NVIDIA GPU driver does not show up after accidental uninstall

Similar Questions

• Sony Vaio lira is no longer the dvd ram disc, dvd drive does not show in Explorer

  Used to read all DVDs and CDs up to 3 days ago, now cannot read DVD RAM discs, does not even display in Explorer. Just bought new drives, cleaned laser, uninstalled the driver and rebooted to reinstall, followed some difficulties on this Web site, remove filter upper and lower filters in registry entries, as described here. Any help please? Windows XP SP3.

  Hello

  Were there any changes made on the computer before the show?

  I suggest you to return the item and check if it helps:

  How to troubleshoot common problems that occur when a Windows XP-based computer cannot read a CD or DVD

  http://support.Microsoft.com/kb/321641

• Problem with installing Windows on a hard drive, HARD drive does not get detected after installation

  Original title: help with hard drive of the computer.

  Flow of the problem:

  My aunt tried to install windows 7 on the previous copy of windows 8. Needless to say that it doesn't work and it has messed up the hard drive. So, I bought a vacuum. I formatted the hard drive using my other windows computer to have 2 partitions: a boot partition and system partition, and then used the program WinToUSB to install windows on the hard disk. The reason I did it is, because no matter how many times I changed the BIOS in my laptop of aunts, it wouldn't boot from the DVD player to load the windows software. After a few hours, I found WinToUSB. Once windows has been installed, I plugged it into the laptop. For a few hours, I didn't know what to do, because the computer does not recognize the hard drive (he said: "Not detected"). I decided to start from legacy, and then the screen deals

  «intell...» »

  and a bunch of dates, etc all the stuff on the screen to load legacy if you know what I mean.

  He said "not plugged in the media. Check the power cord.

  Then quickly changed screen before I can read almost anything and it goes to the normal windows screen black (with 4 colors). I said to myself, how can he be loading if the hard drive is not detected... Once it is loaded, he brought me to the blue screen (blue screen of death, if you want) I turned the computer on again, always noticing the hard drive was not detected. I ran all the recovery/repair options I could and turned off the laptop. I came back a few hours ago and I loaded the computer again and went into the BIOS.  He said that the hard drive has been detected and said the news about this, as usual. However, at the start of the legacy of windows loading screen, it said still not detected.  I then started to windows to see since it is now detected if that fixes the blue screen. Yet, there is no. I tried to go to the normal windows and screen remains blue. any ideas?

  Hello Chris,

  Thank you for visiting Microsoft Community.

  According to the description, it seems that Windows was not properly installed on the hard drive. I'm not sure how to work the software from third-party manufacturers WinToUSB and reliable installation process is. Microsoft does not recommend using any third party tool to install Windows on your computer, the use of these third-party tools can cause serious damage to your computer.

  I would say to format the hard drive once more and try to install Windows through normal Windows installation process.

  Refer to the section "using the installation option custom if no operating system is installed" in the thread below.

  Installing and reinstalling Windows

  http://Windows.Microsoft.com/en-us/Windows/installing-reinstalling-Windows#1TC=Windows-7

  If you are not able to install Windows on the hard drive at all, I suggest you to contact the hard drive manufacturer to obtain a diagnosis of material performed on the hard drive.

  Do not hesitate to write back for any further assistance with Windows, we will be happy to help you.

• Someone help me please. DVD RW drive does not show up! Win7 32-bit (STARTER)

  I need an answer to this guy. Please, please help me! I can't live without a DVD player for ever!

  PROBLEM:
  Welp, I decieded I hate vista with a passion after getting this laptop to a friend in which I exchanged an electric scooter. So I inevitably found a way to get what I wanted which was Windows 7 (starter, 32-bit). Fortunately, I started to click around and smile that I got my first glimpse of windows 7. Long story short, I discovered that my DVD RW drive was not appear and all the resources that anyone could possibly find on the internet did not work for me. (Fixer, Panel options, registry changes) So I stood up, wiped my tears and decieded to turn to a site of questions and answers.
  CPU CARD:
  Acer aspire 5100
  Most of the default settings
  ALL the default material
  Anyone who responds to this will get a nice, sloppy, virtual me hug :D

  You can try a free program called CDGone.

  You can search on the Internet and download it.

  Read the instructions to learn how to run.

  It is not difficult, it's just different then most of the people are too used.

  If that does not resolve your problem, you may have defective DVD (unit) material.

  Bob

  Computer Clinik LLC

  No luck. Tried almost everything in the book. will try to get just the CardBus vista

• HP Pavilion: Disk drive does not work even after I have installed and uninstalled

  Hello

  The disk drive on my laptop does not work. It does not recognize the CD or DVD. I tried to go into the currency manager and uninstall the drive and scan the image but it does not work.

