Number of devices for a user

Similar Questions

• How we happen to know that the number of presents for this user database

  How we happen to know that the number of presents for this user database.
  Both those who are connected and not connected yet.
  
  Thanks in advance
  
  Concerning
  SUBJ.

  using v$ session...

• Practice number of devices for EA3500

  I have a question about a practice number of devices that may be taken in charge for by my EA3500 router.  I currently have 9 devices almost always wirelesly.  My ISP is 20 Mbps down and 5 members to the top. I noticed that the default maximum number of devices is 50, which is extremely high.

  Because all devices are activley download / download continuously, what are your thoughts on a number of devices resoanable.  In my case, three of the devices are used for streaming music/movies (they are the highest priority), the others are for the general internet communication.

  During visits to the family, I could have up to 6 more smart phones that use the connection of comments.

  Any advice?

  Bill

  The typical rule for residential Linksys routers would be 32 wireless clients. LAN clients can be as much as you have available IP addresses in your DHCP Pool.

  IMO, the reality is that once you get on 30 devices (depending on each load of the device) on a single residential router, they can start to be overworked. To what point adding Wireless Routers\Access Points to a part of the large workload hand router is a good idea. Once you get above 50 devices, you should consider moving in ranges of products SMB as a dedicated router wired (no WiFi) and Access Points. SMB devices are designed to handle workloads higher than residential products and they offer more features like advance VLAN, set subnet IP, Custom, routing, ACL, QOS, and virtual SSID. These technologies give you more control on how bandwidth is used and routed.

• Is it possible to hide a conditional function in responsibility. Say it together a small number of users, I need the function display and for some users, it must be hidden.

  Is it possible to hide a conditional function in responsibility. Say it together a small number of users, I need the function display and for some users, it must be hidden.

  Hello

  The normal thing to do is to create a similar additional responsibility and using Exclusions to 'hide' the features you want.

  Then assign it to restricted users.

  Kind regards

  Bashar

• I have a number of licenses for AcrobatPro, one of my users PC crashed, I need to install on a PC, replacement will be show up as several PC on a license

  I have a number of licenses for AcrobatPro, one of my users PC crashed, I need to install on a PC, replacement will be show up as several PC on a license?

  Hi davids75107426 ,

  You can do this if the users PC broke down.

  It will not be displayed on the other multiple licenses.

  Concerning

  Sarojini

• Error number reserved for the user

  Dear Sir

  In my sweet, I use the cluster of error defined by LabVIEW

  Y at - it a series of numbers reserved for the user.

  Thank you

  Massive

  Help:

  Error codes 5000 to 9999 and-8999-8000

  http://zone.NI.com/reference/en-XX/help/371361B-01/lvhowto/creating_user_defined_erro/

  And als

  500 000 to 599 999

  http://forums.NI.com/NI/board/message?board.ID=170&message.ID=410869&query.ID=3477275#M410869

  Felix

• Toll free number for new users

  Hi all

  My v25 update comes to pass through and the main feature of my client wanted was the ability for new users to get the latest issue for free. This feature doesn't seem to work. I the auto download button when generating App checked but when I installed it on an iPad that has never had the app before, he started an automatic download, nor was the issue available for free.

  I do something wrong or the feature does not work?

  If anyone has a few minutes to test, the magazine is The Wilson Quarterly (https://itunes.apple.com/us/app/the-wilson-quarterly/id530320024?mt=8)

  Thank you

  -Scott

  I downloaded the application, and the first Folio free function did work for me, either. (I was disappointed that the app is named after Woodrow Wilson and not volleyball Wilson).

  It works in an application I created, called the landscape of the Northwest. I wrote a post about this feature, and Colin has created a video.

  http://blogs.Adobe.com/indesigndocs/2013/02/DPS-subscription-options.html

  I guess that you have selected the option in the tool Admin account and not just in the DPS App Builder.

  

• RV082 bypass the filter for a user

  I have a client asked me to restrict access to a certain number of works not related sites. Easy, stuck using firewall > content filtering. Then I was asked to disable this filter for a single user (general manager) so that it can access eBay.

