error of 0 x 80300001 with Lenovo's Intel SATA driver. It was not possible to install windows Server on the SATA drive with reason0x80300001. very helpful post, Microsoft! (-) I decided to use the default Microsoft for the Intel SATA controller driver after a reboot. Installer executed well, but ended with an error 0 x 80070017 and problems of copy of (unknown) files. The solution (found after a few hours...) was to burn a new installation of Windows Server DVD. I don't want to talk about it anymore...

  -Christoph

• Problem in configuring the type of columns in a table

  I have a problem with Labwindows 2009
  I want to put a table with two columns, each with a different type.
  I need a numeric column and a string column.
  The problem is that I can't configure each of the types in the Edit menu of the table.
  If I set the type of the first column in the Numeric form, this becomes automatically equal.
  Can someone help me?

  Support persons OR confirmed to me that I want to do in version 2009 cannot be done.
  The way to do it would be to create a column and set it with the desired type. Then delete and re-create and so on for each column that you need.

• Have a problem teleworker configuration

  Hello

  I have a problem with the configuration of the teleworker. After I installed ISA570w at Headquarters, I installed also ISA570w to the factory.

  The configuration seems correct. ISA at the factory can make the tunnel with ISA VPN at the main office.

  I try to test on the side of the factory of ping to the server at the main office but ping failed

  I don't know what I have to to allow ACL LAN - VPN and VPN - LAN side or not?

  Ronald salute, please use our forum, my name is Luis I'm part of the community of support to small businesses. You can try to configure an ACL allowing your WAN (factory) remote access to your local network (server), this configuration must be defined in your desktop device.

  Let me know if it works for you,

  I hope you find this answer useful

  Greetings,

  Luis Arias.

  Support of Cisco network engineer.

• Cisco RV220W IPSec VPN problem Local configuration for any config mode

  Dear all,

  I need help, I am currently evaluating RV220W for VPN usage but I'm stuck with the config somehow, it seems that there is a problem with the Mode-Config?

  What needs to be changed or where is my fault?

  I have installed IPSec according to the RV220W Administrator's Guide. Client's Mac with Mac Cisco IPSec VPN, I also tried NCP Secure Client.

  I have 3 other sites where the config on my Mac works fine, but the Cisco VPN router is not.

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: remote for found identifier "remote.com" configuration

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: application received for the negotiation of the new phase 1: x.x.x.x [500]<=>2.206.0.67 [53056]

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: early aggressive mode.

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received Vendor ID: RFC 3947

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received Vendor ID: draft-ietf-ipsec-nat-t-ike-02

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received Vendor ID: draft-ietf-ipsra-isakmp-xauth-06.txt

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received Vendor ID: CISCO - UNITY

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received Vendor ID: DPD

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: for 2.206.0.67 [53056], version selected NAT - T: RFC 39472013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: floating ports NAT - t with peer 2.206.0.67 [52149]

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: NAT - D payload is x.x.x.x [4500]

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: NAT - D payload does not match for 2.206.0.67 [52149]

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: NAT detected: Peer is behind a NAT device

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: request sending Xauth for 2.206.0.67 [52149]

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: ISAKMP Security Association established for x.x.x.x [4500] - 2.206.0.67 [52149] with spi: 1369a43b6dda8a7d:fd874108e09e207e

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: type of the attribute "ISAKMP_CFG_REPLY" from 2.206.0.67 [52149]

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: connection for the user "Testuser".

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: type of the attribute "ISAKMP_CFG_REQUEST" from 2.206.0.67 [52149]

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] WARNING: ignored attribute 5

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] WARNING: attribute ignored 28678

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] WARNING: attribute ignored 28683

  2013-03-07 01:56:07: [CiscoFirewall] [IKE] INFO: purged-with proto_id = ISAKMP and spi = 1369a43b6dda8a7d:fd874108e09e207e ISAKMP Security Association.

  2013-03-07 01:56:08: [CiscoFirewall] [IKE] INFO: ISAKMP Security Association deleted for x.x.x.x [4500] - 2.206.0.67 [52149] with spi: 1369a43b6dda8a7d:fd874108e09e207e

  Hi Mike, the built-in client for MAC does not work with the RV220W. The reason is, the MAC IPSec client is the same as the Cisco VPN 5.x client.

  The reason that this is important is that the 5.x client work that on certain small business products include the SRP500 and SA500 series.

  I would recommend that you search by using a client VPN as Greenbow or IPSecuritas.

  -Tom
  Please mark replied messages useful

• RV 120W problem (cannot configure the router)

  Hello

  I just installed a new RV 120W to replace my dlink router.

  The problem is that I can't view site configuration (192.168.1.1)

  My internet works fine and when I go to 192.168.1.1 I can log in (with the password I set using the installation disc) but then I see the top of the site config (blue) but where the Control Panel must be I see "site cannot be displayed."