  This error appears when I look at the properties of disk drives:

  Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19).

  I don't know what else to do.

  Thank you.

  Hello

  Try the rest of the procedure to the title of the subheading resolution - method 3: manually difficulty corrupt registry entries on the link below to remove upper and lower filters and see if that helps the issue.

  http://support.Microsoft.com/kb/982116

  Kind regards

  DP - K

• Windows 7 Ultimate does not show wallpaper after update in Vista Business

  I did the upgrade from Vista business to Windows 7 Ultimate and cannot make a wallpaper of work. I can select only solid colors, but not images or slideshows. I googled for similar problems and it seems people offer various solutions, including through 0 to some attributes of registry related to Active Desktop under HKLM or HKCU Software / Microsoft / Windows / CurrentVersion / policies... And also checking / unchecking a few boxes that appear under easy access control panel, but nothing seemed to help. So I'm a bit lost and it's pretty depressing always focus on the black background, knowing tones of beautiful images are waiting for show it :(
  Can anyone suggest what can be done in this case? New - only full office colors can be changed at this point...

  I finally thought to myself... I don't know which two actions helped, but here's what I did:

  1. I made an order of setwallpaper default under various graphic files pointing to Windows Photo Viewer CLSID extensions (before they were pointing to a different CLSID, which I believe was Office Fax Viewer - {ff609cc7-d34d-4049-a1aa-2293517ffcc6}). Here's how I did it:

  -In RegEdit, I searched "wallpaper" and under HKCR\SystemFileAssociations, he found several extensions (.bmp, .jpg, etc) where I swapped the value for a key 'HKEY_CLASSES_ROOT\SystemFileAssociations\.bmp\Shell\setdesktopwallpaper\Command\DelegateExecute' of {ff609cc7-d34d-4049-a1aa-2293517ffcc6} to {FFE2A43C-56B9-4bf5-9A79-CC6D4285608A}

  - Then he found similar key under HKEY_LOCAL_MACHINE - their values were already set to {FFE2A43C-56B9-4bf5-9A79-CC6D4285608A}, but it won't hurt to check

  2 then I removed the registry key "HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows\Control Panel\Desktop\Wallpaper". This key has an empty value - so I assumed that there is not much use and then shortly after I did it I got my wallpaper of the theme chosen.

• Computers on the local network does not show up after the installation of macOS Sierra

  Shared on my LAN Macs make their appearance is more after the installation of macOS Sierra. See the attached servers is checked in the preferences of the Finder and the computers appear in the list of DHCP clients on the router. I can see these computers to each other. Sharing is disabled on the computer of the Sierra. Any ideas?

  Thank you!

  p.s. I can not even 'go' to the IP address of these computers.

  Correction: I can afp: / and vnc: / to IP addresses (and so far as a temporary solution, I assigned permanent IP addresses in the router on all computers on the local network). Once I afp: on a local computer, it appears on the side bar of the Finder under shared devices, well I saw several times it appears and then disappears. Nothing has changed on the network since the installation of Sierra.

• HP pavilion b005sa SSD Drive does not show?

  I just bought a hp pavilion b005sa 32 GB SSD and HDD of 750 GB. When looking, in my computer, the computer appears as below:

  

  but there is no indication of the SSD. Anyone know where he is? Or how to access it?

  Looking for a program called technology Intel Rapid Storage Technology. It will bring up a console showing the WSSD 32 gig 'speed up' the HDD main drive. The software combines in one volume so that you can't separately get the 32 GB drive to store files or something like that. It makes the system much faster startup and open frequently used files and applications much faster.

  If it's "the answer" Please click "Accept as Solution" to help others to find it. "

• Why flash does not show image after sealing the video?

  Hello

  I have the background layerand Bkg_Image layer and layer of video. I have embeded flv movie on video layer. On stage, it shows all the layers, but when I test the movie it shows only background layer and the layer of video. I do not see the Bkg_Image layer. Please let me know the cause.

  The Actions layer has swf external loading AS3 that works very well. Only the problem with Bkg_Image layer which is imprortant to me.

  How to solve the problem? Help, please.

  Thank you.

  

  When I test the movie, I see that in the snapshot following (just the Background_Image and video):

  

  Hi This is simply because your background shows that frame 1 - put your video in a MovieClip or expand frames on other layers to the number of images, the video needs.

  Booya

• Keys w custom image does not show up after export

  Hello

  I have a lot of buttons created with a custom image and all the fine features to the COP6, but after export to the .exe module buttons image in bulk and appear as white squares. It still works only lost image. Any ideas as to why?