  I am familiar with this on a Netgear device, but so far my efforts with the RV082 failed.

  First of all, I tried using DHCP in order to reserve an IP address for this user, then setting "Access rules" so that this IP has all access all the time, but it doesn't seem to work.

  I assumed that setting this IP, as the demilitarized zone would achieve what I want, but it seems overkill and not very wise security.

  Can someone help me with this please?

  concerning

  Adam

  Adam, the RV082-based content filter does not support your described scenario. However, the ProtectLink Web subscription allows you to specify some IP corrects to be exempted by the url filter.

• Handspring Visor is a "unrecognized USB device" for Windows XP

  Hello World-

  I feel as if I have a career to synchronize my PDA hot! I used to hotsync regularly on my old HP Windows 98 machine, and now that I have this new (er) eMachines Windows XP Pro system, I got nothing but heartache. Here's the situation:

  My Visor Deluxe runs Palm OS 3.1H3, apparently the latest version which will work with it. The computer is running Windows XP Pro SP2. I have hotsync a few times when I got to the computer, but it has never been reliable. Now I surely CAN NOT synchronize! When I press the button on the cradle, Windows hotsync ALWAYS reports, "USB device not recognized" and of course the visor says he couldn't make contact with the office.

  HotSync manager is running (I have the blue and red arrow on the taskbar icon), and if I look at the Device Manager when I try to sync, is apparently trying to get the driver, he simply painted the same list. The list does NOT include the Palm, Handspring or unknown devices.

  I followed the directions "clean uninstall" I found on this forum and re-installed Palm Desktop 4.01. That worked once a week or two ago, but now when I arrive at the end of the installation, when I'm supposed to hot sync, I get the error not recognized USB.  I even tried to install Palm Desktop software version 6.2, but which ended up in a mess - I was getting errors like "Ordinal 23 could not bewildered because of the trajectory messed up', or words to that effect... I think it's ok for XP, but not "peripheral" as my trusty old visor :-)

  I know I should try to use the same configuration on another computer to be sure that the visor is ok, but I don't have access to another machine; In addition, the PDA has no other wierdness. Soft resets do nothing, but I don't want to try a hard reset until I get everything synced to the top! I am at my wit's end and don't know what else to try. I tried both my cribs and a number of different USB connections both at the front and the back of the PC. The USB hardware in the computer seems to be fine with everything else - mouse, camera, mp3, flash drives. I'm beginning to suspect that I need to plug with USB 1 and these are 2 USB, but I don't know how to check either of these things, or how "throttle" in the case, I have to use the USB as soon as possible.

  Thanks in advance to everyone that these figures. I'll be very grateful to have everything works again.

  Gary Benson

  I was with you until the end. I hate to ask, but could you clarify this just a little:

  Then, reinstall your Palm desktop from the CD and do a hotsync. If she asks
  for a user name and you synchronized your device before you put "test" If you "
  no sync before creating a hotsync name.

  Ok. I read three "if" statements, and try to understand what is meant here. If they ask you a user name AND if I synced before, AND if I do not synchronize before creating a hotsync name, I put in 'test '. Means I can't use the name I used for this camera? Or are you suggesting that, really, should I open Palm Desktop and create the username before I hotsync for the first time (after the new installation)?

  I * have * synchronized before, and I don't plan to sync until everything is set up right, which to me should mean that Palm Desktop is ready with a username to match your handheld.

  Also, these indications seem in conflict which advised you to in the first paragraph, where you said:

  When you install Palm desktop, skip the hotsync process and complete the installation. After installation, adjust the conduit in hotsync manager for handheld overrides desktop, then synchronize with PC. During the connection process, it will ask you a username, enter the same username which is located in the upper right of the screen on your handheld hotsync.

  It * seems * that what you say I have to do is:

  (A) clean uninstall - move data to safe places, uninstall, and then remove all traces of "Palm" and "Handspring" of the registry.

  (B) restart the computer.

  (C) install Palm desktop, but not hot sync again.

  (D) open Palm Desktop, add the user name (Tools/users) and set the lines for handheld overrides Desktop.

  (E) hot sync.