  I tried to use my laptop and pc on ports diffirent.

  I ve tried using IE9 and Chrome version 16,0,912,63

  I ve also tried to reset the router, but this has no effect.

  Can you please specify? Thank you very much!

  Kind regards

  Jesse

  Have you tried https://192.168.1.1/

  ?

  (https or http).

• problems of configuration-esxi

  Hello

  I'm having a problem with the script configure esxi.

  I have two vCenters, two 5.1.0 build 947673. A vCenter contains 4 hosts, 32 other hosts.

  The following has worked flawlessly and configured 4 guests without error. All 4 hosts are visible in the journal MISTLETOE Insight...

  Configure esxi - u vimanager s vmvchomapp05.domain.com.au t 10.80.9.116

  vmlihdp1: ~ # Configure-esxi - u vimanager s vmvchomapp05.domain.com.au - q

  Password:

  Querying the settings of the remote host to vCenter Server log: vmvchomapp05.domain.com.au

  NOTE: Configure esxi will work methodically but not quickly. Large stocks

  or slow network connections will be more slow down execution. Please be patient.

  Trying to connect to vCenter Server vmvchomapp05.domain.com.au

  Host: esxhdhsp3.domain.com.au, VMware ESXi 5.1.0 1021289

  Syslog.global.logHost: "10.80.9.116".

  Host: esxhdhsp4.domain.com.au, VMware ESXi 5.1.0 1021289

  Syslog.global.logHost: "10.80.9.116".

  Host: esxhdhsp10.domain.com.au, VMware ESXi 5.1.0 838463

  Syslog.global.logHost: "10.80.9.116".

  Host: esxhdhsp11.domain.com.au, VMware ESXi 5.1.0 838463

  Syslog.global.logHost: "10.80.9.116".

  However, against the 2nd and biggest vCenter, I get the following...

  Configure esxi - u vimanager s vmvchomapp03.domain.com.au t 10.80.9.116

  Password:

  Configuration of the hosts connected to vmvchomapp03.domain.com.au to send logs to 10.80.9.116

  NOTE: Configure esxi will work methodically but not quickly. Large stocks

  or slow network connections will be more slow down execution. Please be patient.

  Trying to connect to vCenter Server vmvchomapp03.domain.com.au

  Host: esxbohsp1.domain.com.au, VMware ESXi 5.1.0 1065491

  WARNING: VMware ESXi 5.1.0 1065491 has a known issue where a remote syslog destination becomes

  unavailable host will cease to send remote syslog messages until the syslog server is

  restarted. Please note that tcp/ssl also encounter this problem.

  *** See http://KB.VMware.com/kb/2003127 for more information.

  ERROR: Format not supported < syslog >

  Other things I noticed are:

  Query the vCenter or a currently configured host setting works very well

  If there is a crowd of syslog configured on the host, or not makes no difference. Error continues to be.

  The format of < syslog > makes no difference, ipaddress, udp://ipaddress:514, hostname all fail

  I note that Configuration > >of the software Advanced settings > > Syslog.global.loghost in the vSphere Client of the Syslog is empty for the properly configured hosts. I guess that's normal behavior. /etc/vmsyslog.conf is correctly configured

  I have read the log files in/var/log/loginsight and do not see anything which is useful for my troubleshooting.

  Any help with this problem would be greatly appreciated.

  See you soon

  1. Yes this is the expected behavior. ESXi 5.x support several loghost entries and to ensure that a user does not accidentally remove old entries loghost configure esxi requires a separate command to remove a loghost. ESXi 4.x does not support a single loghost and configure esxi is delivered with the f flag to replace the existing entry. You will notice when you use - help t will configure a syslog target. This distinction is important because t can be used for adding more than a target of syslog. For example, if you have a loghost configured 10.10.10.10, then try to add tcp://10.10.10.10:1514 then configure esxi will change 10.10.10.10 to tcp://10.10.10.10:1514 rather than add a second entry.

  2. configure esxi is provided as a tool for individuals to use, which is particularly useful for people who do not have existing scripts and exploit no profiles of the host. If you have an existing script or host profiles so feel free to use them.

  3. I assume you mean when configure esxi detected what he thought was a malformed loghost. Thanks for the comments, I'll make sure it is considered for a future version.

• Problems with configuration properties and the java plugin

  Hello
  
  I have test the java plugin from the hyperic documents. Autodiscover works very well. Now, I had the problem if I want to change all "configuration properties" I get following error message:
  ' The configuration has not been set for this resource due to: invalid configuration: error reported by Agent @ 141.73.130.146:2144: java.lang.NullPointerException.
  Wait I use properties by default, then I don't get any errors.
  