  Thank you!

  Hello

  Welcome to the Adobe Forums.

  I tested this same workflow at my end and it worked for me, I used the "Image button" button instead of the "Transparent" and imported the image, screenshots:

  

  It could be useful!

  Thank you

  Vikram

• I just plugged my camera and uploaded new photos for my Creative Memories Photo Manager. Now when I go to the Safely Remove Hardware my camera does not show... only my external hard drive.

  I have a new computer.  We have been plug an external hard drive to move my photos in the new computer.

  I just plugged my camera and uploaded new photos for my Creative Memories Photo Manager.  Now when I go to the Safely Remove Hardware my camera does not show... only my external hard drive.  I'm afraid of getting my camera.

  Any help is greatly appreciated!
  Thank you
  Oumar W

  Creative Memories Photo Manager probably ejected your camera after you import the images. Check the default settings and change them if you prefer something different.

  If your camera is not displayed as ejection, it is safe to remove it. Damage to the file system wouldn't be possible, but not certain, if he had written active file or buffer not released when the device has been deleted.

• I tried EvevryThing! The "CREATED WITH ADOBE ELEMENTS 9 TRAIL VERSION FIRST" will not stop Displaying, even after I put in the serial number and Regerstered. Also the product does not show under my profile?

  I tried EvevryThing! The "CREATED WITH ADOBE ELEMENTS 9 TRAIL VERSION FIRST" will not stop Displaying, even after I put in the serial number and Regerstered. Also the product does not show under my profile?

  How can I fix it? Nothing in help or on the Site.

  Once you have registered the product, you should not see the banner of 'Trial' on NEW projects. This isn't the case, right? You only see on the project that you created before you register the product, right?

  That said, to remove the banner, go to the folder of directory on your hard drive where your project PREL files are stored and delete the folder called Adobe Premiere elements preview files.

• Checking update Java plug-in does not show latest version after update same

  Checking update Java plug-in does not show latest version after update same

  You exit and then restart your browser after Java update in order for the right version of Java to display the Plugin Check page. I felt it necessary to do so.

  See also:

  • Article on Java Mozilla - https://support.mozilla.org/en-US/kb/use-java-plugin-to-view-interactive-content
  • VΘrifier versions on site Java - http://www.java.com/en/download/installed.jsp

  Other - you should check your Plugins and update as needed.

  • Check your Plugins - https://www.mozilla.org/en-US/plugincheck/
  • Adobe Shockwave for Director Netscape plug-in, version 11.6.7.637 (aka Shockwave Player. Not the same as Flash/Shockwave Flash/Adobe Flash Player)
    • http://KB.mozillazine.org/Shockwave (mozillazine.org seems to be down at the moment (12/12/2012 11:34 am PDT), try again later)
    • Download, save, exit/close all browsers, run the installation program you just downloaded - http://get.adobe.com/shockwave/thankyou/
  • Adobe PDF plugin for Firefox and Netscape 10.1.4 (Adobe Reader 11 is the current version)
    • https://support.Mozilla.org/en-us/KB/use-Adobe-Reader-plugin-view-or-download-PDF-files

• CD/DVD drive does not work after 8 Win instalation

  Since a month since I've updated my windows in windows 8, everything works fine but the DVD - RW.

  When I put the blank cd and try to open it, it gives me error when opening by saying:
  "windows could not complete the format".

  Who's a software or a hardware problem?

  waiting for help!

  This means that your CD/DVD drive no longer works and is not recognized by the system?

  If Yes, then I would recommend checking this Toshiba document that I found on the portal of the knowledge base site:

  + Why my CD/DVD drive does not work after upgrade to Windows 8? +
  http://APS2.toshiba-tro.de/KB0/FAQ2B03F10002R01.htm

  You must uninstall the programs from Toshiba:
  TOSHIBA Recovery Media Creator
  TOSHIBA Disc Creator

• After the upgrade to win10 does not show the virtual keyboard in the taskbar

  After the Win10 the virtual keyboard does not show in the taskbar when you use programs that require to connect and it does not appear iwhen attempt to use Word (version Office365). These programs are therefore unusable, unless it is a workaround.  Does anyone know how to solve this or a work around for it?

  Hello m875,.

  What 'Tablet' do you use?

  I improved my tablet of 8 flow and had no problems.

  If you go to settings > devices > typing, you can enable and disable certain functions of touchpad.

  The last two options on the bottom are disabled by default. Can you turn those on to see if this gives you what you need?

  (Automatically display the touch keyboard in glass mode apps...)

  Once, when I type a mailbox type, the keyboard will appear.

  Does that help? Let me know.