  Isn't it? Sorry to be so simple, but I want to make sure to proceed exactly right. Thank you very much for your reply and for your help.

  -Gary Benson

• Limit the number of devices

  Hello

  I would like to ask if it is possible to limit the number of devices on which ebook could be read. For example, our client is a school with 20 PC and an AdobeID. Is it somehow possible to limit the number of devices to 20? In the console "Admin" there is only "A Single Device" yes/no limitation.

  Thank you

  Dušan

  No, you have a choice of licenses for the content of the device (and one user), or only content to the user of the license.  If allow you the user, they can read the content on all of the machines that they have authorized (the approximate limit is 6 computers and handheld devices 6, but it grows slightly over time to take account of computers/devices lost/updated).

• Need to disable CGI, I have two-factor authentication, but I don't have the phone number or device with me. What can I do?

  Need to disable CGI, I have two-factor authentication, but I don't have the phone number or device with me. What can I do?

  For Apple ID - Apple Support two-factor authentication

  If I can not connect, how I again to access my account?

  If you can't sign in, reset your password, or receive verification codes, you can account recovery application to restore access to your account. Account recovery is an automatic process designed to help you back into your account as soon as possible while denying access to anyone who might be impersonating you. It may take a few days - or more - depending on the specific account information, you provide to verify your identity.

  It will be your option. If you try to find an iPhone with locking Activation that you don't remember the password, you can remove the account from the iPhone with the help of Apple's Support with the receipt of the initial purchase of the iPhone as a way to prove that you are the real owner of this iPhone.

• configuration of IQ / number of samples for USRP2920

  Hello

  I tried to save the HF Signal using the USRP 2920. I had an unexpected behavior for certain configurations of IQ rate and number of samples.

  When you set the IQ for 1 M as an example and numbers of samples to 60984, the saved file long empty even after recording over a long period of time. It seems that there is an adequate number of sample for a given IQ there is.

  Do someone know the trade off between settings of bo?

  Thanks for your suggestions

  Hi Bolivar,

  With regard to the transmission continues in a loop, I think it could help you to make a small piece of transmission over until you actually begin the continuous transmission immediately in a loop. The reasoning being that small initial transmission could help boot to the top of the Tx buffer and prevent cost overruns due the USRP device waiting for data and do not get it.

  With regard to the relationship between the right size for a given frequency of IQ, I do not have a precise answer at this stage.

  Thanks and good luck.

• Get errors for the user input data filter no KB 911895 HID

  OT: iI have windows xp S/P 3 installed also apple i pad I get errors for the user input data filter no KB 911895 HID
  What should I do to get rid of this popup that wizzard windows keeps giving me?

  Hi Graybeard,

  What is the exact error message you get?

  HID Non-User Input data filter is an optional update. I suggest you try the steps from the following link:

  The screen saver does not start after the installation of a wireless pointing device
  http://support.Microsoft.com/kb/913405

  What version of the operating system Windows am I running?
  http://Windows.Microsoft.com/en-us/Windows7/help/which-version-of-the-Windows-operating-system-am-i-running

  Troubleshooting Windows Update or Microsoft Update when you are repeatedly offered an update
  http://support.Microsoft.com/kb/910339

• Compaq Presario CQ42: Synaptics Touchpad disabled in advanced settings for other users

  Hello

  I have three in my Compaq Presario CQ-42 user profiles, an administrator and others are "user".

  When I fisrt lives the synaptics touch settings window buffer through my first profile "User" 1, in the properties of the mouse-> device-> Synaptics LuxPad V7.4-> settings settings, all the options in this window were available for selection and nobody has been disabled. Now when I go to 'Administrator' profile, some of the options in this window settings are disabled, and seem to be partly hidden. As the option 'Enable the Pinch Zoom in the Pinch Zoom section' and 'Activate Pivot spin turn' seems to be hidden/disabled. To check this, I created the other profile of 'Other users' 2, but without success, and I found the same problem here too. I also tried to uninstall the synaptics driver several times of all profiles, but every time I have re-installed and checked to get the same result. The parameters were only available for the 'User' 1 profile every time and disable for profile administrator and "User 2" profile.