  What is the problem?
  
  MyAutoDiscoveryServerDetector.java
  ---------------------------------------------------------------------------------------------------------------------------
  SerializableAttribute public class MyAutoDiscoveryServerDetector extends ServerDetector implements
  
  {AutoServerDetector}
  
  public list getServerResources (ConfigResponse platformConfig)
  
  get {PluginException}
  
  Server list = new ArrayList();
  
  Server ServerResource = createServerResource ("My Auto-Discovery Server->" + (x + 1));
  
  ConfigResponse productConfig = new ConfigResponse();
  
  productConfig.setValue ("myTimeout", String.valueOf ((x+1) * 1000));
  productConfig.setValue ("myUrl", "http://127.0.0." + (x + 1));
  productConfig.setValue ('Description', 'Description - my Auto Discovery Description->' + (x + 1));
  productConfig.setValue ("myValue", 10);
  
  server.setProductConfig (productConfig);
  
  Servers.Add (Server);
  
  return of the servers;
  
  }
  ---------------------------------------------------------------------------------------------------------------------------
  
  HQ - plugin.xml
  ---------------------------------------------------------------------------------------------------------------------------
  <? XML version = "1.0"? >
  < package = "com.citytechinc.articles.hyperic.plugin plugin" >
  
  < name of the filter = "domain" value = "My Auto Discovery" / >
  
  < name of the server = "MyAutoDiscoverServer" version = "0.1 c" platforms = "Unix, Win32" >
  
  < plugin type = "autoinventory" class = "MyAutoDiscoveryServerDetector" / >
  < plugin type = 'measure' class = "MyAutoDiscoveryServerMeasurementPlugin" / >
  
  < config >
  
  < name of option = 'myUrl '.
  
  Description = "Enter the URL for this resource"
  
  " default = ' http://127.0.0.1 "/>
  
  < name of option = "Description".
  
  Description = "enter a description of this plugin"
  
  default = "default my Auto Discovery Description" / >
  
  < name of option = "myTimeout."
  
  Description = "time-out for something in my plug-in.
  
  default = "0" / >
  
  < name of option = "myValue"
  
  Description = "a metric value.
  
  default = "10" / >
  
  
  < / config >
  
  
  < name metric = "availability".
  alias = 'availability '.
  Template = "System.avail:type = Platform:Availability"
  category = "AVAILABILITY".
  indicator = 'true '.
  collectionType = "dynamic".
  units = "percentage" / >
  
  < name metric = 'value '.
  alias = 'value '.
  model = "" MyPlugin:Type = value: value ' "
  category = 'USE '.
  indicator = 'true '.
  collectionType = "dynamic".
  units = "none" / >
  
  < / Server >
  
  < / plugin >
  ---------------------------------------------------------------------------------------------------------------------------

  UM,.

  This must be due to an incompatibility between the definitions of plugin in the server (and/or of the database) and the agent.

  First of all, always check the server log, errors that appear it should lead to the cause.

  The plugin xml initialized ok on the server, or any error appear?

  You go to Administration-> default trace and see your plugin (Server Type: MyAutoDiscoverServer) and everything is there?
  If this isn't the case, errors occurred when starting the server, check the log.

  Did you start to shave - created the plugin, added to both server and agent, autodiscovery, the platform/server added in Hyperic - or you already had the server/platform added in Hyperic and who has made some changes in the xml plugin that may be in conflict with what is already in the Hyperic database?

  Generally the pitfalls that come from these errors.

  Been there, done that.

• Get the problem when configuring Application adapt to Weblogic

  Hello
  I am following this doc http://docs.oracle.com/cd/E15523_01/ doc.1111 /e17054/install.htm for installation and configuration of Application Adapter for Oracle Weblogic Server, but since the Application Explorer, I get the following error.
  
  http://3.BP.blogspot.com/-X1S8b2rDYMk/UWuirzDovXI/AAAAAAAAAiI/X_zxgu_LDfM/S1600/AppExplorer1.jpg
  
  It's the application Explorer command line
  
  http://2.BP.blogspot.com/-s-NephexVVI/UWuitzLcmvI/AAAAAAAAAiQ/aa2miqdccq4/S1600/AppExplorer2.jpg
  
  Please help me with this problem.
  
  Thank you
  
  Nasir

  Hello.
  Well, it seems that you have active is the application of the JCA, not the Servlet IBSE.

  Could u pls try to make a JCA connection?

  Follow this doc http://docs.oracle.com/cd/E14571_01/doc.1111/e17656/config.htm#BABJIDGD

  The best

• [EMP Configuration] OracleDB - problem of Configuration of OC4J... not found

  Hello
  
  Constantly reviewing the existing solutions for this issue, I find that mine is not yet displayed.
  
  Intro
  In order to install EPM, I had to install Oracle Database 11 g. After installation, an error has occurred, stating that configurations were not saved and I could manually run "ECMA.bat" later.
  I tried to configure by creating environment variables such as:
  -ORACLE_SID
  -ORACLE_HOSTNAME
  -ORACLE_UNQNAME
  
  So far, I have not tried to run ECMA.bat for the last time, because I'm sure that I will not fail due to not recognize the host name.
  
  
  The question
  Whili trying to make sure that the database is properly set up, I tried to access the Web page, to no avail.
  Then, I found my problem in the forums:
  
  When I type cmd:
  
  -> (Type I)
  C:\OracleDB_app\alexandreyin\product\11.2.0\dbhome_1 > emctl status dbconsole
  
  -> (returns)
  OC4J Configuration problem. C:\OracleDB_app\alexandreyin\product\11.2.0\dbhome_1/o
  c4j/J2EE/OC4J_DBConsole_HPCM. Lab.pt_orcl not found.
  
  
  In fact, there is no file with this name, or something like "/ OC4J_DBConsole_localhost_orcl" suggests that many positions.
  I only have folders like:
  -' House '.
  -"oc4j_applications".
  -"OC4J_DBConsole".
  -"OC4J_Workflow_Component_Container".
  -"OC4J_Workflow_Management_Container".
  -"utilities".
  -"deploy_db_wf".
  
  Some posts suggesting to change me my file/driver/etc/host, but I think that my current file is correct:
  
  -> (Contents of host gile)
  127.0.0.1 localhost
  XX.XXX.XXX.XXX HPCM.lab.pt
  
  
  Honestly, I'm out of ideas and I wish all experienced colleague could give me a hint.
  
  
  Thanks in advance

  Hello

  It is useful to have a look at the next on Oracle support document.

  Problem - emctl start dbconsole fails with the problem of the OC4J Configuration OC4J_DBConsole__ not found error * [555218.1 ID] *.
  Linux 64-bit DBConsole fails with "cannot find/oc4j/j2ee/oc4j_DBConsole_... OC4J Configuration problem ' * [462325.1 ID] *.

  Thank you
  HyperEPM

• Toshiba Satellite M60 - problem sound configuration for the external speakers 2.1

  I just bought:
  "Creative I-Trigue 3400" 2.1 channel PC speakers for my PC laptop Toshiba M60.

  My problem is that there is no sound in the right speaker.

  * Headphone/onboard speakers work very well
  * I have updated its (Realtek AC97) card drivers
  Creative speakers work fine with my I - Pod
  Creative speakers work fine with my laptop less expensive/Sour.

  I have experimented with the settings of his Panel, including settings of Toshiba virtual sound without success.

  any help would be appreciated.

  Closer examination, I noticed that there is a slight (millimeters) overlooking 'lip' above the headphone jack.

  The creative speaker comes with a heavy input jack which gets partially blocked by this fake - my input cable using cheaper "thinner" solved my problem.

• Problem in configuring IP address in the target of RT PC desktop

  Hello

  I use PC industrial (IMB Q670 R21) than my goal of RT. It has two ethernet ports, which is compatible with LabVIEW RT. I created the USB Utility with LabVIEW 2012 and formatted HARD disk drive. The PC boots into safe mode, but the IP settings are not reset to 0.0.0.0. The same HARD drive previously used on another target PC RT with LabVIEW RT programs worked very well. I need two RS232 ports on target RT so I changed my target computer and try to use as target RT.

  The problem now I face, is that the IP address is not set to host PC MAX. Even if I use a USB drive utility to reset the IP address, it is not 0.0.0.0 that's rather 169.254.25.246. This address is also not even identical to the previous target of RT. The error I get in MAX "a problem in the recording of your settings. I tried with ethernet hub as well as crossover cable with different addresses.

  Need help.

  Rashmi

  Hi RashmiM,

  Connect your PC to the PC RT using crossover cable and change the settings via NI MAX in your PC. Before doing all this, have you tried disabling your firewall (not your RT PC) PC? If you do not, please disable the firewall before you continue. This is possibly due to your firewall or antivirus or both.

  Some additional notes:

  http://digital.NI.com/public.nsf/allkb/72AE8CADA1AF075686256A16005D55B1?OpenDocument

  http://www.NI.com/white-paper/4480/en/

  Warm greetings,

  Lennard.C

• Problems of configuration of remote desktop in windows 7

  I am trying to configure remote desktop settings, but the three options under remote access does not appear. I use windows 7 ultimate, 64-bit, two monitors, the account has a password and there is no update available. I have attached a screenshot with the property system and access remote configuration tab thanks.

  

  Hello

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.

  http://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w7itpro