  I can produce the same shots if necessary.

  Please help me to get the solution because I'm very addicted to advanced by synaptics settings.

  Hello Dishat, welcome to the Forums of HP.

  It seems that you need to activate the advanced settings of your touchpad on your laptop, you are only able to do this in a profile, as in the other some options are grayed out. I will try to help you with this.

  To help you more effectively on this issue, could you please provide the following:

  The operating system currently installed on your laptop.
  Model and product numbers on your laptop.

  In the meantime, see if it can help you all: use and configure the TouchPad (Windows 7 and Vista).

  Thanks for posting on the HP Forums.

• Setting up passwords for new users

  I am the Admin of my group. How to create a new user account (for other users) that accepts a default password (an I put) then ask to set up a new password?

  I don't have access to all the operating systems that are past their support life, but I thought that he used the same under Windows 7. Can you type net help user and see what it shows options available?  Maybe Vista doesn't.

  Here are the options I want.

  NET USER
  [username [password | *] [options]] [/ DOMAIN]
  username {password | *} / add [options] [/ domain]
  username [/ delete] [/ domain]
  username [/ TIMES: {both |}] ALL}]

  NET USER creates and modifies the user accounts on computers. When it is used
  without switches, it lists the user accounts of the computer. The
  user account information is stored in the user accounts database.

  user_name is the name of the user account to add, delete, modify, or
  view. The name of the user account can have as much of as
  20 characters.
  password assigns or changes a password for the user account.
  A password must meet the minimum length set with the
  / The command NET ACCOUNTS MINPWLEN option. It can have as
  up to 14 characters.
  * Produces a prompt for the password. The password is not
  displayed when you type it at the password prompt.
  / DOMAIN performs the operation on a domain controller of
  the current domain.
  / ADD Adds a user account in the user accounts database.
  / DELETE Removes a user account from the user accounts database.

  The options are the following:

  Description of options
  --------------------------------------------------------------------
  / ASSETS: {YES |} NONE} enables or disables the account. If
  the account is not active, the user cannot
  access to the server. The default value is YES.
  / HOW: 'text' provides a descriptive comment about the
  the user's account.  Surround the text in
  quotes.
  /CountryCode:nnn uses the operating system country code to
  implement the language files specified for a
  helps the user and the error messages. A value of
  0 means the default country code.
  / EXPIRES: {date |} NEVER} causes the account to expire if date is
  set. NEVER sets no time limit on the
  account. An expiration date is in the
  form mm/dd/yy (yy). Months can be a number,
  statements, or abbreviated with three
  letters. The year can be two or four digits.
  Use forward slashes (/) (without spaces) to separate the
  parts of the date.
  / FULLNAME: "name" is the full name of the user (rather than a
  (username). Place the quote name
  mark.
  /HOMEDIR:pathname sets the path for the home directory of the user.
  The path must exist.
  / PASSWORDCHG: {YES |} NO} Specifies whether users can change their
  password. The default value is YES.
  / PASSWORDREQ: {YES |} NO} Specifies whether a user account should have
  a password. The default value is YES.
  / LOGONPASSWORDCHG: {YES |} No.} Specifies whether users must change their
  password at the next logon. The default value is no.
  / PROFILEPATH [: path] defines a path to the logon of the user profile.
  /SCRIPTPATH:pathname is the place of the user logon
  script.
  / TIMES: {both |} ALL} this is the logon hours. TIME is expressed as
  day [-day] [, day [-day]], time [-time] [, time]
  [- time]], limited to increments of 1 hour.
  Days can be specified or abbreviated.
  Hours may be the rating of 12 or 24 hours. For
  12-hour notation, use am, pm, a.m.., or
  h ALL, a user can still log on.
  and an empty value indicates a user can never
  Open a session. Separate the date entries, time with
  a comma and split several day and time
  entries with a semicolon.
  / USERCOMMENT: 'text' Add or edit the user allows an administrator
  Comment for the account.
  / Workstations: {computername [,...] | *}
  Lists up to eight computers of
  which a user can connect to the network. If
  / Workstations has no list or if the list is *,.
  the user can log in from any computer.